
[Federal Register Volume 80, Number 32 (Wednesday, February 18, 2015)]
[Proposed Rules]
[Pages 8564-8566]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: 2015-02695]


=======================================================================
-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2015-0088; Directorate Identifier 2014-NM-179-AD]
RIN 2120-AA64


Airworthiness Directives; Bombardier, Inc. Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to adopt a new airworthiness directive (AD) for 
certain Bombardier, Inc. Model BD-100-1A10 (Challenger 300) airplanes. 
This proposed AD was prompted by testing of the spoiler electronic 
control unit (SECU) software for an upgrade, which revealed a timing 
error between the command and monitor channels. This proposed AD would 
require revising the maintenance or inspection program to incorporate 
repetitive operational tests of the aileron disconnect system, and 
corrective action if necessary. This proposed AD would also require 
modification and reidentification of the SECU, which would terminate 
the repetitive operational tests. We are proposing this AD to prevent a 
timing error in the SECU software, which, in combination with failure 
of the roll disconnect switch, could result in complete loss of spoiler 
functionality and consequent reduced controllability of the airplane.

DATES: We must receive comments on this proposed AD by April 6, 2015.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC 20590.
     Hand Delivery: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC, between 9 a.m. and 5 p.m., Monday 
through Friday, except Federal holidays.
    For service information identified in this proposed AD, contact 
Bombardier, Inc., 400 C[ocirc]te-Vertu Road West, Dorval, Qu[eacute]bec 
H4S 1Y9, Canada; telephone 514-855-5000; fax 514-855-7401; email 
thd.crj@aero.bombardier.com; Internet http://www.bombardier.com. You 
may view this referenced service information at the FAA, Transport 
Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For information 
on the availability of this material at the FAA, call 425-227-1221.

Examining the AD Docket

    You may examine the AD docket on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2015-
0088; or in person at the Docket Management Facility between 9 a.m. and 
5 p.m., Monday through Friday, except Federal holidays. The AD docket 
contains this proposed AD, the regulatory evaluation, any comments 
received, and other information. The street address for the Docket 
Operations office (telephone 800-647-5527) is in the ADDRESSES section. 
Comments will be available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Assata Dessaline, Aerospace Engineer, 
Avionics and Service Branch, ANE-172, FAA, New York Aircraft 
Certification Office, 1600 Stewart Avenue, Suite 410, Westbury, New 
York 11590; telephone 516-228-7301; fax 516-794-5531.

SUPPLEMENTARY INFORMATION:

Comments Invited

    We invite you to send any written relevant data, views, or 
arguments about this proposed AD. Send your comments to an address 
listed under the ADDRESSES section. Include ``Docket No. FAA-2015-0088; 
Directorate Identifier 2014-NM-179-AD'' at the beginning of your 
comments. We specifically invite comments on the overall regulatory, 
economic, environmental, and energy aspects of this proposed AD. We 
will consider all comments received by the closing date and may amend 
this proposed AD based on those comments.
    We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this proposed AD.

Discussion

    Transport Canada Civil Aviation (TCCA), which is the aviation 
authority for Canada, has issued Canadian Airworthiness Directive CF-
2014-24, dated August 5, 2014 (referred to after this as the Mandatory 
Continuing Airworthiness Information, or ``the MCAI''), to correct an 
unsafe condition for certain Bombardier, Inc. Model BD-

[[Page 8565]]

100-1A10 (Challenger 300) airplanes. The MCAI states:

    During testing of the software for an upgrade of the spoiler 
electronic control unit (SECU), a timing error between the Command 
and Monitor channels was found in the SECU software. This timing 
error, if not corrected, in combination with the failure of the roll 
disconnect switch, may lead to a complete loss of spoiler 
functionality and result in a reduction or complete loss of 
aeroplane roll control.
    This [TCCA] AD mandates the SECU software modification to 
correct the timing error and to change the inspection interval for a 
maintenance task based on System Functional Hazard Analysis [by 
revising the inspection or maintenance program.]

    You may examine the MCAI in the AD docket on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2015-
0088.

Related Service Information Under 1 CFR Part 51

    Bombardier, Inc. has issued Service Bulletin 100-27-16, dated 
October 31, 2013. The service information describes procedures for 
modification and reidentification of the SECU. The actions described in 
this service information are intended to correct the unsafe condition 
identified in the MCAI. This service information is reasonably 
available; see ADDRESSES for ways to access this service information.

FAA's Determination and Requirements of This Proposed AD

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to our bilateral agreement with the State of Design Authority, we have 
been notified of the unsafe condition described in the MCAI and service 
information referenced above. We are proposing this AD because we 
evaluated all pertinent information and determined an unsafe condition 
exists and is likely to exist or develop on other products of the same 
type design.
    This AD requires revisions to certain operator maintenance 
documents to include new actions (e.g., inspections). Compliance with 
these actions is required by 14 CFR 91.403(c). For airplanes that have 
been previously modified, altered, or repaired in the areas addressed 
by this AD, the operator may not be able to accomplish the actions 
described in the revisions. In this situation, to comply with 14 CFR 
91.403(c), the operator must request approval for an alternative method 
of compliance according to paragraph (j)(1) of this AD. The request 
should include a description of changes to the required inspections 
that will ensure the continued operational safety of the airplane.

