
[Federal Register Volume 78, Number 98 (Tuesday, May 21, 2013)]
[Proposed Rules]
[Pages 29669-29672]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: 2013-12077]



[[Page 29669]]

-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2013-0423; Directorate Identifier 2012-NM-176-AD]
RIN 2120-AA64


Airworthiness Directives; DASSAULT AVIATION Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to adopt a new airworthiness directive (AD) for all 
DASSAULT AVIATION Model FAN JET FALCON, FAN JET FALCON SERIES C, D, E, 
F, and G airplanes; Model MYSTERE-FALCON 200 airplanes; and Model 
MYSTERE-FALCON 20-C5, 20-D5, 20-E5, and 20-F5 airplanes. This proposed 
AD was prompted by reports of a manufacturing defect in the charge 
indicator on fire extinguisher bottles. This proposed AD would require 
repetitive weighing of fire extinguisher bottles having a certain part 
number, and eventual replacement of those bottles to terminate the 
repetitive weighing. We are proposing this AD to detect and correct a 
dormant failure in the fire suppression system, which could result in 
the inability to put out a fire in an engine, auxiliary power unit, or 
rear compartment.

DATES: We must receive comments on this proposed AD by July 5, 2013.

ADDRESSES: You may send comments by any of the following methods:
     Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC 20590.
     Hand Delivery: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC, between 9 a.m. and 5 p.m., Monday 
through Friday, except Federal holidays.
    For service information identified in this proposed AD, contact
    Dassault Falcon Jet, P.O. Box 2000, South Hackensack, NJ 07606; 
telephone 201-440-6700; Internet http://www.dassaultfalcon.com. You may 
review copies of the referenced service information at the FAA, 
Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For 
information on the availability of this material at the FAA, call 425-
227-1221.

Examining the AD Docket

    You may examine the AD docket on the Internet at http://www.regulations.gov; or in person at the Docket Operations office 
between 9 a.m. and 5 p.m., Monday through Friday, except Federal 
holidays. The AD docket contains this proposed AD, the regulatory 
evaluation, any comments received, and other information. The street 
address for the Docket Operations office (telephone (800) 647-5527) is 
in the ADDRESSES section. Comments will be available in the AD docket 
shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Tom Rodriguez, Aerospace Engineer, 
International Branch, ANM-116, Transport Airplane Directorate, FAA, 
1601 Lind Avenue SW., Renton, WA 98057-3356; phone: 425-227-1137; fax: 
425-227-1149.

SUPPLEMENTARY INFORMATION:

Comments Invited

    We invite you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under the ADDRESSES section. Include ``Docket No. FAA-2013-0423; 
Directorate Identifier 2012-NM-176-AD'' at the beginning of your 
comments. We specifically invite comments on the overall regulatory, 
economic, environmental, and energy aspects of this proposed AD. We 
will consider all comments received by the closing date and may amend 
this proposed AD because of those comments.
    We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this proposed AD.

Discussion

    The European Aviation Safety Agency (EASA), which is the Technical 
Agent for Member States of the European Community, has issued EASA 
Airworthiness Directive 2012-0189, dated September 24, 2012 (referred 
to after this as ``the MCAI''), to correct an unsafe condition for the 
specified products. The MCAI states:

    A manufacturing defect of the charge indicator of fire 
extinguisher bottles has been reported on Dassault Aviation Fan Jet 
Falcon and Myst[egrave]re-Falcon 20 series aeroplanes.
    The results of the investigations concluded that this defect may 
lead to corrosion of the charge indicator, causing improper 
indication of loss of pressure inside the bottle. In addition, the 
Part Numbers (P/N) of the fire extinguishers and batch numbers of 
the affected charge indicators have been identified.
    This condition, if not detected and corrected, could constitute 
a dormant failure that might impact the capability to extinguish a 
fire, either in an engine or the Auxiliary Power Unit (APU) or the 
rear compartment, possibly resulting in damage to the aeroplane and 
injury to the occupants.
    For the reasons described above, this [EASA] AD requires 
repetitive weighing of the affected fire extinguishers bottles and, 
ultimately replacement of the affected bottles with serviceable 
bottles. In addition, this AD prohibits installation of an affected 
fire extinguisher bottle.

