
[Federal Register Volume 80, Number 70 (Monday, April 13, 2015)]
[Proposed Rules]
[Pages 19574-19576]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: 2015-08329]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2015-0822; Directorate Identifier 2014-NM-210-AD]
RIN 2120-AA64


Airworthiness Directives; Bombardier, Inc. Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to adopt a new airworthiness directive (AD) for 
certain Bombardier, Inc. Model CL-600-2C10 (Regional Jet Series 700, 
701, & 702) airplanes, Model CL-600-2D15 (Regional Jet Series 705) 
airplanes, Model CL-600-2D24 (Regional Jet Series 900) airplanes, and 
Model CL-600-2E25 (Regional Jet Series 1000) airplanes. This proposed 
AD was prompted by results of a design review indicating that the burst 
pressure of the flexible hose, used to vent oxygen from the high-
pressure relief valve of the oxygen cylinder overboard, was lower than 
the opening pressure of the high-pressure relief valve, which could 
cause the flexible hose to burst before it can vent the excess oxygen 
overboard. This proposed AD would require replacing the oxygen hose 
assembly with a new, improved assembly. We are proposing this AD to 
prevent the accumulation of oxygen in an enclosed space, which could 
result in an uncontrolled oxygen-fed fire if an ignition source is 
nearby.

DATES: We must receive comments on this proposed AD by May 28, 2015.

ADDRESSES: You may send comments by any of the following methods:
     Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: (202) 493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC 20590.
     Hand Delivery: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC, between 9 a.m. and 5 p.m., Monday 
through Friday, except Federal holidays.
    For service information identified in this proposed AD, contact 
Bombardier, Inc., 400 C[ocirc]te-Vertu Road West, Dorval, Qu[eacute]bec 
H4S 1Y9, Canada; telephone 514-855-5000; fax 514-855-7401; email 
thd.crj@aero.bombardier.com; Internet http://www.bombardier.com. You 
may view this referenced service information at the FAA, Transport 
Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For information 
on the availability of this material at the FAA, call 425-227-1221.

Examining the AD Docket

    You may examine the AD docket on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2015-
0822; or in person at the Docket Management Facility between 9 a.m. and 
5 p.m., Monday through Friday,

[[Page 19575]]

except Federal holidays. The AD docket contains this proposed AD, the 
regulatory evaluation, any comments received, and other information. 
The street address for the Docket Operations office (telephone (800) 
647-5527) is in the ADDRESSES section. Comments will be available in 
the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Cesar Gomez, Aerospace Engineer, 
Airframe and Mechanical Systems Branch, ANE-171, FAA, New York Aircraft 
Certification Office, 1600 Stewart Avenue, Suite 410, Westbury, NY 
11590; telephone (516) 228-7318; fax (516) 794-5531.

SUPPLEMENTARY INFORMATION:

Comments Invited

    We invite you to send any written relevant data, views, or 
arguments about this proposed AD. Send your comments to an address 
listed under the ADDRESSES section. Include ``Docket No. FAA-2015-0822; 
Directorate Identifier 2014-NM-210-AD'' at the beginning of your 
comments. We specifically invite comments on the overall regulatory, 
economic, environmental, and energy aspects of this proposed AD. We 
will consider all comments received by the closing date and may amend 
this proposed AD based on those comments.
    We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this proposed AD.

Discussion

    Transport Canada Civil Aviation (TCCA), which is the airworthiness 
authority for Canada, has issued Canadian Airworthiness Directive CF-
2014-37, dated October 17, 2014 (referred to after this as the 
Mandatory Continuing Airworthiness Information, or ``the MCAI''), to 
correct an unsafe condition for certain Bombardier, Inc. Model CL-600-
2C10 (Regional Jet Series 700, 701, & 702) airplanes, Model CL-600-2D15 
(Regional Jet Series 705) airplanes, Model CL-600-2D24 (Regional Jet 
Series 900) airplanes, and Model CL-600-2E25 (Regional Jet Series 1000) 
airplanes. The MCAI states:

    Design review found that the burst pressure of the flexible 
hose, used to vent oxygen from the high-pressure relief valve of the 
oxygen cylinder overboard, is lower than the opening pressure of the 
high-pressure relief valve. This could cause the flexible hose to 
burst before it is able to vent the excess oxygen overboard. If an 
ignition source is present, the accumulation of oxygen in an 
enclosed space may result in an uncontrolled oxygen-fed fire.
    This [Canadian] AD mandates the replacement of the oxygen hose 
assembly with a new design oxygen hose assembly.

    You may examine the MCAI in the AD docket on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2015-
0822.

Related Service Information Under 1 CFR Part 51

    Bombardier has issued Service Bulletin 670BA-35-013, Revision A, 
dated September 23, 2013, including Appendix A, dated May 21, 2013. The 
service information describes procedures for replacing the oxygen hose 
assembly with a new, improved assembly. The actions described in this 
service information are intended to correct the unsafe condition 
identified in the MCAI. This service information is reasonably 
available; see ADDRESSES for ways to access this service information.

FAA's Determination and Requirements of This Proposed AD

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to our bilateral agreement with the State of Design Authority, we have 
been notified of the unsafe condition described in the MCAI and service 
information referenced above. We are proposing this AD because we 
evaluated all pertinent information and determined an unsafe condition 
exists and is likely to exist or develop on other products of the same 
type design.

