
[Federal Register Volume 80, Number 15 (Friday, January 23, 2015)]
[Proposed Rules]
[Pages 3516-3520]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: 2015-00994]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2014-1044; Directorate Identifier 2014-NM-148-AD]
RIN 2120-AA64


Airworthiness Directives; Cessna Aircraft Company Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to adopt a new airworthiness directive (AD) for 
certain Cessna Aircraft Company Model 500, 501, 550, 551, S550, 560, 
and 650 airplanes. This proposed AD was prompted by reports of smoke 
and/or fire in the tailcone caused by sparking due to excessive wear of 
the brushes in the air conditioning (A/C) motor. This proposed AD would 
require inspections to determine if certain A/C compressor motors are 
installed and to determine the accumulated hours on certain A/C 
compressor motor assemblies; and repetitive replacement of the brushes 
in the A/C compressor motor assembly, or, as an option to the brush 
replacement, deactivation of the A/C system and placard installation; 
and return of replaced brushes to Cessna. We are proposing this AD to 
prevent the brushes in the A/C motor from wearing down beyond their 
limits, which could result in the rivet in the brush contacting the 
commutator, causing sparks and consequent fire and/or smoke in the 
tailcone with no means to detect or extinguish the fire and/or smoke.

DATES: We must receive comments on this proposed AD by March 9, 2015.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    For service information identified in this proposed AD, contact 
Cessna Aircraft Co., P.O. Box 7706, Wichita, KS 67277; telephone 316-
517-6215; fax 316-517-5802; email citationpubs@cessna.textron.com; 
Internet https://www.cessnasupport.com/newlogin.html. You may view this 
referenced service information at the FAA, Transport Airplane 
Directorate, 1601 Lind Avenue SW., Renton, WA. For information on the 
availability of this material at the FAA, call 425-227-1221.

Examining the AD Docket

    You may examine the AD docket on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2014-
1044; or in person at the Docket Management Facility between 9 a.m. and 
5 p.m., Monday through Friday, except Federal holidays. The AD docket 
contains this proposed AD, the regulatory evaluation, any comments 
received, and other information. The street address for the Docket 
Office (phone: 800-647-5527) is in the ADDRESSES section. Comments will 
be available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Craig Henrichsen, Aerospace Engineer, 
Electrical Systems and Avionics Branch, ACE-119W, FAA, Wichita Aircraft 
Certification Office (ACO), 1801 Airport Road, Room 100, Mid-Continent 
Airport, Wichita, KS 67209; phone: 316-946-4110; fax: 316-946-4107; 
email: Craig.Henrichsen@faa.gov.

SUPPLEMENTARY INFORMATION:

Comments Invited

    We invite you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under the ADDRESSES section. Include ``Docket No. FAA-2014-1044; 
Directorate Identifier 2014-NM-148-AD'' at the beginning of your 
comments. We specifically invite comments on the overall regulatory, 
economic, environmental, and energy aspects of this proposed AD. We 
will consider all comments received by the closing date and may amend 
this proposed AD because of those comments.
    We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this proposed AD.

Discussion

    We have received reports of smoke/fire (three reports of fire) in 
the tailcone of Cessna Aircraft Company Model 525, 550, and 560 
airplanes, where investigation revealed brushes had worn

[[Page 3517]]

beyond their limits on the part number (P/N) 1134104-1 A/C compressor 
motors. The motor assembly is located in the airplane tailcone where 
flammable fluids in the form of fuel lines and hydraulics are present. 
There is no fire detection or extinguishing system in the tailcone. We 
are proposing this AD to prevent the brushes in the air conditioning 
motor from wearing down beyond their limits, which could result in the 
rivet in the brush contacting the commutator, causing sparks and 
consequent fire and/or smoke in the tailcone with no means to detect or 
extinguish the fire and/or smoke.
    The subject part, P/N 1134104-1 A/C compressor motors, might also 
be installed on Model 500, 501, 551, S550, and 650 airplanes. 
Therefore, those Model 500, 501, 551, S550, and 650 airplanes might be 
subject to the unsafe condition revealed on Model 525, 550, and 560 
airplanes.