    You may obtain further information by examining the MCAI in the AD 
docket.

Relevant Service Information

    Dassault Aviation has issued the following service information:
     Mandatory Service Bulletin F20-785, dated June 11, 2012 
(for Model FAN JET FALCON, FAN JET FALCON SERIES C, D, E, F, and G 
airplanes; and MYSTERE-FALCON 20-C5, 20-D5, 20-E5, and 20-F5 
airplanes);
     Mandatory Service Bulletin F200-131, dated June 11, 2012 
(for Model MYSTERE-FALCON 200 airplanes);
     Dassault Maintenance Procedure 26-20-3, ``Weighing of 
Engine Freon Fire Extinguishers,'' dated October 2009, of Chapter 26 of 
Book 2 of the Falcon 20 Maintenance Manual (for Model FAN JET FALCON, 
FAN JET FALCON SERIES C, D, E, F, and G airplanes; and Model MYSTERE-
FALCON 20-C5, 20-D5, 20-E5, and 20-F5 airplanes);
     Dassault Aviation Maintenance Procedure 26-20-2, ``Removal 
of Pyrotechnical Cartridge for Check/Replacement,'' dated October 2010, 
of Chapter 26 of Book 2 of the Falcon 20 Maintenance Manual (for Model 
FAN JET FALCON, FAN JET FALCON SERIES C, D, E, F, and G airplanes; and 
Model MYSTERE-FALCON 20-C5, 20-D5, 20-E5, and 20-F5 airplanes);
     Dassault Aviation Falcon 200 Maintenance Requirement Card 
171.0, ``Engine/Rear compartment Extinguisher (14W1-14W2)--Removal/
Installation (ATA 26-20-06), dated December 2011, of Chapter 26 of Book 
1 of the Falcon 200 Maintenance Manual (for Model MYSTERE-FALCON 200 
airplanes); and
     Dassault Aviation Falcon 200 Maintenance Requirement Card 
171.0, ``Engine/Rear compartment Extinguisher (14W1-14W2)--Check/
Replacement of Percussion Cartridge (ATA 26-20-08),'' dated December 
2011, of Chapter 26 of Book 1 of the Falcon 200 Maintenance

[[Page 29670]]

Manual (for Model MYSTERE-FALCON 200 airplanes).
    The actions described in this service information are intended to 
correct the unsafe condition identified in the MCAI.

FAA's Determination and Requirements of This Proposed AD

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to our bilateral agreement with the State of Design Authority, we have 
been notified of the unsafe condition described in the MCAI and service 
information referenced above. We are proposing this AD because we 
evaluated all pertinent information and determined an unsafe condition 
exists and is likely to exist or develop on other products of the same 
type design.

Costs of Compliance

    Based on the service information, we estimate that this proposed AD 
would affect about 185 products of U.S. registry. We also estimate that 
it would take about 4 work-hours per product to comply with the basic 
requirements of this proposed AD. The average labor rate is $85 per 
work-hour. Required parts would cost about $6,400 per product. Where 
the service information lists required parts costs that are covered 
under warranty, we have assumed that there will be no charge for these 
parts. As we do not control warranty coverage for affected parties, 
some parties may incur costs higher than estimated here. Based on these 
figures, we estimate the cost of the proposed AD on U.S. operators to 
be up to $1,246,900, or $6,740 per product.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979),
    (3) Will not affect intrastate aviation in Alaska, and
    (4) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.
    We prepared a regulatory evaluation of the estimated costs to 
comply with this proposed AD and placed it in the AD docket.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

Dassault Aviation: Docket No. FAA-2013-0423; Directorate Identifier 
2012-NM-176-AD.

(a) Comments Due Date

    We must receive comments by July 5, 2013.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to DASSAULT AVIATION Model FAN JET FALCON, FAN 
JET FALCON SERIES C, D, E, F, and G airplanes; Model MYSTERE-FALCON 
200 airplanes; and Model MYSTERE-FALCON 20-C5, 20-D5, 20-E5, and 20-
F5 airplanes, certificated in any category, all serial numbers.

