
[Federal Register Volume 78, Number 216 (Thursday, November 7, 2013)]
[Proposed Rules]
[Pages 66859-66861]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: 2013-26708]


=======================================================================
-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2013-0869; Directorate Identifier 2013-NM-063-AD]
RIN 2120-AA64


Airworthiness Directives; the Boeing Company Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to adopt a new airworthiness directive (AD) for 
certain The Boeing Company Model 767 airplanes. This proposed AD was 
prompted by reports of bearing damage at certain trailing edge (TE) 
flap support rib assemblies. This proposed AD would require inspecting 
certain TE flap support rib assemblies to determine if the bearings 
have a roller retention feature, and performing corrective actions if 
necessary; and inspecting for bearing damage of each pair of removed 
bearings, and performing related investigative and corrective actions 
if necessary. We are proposing this AD to detect and correct damage to 
the TE flap support bearings, which can result in damage to the TE 
rotary actuators and consequent dual flap drive system disconnect in 
both TE flap rotary actuators, and a possible flap aerodynamic blowback 
with loss of controllability of the airplane.

DATES: We must receive comments on this proposed AD by December 23, 
2013.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    For service information identified in this proposed AD, contact 
Boeing Commercial Airplanes, Attention: Data & Services Management, 
P.O. Box 3707, MC 2H-65, Seattle, WA 98124-2207; telephone 206-544-
5000, extension 1; fax 206-766-5680; Internet https://www.myboeingfleet.com. You may review copies of the referenced service 
information at the FAA, Transport Airplane Directorate, 1601 Lind 
Avenue SW., Renton, WA. For information on the availability of this 
material at the FAA, call 425-227-1221.

Examining the AD Docket

    You may examine the AD docket on the Internet at http://www.regulations.gov; or in person at the Docket Management Facility 
between 9 a.m. and 5 p.m., Monday through Friday, except Federal 
holidays. The AD docket contains this proposed AD, the regulatory 
evaluation, any comments received, and other information. The street 
address for the Docket Office (phone: 800-647-5527) is in the ADDRESSES 
section. Comments will be available in the AD docket shortly after 
receipt.

FOR FURTHER INFORMATION CONTACT: Berhane Alazar, Aerospace Engineer, 
Airframe Branch, ANM-120S, FAA, Seattle Aircraft Certification Office 
(ACO), 1601 Lind Avenue SW., Renton, Washington 98057-3356; phone: 425-
917-6577; fax: 425-917-6590; email: Berhane.Alazar@faa.gov.

SUPPLEMENTARY INFORMATION: 

Comments Invited

    We invite you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under the ADDRESSES section. Include ``Docket No. FAA-2013-0869; 
Directorate Identifier 2013-NM-063-AD'' at the beginning of your 
comments. We specifically invite comments on the overall regulatory, 
economic, environmental, and energy aspects of this proposed AD. We 
will consider all comments received by the closing date and may amend 
this proposed AD because of those comments.
    We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this proposed AD.

Discussion

    We have received reports of bearing damage at the TE flap support 
rib assemblies in flap positions 1, 2, 4, 5, 7, and 8. Bearing damage 
in the TE flap support rib assembly is caused by the use of mallets 
during the installation of the shaft on the TE flap support rib 
assembly when TE flap support bearings without a roller retention 
feature are installed. This method of installation may compromise 
bearings without a roller retention feature. Damaged TE flap support 
bearings can lead to damage to the TE rotary actuators and other TE 
flap support rib parts, which could result in a dual flap drive system 
disconnect in both TE flap rotary actuators, and a possible flap 
aerodynamic blowback with loss of controllability of the airplane.

Relevant Service Information

    We reviewed Boeing Alert Service Bulletin 767-27A0227, dated 
February 12, 2013. For information on the procedures and compliance 
times, see this service information at http://www.regulations.gov by 
searching for Docket No. FAA-2013-0869.

FAA's Determination

    We are proposing this AD because we evaluated all the relevant 
information and determined the unsafe condition described previously is 
likely to exist or develop in other products of the same type design.

Proposed AD Requirements

    This proposed AD would require accomplishing the actions specified 
in the service information identified previously, except as discussed 
under ``Differences Between the Proposed AD and the Service 
Information.''
    The phrase ``related investigative actions'' is used in this 
proposed AD. ``Related investigative actions'' are follow-on actions 
that: (1) Are related to the primary actions, and (2) further

[[Page 66860]]

investigate the nature of any condition found. Related investigative 
actions in an AD could include, for example, inspections.
    In addition, the phrase ``corrective actions'' is used in this 
proposed AD. ``Corrective actions'' are actions that correct or address 
any condition found. Corrective actions in an AD could include, for 
example, repairs.

Costs of Compliance

    We estimate that this proposed AD affects 45 airplanes of U.S. 
registry.
    We estimate the following costs to comply with this proposed AD:

                                                 Estimated Costs
----------------------------------------------------------------------------------------------------------------
                                                                                                  Cost on U.S.
             Action                     Labor cost           Parts cost     Cost per product       operators
----------------------------------------------------------------------------------------------------------------
Inspection.....................  Up to 40 work-hours x                $0   Up to $3,400......  Up to $153,000.
                                  $85 per hour = Up to
                                  $3,400.
----------------------------------------------------------------------------------------------------------------

    We estimate the following costs to do any necessary replacements 
that would be required based on the results of the proposed inspection. 
We have no way of determining the number of aircraft that might need 
these replacements:

                                               On-Condition Costs
----------------------------------------------------------------------------------------------------------------
               Action                         Labor cost                Parts cost           Cost per product
----------------------------------------------------------------------------------------------------------------
Bearing replacement and functional   Up to 24 work-hours x $85    Up to $5,936..........  Up to $7,976.
 test.                                per hour = Up to $2,040.
----------------------------------------------------------------------------------------------------------------

    According to the manufacturer, some of the costs of this proposed 
AD may be covered under warranty, thereby reducing the cost impact on 
affected individuals. We do not control warranty coverage for affected 
individuals. As a result, we have included all costs in our cost 
estimate.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979),
    (3) Will not affect intrastate aviation in Alaska, and
    (4) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

The Boeing Company: Docket No. FAA-2013-0869; Directorate Identifier 
2013-NM-063-AD.

