
[Federal Register Volume 80, Number 178 (Tuesday, September 15, 2015)]
[Proposed Rules]
[Pages 55273-55275]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2015-22926]


 ========================================================================
 Proposed Rules
                                                 Federal Register
 ________________________________________________________________________
 
 This section of the FEDERAL REGISTER contains notices to the public of 
 the proposed issuance of rules and regulations. The purpose of these 
 notices is to give interested persons an opportunity to participate in 
 the rule making prior to the adoption of the final rules.
 
 ========================================================================
 

  Federal Register / Vol. 80, No. 178 / Tuesday, September 15, 2015 / 
Proposed Rules  

[[Page 55273]]



DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2015-3630; Directorate Identifier 2014-NM-253-AD]
RIN 2120-AA64


Airworthiness Directives; The Boeing Company Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to adopt a new airworthiness directive (AD) for all 
The Boeing Company Model 747-400F series airplanes. This proposed AD 
was prompted by an analysis of the production methods used to increase 
fatigue resistance of the upper closure fittings at the nose cargo door 
portal's C-3 frame, which indicated that cracking could start too early 
to be caught in a timely manner by the inspection or maintenance 
program. This proposed AD would require inspections of the upper 
closure fitting and connected strap and doubler at the nose cargo door 
portal for cracking, and related investigative and corrective actions 
if necessary. We are proposing this AD to detect and correct such 
cracking, which could result in sudden decompression and loss of the 
airplane's structural integrity.

DATES: We must receive comments on this proposed AD by October 30, 
2015.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    For service information identified in this proposed AD, contact 
Boeing Commercial Airplanes, Attention: Data & Services Management, 
P.O. Box 3707, MC 2H-65, Seattle, WA 98124-2207; telephone 206-544-
5000, extension 1; fax 206-766-5680; Internet https://www.myboeingfleet.com. You may view this referenced service information 
at the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., 
Renton, WA. For information on the availability of this material at the 
FAA, call 425-227-1221. It is also available on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2015-
3630.

Examining the AD Docket

    You may examine the AD docket on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2015-
3630; or in person at the Docket Management Facility between 9 a.m. and 
5 p.m., Monday through Friday, except Federal holidays. The AD docket 
contains this proposed AD, the regulatory evaluation, any comments 
received, and other information. The street address for the Docket 
Office (phone: 800-647-5527) is in the ADDRESSES section. Comments will 
be available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Bill Ashforth, Aerospace Engineer, 
Airframe Branch, ANM-120S, FAA, Seattle Aircraft Certification Office 
(ACO), 1601 Lind Avenue SW., Renton, WA 98057-3356; phone: 425-917-
6432; fax: 425-917-6590; email: bill.ashforth@faa.gov.

SUPPLEMENTARY INFORMATION:

Comments Invited

    We invite you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under the ADDRESSES section. Include ``Docket No. FAA-2015-3630; 
Directorate Identifier 2014-NM-253-AD'' at the beginning of your 
comments. We specifically invite comments on the overall regulatory, 
economic, environmental, and energy aspects of this proposed AD. We 
will consider all comments received by the closing date and may amend 
this proposed AD because of those comments.
    We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this proposed AD.

Discussion

    We have received a report indicating that an analysis of the 
production methods used to increase fatigue resistance of the upper 
closure fittings at the nose cargo door portal's C-3 frame showed that 
cracking could start too early to be caught in a timely manner by the 
inspection or maintenance program. The upper closure fittings used in 
the nose cargo door portal C-3 frame were shot peened to increase 
fatigue resistance. However, an analysis showed that the increase in 
fatigue resistance was still not enough to ensure that cracking would 
be caught by the inspection program specified in the Boeing 747-400 
maintenance planning data (MPD) document. This condition, if not 
detected and corrected, could result in sudden decompression and loss 
of the airplane's structural integrity.

Related Service Information Under 1 CFR Part 51

    We reviewed Boeing Alert Service Bulletin 747-53A2880, dated 
December 3, 2014. This service information describes procedures for a 
detailed inspection of the upper closure fitting and connected strap 
and doubler, a surface high frequency eddy current (HFEC) inspection of 
the upper closure fitting for cracking, and related investigative and 
corrective actions. This service information is reasonably available 
because the interested parties have access to it through their normal 
course of business or by the means identified in the ADDRESSES section 
of this NPRM.

FAA's Determination

    We are proposing this AD because we evaluated all the relevant 
information and determined the unsafe condition described previously is 
likely to exist or develop in other products of the same type design.