(d) Subject

    Joint Aircraft System Component (JASC)/Air Transport Association 
(ATA) of America Code 26, Fire protection.

(e) Reason

    This AD was prompted by reports of a manufacturing defect in the 
charge indicator on fire extinguisher bottles. We are issuing this 
AD to detect and correct a dormant failure in the fire suppression 
system, which could result in the inability to put out a fire in an 
engine, auxiliary power unit, or rear compartment.

(f) Compliance

    You are responsible for having the actions required by this AD 
performed within the compliance times specified, unless the actions 
have already been done.

(g) Definitions

    For the purposes of this AD the following definitions apply:
    (1) An affected fire extinguisher bottle is any fire 
extinguisher bottle having a part number (P/N) included in table 1 
to paragraph (h) of this AD and having a manufacturing batch number 
168 through 200 inclusive on the data plate of the charge indicator.
    (2) A serviceable fire extinguisher bottle is any fire 
extinguisher bottle having a manufacturing batch number lower than 
168 or higher than 200 on the charge indicator data plate.

(h) Determining Charge Indicator Batch Number

    Within 30 days or 100 flight hours after the effective date of 
this AD, whichever occurs first: Determine the manufacturing batch 
number for the charge indicator installed on each engine and 
auxiliary power unit (APU) fire extinguisher bottle having a part 
number (P/N) included in table 1 to paragraph (h) of this AD, in 
accordance with the Accomplishment Instructions of Dassault 
Mandatory Service Bulletin F20-785, dated June 11, 2012 (for Model 
FAN JET FALCON, FAN JET FALCON SERIES C, D, E, F, and G airplanes; 
and Model MYSTERE-FALCON 20-C5, 20-D5, 20-E5, and 20-F5 airplanes); 
or Dassault Mandatory Service Bulletin F200-131, dated June 11, 2012 
(for Model MYSTERE-FALCON 200 airplanes).

 Table 1 to Paragraph (h) of This AD--Affected Fire Extinguisher Bottles
------------------------------------------------------------------------
          Type of Bottle--                          P/N--
------------------------------------------------------------------------
Engine Fire Extinguisher Bottle....  P/N 111-1555-324-12A.
                                     P/N 811456.
                                     P/N 111-355-32142A.
APU Fire Extinguisher Bottle.......  P/N 111-011-324-12A.
                                     P/N 811475.
------------------------------------------------------------------------


[[Page 29671]]