Related ADs

    AD 2013-09-11, Amendment 39-17453 (78 FR 32349, May 30, 2013), was 
issued for certain Cessna Aircraft Company Model 500, 501, 550, 551, 
S550, 560, 560XL, and 650 airplanes. AD 2013-09-11 requires inspecting 
to determine if certain A/C compressor motors are installed and to 
determine the accumulated hours on certain A/C compressor motor 
assemblies; and repetitive replacement of the brushes in the A/C 
compressor motor assembly, or, as an option to the brush replacement, 
deactivation of the A/C system and placard installation; and return of 
replaced brushes to Cessna.
    After AD 2013-09-11, Amendment 39-17453 (78 FR 32349, May 30, 
2013), was published the FAA received several questions asking if AD 
2013-09-11 is applicable to airplanes having an air conditioning system 
installed via any of the following Fort Worth Airworks supplemental 
type certificates (STCs):
     SA3849SW (http://rgl.faa.gov/Regulatory_and_Guidance_Library/rgstc.nsf/0/029C5719AD18E79C86257C1A0069742C?OpenDocument&Highlight=sa3849sw);
     SA7580SW (http://rgl.faa.gov/Regulatory_and_Guidance_Library/rgstc.nsf/0/7C9B0FB7D5923D4986257C1A0069E2C0?OpenDocument&Highlight=sa7580sw);
     SA7753SW (http://rgl.faa.gov/Regulatory_and_Guidance_Library/rgstc.nsf/0/A78233CBB3314BAF86257C1A0069D128?OpenDocument&Highlight=sa7753sw); or
     SA8918SW (http://rgl.faa.gov/Regulatory_and_Guidance_Library/rgstc.nsf/0/5FAD7ABA3EAA464C86257C1A0069F239?OpenDocument&Highlight=sa8918sw).
    The A/C compressor motor part numbers installed via these STCs are 
the same as in AD 2013-09-11, except the prefix ``FWA'' has been added 
to the part numbers of the A/C compressor motor installed via the STCs 
(FWA1134104-1 or FWA1134104-5).
    Based on a discussion between the FAA and Cessna, we determined 
that AD 2013-09-11, Amendment 39-17453 (78 FR 32349, May 30, 2013), 
should also apply to A/C compressor motor airplanes with P/N 
FWA1134104-1 or P/N FWA1134104-5 installed. Instead of superseding AD 
2013-09-11 to add these airplanes to the applicability, the FAA is 
issuing this new proposed AD applicable only to airplanes with P/N 
FWA1134104-1 or P/N FWA1134104-5 installed.
    Cessna Model 560XL airplanes are not included in the applicability 
of this proposed AD because the Fort Worth Airworks STCs identified 
previously are not installed on that airplane model.
    AD 2013-08-05, Amendment 39-17422 (78 FR 24343, April 25, 2013), 
addresses the same unsafe condition that prompted this proposed AD. AD 
2013-08-05 is applicable to Cessna Aircraft Company Model 525 
airplanes. The Fort Worth Airworks STCs referenced above do not apply 
to the Cessna Model 525 airplanes; therefore, this proposed AD does not 
affect AD 2013-08-05.
    After AD 2013-08-05, Amendment 39-17422 (78 FR 24343, April 25, 
2013); and AD 2013-09-11, Amendment 39-17453 (78 FR 32349, May 30, 
2013); were published, the FAA determined that there are some airplanes 
on which the air conditioning motor system had been installed via the 
Fort Worth Airworks STCs mentioned previously, and an A/C compressor 
hour meter was not part of the type design. To assist in future 
compliance with this proposed AD, an A/C compressor hour meter may be 
installed. The installation can be done using Cessna Service Letter 
CIL-21-02, dated January 23, 2014, or by a method approved by the FAA.

Related Service Information

    We have reviewed the following service information, which describes 
procedures for replacement of life-limited components including P/N 
FWA1134104-1 or FWA1134104-5 A/C compressor motor brushes.
     Subject 4-11-00, Replacement Time Limits, of Chapter 4, 
Airworthiness Limitations, Revision 6, dated June 23, 2014, of the 
Cessna Model 500/501 Maintenance Manual.
     Subject 4-11-00, Replacement Time Limits, of Chapter 4, 
Airworthiness Limitations, Revision 10, dated June 23, 2014, of the 
Cessna Model 550/551 Maintenance Manual.
     Subject 4-11-00, Replacement Time Limits, of Chapter 4, 
Airworthiness Limitations, Revision 12, dated June 23, 2014, of the 
Cessna Model 550 Bravo Maintenance Manual.
     Subject 4-11-00, Replacement Time Limits, of Chapter 4, 
Airworthiness Limitations, Revision 9, dated June 23, 2014, of the 
Cessna Model S550 Maintenance Manual.
     Subject 4-11-00, Replacement Time Limits, of Chapter 4, 
Airworthiness Limitations, Revision 22, dated June 23, 2014, of the 
Cessna Model 560 Maintenance Manual.
     Subject 4-11-00, Replacement Time Limits, of Chapter 4, 
Airworthiness Limitations, Revision 32, dated June 23, 2014, of the 
Cessna Model 650 Maintenance Manual.

