
[Federal Register Volume 78, Number 250 (Monday, December 30, 2013)]
[Proposed Rules]
[Pages 79338-79340]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: 2013-31188]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2013-1067; Directorate Identifier 2013-NM-164-AD]
RIN 2120-AA64


Airworthiness Directives; Bombardier, Inc. Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to adopt a new airworthiness directive (AD) for 
certain Bombardier, Inc. Model DHC-8-400 series airplanes. This 
proposed AD was prompted by reports of missing clamps that are required 
to provide positive separation between the alternating current (AC) 
feeder cables and the hydraulic line of the landing gear alternate 
extension. This proposed AD would require inspecting for missing 
clamps, and related investigative and corrective actions if necessary. 
We are proposing this AD to detect and correct chafing of the AC feeder 
cable. A chafed and arcing AC feeder cable could puncture the adjacent 
hydraulic line, which, in combination with the use of the alternate 
extension system, could result in an in-flight fire.

DATES: We must receive comments on this proposed AD by February 13, 
2014.

ADDRESSES: You may send comments by any of the following methods:
     Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: (202) 493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC 20590.
     Hand Delivery: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC, between 9 a.m. and 5 p.m., Monday 
through Friday, except Federal holidays.
    For service information identified in this proposed AD, contact 
Bombardier, Inc., Q-Series Technical Help Desk, 123 Garratt Boulevard, 
Toronto, Ontario M3K 1Y5, Canada; telephone 416-375-4000; fax 416-375-
4539; email thd.qseries@aero.bombardier.com; Internet http://www.bombardier.com. You may view this referenced service information at 
the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, 
WA. For information on the availability of this material at the FAA, 
call 425-227-1221.

Examining the AD Docket

    You may examine the AD docket on the Internet at http://www.regulations.gov; or in person at the Docket Management Facility 
between 9 a.m. and 5 p.m., Monday through Friday, except Federal 
holidays. The AD docket contains this proposed AD, the regulatory 
evaluation, any comments received, and other information. The street 
address for the Docket Operations office (telephone (800) 647-5527) is 
in the ADDRESSES section. Comments will be available in the AD docket 
shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Assata Dessaline, Aerospace Engineer, 
Avionics and Service Branch, ANE-172, FAA, New York Aircraft 
Certification Office, 1600 Stewart Avenue, Suite 410, Westbury, New 
York 11590; telephone (516) 228-7301; fax (516) 794-5531.

SUPPLEMENTARY INFORMATION:

Comments Invited

    We invite you to send any written relevant data, views, or 
arguments about this proposed AD. Send your comments

[[Page 79339]]

to an address listed under the ADDRESSES section. Include ``Docket No. 
FAA-2013-1067; Directorate Identifier 2013-NM-164-AD'' at the beginning 
of your comments. We specifically invite comments on the overall 
regulatory, economic, environmental, and energy aspects of this 
proposed AD. We will consider all comments received by the closing date 
and may amend this proposed AD based on those comments.
    We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this proposed AD.

Discussion

    Transport Canada Civil Aviation (TCCA), which is the aviation 
authority for Canada, has issued Canadian Airworthiness Directive CF-
2013-16, dated June 14, 2013 (referred to after this as the Mandatory 
Continuing Airworthiness Information, or ``the MCAI''), to correct an 
unsafe condition for the specified products. The MCAI states:

    During production checks, it was found that the appropriate 
clamps required to provide positive separation between the AC feeder 
cables and the hydraulic line of the landing gear alternate 
extension were omitted. The AC feeder cable could sag and be in 
direct contact with the swage fitting of the landing gear alternate 
extension hydraulic line, resulting in chafing of the AC feeder 
cable. The chafed and arcing AC feeder cable could puncture the 
adjacent hydraulic line. In combination with the use of the 
alternate extension system, this could result in an in-flight fire.
    This [TCCA] AD mandates the [general visual] inspection [for 
missing clamps], and rectification [related investigative and 
corrective actions] as necessary, for proper clamp installation.

The related investigative action is a general visual inspection of the 
AC power feeder cables and the hydraulic line for damage due to 
chafing. The corrective actions include repair of chafed parts, and 
replacement of missing clamps. You may examine the MCAI in the AD 
docket on the Internet at http://www.regulations.gov by searching for 
and locating it in Docket No. FAA-2013-1067.

Relevant Service Information

    Bombardier, Inc. has issued Bombardier Service Bulletin 84-24-53, 
Revision A, dated May 16, 2013. The actions described in this service 
information are intended to correct the unsafe condition identified in 
the MCAI.

FAA's Determination and Requirements of This Proposed AD

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to our bilateral agreement with the State of Design Authority, we have 
been notified of the unsafe condition described in the MCAI and service 
information referenced above. We are proposing this AD because we 
evaluated all pertinent information and determined an unsafe condition 
exists and is likely to exist or develop on other products of the same 
type design.