(a) Comments Due Date

    We must receive comments by December 23, 2013.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to The Boeing Company Model 767-200, -300, -
300F, and -400ER series airplanes, certificated in any category, as 
identified in Boeing Alert Service Bulletin 767-27A0227, dated 
February 12, 2013.

(d) Subject

    Joint Aircraft System Component (JASC)/Air Transport Association 
(ATA) of America Code 27, Flight controls.

(e) Unsafe Condition

    This AD was prompted by reports of bearing damage at certain 
trailing edge (TE) flap support rib assemblies. We are issuing this 
AD to detect and correct damage to the TE flap support bearings, 
which can result in damage to the TE rotary actuators and consequent 
dual flap drive system disconnect in both TE flap rotary actuators, 
and a possible flap aerodynamic blowback with loss of 
controllability of the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Bearing Inspection To Determine Roller Retention Feature and 
Corrective Actions

    Except as provided by paragraph (i) of this AD, at the 
applicable time specified in paragraph 1.E., ``Compliance,'' of 
Boeing Alert Service Bulletin 767-27A0227, dated February 12, 2013: 
Do a general visual inspection of both bearings at the TE flap 
support rib assembly in flap positions 1, 2, 7, and 8 to determine 
if the bearings have a roller retention feature; and do all 
applicable corrective actions; in accordance with the Accomplishment 
Instructions of Boeing Alert

[[Page 66861]]

Service Bulletin 767-27A0227, dated February 12, 2013. Do all 
applicable corrective actions before further flight.

(h) Bearing Inspection for Damage, Related Investigative Actions, and 
Corrective Actions

    For each pair of bearings removed as required by paragraph (g) 
of this AD: At the applicable time specified in paragraph 1.E., 
``Compliance,'' of Boeing Alert Service Bulletin 767-27A0227, dated 
February 12, 2013: Do a general visual inspection for bearing damage 
of the bearings; and do all applicable related investigative and 
corrective actions; in accordance with the Accomplishment 
Instructions of Boeing Alert Service Bulletin 767-27A0227, dated 
February 12, 2013. Do all applicable related investigative and 
corrective actions before further flight.

(i) Exception to Compliance Time

    Where paragraph 1.E., ``Compliance,'' of Boeing Alert Service 
Bulletin 767-27A0227, dated February 12, 2013, specifies a 
compliance time ``after the original issue date of this service 
bulletin,'' this AD requires compliance within the specified 
compliance time ``after the effective date of this AD.''

(j) Credit for Previous Actions Accomplished in Accordance With 
Previous Service Information

    This paragraph provides credit for the actions specified in 
paragraphs (g) and (h) of this AD, if those actions were performed 
before the effective date of this AD using of Boeing Alert Service 
Bulletin 767-27A0222, dated June 24, 2010, which is not incorporated 
by reference in this AD.

(k) Alternative Methods of Compliance (AMOCs)

    (1) The Manager, Seattle Aircraft Certification Office (ACO), 
FAA, has the authority to approve AMOCs for this AD, if requested 
using the procedures found in 14 CFR 39.19. In accordance with 14 
CFR 39.19, send your request to your principal inspector or local 
Flight Standards District Office, as appropriate. If sending 
information directly to the manager of the ACO, send it to the 
attention of the person identified in the Related Information 
section of this AD. Information may be emailed to: 9-ANM-Seattle-ACO-AMOC-Requests@faa.gov.
    (2) Before using any approved AMOC, notify your appropriate 
principal inspector, or lacking a principal inspector, the manager 
of the local flight standards district office/certificate holding 
district office.
    (3) An AMOC that provides an acceptable level of safety may be 
used for any repair required by this AD if it is approved by the 
Boeing Commercial Airplanes Organization Designation Authorization 
(ODA) that has been authorized by the Manager, Seattle ACO, to make 
those findings. For a repair method to be approved, the repair must 
meet the certification basis of the airplane, and the approval must 
specifically refer to this AD.

(l) Related Information

    (1) For more information about this AD, contact Berhane Alazar, 
Aerospace Engineer, Airframe Branch, ANM-120S, FAA, Seattle Aircraft 
Certification Office (ACO), 1601 Lind Avenue SW., Renton, WA 98057-
3356; phone: 425-917-6577; fax: 425-917-6590; email: 
Berhane.Alazar@faa.gov.
    (2) For service information identified in this AD, contact 
Boeing Commercial Airplanes, Attention: Data & Services Management, 
P.O. Box 3707, MC 2H-65, Seattle, WA 98124-2207; telephone 206-544-
5000, extension 1; fax 206-766-5680; Internet https://www.myboeingfleet.com. You may review copies of the referenced 
service information at the FAA, Transport Airplane Directorate, 1601 
Lind Avenue SW., Renton, WA. For information on the availability of 
this material at the FAA, call 425-227-1221.

    Issued in Renton, Washington, on October 31, 2013.
Jeffrey E. Duven,
Acting Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2013-26708 Filed 11-6-13; 8:45 am]
BILLING CODE 4910-13-P