[[Page 55274]]

Proposed AD Requirements

    This proposed AD would require accomplishing the actions specified 
in the service information described previously, except as discussed 
under ``Differences Between this Proposed AD and the Service 
Information.'' Refer to this service information for information on the 
procedures and compliance times. For information on the procedures and 
compliance times, see this service information at http://www.regulations.gov by searching for and locating Docket No. FAA-2015-
3630.
    The phrase ``related investigative actions'' is used in this 
proposed AD. ``Related investigative actions'' are follow-on actions 
that (1) are related to the primary actions, and (2) further 
investigate the nature of any condition found. Related investigative 
actions in an AD could include, for example, inspections.
    The phrase ``corrective actions'' is used in this proposed AD. 
``Corrective actions'' are actions that correct or address any 
condition found. Corrective actions in an AD could include, for 
example, repairs.

Differences Between This Proposed AD and the Service Information

    Boeing Alert Service Bulletin 747-53A2880, dated December 3, 2014, 
specifies to contact the manufacturer for instructions on how to repair 
certain conditions, but this proposed AD would require repairing those 
conditions in one of the following ways:
     In accordance with a method that we approve; or
     Using data that meet the certification basis of the 
airplane, and that have been approved by the Boeing Commercial 
Airplanes Organization Designation Authorization (ODA) whom we have 
authorized to make those findings.

Costs of Compliance

    We estimate that this proposed AD affects 38 airplanes of U.S. 
registry. We estimate the following costs to comply with this proposed 
AD:

                                                 Estimated Costs
----------------------------------------------------------------------------------------------------------------
                                                                                                  Cost on U.S.
             Action                     Labor cost           Parts cost     Cost per product       operators
----------------------------------------------------------------------------------------------------------------
Inspections....................  9 work-hours x $85 per               $0   $765 per            $29,070 per
                                  hour = $765 per                           inspection cycle.   inspection
                                  inspection cycle.                                             cycle.
----------------------------------------------------------------------------------------------------------------

    We estimate the following costs to do any necessary repairs or 
replacements that would be required based on the results of the 
proposed inspection. Parts costs could be up to $42,930 per airplane. 
We have no way of determining the number of work hours (because the 
type of repair will vary depending on findings) or the number of 
aircraft that might need the repairs or replacements.

Explanation of ``RC'' Steps in Service Information

    The FAA worked in conjunction with industry, under the 
Airworthiness Directive Implementation Aviation Rulemaking Committee 
(ARC), to enhance the AD system. One enhancement was a new process for 
annotating which steps in the service information are required for 
compliance with an AD. Differentiating these steps from other tasks in 
the service information is expected to improve an owner's/operator's 
understanding of crucial AD requirements and help provide consistent 
judgment in AD compliance. The steps identified as Required for 
Compliance (RC) in any service information identified previously have a 
direct effect on detecting, preventing, resolving, or eliminating an 
identified unsafe condition.
    For service information that contains steps that are labeled as RC, 
the following provisions apply: (1) The steps labeled as RC, including 
substeps under an RC step and any figures identified in an RC step, 
must be done to comply with the AD, and an AMOC is required for any 
deviations to RC steps, including substeps and identified figures; and 
(2) steps not labeled as RC may be deviated from using accepted methods 
in accordance with the operator's maintenance or inspection program 
without obtaining approval of an AMOC, provided the RC steps, including 
substeps and identified figures, can still be done as specified, and 
the airplane can be put back in an airworthy condition.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979),
    (3) Will not affect intrastate aviation in Alaska, and
    (4) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

[[Page 55275]]

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

The Boeing Company: Docket No. FAA-2015-3630; Directorate Identifier 
2014-NM-253-AD.

(a) Comments Due Date

    We must receive comments by October 30, 2015.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to all The Boeing Company Model 747-400F series 
airplanes, certificated in any category, as identified in paragraph 
1.A., ``Effectivity,'' of Boeing Alert Service Bulletin 747-53A2880, 
dated December 3, 2014.

(d) Subject

    Air Transport Association (ATA) of America Code 53, Fuselage.

