
[Federal Register Volume 81, Number 120 (Wednesday, June 22, 2016)]
[Rules and Regulations]
[Pages 40492-40495]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2016-14467]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2014-0105; Directorate Identifier 2008-SW-58-AD; 
Amendment 39-18562; AD 2016-12-13]
RIN 2120-AA64


Airworthiness Directives; Airbus Helicopters (Previously 
Eurocopter France) Helicopters

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: We are superseding Airworthiness Directive (AD) 2000-05-17 and 
AD 2001-04-12, which apply to Eurocopter France (now Airbus 
Helicopters) Model EC120B helicopters. AD 2000-05-17 and AD 2001-04-12 
required repetitive visual checks of the engine-to-main gearbox (MGB) 
coupling tube assembly (coupling tube) for a crack and replacing any 
cracked tube with an airworthy tube. This new AD requires removing 
certain engine mount parts from service, measuring the height of the 
engine mounting base for certain helicopters, replacing the engine 
mount if a certain height is exceeded, inspecting the flared coupling 
on certain helicopters for a crack, and replacing the coupling if it is 
cracked. Since we issued AD 2000-05-17 and AD 2001-04-12, there have 
been reports of additional cracks in coupling tubes. These actions are 
intended to prevent coupling tube failure, loss of engine drive, and a 
subsequent forced landing of the helicopter.

DATES: This AD is effective July 27, 2016.
    The Director of the Federal Register approved the incorporation by 
reference of certain publications listed in this AD as of July 27, 
2016.

ADDRESSES: For service information identified in this final rule, 
contact Airbus Helicopters, 2701 N. Forum Drive, Grand Prairie, TX 
75052; telephone (972) 641-0000 or (800) 232-0323; fax (972) 641-3775; 
or at http://www.airbushelicopters.com/techpub. You may view this 
referenced service information at the FAA, Office of the Regional 
Counsel, Southwest Region, 10101 Hillwood Pkwy., Room 6N-321, Fort 
Worth, TX 76177. It is also available on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2014-
0105.

[[Page 40493]]

Examining the AD Docket

    You may examine the AD docket on the Internet at http://www.regulations.gov in Docket No. FAA-2014-0105; or in person at the 
Docket Management Facility between 9 a.m. and 5 p.m., Monday through 
Friday, except Federal holidays. The AD docket contains this AD, the 
Direction Generale de L'Aviation Civile (DGAC) AD, any incorporated-by-
reference information, the economic evaluation, any comments received, 
and other information. The address for the Docket Office (phone: 800-
647-5527) is Document Management Facility, U.S. Department of 
Transportation, Docket Operations, M-30, West Building Ground Floor, 
Room W12-140, 1200 New Jersey Avenue SE., Washington, DC 20590.

FOR FURTHER INFORMATION CONTACT: James Blyn, Aviation Safety Engineer, 
Regulations and Policy Group, Rotorcraft Directorate, FAA, 10101 
Hillwood Pkwy., Fort Worth, TX 76177; telephone (817) 222-5110; email 
james.blyn@faa.gov.

SUPPLEMENTARY INFORMATION:

