
[Federal Register Volume 79, Number 157 (Thursday, August 14, 2014)]
[Proposed Rules]
[Pages 47594-47597]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: 2014-19244]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2014-0567; Directorate Identifier 2014-NM-124-AD]
RIN 2120-AA64


Airworthiness Directives; Bombardier, Inc. Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to adopt a new airworthiness directive (AD) for 
certain Bombardier, Inc. Model CL-600-2B19 (Regional Jet Series 100 & 
440) airplanes. This proposed AD was prompted by issuance of revised 
certification maintenance requirements (CMR) for the horizontal 
stabilizer trim actuator (HSTA). This proposed AD would require 
revising the maintenance or inspection program. We are proposing this 
AD to detect and correct premature wear and cracking of the HSTAs, 
which could result in reduced structural integrity and reduced control 
of the airplane due to the failure of system components.

DATES: We must receive comments on this proposed AD by September 29, 
2014.

ADDRESSES: You may send comments, using the procedures found in 14 CFR

[[Page 47595]]

11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC 20590.
     Hand Delivery: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC, between 9 a.m. and 5 p.m., Monday 
through Friday, except Federal holidays.
    For service information identified in this proposed AD, contact 
Bombardier, Inc., 400 C[ocirc]te-Vertu Road West, Dorval, Qu[eacute]bec 
H4S 1Y9, Canada; telephone 514-855-5000; fax 514-855-7401; email 
thd.crj@aero.bombardier.com; Internet http://www.bombardier.com. You 
may view this referenced service information at the FAA, Transport 
Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For information 
on the availability of this material at the FAA, call 425-227-1221.

Examining the AD Docket

    You may examine the AD docket on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2014-
0567; or in person at the Docket Management Facility between 9 a.m. and 
5 p.m., Monday through Friday, except Federal holidays. The AD docket 
contains this proposed AD, the regulatory evaluation, any comments 
received, and other information. The street address for the Docket 
Operations office (telephone 800-647-5527) is in the ADDRESSES section. 
Comments will be available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Cesar Gomez, Aerospace Engineer, 
Airframe and Mechanical Systems Branch, ANE-171, FAA, New York Aircraft 
Certification Office, 1600 Stewart Avenue, Suite 410, Westbury, New 
York 11590; telephone (516) 228-7318; fax (516) 794-5531.

SUPPLEMENTARY INFORMATION:

Comments Invited

    We invite you to send any written relevant data, views, or 
arguments about this proposed AD. Send your comments to an address 
listed under the ADDRESSES section. Include ``Docket No. FAA-2014-0567; 
Directorate Identifier 2014-NM-124-AD'' at the beginning of your 
comments. We specifically invite comments on the overall regulatory, 
economic, environmental, and energy aspects of this proposed AD. We 
will consider all comments received by the closing date and may amend 
this proposed AD based on those comments.
    We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this proposed AD.

Discussion

    Transport Canada Civil Aviation (TCCA), which is the aviation 
authority for Canada, has issued Canadian Airworthiness Directive CF-
2014-13, dated April 17, 2014 (referred to after this as the Mandatory 
Continuing Airworthiness Information, or ``the MCAI''), to correct an 
unsafe condition for certain Bombardier, Inc. Model CL-600-2B19 
(Regional Jet Series 100 & 440) airplanes. The MCAI states:

    A revision has been made to Part 2 of the Canadair Regional Jet 
Maintenance Requirements Manual (MRM), Appendix A--Certification 
Maintenance Requirements which introduces a new task for the HSTA. 
Failure to comply with the CMR task could lead to an unsafe 
condition.
    This [Canadian] AD is issued to ensure that premature wear and 
cracking of the affected components are detected and corrected. 
[This condition could result in reduced structural integrity and 
reduced control of the airplane due to the failure of system 
components.]

    You may examine the MCAI in the AD docket on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2014-
0567.

Relevant Service Information

    Bombardier has issued Temporary Revision 2A-58, dated January 31, 
2014, to Appendix A--Certification Maintenance Requirements, of Part 2, 
of Bombardier CL-600-2B19 Maintenance Requirements Manual. The actions 
described in this service information are intended to correct the 
unsafe condition identified in the MCAI.

FAA's Determination and Requirements of This Proposed AD

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to our bilateral agreement with the State of Design Authority, we have 
been notified of the unsafe condition described in the MCAI and service 
information referenced above. We are proposing this AD because we 
evaluated all pertinent information and determined an unsafe condition 
exists and is likely to exist or develop on other products of the same 
type design.

