
[Federal Register Volume 80, Number 142 (Friday, July 24, 2015)]
[Proposed Rules]
[Pages 43972-43974]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2015-18151]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2015-2959; Directorate Identifier 2015-NM-008-AD]
RIN 2120-AA64


Airworthiness Directives; The Boeing Company Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to adopt a new airworthiness directive (AD) for 
certain The Boeing Company Model 787-8 airplanes. This proposed AD was 
prompted by reports indicating that the ram air turbine (RAT) assembly 
may fail to operate if deployed at low airspeeds. This proposed AD 
would require replacing either the RAT pump and control module assembly 
or the entire RAT assembly. We are proposing this AD to prevent failure 
of the RAT assembly to operate at low air speeds. The volume fuse on 
the RAT assembly may be activated in-flight before the RAT is deployed. 
This may lead to improper pump hydraulic pressure offloading when the 
RAT is needed. Failure of the RAT to operate in an all engine out event 
would result in loss of control of the airplane.

DATES: We must receive comments on this proposed AD by September 8, 
2015.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    For service information identified in this proposed AD, contact 
Boeing Commercial Airplanes, Attention: Data & Services Management, 
P.O. Box 3707, MC 2H-65, Seattle, WA 98124-2207; telephone 206-544-
5000, extension 1; fax 206-766-5680; Internet https://www.myboeingfleet.com. You may view this referenced service information 
at the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., 
Renton, WA. For information on the availability of this material at the 
FAA, call 425-227-1221. It is also available on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA 2015-
2959.

Examining the AD Docket

    You may examine the AD docket on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2015-
2959; or in person at the Docket Management Facility between 9 a.m. and 
5 p.m., Monday through Friday, except Federal holidays. The AD docket 
contains this proposed AD, the regulatory evaluation, any comments 
received, and other information. The street address for the Docket 
Office (phone: 800-647-5527) is in the ADDRESSES section. Comments will 
be available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Sean J. Schauer, Aerospace Engineer, 
Systems and Equipment Branch, ANM-130S, FAA, Seattle Aircraft 
Certification Office (ACO), 1601 Lind Avenue SW., Renton, WA 98057-
3356; phone: 425-917-6479; fax: 425-917-6590; email: 
sean.schauer@faa.gov.

SUPPLEMENTARY INFORMATION:

Comments Invited

    We invite you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under the ADDRESSES section. Include ``Docket No. FAA-2015-2959; 
Directorate Identifier 2015-NM-008-AD'' at the beginning of your 
comments. We specifically invite comments on the overall regulatory, 
economic, environmental, and energy aspects of this proposed AD. We 
will consider all comments received by the closing date and may amend 
this proposed AD because of those comments.
    We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this proposed AD.

Discussion

    An engineering review by Boeing's RAT supplier discovered that the 
RAT assembly may fail to operate if deployed at low airspeeds. A 
hydraulic fuse in the RAT control module is intended to remain open to 
enable RAT spin-up at low air speeds by off-loading the RAT hydraulic 
pump. After the RAT is spinning, the fuse sets and the pump

[[Page 43973]]

output supplies power to the center hydraulic system. The supplier 
found that the fuse may prematurely set as a result of nominal leakage 
through the hydraulic pump and/or check valve, preventing the RAT from 
spinning up when deployed below 160 knots. This has been attributed to 
a design defect in the fuse. A RAT in service will spin up if deployed 
above 160 knots and remain operational as the airplane decelerates 
through the minimum RAT design speed of 130 knots. The premature 
setting of the RAT fuse can prevent the RAT from spinning up and 
providing emergency hydraulic power when deployed below 160 knots. In 
an all engine out event, an inoperative RAT would result in loss of 
control of the airplane.

Related Service Information Under 1 CFR Part 51

    We reviewed Boeing Alert Service Bulletin B787-81205-SB290015-00, 
Issue 002, dated November 25, 2014. The service information describes 
procedures for replacing either the RAT pump and control module 
assembly or the RAT assembly including an installation test and 
corrective actions if necessary. This service information is reasonably 
available because the interested parties have access to it through 
their normal course of business or by the means identified in the 
ADDRESSES section of this NPRM.

FAA's Determination

    We are proposing this AD because we evaluated all the relevant 
information and determined the unsafe condition described previously is 
likely to exist or develop in other products of the same type design.

Proposed AD Requirements

    This proposed AD would require accomplishing the actions specified 
in the service information described previously. Refer to this service 
information for details on the procedures and compliance times.
    The phrase ``corrective actions'' is used in this proposed AD. 
``Corrective actions'' are actions that correct or address any 
condition found. Corrective actions in an AD could include, for 
example, repairs.

Explanation of ``RC'' Steps in Service Information

    The FAA worked in conjunction with industry, under the 
Airworthiness Directive Implementation Aviation Rulemaking Committee 
(ARC), to enhance the AD system. One enhancement was a new process for 
annotating which steps in the service information are required for 
compliance with an AD. Differentiating these steps from other tasks in 
the service information is expected to improve an owner's/operator's 
understanding of crucial AD requirements and help provide consistent 
judgment in AD compliance. The steps identified as RC (required for 
compliance) in any service information identified previously have a 
direct effect on detecting, preventing, resolving, or eliminating an 
identified unsafe condition.
    For service information that contains steps that are labeled as 
Required for Compliance (RC), the following provisions apply: (1) The 
steps labeled as RC, including substeps under an RC step and any 
figures identified in an RC step, must be done to comply with the AD, 
and an AMOC is required for any deviations to RC steps, including 
substeps and identified figures; and (2) steps not labeled as RC may be 
deviated from using accepted methods in accordance with the operator's 
maintenance or inspection program without obtaining approval of an 
AMOC, provided the RC steps, including substeps and identified figures, 
can still be done as specified, and the airplane can be put back in an 
airworthy condition.