Discussion

    On May 29, 2015, we issued a notice of proposed rulemaking (NPRM) 
to amend 14 CFR part 39 to remove AD 2000-05-17 (65 FR 13875, March 15, 
2000) and AD 2001-04-12 (66 FR 13232, March 5, 2001) and add a new AD. 
AD 2000-05-17 applied to Model EC120B helicopters with engine coupling 
tube part number (P/N) C631A1002101 and required recurring inspections 
of each coupling tube for a crack and replacing any cracked coupling 
tube with a reinforced coupling tube P/N C631A1101101. AD 2001-04-12 
applied to Model EC120B helicopters with engine coupling tube P/N 
C631A1101101 and required repetitive visual checks of each coupling 
tube for a crack. AD 2000-05-17 and AD 2001-04-12 were prompted by 
reports of cracks on the reinforced coupling tube and were intended to 
prevent coupling tube failure, loss of engine drive, and a subsequent 
forced landing.
    The NPRM published in the Federal Register on June 16, 2015 (80 FR 
34335). The NPRM was prompted by reports of additional cracks in 
coupling tubes. Eurocopter France (now Airbus Helicopters) determined 
that the washer-type engine mount may, in certain cases, induce 
excessive loading on the coupling tube, which results in binding that 
increases component wear of the inner diameter of the mounting base. 
Because of this, the DGAC, on behalf of the European Aviation Safety 
Agency (EASA), issued AD No. F-2003-325 R1, dated May 12, 2004, for 
Model EC120B helicopters with engine coupling tube, P/N C631A1101101, 
and with an engine mount containing certain parts listed in Eurocopter 
Alert Service Bulletin (ASB) No. 04A005, dated July 16, 2003. DGAC AD 
No. F-2003-325 R1 requires inspections for helicopters with an engine 
mount block modified in accordance with Eurocopter Service Bulletin 
(SB) No. 71-003, Revision 1, dated July 18, 2002; replacing any 
coupling tube that has a crack; and increasing the life limit of the 
coupling tube from 1,000 flight hours to 20,000 flight hours. Also, 
DGAC AD No. F-2003-325 R1 requires, for helicopters with a new spring-
loaded engine suspension modification in accordance with Eurocopter SB 
No. 71-005, Revision 0, dated May 14, 2004, increasing the life limit 
of the coupling tube to 20,000 flight hours and canceling the 
repetitive inspections of the coupling tube.
    The NPRM proposed to require, for helicopters with certain engine 
mounts, before further flight, removing from service certain engine 
mount parts and measuring the height of the engine mounting base. If 
the height is more than 10.5 millimeters, the NPRM proposed replacing 
the engine mount with an engine mount that does not have the affected 
parts. For certain other helicopters, the NPRM proposed to require 
within 25 hours time-in-serice (TIS) replacing the spring-type engine 
suspension system, dye-penetrant inspecting the flared coupling for a 
crack, and replacing any cracked flared coupling. The NPRM also 
proposed removing coupling tube P/N C631A1002101 from service and 
prohibiting installation of that coupling tube on any helicopter.
    Since the NPRM was issued, the FAA Southwest Regional Office has 
relocated and a group email address has been established for requesting 
an FAA alternative method of compliance for a helicopter of foreign 
design. We have revised the contact information throughout this final 
rule to reflect the new address and new email address.

Comments

    After our NPRM (80 FR 34335, June 16, 2015) was published, we 
received comments from one commenter.

Request

    Airbus Helicopters disagrees with the proposed requirement to 
replace the spring-type engine suspension system in accordance with 
Eurocopter SB No. 71-005 for helicopters with an improved engine mount 
under Eurocopter SB No. 71-003. Airbus Helicopters states there have 
been no coupling tube failures since incorporation of Eurocopter SB No. 
71-003, and therefore the proposed requirement would not increase 
safety levels.
    We disagree. Installing the improved engine mount specified in 
Eurocopter SB No. 71-003 extends the compliance time for a recurring 
visual inspection of the coupling tube from 5 hours TIS to 25 hours 
TIS. When issued, that recurring inspection was considered a short-term 
interim action until an effective modification or action was developed, 
approved, and available. Eurocopter SB No. 71-005 contained such an 
effective action to cancel that interim action and was developed and 
approved in May 2004.
    Airbus Helicopters requested that, if we mandate the proposed 
requirement to replace the spring-type engine suspension system in 
accordance with Eurocopter SB No. 71-005, we change the proposed 
compliance time from 25 hours TIS to 18 months to allow for 
availability of parts.
    We disagree. Eurocopter SB No. 71-005 was approved May 13, 2004. 
The NPRM was published June 16, 2015. The substantial amount of time 
that has passed since the approval of the service information and 
publication of our NPRM provided operators with enough notice of our 
proposal to mandate that procedure such that availability of parts 
should not be an issue.

FAA's Determination

    This helicopter has been approved by the aviation authority of 
France and is approved for operation in the United States. Pursuant to 
our bilateral agreement with France, the DGAC on behalf of EASA, has 
kept the FAA informed of the situation described above. We are issuing 
this AD because we evaluated all information provided by the DGAC, 
reviewed the relevant information, considered the comments received, 
and determined the unsafe condition exists and is likely to exist or 
develop on other helicopters of this same type design and that air 
safety and the public interest require adopting the AD requirements as 
proposed.

Related Service Information Under 1 CFR Part 51

    Eurocopter issued ASB No. 04A005, Revision 0, dated July 16, 2003, 
which prohibits, after June 30, 2004, operating an engine mount made up 
of the following parts: Support arm, P/N C714A1107201; swaged support 
arm, P/N C714A1106201; left-hand support bracket, P/N C714A1101102; and 
right-

[[Page 40494]]

hand support bracket, P/N C714A1101103. ASB No. 04A005 also specifies 
measuring the height of the engine mounting base and, if the height is 
more than 10.5 millimeters, replacing the engine mount with an engine 
mount that does not have the specified P/N. ASB No. 04A005 does not 
apply to helicopters modified with an improved engine mount in 
accordance with SB No. 71-003. ASB No. 04A005 also does not apply to 
helicopters with a serial number 1170 or larger, as the specified 
engine mounts are not installed on those helicopters.
    Eurocopter also issued SB No. 71-005, Revision 0, dated May 14, 
2004, which contains procedures to modify the spring-type engine 
suspension system and dye-penetrant inspect the flared coupling 
assembly.
    This service information is reasonably available because the 
interested parties have access to it through their normal course of 
business or by the means identified in the ADDRESSES section.