``Contacting the Manufacturer'' Paragraph in This Proposed AD

    Since late 2006, we have included a standard paragraph titled 
``Airworthy Product'' in all MCAI ADs in which the FAA develops an AD 
based on a foreign authority's AD.
    The MCAI or referenced service information in an FAA AD often 
directs the owner/operator to contact the manufacturer for corrective 
actions, such as a repair. Briefly, the Airworthy Product paragraph 
allowed owners/operators to use corrective actions provided by the 
manufacturer if those actions were FAA-approved. In addition, the 
paragraph stated that any actions approved by the State of Design 
Authority (or its delegated agent) are considered to be FAA-approved.
    In an NPRM having Directorate Identifier 2012-NM-101-AD (78 FR 
78285, December 26, 2013), we proposed to prevent the use of repairs 
that were not specifically developed to correct the unsafe condition, 
by requiring that the repair approval provided by the State of Design 
Authority or its delegated agent specifically refer to the FAA AD. This 
change was intended to clarify the method of compliance and to provide 
operators with better visibility of repairs that are specifically 
developed and approved to correct the unsafe condition. In addition, we 
proposed to change the phrase ``its delegated agent'' to include a 
design approval holder (DAH) with State of Design Authority design 
organization approval (DOA), as applicable, to refer to a DAH 
authorized to approve required repairs for the proposed AD.
    One commenter to the NPRM having Directorate Identifier 2012-NM-
101-AD (78 FR 78285, December 26, 2013) stated the following: ``The 
proposed wording, being specific to repairs, eliminates the 
interpretation that Airbus messages are acceptable for approving minor 
deviations (corrective actions) needed during accomplishment of an AD 
mandated Airbus service bulletin.''
    This comment has made the FAA aware that some operators have 
misunderstood or misinterpreted the Airworthy Product paragraph to 
allow the owner/operator to use messages provided by the manufacturer 
as approval of deviations during the accomplishment of an AD-mandated 
action. The Airworthy Product paragraph does not approve messages or 
other information provided by the manufacturer for deviations to the

[[Page 47596]]

requirements of the AD-mandated actions. The Airworthy Product 
paragraph only addresses the requirement to contact the manufacturer 
for corrective actions for the identified unsafe condition and does not 
cover deviations from other AD requirements. However, deviations to AD-
required actions are addressed in 14 CFR 39.17, and anyone may request 
the approval for an alternative method of compliance to the AD-required 
actions using the procedures found in 14 CFR 39.19.
    To address this misunderstanding and misinterpretation of the 
Airworthy Product paragraph, we have changed the paragraph and retitled 
it ``Contacting the Manufacturer.'' This paragraph now clarifies that 
for any requirement in this proposed AD to obtain corrective actions 
from a manufacturer, the actions must be accomplished using a method 
approved by the FAA, TCCA, or Bombardier, Inc.'s TCCA Design Approval 
Organization (DAO).
    The Contacting the Manufacturer paragraph also clarifies that, if 
approved by the DAO, the approval must include the DAO-authorized 
signature. The DAO signature indicates that the data and information 
contained in the document are TCCA-approved, which is also FAA-
approved. Messages and other information provided by the manufacturer 
that do not contain the DAO-authorized signature approval are not TCCA-
approved, unless TCCA directly approves the manufacturer's message or 
other information.
    This clarification does not remove flexibility previously afforded 
by the Airworthy Product paragraph. Consistent with long-standing FAA 
policy, such flexibility was never intended for required actions. This 
is also consistent with the recommendation of the Airworthiness 
Directive Implementation Aviation Rulemaking Committee to increase 
flexibility in complying with ADs by identifying those actions in 
manufacturers' service instructions that are ``Required for 
Compliance'' with ADs. We continue to work with manufacturers to 
implement this recommendation. But once we determine that an action is 
required, any deviation from the requirement must be approved as an 
alternative method of compliance.
    We also have decided not to include a generic reference to either 
the ``delegated agent'' or ``design approval holder (DAH) with State of 
Design Authority design organization approval,'' but instead we have 
provided the specific delegation approval granted by the State of 
Design Authority for the DAH throughout this proposed AD.

Costs of Compliance

    We estimate that this proposed AD affects 416 airplanes of U.S. 
registry.
    We also estimate that it would take about 1 work-hour per product 
to comply with the basic requirements of this proposed AD. The average 
labor rate is $85 per work-hour. Required parts would cost about $0 per 
product. Based on these figures, we estimate the cost of this proposed 
AD on U.S. operators to be $35,360, or $85 per product.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more detail the scope of the Agency's 
authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979);
    3. Will not affect intrastate aviation in Alaska; and
    4. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

Bombardier, Inc.: Docket No. FAA-2014-0567; Directorate Identifier 
2014-NM-124-AD.