Costs of Compliance

    We estimate that this proposed AD affects 12 airplanes of U.S. 
registry.
    We estimate the following costs to comply with this proposed AD:

                                                 Estimated Costs
----------------------------------------------------------------------------------------------------------------
                                                                                    Cost per       Cost on U.S.
              Action                     Labor cost            Parts cost           product         operators
----------------------------------------------------------------------------------------------------------------
Replacement.......................  7 work-hours x $85    N/A.................            $595           $7,140
                                     per hour = $595.
----------------------------------------------------------------------------------------------------------------

    According to the manufacturer, some of the costs of this proposed 
AD may be covered under warranty, thereby reducing the cost impact on 
affected individuals. We do not control warranty coverage for affected 
individuals. As a result, we have included all costs in our cost 
estimate.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979),
    (3) Will not affect intrastate aviation in Alaska, and
    (4) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

[[Page 43974]]

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

The Boeing Company: Docket No. FAA-2015-2959; Directorate Identifier 
2015-NM-008-AD.

(a) Comments Due Date

    We must receive comments by September 8, 2015.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to The Boeing Company Model 787-8 airplanes, 
certificated in any category, as identified in Boeing Alert Service 
Bulletin B787-81205-SB290015-00, Issue 002, dated November 25, 2014.

(d) Subject

    Air Transport Association (ATA) of America Code 29, Hydraulic 
Power.

(e) Unsafe Condition

    This AD was prompted by reports indicating that the ram air 
turbine (RAT) assembly may fail to operate if deployed at low 
airspeeds. We are issuing this AD to prevent failure of the RAT 
assembly to operate at low air speeds. The volume fuse on the RAT 
assembly may be activated in-flight before the RAT is deployed. This 
may lead to improper pump hydraulic pressure offloading when the RAT 
is needed. Failure of the RAT to operate in an all engine out event 
would result in loss of control of the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Replacement

    Within 36 months after the effective date of this AD, replace 
the RAT pump and control module assembly or the RAT assembly, 
including an installation test and applicable corrective actions, in 
accordance with the Accomplishment Instructions of Boeing Alert 
Service Bulletin B787-81205-SB290015-00, Issue 002, dated November 
25, 2014. Do all applicable corrective actions before further 
flight.

(h) Credit for Previous Actions

    This paragraph provides credit for actions required by paragraph 
(g) of this AD, if those actions were performed before the effective 
date of this AD using Boeing Alert Service Bulletin B787-81205-
SB290015-00, Issue 001, dated September 4, 2014, which is not 
incorporated by reference in this AD.

(i) Alternative Methods of Compliance (AMOCs)

    (1) The Manager, Seattle Aircraft Certification Office (ACO), 
FAA, has the authority to approve AMOCs for this AD, if requested 
using the procedures found in 14 CFR 39.19. In accordance with 14 
CFR 39.19, send your request to your principal inspector or local 
Flight Standards District Office, as appropriate. If sending 
information directly to the manager of the ACO, send it to the 
attention of the person identified in paragraph (j)(1) of this AD. 
Information may be emailed to: 9-ANM-Seattle-ACO-AMOC-Requests@faa.gov.
    (2) Before using any approved AMOC, notify your appropriate 
principal inspector, or lacking a principal inspector, the manager 
of the local flight standards district office/certificate holding 
district office.
    (3) An AMOC that provides an acceptable level of safety may be 
used for any repair required by this AD if it is approved by the 
Boeing Commercial Airplanes Organization Designation Authorization 
(ODA) that has been authorized by the Manager, Seattle ACO, to make 
those findings. For a repair method to be approved, the repair must 
meet the certification basis of the airplane, and the approval must 
specifically refer to this AD.
    (4) For service information that contains steps that are labeled 
as Required for Compliance (RC), the provisions of paragraphs 
(i)(4)(i) and (i)(4)(ii) of this AD apply.
    (i) The steps labeled as RC, including substeps under an RC step 
and any figures identified in an RC step, must be done to comply 
with the AD. An AMOC is required for any deviations to RC steps, 
including substeps and identified figures.
    (ii) Steps not labeled as RC may be deviated from using accepted 
methods in accordance with the operator's maintenance or inspection 
program without obtaining approval of an AMOC, provided the RC 
steps, including substeps and identified figures, can still be done 
as specified, and the airplane can be put back in an airworthy 
condition.

(j) Related Information

    (1) For more information about this AD, contact Sean J. Schauer, 
Aerospace Engineer, Systems and Equipment Branch, ANM 130S, FAA, 
Seattle Aircraft Certification Office (ACO), 1601 Lind Avenue SW., 
Renton, WA 98057-3356; phone: 425-917-6479; fax: 425-917-6590; 
email: sean.schauer@faa.gov.
    (2) For service information identified in this AD, contact 
Boeing Commercial Airplanes, Attention: Data & Services Management, 
P.O. Box 3707, MC 2H-65, Seattle, WA 98124-2207; telephone 206-544-
5000, extension 1; fax 206-766-5680; Internet https://www.myboeingfleet.com. You may view this referenced service 
information at the FAA, Transport Airplane Directorate, 1601 Lind 
Avenue SW., Renton, WA. For information on the availability of this 
material at the FAA, call 425-227-1221.

    Issued in Renton, Washington, on July 16, 2015.
Suzanne Masterson,
Acting Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2015-18151 Filed 7-23-15; 8:45 am]
BILLING CODE 4910-13-P