(e) Unsafe Condition

    This AD was prompted by a report that an analysis of the 
production methods used to increase fatigue resistance of the upper 
closure fittings at the nose cargo door portal's C-3 frame showed 
that cracking could still start too early to be caught in a timely 
manner by the inspection or maintenance program. We are issuing this 
AD to detect and correct such cracking, which could result in sudden 
decompression and loss of the airplane's structural integrity.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Inspections and Corrective Actions

    Except as required by paragraph (h) of this AD, at the 
applicable time specified in paragraph 1.E., ``Compliance,'' of 
Boeing Alert Service Bulletin 747-53A2880, dated December 3, 2014: 
Do a detailed inspection of the upper closure fitting, strap, and 
doubler and a surface high frequency eddy current (HFEC) inspection 
of the upper closure fitting at the nose cargo door portal for 
cracking, and do all applicable related investigative and corrective 
actions, in accordance with the Accomplishment Instructions of 
Boeing Alert Service Bulletin 747-53A2880, dated December 3, 2014. 
Repeat the inspections at the time specified in paragraph 1.E., 
``Compliance,'' of Boeing Alert Service Bulletin 747-53A2880, dated 
December 3, 2014. Do the applicable investigative and corrective 
actions at the times specified in paragraph 1.E., ``Compliance,'' of 
Boeing Alert Service Bulletin 747-53A2880, dated December 3, 2014.

(h) Exceptions to the Service Information

    (1) Where paragraph 1.E., ``Compliance,'' of Boeing Alert 
Service Bulletin 747-53A2880, dated December 3, 2014, refers to a 
compliance time ``after the original issue date of this service 
bulletin,'' this AD requires compliance within the specific 
compliance time after the effective date of this AD.
    (2) If any crack is found during any inspection required by this 
AD, and Boeing Alert Service Bulletin 747-53A2880, dated December 3, 
2014, specifies to contact Boeing for appropriate action: Before 
further flight, repair the cracking using a method approved in 
accordance with the procedures specified in paragraph (i) of this 
AD.

(i) Alternative Methods of Compliance (AMOCs)

    (1) The Manager, Seattle Aircraft Certification Office (ACO), 
FAA, has the authority to approve AMOCs for this AD, if requested 
using the procedures found in 14 CFR 39.19. In accordance with 14 
CFR 39.19, send your request to your principal inspector or local 
Flight Standards District Office, as appropriate. If sending 
information directly to the manager of the ACO, send it to the 
attention of the person identified in paragraph (j)(1) of this AD. 
Information may be emailed to: 9-ANM-Seattle-ACO-AMOC-Requests@faa.gov.
    (2) Before using any approved AMOC, notify your appropriate 
principal inspector, or lacking a principal inspector, the manager 
of the local flight standards district office/certificate holding 
district office.
    (3) An AMOC that provides an acceptable level of safety may be 
used for any repair required by this AD if it is approved by the 
Boeing Commercial Airplanes Organization Designation Authorization 
(ODA) that has been authorized by the Manager, Seattle ACO, to make 
those findings. For a repair method to be approved, the repair must 
meet the certification basis of the airplane, and the approval must 
specifically refer to this AD.
    (4) Except as required by paragraph (h)(2) of this AD: For 
service information that contains steps that are labeled as Required 
for Compliance (RC), the provisions of paragraphs (i)(4)(i) and 
(i)(4)(ii) apply.
    (i) The steps labeled as RC, including substeps under an RC step 
and any figures identified in an RC step, must be done to comply 
with the AD. An AMOC is required for any deviations to RC steps, 
including substeps and identified figures.
    (ii) Steps not labeled as RC may be deviated from using accepted 
methods in accordance with the operator's maintenance or inspection 
program without obtaining approval of an AMOC, provided the RC 
steps, including substeps and identified figures, can still be done 
as specified, and the airplane can be put back in an airworthy 
condition.

(j) Related Information

    (1) For more information about this AD, contact Bill Ashforth, 
Aerospace Engineer, Airframe Branch, ANM-120S, FAA, Seattle Aircraft 
Certification Office (ACO), 1601 Lind Avenue SW., Renton, WA 98057-
3356; phone: 425-917-6432; fax: 425-917-6590; email: 
bill.ashforth@faa.gov.
    (2) For service information identified in this AD, contact 
Boeing Commercial Airplanes, Attention: Data & Services Management, 
P.O. Box 3707, MC 2H-65, Seattle, WA 98124-2207; telephone 206-544-
5000, extension 1; fax 206-766-5680; Internet https://www.myboeingfleet.com. You may view this referenced service 
information at the FAA, Transport Airplane Directorate, 1601 Lind 
Avenue SW., Renton, WA. For information on the availability of this 
material at the FAA, call 425-227-1221.

    Issued in Renton, Washington, on September 2, 2015.
Jeffrey E. Duven,
Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2015-22926 Filed 9-14-15; 8:45 am]
 BILLING CODE 4910-13-P