Costs of Compliance

    We estimate that this proposed AD affects 107 airplanes of U.S. 
registry.
    We also estimate that it would take up to 6 work-hours per product 
to comply with the basic requirements of this proposed AD. The average 
labor rate is $85 per work-hour. Based on these figures, we estimate 
the cost of this proposed AD on U.S. operators to be up to $54,570, or 
up to $510 per product.
    We have received no definitive data on the parts cost for doing the 
modification in this proposed AD.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more detail the scope of the Agency's 
authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979);
    3. Will not affect intrastate aviation in Alaska; and
    4. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

Bombardier, Inc.: Docket No. FAA-2015-0088; Directorate Identifier 
2014-NM-179-AD.

(a) Comments Due Date

    We must receive comments by April 6, 2015.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Bombardier, Inc. Model BD-100-1A10 
(Challenger 300) airplanes, equipped with a spoiler electronic 
control unit (SECU) having part number (P/N) C47330-006, C47330-007, 
or C47330-008; certificated in any category.

(d) Subject

    Air Transport Association (ATA) of America Code 27, Flight 
Controls.

(e) Reason

    This AD was prompted by testing of the spoiler electronic 
control unit (SECU) software, which revealed a timing error between 
the command and monitor channels in the software. We are issuing 
this AD to prevent a timing error in the SECU software, which, in 
combination with failure of the roll disconnect switch, could result 
in complete loss of spoiler functionality and consequent reduced 
controllability of the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Revise the Maintenance or Inspection Program

    Within 600 flight hours since the most recent operational test 
of the aileron disconnect system for spoiler functionality as of the 
effective date of this AD, or within 400 flight hours after the 
effective date of this AD, whichever occurs first: Revise the 
maintenance or inspection program, as applicable, to incorporate 
repetitive operational tests of the aileron disconnect system for 
spoiler functionality, and all

[[Page 8566]]

applicable corrective actions, using a method approved by the 
Manager, New York ACO, ANE-170, FAA.
    Note 1 to paragraph (g) of this AD: Guidance on operational 
tests of the aileron disconnect system can be found in the BD-100-
1A10 Time Limits/Maintenance Checks (TLMC) Manual.

(h) Modification of the SECU

    Within 1,600 flight hours or 48 months after the effective date 
of this AD, whichever occurs first: Modify and re-identify the SECU, 
in accordance with the Accomplishment Instructions of Bombardier 
Service Bulletin 100-27-16, dated October 31, 2013. Doing the 
actions required by this paragraph terminates the actions required 
by paragraph (g) of this AD.

(i) Parts Installation Prohibition

    As of the effective date of this AD, no person may install an 
SECU, P/N C47330-006, C47330-007, or C47330-008, on any airplane.

(j) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, New 
York Aircraft Certification Office (ACO), ANE-170, FAA, has the 
authority to approve AMOCs for this AD, if requested using the 
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, 
send your request to your principal inspector or local Flight 
Standards District Office, as appropriate. If sending information 
directly to the ACO, send it to ATTN: Program Manager, Continuing 
Operational Safety, FAA, New York ACO, 1600 Stewart Avenue, Suite 
410, Westbury, NY 11590; telephone 516-228-7300; fax 516-794-5531. 
Before using any approved AMOC, notify your appropriate principal 
inspector, or lacking a principal inspector, the manager of the 
local flight standards district office/certificate holding district 
office. The AMOC approval letter must specifically reference this 
AD.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain corrective actions from a manufacturer, the action must be 
accomplished using a method approved by the Manager, New York ACO, 
ANE-170, FAA; or TCCA; or Bombardier, Inc.'s TCCA DAO. If approved 
by the DAO, the approval must include the DAO-authorized signature.

(k) Related Information

    (1) Refer to Mandatory Continuing Airworthiness Information 
(MCAI) Canadian Airworthiness Directive CF-2014-24, dated August 5, 
2014, for related information. This MCAI may be found in the AD 
docket on the Internet at http://www.regulations.gov by searching 
for and locating Docket No. FAA-FAA-2015-0088.
    (2) For service information identified in this AD, contact 
Bombardier, Inc., 400 C[ocirc]te-Vertu Road West, Dorval, 
Qu[eacute]bec H4S 1Y9, Canada; telephone 514-855-5000; fax 514-855-
7401; email thd.crj@aero.bombardier.com; Internet http://www.bombardier.com. You may view this service information at the 
FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, 
WA. For information on the availability of this material at the FAA, 
call 425-227-1221.

    Issued in Renton, Washington, on February 2, 2015.
Dionne Palermo,
Acting Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2015-02695 Filed 2-17-15; 8:45 am]
BILLING CODE 4910-13-P