(a) Comments Due Date

    We must receive comments by September 29, 2014.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Bombardier, Inc. Model CL-600-2B19 (Regional 
Jet Series 100 & 440) airplanes, certificated in any category, 
equipped with horizontal stabilizer trim actuator (HSTA) part number 
(P/N) 601R92305-7 (vendor P/N 8396-5).

(d) Subject

    Air Transport Association (ATA) of America Code 55, Stabilizers.

(e) Reason

    This AD was prompted by issuance of revised certification 
maintenance requirements (CMR) for the horizontal stabilizer trim 
actuator (HSTA). We are issuing this AD to detect and correct 
premature wear and cracking of certain HSTAs, which could result in 
reduced structural integrity and reduced control of the airplane due 
to the failure of system components.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Maintenance or Inspection Program Revision

    Within 30 days after the effective date of this AD, revise the 
maintenance or inspection program, as applicable, to incorporate the 
information specified in Task C27-40-103-05 of Bombardier Temporary 
Revision (TR) 2A-58, dated January 31, 2014, into Appendix A--CMR, 
of Part 2, of Bombardier CL-600-2B19 MRM. The initial compliance 
time for accomplishing CMR Task C27-40-103-05 is at the applicable 
phase-in time

[[Page 47597]]

specified in Bombardier TR 2A-58, dated January 31, 2014, or within 
30 days after the effective date of this AD, whichever occurs later. 
The revision required by paragraph (g) of this AD may be done by 
inserting a copy of Bombardier TR 2A-58, dated January 31, 2014, 
into Appendix A--CMR, of Part 2, of Bombardier CL-600-2B19 MRM. When 
TR 2A-58, dated January 31, 2014, has been included in general 
revisions of the MRM, the general revisions may be inserted in the 
MRM, provided the relevant information in the general revision is 
identical to that in TR 2A-58, dated January 31, 2014.

(h) No Alternative Actions and Intervals

    After accomplishing the revision required by paragraph (g) of 
this AD, no alternative actions (e.g., inspections) or intervals may 
be used unless the actions or intervals are approved as an 
alternative method of compliance (AMOC) in accordance with the 
procedures specified in paragraph (i)(1) of this AD.

(i) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, New 
York Aircraft Certification Office (ACO), ANE-170, FAA, has the 
authority to approve AMOCs for this AD, if requested using the 
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, 
send your request to your principal inspector or local Flight 
Standards District Office, as appropriate. If sending information 
directly to the ACO, send it to Program Manager, Continuing 
Operational Safety, FAA, New York ACO, 1600 Stewart Avenue, Suite 
410, Westbury, NY 11590; telephone (516) 228-7300; fax (516) 794-
5531. Before using any approved AMOC, notify your appropriate 
principal inspector, or lacking a principal inspector, the manager 
of the local flight standards district office/certificate holding 
district office. The AMOC approval letter must specifically 
reference this AD.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain corrective actions from a manufacturer, the action must be 
accomplished using a method approved by the Manager, New York ACO, 
ANE-170, Engine and Propeller Directorate, FAA; or Transport Canada 
Civil Aviation (TCCA); or Bombardier, Inc.'s TCCA Design Approval 
Organization (DAO). If approved by the DAO, the approval must 
include the DAO-authorized signature.

(j) Related Information

    (1) Refer to Mandatory Continuing Airworthiness Information 
(MCAI) Canadian Airworthiness Directive CF-2014-13, dated April 17, 
2014, for related information. This MCAI may be found in the AD 
docket on the Internet at http://www.regulations.gov by searching 
for and locating Docket No. FAA-2014-0567.
    (2) For service information identified in this AD, contact 
Bombardier, Inc., 400 C[ocirc]te-Vertu Road West, Dorval, 
Qu[eacute]bec H4S 1Y9, Canada; telephone 514-855-5000; fax 514-855-
7401; email thd.crj@aero.bombardier.com; Internet http://www.bombardier.com. You may view this service information at the 
FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, 
WA. For information on the availability of this material at the FAA, 
call 425-227-1221.

    Issued in Renton, Washington, on August 7, 2014.
Victor Wicklund,
Acting Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2014-19244 Filed 8-13-14; 8:45 am]
BILLING CODE 4910-13-P