FAA's Determination

    We are proposing this AD because we evaluated all the relevant 
information and determined the unsafe condition described previously is 
likely to exist or develop in other products of these same type 
designs.

Proposed AD Requirements

    This proposed AD would require an inspection to determine if 
certain A/C compressor motors are installed; an inspection of the A/C 
compressor hour meter for certain A/C compressor motors to determine 
the number of hours accumulated on the motors; and repetitive 
replacement of the brushes in the A/C compressor motor assembly, or 
optional deactivation of the A/C system and installation of a placard 
prohibiting use of the A/C system until replacement of the brushes. 
This proposed AD would also require, when the brushes are replaced, 
reporting aircraft information related to the replacement of the 
brushes and sending the replaced motor brushes to Cessna Aircraft 
Company for two replacement cycles.

Interim Action

    We consider this proposed AD interim action. The reporting data 
required by this proposed AD will enable us to obtain better insight 
into brush wear. The reporting data will also indicate if the 
replacement intervals we established are adequate. After we analyze the 
reporting data received, we might consider further rulemaking.

Costs of Compliance

    We estimate that this proposed AD affects 333 airplanes of U.S. 
registry.

[[Page 3518]]

    We estimate the following costs to comply with this proposed AD:

                                       Estimated Costs--Brush Replacement
----------------------------------------------------------------------------------------------------------------
                                                                                                 Cost on U.S.
              Action                    Labor cost        Parts cost      Cost per product        operators
----------------------------------------------------------------------------------------------------------------
Inspection and replacement.......  11 work-hours x $85            $252  $1,187 per           $395,271 per
                                    per hour = $935                      replacement cycle.   replacement cycle.
                                    per replacement
                                    cycle.
Reporting/return parts...........  1 work-hour x $85                $0  $85................  $4,995 per return
                                    per hour = $85 per                                        (2 returns
                                    return.                                                   required).
----------------------------------------------------------------------------------------------------------------


                                        Estimated Costs--A/C Deactivation
----------------------------------------------------------------------------------------------------------------
                                                                                                     Cost per
                    Action                                 Labor cost               Parts cost        product
----------------------------------------------------------------------------------------------------------------
Fabrication of placard for A/C deactivation...  1 work-hour x $85 per hour = $85              $0             $85
Deactivation/reactivation of A/C..............  1 work-hour x $85 per hour = $85               0              85
----------------------------------------------------------------------------------------------------------------

Paperwork Reduction Act

    A federal agency may not conduct or sponsor, and a person is not 
required to respond to, nor shall a person be subject to penalty for 
failure to comply with a collection of information subject to the 
requirements of the Paperwork Reduction Act unless that collection of 
information displays a current valid OMB control number. The control 
number for the collection of information required by this AD is 2120-
0056. The paperwork cost associated with this AD has been detailed in 
the Costs of Compliance section of this document and includes time for 
reviewing instructions, as well as completing and reviewing the 
collection of information. Therefore, all reporting associated with 
this AD is mandatory. Comments concerning the accuracy of this burden 
and suggestions for reducing the burden should be directed to the FAA 
at 800 Independence Ave. SW., Washington, DC 20591, ATTN: Information 
Collection Clearance Officer, AES-200.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979),
    (3) Will not affect intrastate aviation in Alaska, and
    (4) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

Cessna Aircraft Company: Docket No. FAA-2014-1044; Directorate 
Identifier 2014-NM-148-AD.