Costs of Compliance

    We estimate that this proposed AD affects 78 airplanes of U.S. 
registry.
    We also estimate that it would take about 2 work-hours per product 
to comply with the basic requirements of this proposed AD. The average 
labor rate is $85 per work-hour. Based on these figures, we estimate 
the cost of this proposed AD on U.S. operators to be $13,260, or $170 
per product.
    In addition, we estimate that any necessary follow-on actions would 
take about 2 work-hours and require parts costing $11, for a cost of 
$181 per product. We have received no definitive data that would enable 
us to provide cost estimates for the on-condition repair of the AC 
power feeder cables and hydraulic lines specified in this proposed AD. 
We have no way of determining the number of aircraft that might need 
these actions.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more detail the scope of the Agency's 
authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This proposed regulation is 
within the scope of that authority because it addresses an unsafe 
condition that is likely to exist or develop on products identified in 
this rulemaking action.

Regulatory Findings

    We determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979);
    3. Will not affect intrastate aviation in Alaska; and
    4. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

Bombardier, Inc.: Docket No. FAA-2013-1067; Directorate Identifier 
2013-NM-164-AD.

(a) Comments Due Date

    We must receive comments by February 13, 2014.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Bombardier, Inc. Model DHC-8-400, -401, and -
402 airplanes, certificated in any category, serial numbers 4001 
through 4347 inclusive.

(d) Subject

    Air Transport Association (ATA) of America Code 24, Electrical 
power.

(e) Reason

    This AD was prompted by reports of missing clamps that are 
required to provide positive separation between the alternating 
current (AC) feeder cables and the hydraulic line of the landing 
gear alternate extension.

[[Page 79340]]

We are issuing this AD to detect and correct chafing of the AC 
feeder cable. A chafed and arcing AC feeder cable could puncture the 
adjacent hydraulic line, which, in combination with the use of the 
alternate extension system, could result in an in-flight fire.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Clamp Inspection, Related Investigative Actions, and Corrective 
Actions

    Within 6,000 flight hours or 36 months after the effective date 
of this AD, whichever occurs earlier: Do a general visual inspection 
for installation of clamps between the AC feeder cables and 
hydraulic line; and do all applicable related investigative and 
corrective actions; in accordance with the Accomplishment 
Instructions of Bombardier Service Bulletin 84-24-53, Revision A, 
dated May 16, 2013. Do all applicable related investigative and 
corrective actions before further flight.

(h) Credit for Previous Actions

    This paragraph provides credit for actions required by paragraph 
(g) of this AD, if those actions were performed before the effective 
date of this AD using Bombardier Service Bulletin 84-24-53, dated 
May 11, 2012.

(i) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, New 
York Aircraft Certification Office (ACO), ANE-170, FAA, has the 
authority to approve AMOCs for this AD, if requested using the 
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, 
send your request to your principal inspector or local Flight 
Standards District Office, as appropriate. If sending information 
directly to the ACO, send it to ATTN: Program Manager, Continuing 
Operational Safety, FAA, New York ACO, 1600 Stewart Avenue, Suite 
410, Westbury, NY 11590; telephone 516-228-7300; fax 516-794-5531. 
Before using any approved AMOC, notify your appropriate principal 
inspector, or lacking a principal inspector, the manager of the 
local flight standards district office/certificate holding district 
office. The AMOC approval letter must specifically reference this 
AD.
    (2) Airworthy Product: For any requirement in this AD to obtain 
corrective actions from a manufacturer, use these actions if they 
are FAA-approved. Corrective actions are considered FAA-approved if 
they were approved by the State of Design Authority (or its 
delegated agent, or the DAH with a State of Design Authority's 
design organization approval). For a repair method to be approved, 
the repair approval must specifically refer to this AD. You are 
required to ensure the product is airworthy before it is returned to 
service.

(j) Related Information

    (1) Refer to Mandatory Continuing Airworthiness Information 
(MCAI) Canadian Airworthiness Directive CF-2013-16, dated June 14, 
2013, for related information. This MCAI may be found in the AD 
docket on the Internet at http://www.regulations.gov by searching 
for and locating it in Docket No. FAA-2013-1067.
    (2) For service information identified in this AD, contact 
Bombardier, Inc., Q-Series Technical Help Desk, 123 Garratt 
Boulevard, Toronto, Ontario M3K 1Y5, Canada; telephone 416-375-4000; 
fax 416-375-4539; email thd.qseries@aero.bombardier.com; Internet 
http://www.bombardier.com. You may view this service information at 
the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., 
Renton, WA. For information on the availability of this material at 
the FAA, call 425-227-1221.

    Issued in Renton, Washington, on December 20, 2013.
Jeffrey E. Duven,
Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2013-31188 Filed 12-27-13; 8:45 am]
BILLING CODE 4910-13-P