Costs of Compliance

    We estimate that this proposed AD affects 400 airplanes of U.S. 
registry.
    We also estimate that it would take about 10 work-hours per product 
to comply with the basic requirements of this proposed AD. Required 
parts would cost about $0 per product. The average labor rate is $85 
per work-hour. Based on these figures, we estimate the cost of this 
proposed AD on U.S. operators to be $340,000, or $850 per airplane.
    According to the manufacturer, some of the costs of this proposed 
AD may be covered under warranty, thereby reducing the cost impact on 
affected individuals. We do not control warranty coverage for affected 
individuals. As a result, we have included all costs in our cost 
estimate

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more detail the scope of the Agency's 
authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979);
    3. Will not affect intrastate aviation in Alaska; and
    4. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):


[[Page 19576]]


Bombardier, Inc.: Docket No. FAA-2015-0822; Directorate Identifier 
2014-NM-210-AD.

(a) Comments Due Date

    We must receive comments by May 28, 2015.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to the airplanes, certificated in any category, 
identified in paragraphs (c)(1), (c)(2), and (c)(3) of this AD.
    (1) Bombardier, Inc. Model CL-600-2C10 (Regional Jet Series 700, 
701, & 702) airplanes, serial numbers 10002 through 10336 inclusive.
    (2) Bombardier, Inc. Model CL-600-2D15 (Regional Jet Series 
705), and Model CL-600-2D24 (Regional Jet Series 900) airplanes, 
serial numbers 15001 through 15297 inclusive.
    (3) Bombardier, Inc. Model CL-600-2E25 (Regional Jet Series 
1000) airplanes, serial numbers 19001 through 19038 inclusive.

(d) Subject

    Air Transport Association (ATA) of America Code 35, Oxygen.

(e) Reason

    This AD was prompted by results of a design review indicating 
that the burst pressure of the flexible hose, used to vent oxygen 
from the high-pressure relief valve of the oxygen cylinder 
overboard, was lower than the opening pressure of the high-pressure 
relief valve, which could cause the flexible hose to burst before it 
can vent the excess oxygen overboard. We are issuing this AD to 
prevent the accumulation of oxygen in an enclosed space, which could 
result in an uncontrolled oxygen-fed fire if an ignition source is 
nearby.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Replacement

    Before the accumulation of 5,800 total flight hours, or within 
44 months after the effective date of this AD, whichever occurs 
first, replace all oxygen hose assemblies having part number (P/N) 
S6946-01 with new, improved assemblies having P/N BA670-44025-001, 
in accordance with the Accomplishment Instructions of Bombardier 
Service Bulletin 670BA-35-013, Revision A, dated September 23, 2013, 
including Appendix A, dated May 21, 2013. For airplanes on which 
Supplemental Type Certificate ST01648NY (http://rgl.faa.gov/
Regulatory_and_Guidance_Library/rgstc.nsf/0/
ebd1cec7b301293e86257cb30045557a/$FILE/ST01648NY.pdf) is installed, 
only PART B of the Accomplishment Instructions of Bombardier Service 
Bulletin 670BA-35-013, Revision A, dated September 23, 2013, is 
required.

(h) Credit for Previous Actions

    This paragraph provides credit for the replacement specified in 
paragraph (g) of this AD, if that action was performed before the 
effective date of this AD using Bombardier Service Bulletin 670BA-
35-013, dated May 21, 2013, which is not incorporated by reference 
in this AD.

(i) Parts Installation Prohibition

    As of the effective date of this AD, no person may install an 
oxygen hose assembly, P/N S6946-01, on any airplane.

(j) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, New 
York Aircraft Certification Office (ACO), ANE-170, FAA, has the 
authority to approve AMOCs for this AD, if requested using the 
procedures found in 14 CFR 39.19. Send information to ATTN: Program 
Manager, Continuing Operational Safety, FAA, New York ACO, 1600 
Stewart Avenue, Suite 410, Westbury, NY 11590; telephone 516-228-
7300; fax 516-794-5531. Before using any approved AMOC, notify your 
appropriate principal inspector, or lacking a principal inspector, 
the manager of the local flight standards district office/
certificate holding district office. The AMOC approval letter must 
specifically reference this AD.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain corrective actions from a manufacturer, the action must be 
accomplished using a method approved by the Manager, New York ACO, 
ANE-170, FAA; or Transport Canada Civil Aviation (TCCA); or 
Bombardier, Inc.'s TCCA Design Approval Organization (DAO). If 
approved by the DAO, the approval must include the DAO-authorized 
signature.

(k) Related Information

    (1) Refer to Mandatory Continuing Airworthiness Information 
(MCAI) Canadian Airworthiness Directive CF-2014-37, dated October 
17, 2014, for related information. This MCAI may be found in the AD 
docket on the Internet at http://www.regulations.gov by searching 
for and locating Docket No. FAA-2015-0822.
    (2) For service information identified in this AD, contact 
Bombardier, Inc., 400 C[ocirc]te-Vertu Road West, Dorval, 
Qu[eacute]bec H4S 1Y9, Canada; telephone 514-855-5000; fax 514-855-
7401; email thd.crj@aero.bombardier.com; Internet http://www.bombardier.com. You may view this service information at the 
FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, 
WA. For information on the availability of this material at the FAA, 
call 425-227-1221.

    Issued in Renton, Washington, on March 27, 2015.
Michael Kaszycki,
Acting Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2015-08329 Filed 4-10-15; 8:45 am]
 BILLING CODE 4910-13-P