(a) Comments Due Date

    We must receive comments by March 9, 2015.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to the Cessna Aircraft Company airplanes, 
certificated in any category, identified in table 1 to paragraph (c) 
of this AD, that have an air conditioning system installed via a 
Fort Worth Airworks supplemental type certificate (STC) identified 
in paragraph (c)(1), (c)(2), (c)(3), or (c)(4) of this AD.
    (1) SA3849SW (http://rgl.faa.gov/Regulatory_and_Guidance_Library/rgstc.nsf/0/029C5719AD18E79C86257C1A0069742C?OpenDocument&Highlight=sa3849sw).
    (2) SA7580SW (http://rgl.faa.gov/Regulatory_and_Guidance_Library/rgstc.nsf/0/7C9B0FB7D5923D4986257C1A0069E2C0?OpenDocument&Highlight=sa7580sw).
    (3) SA7753SW (http://rgl.faa.gov/Regulatory_and_Guidance_Library/rgstc.nsf/0/A78233CBB3314BAF86257C1A0069D128?OpenDocument&Highlight=sa7753sw).
    (4) SA8918SW (http://rgl.faa.gov/Regulatory_and_Guidance_Library/rgstc.nsf/0/5FAD7ABA3EAA464C86257C1A0069F239?OpenDocument&Highlight=sa8918sw).

[[Page 3519]]



Table 1 to Paragraph (c) of This AD--Affected Airplane Models and Serial
                                 Numbers
------------------------------------------------------------------------
Cessna aircraft company airplane models         Serial Nos. (S/Ns)
------------------------------------------------------------------------
Model 500 and 501 airplanes............  0001 through 0689 inclusive.
Model 550 and 551 airplanes............  0002 through 0733 inclusive,
                                          and 0801 through 1136
                                          inclusive.
Model S550 airplanes...................  0001 through 0160 inclusive.
Model 560 airplanes....................  0001 through 0707 inclusive,
                                          and 0751 0751 through 0815
                                          inclusive.
Model 650 airplanes....................  0200 through 0241 inclusive,
                                          and 7001 7001 through 7119
                                          inclusive.
------------------------------------------------------------------------

(d) Subject

    Air Transport Association (ATA) of America 21, Air Conditioning.

(e) Unsafe Condition

    This AD was prompted by reports of smoke and/or fire in the 
tailcone caused by sparking due to excessive wear of the brushes in 
the air conditioning (A/C) motor. We are issuing this AD to prevent 
the brushes in the A/C motor from wearing down beyond their limits, 
which could result in the rivet in the brush contacting the 
commutator, causing sparks and consequent fire and/or smoke in the 
tailcone with no means to detect or extinguish the fire and/or 
smoke.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Inspection for Part Number (P/N)

    Within 30 days or 10 flight hours after the effective date of 
this AD, whichever occurs first: Inspect the A/C compressor motor to 
determine whether P/N FWA1134104-1 or P/N FWA1134104-5 is installed. 
A review of airplane maintenance records is acceptable in lieu of 
this inspection if the part number of the A/C compressor motor can 
be conclusively determined from that review.

(h) Inspection of Compressor Hour Meter and Maintenance Records

    If, during the inspection required by paragraph (g) of this AD, 
any A/C compressor motor having P/N FWA1134104-1 or P/N FWA1134104-5 
is found: Within 30 days or 10 flight hours after the effective date 
of this AD, whichever occurs first, determine the hour reading on 
the A/C compressor hour meter as specified in paragraphs (h)(1) and 
(h)(2) of this AD.
    (1) Inspect the number of hours accumulated on the A/C 
compressor hour meter.
    (2) Check the airplane logbook for any entry for replacing the 
A/C compressor motor brushes with new brushes, or for replacing the 
compressor motor or compressor condenser module assembly (pallet) 
with a motor or assembly that has new brushes.
    (i) If the logbook contains an entry for replacement of parts, 
as specified in paragraph (h)(2) of this AD, determine the number of 
hours accumulated on the A/C compressor motor brushes by comparing 
the number of hours on the compressor motor since replacement and 
use this number in lieu of the number determined in paragraph (h)(1) 
of this AD.
    (ii) If, through the logbook check, a determination cannot be 
made regarding the number of hours accumulated on the A/C compressor 
motor brushes, as specified in paragraph (h)(2) of this AD, use the 
number of hours accumulated on the A/C compressor hour meter 
determined in paragraph (h)(1) of this AD, or presume the brushes 
have over 500 hours' time-in-service.

