
[Federal Register Volume 79, Number 22 (Monday, February 3, 2014)]
[Proposed Rules]
[Pages 6102-6103]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: 2014-02158]


 ========================================================================
 Proposed Rules
                                                 Federal Register
 ________________________________________________________________________
 
 This section of the FEDERAL REGISTER contains notices to the public of 
 the proposed issuance of rules and regulations. The purpose of these 
 notices is to give interested persons an opportunity to participate in 
 the rule making prior to the adoption of the final rules.
 
 ========================================================================
 

  Federal Register / Vol. 79, No. 22 / Monday, February 3, 2014 / 
Proposed Rules  

[[Page 6102]]



DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2014-0005; Directorate Identifier 2013-NM-144-AD]
RIN 2120-AA64


Airworthiness Directives; Airbus Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to adopt a new airworthiness directive (AD) for 
certain Airbus Model A310 series airplanes. This proposed AD was 
prompted by a report of an electrical arc and a hydraulic haze in the 
wheel bay of the left-hand main landing gear (MLG), possibly resulting 
from chafing between a hydraulic high pressure hose and electrical 
wiring of the green electrical motor pump (EMP). This proposed AD would 
require modification of the electrical routing and replacement of the 
union elbows. We are proposing this AD to prevent chafing of hydraulic 
pressure hoses and electrical wiring of the green EMPs, which, in 
combination with a system failure, could cause an uncontrolled and 
undetected fire in the MLG bay.

DATES: We must receive comments on this proposed AD by March 20, 2014.

ADDRESSES: You may send comments by any of the following methods:
     Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: (202) 493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    For service information identified in this proposed AD, contact 
Airbus SAS, Airworthiness Office--EAW, 1 Rond Point Maurice Bellonte, 
31707 Blagnac Cedex, France; telephone +33 5 61 93 36 96; fax +33 5 61 
93 44 51; email account.airworth-eas@airbus.com; Internet http://www.airbus.com. You may view this referenced service information at the 
FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, 
Washington. For information on the availability of this material at the 
FAA, call 425-227-1221.

Examining the AD Docket

    You may examine the AD docket on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2014-
0005; or in person at the Docket Management Facility between 9 a.m. and 
5 p.m., Monday through Friday, except Federal holidays. The AD docket 
contains this proposed AD, the regulatory evaluation, any comments 
received, and other information. The street address for the Docket 
Operations office (telephone (800) 647-5527) is in the ADDRESSES 
section. Comments will be available in the AD docket shortly after 
receipt.

FOR FURTHER INFORMATION CONTACT: Dan Rodina, Aerospace Engineer, 
International Branch, ANM-116, Transport Airplane Directorate, FAA, 
1601 Lind Avenue SW., Renton, WA 98057-3356; telephone (425) 227-2125; 
fax (425) 227-1149.

SUPPLEMENTARY INFORMATION:

Comments Invited

    We invite you to send any written relevant data, views, or 
arguments about this proposed AD. Send your comments to an address 
listed under the ADDRESSES section. Include ``Docket No. FAA-2014-0005; 
Directorate Identifier 2013-NM-144-AD'' at the beginning of your 
comments. We specifically invite comments on the overall regulatory, 
economic, environmental, and energy aspects of this proposed AD. We 
will consider all comments received by the closing date and may amend 
this proposed AD based on those comments.
    We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this proposed AD.

Discussion

    The European Aviation Safety Agency (EASA), which is the Technical 
Agent for the Member States of the European Community, has issued EASA 
Airworthiness Directive 2013-0165, dated July 25, 2013 (referred to 
after this as the Mandatory Continuing Airworthiness Information, or 
``the MCAI''), to correct an unsafe condition for the specified 
products. The MCAI states:

    An A310 operator reported an electrical arc and a large 
hydraulic haze in the Left Hand (LH) Main Landing Gear (MLG) wheel 
bay that occurred during ground operation.
    The analysis of the occurrence revealed that this was likely 
caused by chafing between a hydraulic high pressure hose and 
electrical wiring of the Green Electrical Motor Pump (EMP).
    This condition, * * * could result in an undetected and 
uncontrolled fire in the LH MLG wheel bay.
    For the reason described above, this [EASA] AD requires 
modification of the electrical routing and installation of 
reinforced hydraulic pipes [by replacing the union elbows to re-
route the delivery pipe at the upper EMP].

You may examine the MCAI in the AD docket on the Internet at http://www.regulations.gov by searching for and locating it in Docket No. 
FAA[dash]2014[dash]0005.

Relevant Service Information

    Airbus has issued Mandatory Service Bulletin A310-29-2103, dated 
December 21, 2012. The actions described in this service information 
are intended to correct the unsafe condition identified in the MCAI.