Other Related Service Information

    Eurocopter issued SB No. 71-003, Revision 1, dated July 18, 2002, 
which contains procedures to improve the engine mount. Eurocopter also 
issued ASB No. 05A003, Revision 2, dated July 16, 2003, for helicopters 
that have not been modified with an improved engine mount in accordance 
with SB No. 71-003, which specifies inspecting the coupling tube for a 
crack every 5 hours and establishing a coupling tube life limit of 
1,000 hours. For helicopters that have been modified with an improved 
engine mount, ASB No. 05A003 specifies inspecting the coupling tube for 
a crack every 25 hours and increasing the coupling tube life limit to 
20,000 hours. ASB No. 05A003 was revised to Revision 3, dated May 11, 
2004, to specify an optional spring-type engine suspension modification 
and cancel the repetitive inspection for this modified configuration.

Differences Between This AD and the DGAC AD

    This AD requires the installation of the spring-type engine 
suspension modification specified in Eurocopter SB No. 71-005 and does 
not require the repetitive inspection of the coupling tube and the 
engine mount base. This AD also does not require you to contact the 
manufacturer.

Costs of Compliance

    We estimate that this AD will affect 23 helicopters of the 115 
helicopters of U.S. Registry. At an average labor rate of $85 per work-
hour, we estimate that operators may incur the following costs in order 
to comply with this AD.
    Installing new mounting arms and brackets requires about 12 work-
hours and required parts cost $9,194, for a total cost per helicopter 
of $10,214 and $234,922 for the U.S. fleet. Installing the mounting 
spring kit requires about 14 work-hours and required parts cost 
$14,621, for a total cost per helicopter of $15,811 and $363,653 for 
the U.S. fleet. Dye-penetrant inspecting the coupling tube requires 
about 1 work-hour for a cost per helicopter of $85 and $1,955 for the 
U.S. fleet.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, Section 106, describes the 
authority of the FAA Administrator. Subtitle VII, Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701, ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We have determined that this AD will not have federalism 
implications under Executive Order 13132. This AD will not have a 
substantial direct effect on the States, on the relationship between 
the national government and the States, or on the distribution of power 
and responsibilities among the various levels of government.
    For the reasons discussed above, I certify that this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Is not a ``significant rule'' under DOT Regulatory Policies and 
Procedures (44 FR 11034, February 26, 1979),
    (3) Will not affect intrastate aviation in Alaska to the extent 
that a regulatory, and
    (4) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by:
0
a. Removing Airworthiness Directive (AD) 2000-05-17, Amendment 39-11627 
(65 FR 13875, March 15, 2000); and AD 2001-04-12, Amendment 39-12131 
(66 FR 13232, March 5, 2001); and
0
b. Adding the following new AD:

2016-12-13 Airbus Helicopters (Previously Eurocopter France): 
Amendment 39-18562; Docket No. FAA-2014-0105; Directorate Identifier 
2008-SW-58-AD.

(a) Applicability

    This AD applies to Model EC120B helicopters with an engine-to-
main gearbox coupling tube assembly (coupling tube), part number (P/
N) C631A1101101 or P/N C631A1002101, installed, certificated in any 
category.

(b) Unsafe Condition

    This AD defines the unsafe condition as a crack in a coupling 
tube. This condition could result in coupling tube failure, loss of 
engine drive, and a subsequent forced landing of the helicopter.

(c) Affected ADs

    This AD supersedes AD 2000-05-17, Amendment 39-11627 (65 FR 
13875, March 15, 2000) and AD 2001-04-12, Amendment 39-12131 (66 FR 
13232, March 5, 2001).

(d) Effective Date

    This AD becomes effective July 27, 2016.

(e) Compliance

    You are responsible for performing each action required by this 
AD within the specified compliance time unless it has already been 
accomplished prior to that time.