(i) Replacement

    Using the hour reading on the A/C compressor hour meter 
determined in paragraph (h) of this AD, replace the A/C compressor 
motor brushes with new brushes at the later of the times specified 
in paragraphs (i)(1) and (i)(2) of this AD. Thereafter, repeat the 
replacement of the A/C compressor motor brushes at intervals not to 
exceed 500 hours' time-in-service on the A/C compressor motor. Do 
the replacement in accordance with the applicable Cessna maintenance 
manual subject specified in paragraphs (j)(1) through (j)(6) of this 
AD.
    (1) Before the accumulation of 500 total hours' time-in-service 
on the A/C compressor motor.
    (2) Before further flight after doing the inspection required in 
paragraph (h) of this AD.

(j) Maintenance Manual Information for Replacement

    Use the instructions in the applicable Cessna maintenance manual 
subject specified in paragraphs (j)(1) through (j)(6) of this AD to 
do the replacement required by paragraph (i) of this AD.
    (1) Subject 4-11-00, Replacement Time Limits, of Chapter 4, 
Airworthiness Limitations, Revision 6, dated June 23, 2014, of the 
Cessna Model 500/501 Maintenance Manual.
    (2) Subject 4-11-00, Replacement Time Limits, of Chapter 4, 
Airworthiness Limitations, Revision 10, dated June 23, 2014, of the 
Cessna Model 550/551 Maintenance Manual.
    (3) Subject 4-11-00, Replacement Time Limits, of Chapter 4, 
Airworthiness Limitations, Revision 12, dated June 23, 2014, of the 
Cessna Model 550 Bravo Maintenance Manual.
    (4) Subject 4-11-00, Replacement Time Limits, of Chapter 4, 
Airworthiness Limitations, Revision 9, dated June 23, 2014, of the 
Cessna Model S550 Maintenance Manual.
    (5) Subject 4-11-00, Replacement Time Limits, of Chapter 4, 
Airworthiness Limitations, Revision 22, dated June 23, 2014, of the 
Cessna Model 560 Maintenance Manual.
    (6) Subject 4-11-00, Replacement Time Limits, of Chapter 4, 
Airworthiness Limitations, Revision 32, dated June 23, 2014, of the 
Cessna Model 650 Maintenance Manual.

(k) Deactivation of the A/C System

    In lieu of replacing the A/C compressor motor brushes as 
required by this AD, deactivate the A/C system as specified in 
paragraph (k)(1) or (k)(2) of this AD, as applicable.
    (1) For all airplanes except Model 650 airplanes: Pull the vapor 
cycle A/C circuit breaker labeled ``AIR COND,'' do the actions 
specified in paragraphs (k)(1)(i) and (k)(1)(ii) of this AD, and 
document deactivation of the system in the airplane logbook, 
referring to this AD as the reason for deactivation.
    (i) Fabricate a placard that states: ``A/C DISABLED'' with \1/
8\-inch black lettering on a white background.
    (ii) Install the placard on the airplane instrument panel within 
6 inches of the A/C selection switch.
    (2) For Model 650 airplanes: Pull the vapor cycle A/C circuit 
breaker labeled ``FWD EVAP FAN,'' do the actions specified in 
paragraphs (k)(1)(i) and (k)(1)(ii) of this AD, and document 
deactivation of the system in the airplane logbook, referring to 
this AD as the reason for deactivation.
    Note 1 to paragraph (k) of this AD: While the A/C system is 
deactivated, it is recommended that airplane operators remain aware 
of the operating temperature limitations specified in the applicable 
airplane flight manual.

(l) Reactivation of the A/C System

    If the A/C system is deactivated, as specified in paragraph (k) 
of this AD, prior to the A/C system being reactivated: Perform the 
inspection specified in paragraph (h) of this AD, and do the 
replacements specified in paragraph (i) of this AD, at the times 
specified in paragraph (i) of this AD. Return the A/C system to 
service by doing the actions specified in paragraph (l)(1) or (l)(2) 
of this AD, as applicable.
    (1) For all airplanes except Model 650 airplanes: Push in the 
vapor cycle A/C circuit breaker labeled ``AIR COND,'' remove the 
placard by the A/C selection switch that states ``A/C DISABLED,'' 
and document reactivation of the system in the airplane logbook.
    (2) For Model 650 airplanes: Push in the vapor cycle A/C circuit 
breaker labeled ``FWD EVAP FAN,'' remove the placard by the A/C 
selection switch that states ``A/C DISABLED,'' and document 
reactivation of the system in the airplane logbook.