FAA's Determination and Requirements of This Proposed AD

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to our bilateral agreement with the State of Design Authority, we have 
been notified of the unsafe condition described in the MCAI and service 
information referenced above. We are proposing this AD because we 
evaluated all pertinent information and determined an unsafe condition 
exists and is likely to exist or develop on other products of the same 
type design.

[[Page 6103]]

Costs of Compliance

    We estimate that this proposed AD affects 36 airplanes of U.S. 
registry.
    We also estimate that it would take about 4 work-hours per product 
to comply with the basic requirements of this proposed AD. The average 
labor rate is $85 per work-hour. Required parts would cost about $1,170 
per product. Based on these figures, we estimate the cost of this 
proposed AD on U.S. operators to be 54,360, or $1,510 per product.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more detail the scope of the Agency's 
authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This proposed regulation is 
within the scope of that authority because it addresses an unsafe 
condition that is likely to exist or develop on products identified in 
this rulemaking action.

Regulatory Findings

    We determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979);
    3. Will not affect intrastate aviation in Alaska; and
    4. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new AD:

Airbus: Docket No. FAA-2014-0005; Directorate Identifier 2013-NM-
144-AD.

(a) Comments Due Date

    We must receive comments by March 20, 2014.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Airbus Model A310-203, -204, -221, -222, -
304, -322, -324, and -325 airplanes, certificated in any category, 
all serial numbers on which Airbus modification number 04797 has 
been embodied in production and those on which Airbus Service 
Bulletin A310-29-2091 has been embodied in service.

(d) Subject

    Air Transport Association (ATA) of America Code 29, Hydraulic 
Power.

(e) Reason

    This AD was prompted by a report of an electrical arc and a 
hydraulic haze in the wheel bay of the left-hand main landing gear 
(MLG) possibly resulting from chafing between a hydraulic high 
pressure hose and electrical wiring of the green electrical motor 
pump (EMP). We are issuing this AD to prevent chafing of hydraulic 
pressure hoses and electrical wiring of the green EMPs, which, in 
combination with a system failure, could cause an uncontrolled and 
undetected fire in the MLG bay.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Actions

    Within 36 months after the effective date of this AD, modify the 
electrical routing of the electrical motor pump (EMP) power supply 
in the hydraulic bay at frame 54 on the left-hand side and replace 
the union elbows to re-route the delivery pipe at the upper EMP, in 
accordance with the Accomplishment Instructions of Airbus Mandatory 
Service Bulletin A310-29-2103, dated December 21, 2012.

(h) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Branch, ANM-116, FAA, has the authority to approve 
AMOCs for this AD, if requested using the procedures found in 14 CFR 
39.19. In accordance with 14 CFR 39.19, send your request to your 
principal inspector or local Flight Standards District Office, as 
appropriate. If sending information directly to the International 
Branch, send it to ATTN: Dan Rodina, Aerospace Engineer, 
International Branch, ANM-116, Transport Airplane Directorate, FAA, 
1601 Lind Avenue SW., Renton, WA 98057-3356; telephone (425) 227-
2125; fax (425) 227-1149. Information may be emailed to: 9-ANM-116-AMOC-REQUESTS@faa.gov. Before using any approved AMOC, notify your 
appropriate principal inspector, or lacking a principal inspector, 
the manager of the local flight standards district office/
certificate holding district office. The AMOC approval letter must 
specifically reference this AD.
    (2) Airworthy Product: For any requirement in this AD to obtain 
corrective actions from a manufacturer, use these actions if they 
are FAA-approved. Corrective actions are considered FAA-approved if 
they were approved by the State of Design Authority (or its 
delegated agent, or the DAH with a State of Design Authority's 
design organization approval). For a repair method to be approved, 
the repair approval must specifically refer to this AD. You are 
required to ensure the product is airworthy before it is returned to 
service.

(i) Related Information

    (1) Refer to Mandatory Continuing Airworthiness Information 
(MCAI) European Aviation Safety Agency Airworthiness Directive 2013-
0165, dated July 25, 2013, for related information. This MCAI may be 
found in the AD docket on the Internet at http://www.regulations.gov 
by searching for and locating it in Docket No. FAA-2014-0005.
    (2) For service information identified in this AD, contact 
Airbus SAS, Airworthiness Office--EAW, 1 Rond Point Maurice 
Bellonte, 31707 Blagnac Cedex, France; telephone +33 5 61 93 36 96; 
fax +33 5 61 93 44 51; email account.airworth-eas@airbus.com; 
Internet http://www.airbus.com. You may view this service 
information at the FAA, Transport Airplane Directorate, 1601 Lind 
Avenue SW., Renton, WA. For information on the availability of this 
material at the FAA, call 425-227-1221.

    Issued in Renton, Washington, on January 22, 2014.
Jeffrey E. Duven,
Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2014-02158 Filed 1-31-14; 8:45 am]
BILLING CODE 4910-13-P