(f) Required Actions

    (1) For helicopters with a serial number up to and including 
1169, not modified with an improvement of the engine mount in 
accordance with Eurocopter Service Bulletin (SB) No. 71-003, 
Revision 1, dated July 18, 2002 (SB 71-003), or not modified by 
installing a spring-type engine suspension system in accordance with 
Eurocopter SB No. 71-005, Revision 0, dated May 14, 2004 (SB 71-
005), before further flight:

[[Page 40495]]

    (i) Remove from service the following engine mount parts:
    (A) Support arm, P/N C714A1107201;
    (B) Swaged support arm, P/N C714A1106201;
    (C) Left-hand support bracket, P/N C714A1101102; and
    (D) Right-hand support bracket, P/N C714A1101103.
    (ii) Measure the height of the engine mounting base as depicted 
in Figure 1 of Eurocopter Alert SB No. 04A005, Revision 0, dated 
July 16, 2003. If the height is more than 10.5 millimeters, replace 
the engine mount with an engine mount that does not have the parts 
identified in paragraph (f)(1)(i) of this AD.
    (2) For helicopters with a serial number 1170 and larger or 
helicopters modified with an improvement of the engine mount in 
accordance with SB 71-003:
    (i) Within 25 hours TIS, replace the spring-type engine 
suspension system and perform a dye-penetrant inspection of the 
flared coupling for a crack by following the Accomplishment 
Instructions, paragraphs 2.B.2.a through 2.B.2.c of SB 71-005.
    (ii) If there is a crack in the flared coupling, before further 
flight, replace the coupling with an airworthy coupling.
    (3) For helicopters with coupling tube, P/N C631A1002101, 
installed, before further flight, remove coupling tube, P/N 
C631A1002101, from service. Do not install coupling tube, P/N 
C631A1002101, on any helicopter.

(g) Special Flight Permits

    Special flight permits may be issued provided there are no 
cracks in the coupling tube attachment fitting.

(h) Alternative Methods of Compliance (AMOCs)

    (1) The Manager, Safety Management Group, FAA, may approve AMOCs 
for this AD. Send your proposal to: James Blyn, Aviation Safety 
Engineer, Regulations and Policy Group, Rotorcraft Directorate, FAA, 
10101 Hillwood Pkwy., Fort Worth, TX 76177; telephone (817) 222-
5110; email 9-ASW-FTW-AMOC-Requests@faa.gov.
    (2) For operations conducted under a 14 CFR part 119 operating 
certificate or under 14 CFR part 91, subpart K, we suggest that you 
notify your principal inspector, or lacking a principal inspector, 
the manager of the local flight standards district office or 
certificate holding district office, before operating any aircraft 
complying with this AD through an AMOC.

(i) Additional Information

    (1) Eurocopter Alert Service Bulletin (ASB) No. 05A003, Revision 
2, dated July 16, 2003; Eurocopter ASB No. 05A003, Revision 3, dated 
May 11, 2004; and Eurocopter Service Bulletin No. 71-003, Revision 
1, dated July 18, 2002; which are not incorporated by reference, 
contain additional information about the subject of this final rule. 
For Eurocopter service information identified in this final rule, 
contact Airbus Helicopters, 2701 N. Forum Drive, Grand Prairie, TX 
75052; telephone (972) 641-0000 or (800) 232-0323; fax (972) 641-
3775; or at http://www.airbushelicopters.com/techpub. You may review 
a copy of the service information at the FAA, Office of the Regional 
Counsel, Southwest Region, 10101 Hillwood Pkwy., Room 6N-321, Fort 
Worth, TX 76177.
    (2) The subject of this AD is addressed in Direction Generale de 
L'Aviation Civile (DGAC) AD No. F-2003-325 R1, Revision 1, dated May 
12, 2004. You may view the DGAC AD on the Internet at http://www.regulations.gov in Docket No. FAA-2014-0105.

(j) Subject

    Joint Aircraft Service Component (JASC) Code: 6310, Engine/
Transmission Coupling--Coupling Tube, Engine Mount, and Engine Mount 
Base.

(k) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference of the service information listed in this 
paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless the AD specifies otherwise.
    (i) Eurocopter Alert Service Bulletin No. 04A005, Revision 0, 
dated July 16, 2003.
    (ii) Eurocopter Service Bulletin No. 71-005, Revision 0, dated 
May 14, 2004.
    (3) For Eurocopter service information identified in this final 
rule, contact Airbus Helicopters, 2701 N. Forum Drive, Grand 
Prairie, TX 75052; telephone (972) 641-0000 or (800) 232-0323; fax 
(972) 641-3775; or at http://www.airbushelicopters.com/techpub.
    (4) You may view this service information at FAA, Office of the 
Regional Counsel, Southwest Region, 10101 Hillwood Pkwy., Room 6N-
321, Fort Worth, TX 76177. For information on the availability of 
this material at the FAA, call (817) 222-5110.
    (5) You may view this service information that is incorporated 
by reference at the National Archives and Records Administration 
(NARA). For information on the availability of this material at 
NARA, call (202) 741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued in Fort Worth, Texas, on June 9, 2016.
Scott A. Horn,
Acting Manager, Rotorcraft Directorate, Aircraft Certification Service.
[FR Doc. 2016-14467 Filed 6-21-16; 8:45 am]
 BILLING CODE 4910-13-P