(m) Parts Return and Reporting Requirements

    For the first two A/C compressor motor brush replacement cycles 
on each airplane, send the removed brushes to Cessna Aircraft 
Company, Cessna Service Parts and

[[Page 3520]]

Programs, 7121 Southwest Boulevard, Wichita, KS 67215. Provide the 
brushes and the information specified in paragraphs (m)(1) through 
(m)(6) of this AD within 30 days after the replacement if the 
replacement was done on or after the effective date of this AD, or 
within 30 days after the effective date of this AD if the 
replacement was done before the effective date of this AD.
    (1) The model and serial number of the airplane.
    (2) The part number of the motor.
    (3) The part number of the brushes, if known.
    (4) The elapsed time, in motor hours, since the last brush/motor 
replacement, if known.
    (5) If motor hours are unknown, report the elapsed airplane 
flight hours since the last brush/motor replacement, and indicate 
that motor hours are unknown.
    (6) The number of motor hours currently displayed on the pallet 
hour meter, if installed.

(n) Parts Installation Limitation

    As of the effective date of this AD, no person may install an A/
C compressor motor having P/N FWA1134104-1 or P/N FWA1134104-5, 
unless the inspection specified in paragraph (h) of this AD is done 
before installation, and the replacements specified in paragraph (i) 
of this AD are subsequently done in accordance with the applicable 
service information identified in paragraphs (j)(1) through (j)(6) 
of this AD at the times specified in paragraph (i) of this AD.

(o) Special Flight Permit Limitation

    Special flight permits may be issued in accordance with sections 
21.197 and 21.199 of the Federal Aviation Regulations (14 CFR 21.197 
and 21.199) with the following limitation: Operation of the A/C 
system is prohibited.

(p) Paperwork Reduction Act Burden Statement

    A federal agency may not conduct or sponsor, and a person is not 
required to respond to, nor shall a person be subject to a penalty 
for failure to comply with a collection of information subject to 
the requirements of the Paperwork Reduction Act unless that 
collection of information displays a current valid OMB Control 
Number. The OMB Control Number for this information collection is 
2120-0056. Public reporting for this collection of information is 
estimated to be approximately 5 minutes per response, including the 
time for reviewing instructions, completing and reviewing the 
collection of information. All responses to this collection of 
information are mandatory. Comments concerning the accuracy of this 
burden and suggestions for reducing the burden should be directed to 
the FAA at: 800 Independence Ave. SW., Washington, DC 20591, Attn: 
Information Collection Clearance Officer, AES-200.

(q) Alternative Methods of Compliance (AMOCs)

    (1) The Manager, Wichita Aircraft Certification Office (ACO), 
FAA, has the authority to approve AMOCs for this AD, if requested 
using the procedures found in 14 CFR 39.19. In accordance with 14 
CFR 39.19, send your request to your principal inspector or local 
Flight Standards District Office, as appropriate. If sending 
information directly to the manager of the ACO, send it to the 
attention of the person identified in paragraph (r)(1) of this AD.
    (2) Before using any approved AMOC, notify your appropriate 
principal inspector, or lacking a principal inspector, the manager 
of the local flight standards district office/certificate holding 
district office.

(r) Related Information

    (1) For more information about this AD, contact Craig 
Henrichsen, Aerospace Engineer, Electrical Systems and Avionics 
Branch, ACE-119W, FAA, Wichita Aircraft Certification Office (ACO), 
1801 Airport Road, Room 100, Mid-Continent Airport, Wichita, KS 
67209; phone: 316 946 4110; fax: 316 946 4107; email: 
Craig.Henrichsen@faa.gov.
    (2) For service information identified in this AD, contact 
Cessna Aircraft Co., P.O. Box 7706, Wichita, KS 67277; telephone 
316-517-6215; fax 316-517-5802; email 
citationpubs@cessna.textron.com; Internet https://www.cessnasupport.com/newlogin.html. You may view this referenced 
service information at the FAA, Transport Airplane Directorate, 1601 
Lind Avenue SW., Renton, WA. For information on the availability of 
this material at the FAA, call 425-227-1221.

    Issued in Renton, Washington, on January 11, 2015.
Jeffrey E. Duven,
Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2015-00994 Filed 1-22-15; 8:45 am]
BILLING CODE 4910-13-P