     (1) For fire extinguisher bottles with P/Ns that are not 
included in table 1 to paragraph (h) of this AD, no further action 
is required by this paragraph.
    (2) For any affected charge indicator, as identified in 
paragraph (g)(1) of this AD: Before further flight, weigh each 
affected fire extinguisher bottle, in accordance with the 
instructions specified in Dassault Maintenance Procedure 26-20-3, 
``Weighing of Engine Freon Fire Extinguishers,'' dated October 2009, 
of Chapter 26 of Book 2 of the Falcon 20 Maintenance Manual (for 
Model FAN JET FALCON, FAN JET FALCON SERIES C, D, E, F, and G 
airplanes; and Model MYSTERE-FALCON 20-C5, 20-D5, 20-E5, and 20-F5 
airplanes); or Dassault Aviation Falcon 200 Maintenance Requirement 
Card 171.0, ``Engine/Rear compartment Extinguisher (14W1-14W2)--
Removal/Installation (ATA 26-20-06),'' dated December 2011, of 
Chapter 26 of Book 1 of the Falcon 200 Maintenance Manual (for Model 
MYSTERE-FALCON 200 airplanes). Weigh the fire extinguishers 
thereafter at intervals not to exceed 12 months until the 
replacement specified in paragraph (h)(2)(i), (h)(2)(ii), 
(h)(2)(iii), (h)(2)(iv), or (j) of this AD is accomplished. If it is 
determined that the fire extinguisher weighs less than the lowest 
weight limit indicated on the fire extinguisher's data plate, before 
further flight, replace any affected fire extinguisher bottle and 
charge indicator cartridge, with a serviceable part, in accordance 
with the applicable service information or method specified in 
paragraph (h)(2)(i), (h)(2)(ii), (h)(2)(iii), or (h)(2)(iv) of this 
AD.
    (i) For Model FAN JET FALCON, FAN JET FALCON SERIES C, D, E, F, 
and G airplanes; and Model MYSTERE-FALCON 20-C5, 20-D5, 20-E5, and 
20-F5 airplanes: Replace the charge indicator cartridge with a 
serviceable part, in accordance with the instructions specified in 
Dassault Aviation Maintenance Procedure 26-20-2, ``Removal of 
Pyrotechnical Cartridge for Check/Replacement,'' dated October 2010, 
of Chapter 26 of Book 2 of the Falcon 20 Maintenance Manual.
    (ii) For Model FAN JET FALCON, FAN JET FALCON SERIES C, D, E, F, 
and G airplanes; and Model MYSTERE-FALCON 20-C5, 20-D5, 20-E5, and 
20-F5 airplanes: Replace the fire extinguisher bottle with a 
serviceable part, in accordance with a method approved by the 
Manager, International Branch, ANM-116, Transport Airplane 
Directorate, FAA; or the European Aviation Safety Agency (EASA) (or 
its delegated agent).
    (iii) For Model MYSTERE-FALCON 200 airplanes: Replace the charge 
indicator cartridge with a serviceable part, in accordance with 
Dassault Aviation Falcon 200 Maintenance Requirement Card 171.0, 
``Engine/Rear compartment Extinguisher (14W1-14W2)--Check/
Replacement of Percussion Cartridge (ATA 26-20-08),'' dated December 
2011, of Chapter 26 of Book 1 of the Falcon 200 Maintenance Manual.
    (iv) For Model MYSTERE-FALCON 200 airplanes: Replace the fire 
extinguisher bottle with a serviceable part, in accordance with the 
instructions specified in Dassault Aviation Falcon 200 Maintenance 
Requirement Card 171.0, ``Engine/Rear compartment Extinguisher 
(14W1-14W2)--Removal/Installation (ATA 26-20-06),'' dated December 
2011, of Chapter 26 of Book 1 of the Falcon 200 Maintenance Manual.

(i) Repetitive Inspection To Determine If Charge Indicator Cartridge 
Was Fired

    Within 6 months after the effective date of this AD: Do an 
inspection to determine if the charge indicator cartridge installed 
on each engine and APU fire extinguisher bottle, as identified in 
table 1 to paragraph (h) of this AD, was fired, in accordance with 
the instructions specified in Dassault Aviation Maintenance 
Procedure 26-20-2, ``Removal of Pyrotechnical Cartridge for Check/
Replacement,'' dated October 2010, of Chapter 26 of Book 2 of the 
Falcon 20 Maintenance Manual (for Model FAN JET FALCON, FAN JET 
FALCON SERIES C, D, E, F, and G airplanes; and Model MYSTERE-FALCON 
20-C5, 20-D5, 20-E5, and 20 F5 airplanes); or Dassault Aviation 
Falcon 200 Maintenance Requirement Card 171.0, ``Engine/Rear 
compartment Extinguisher (14W1-14W2)--Check/Replacement of 
Percussion Cartridge (ATA 26-20-08),'' dated December 2011, of 
Chapter 26 of Book 1 of the Falcon 200 Maintenance Manual (for Model 
MYSTERE-FALCON 200 airplanes). Repeat the inspection thereafter at 
intervals not to exceed 6 months until the replacement specified in 
paragraph (i)(1), (i)(2), (i)(3), (i)(4), or (j) of this AD is 
accomplished. If it is determined that any charge indicator 
cartridge was fired, before further flight, replace the affected 
fire extinguisher bottle and charge indicator cartridge with a 
serviceable part in accordance with the applicable service 
information or method specified in paragraph (i)(1), (i)(2), (i)(3), 
or (i)(4) of this AD.
    (1) For Model FAN JET FALCON, FAN JET FALCON SERIES C, D, E, F, 
and G airplanes; and Model MYSTERE-FALCON 20-C5, 2-D5, 20-E5, and 
20-F5 airplanes: Replace the charge indicator cartridge with a 
serviceable part, in accordance with the instructions specified in 
Dassault Aviation Maintenance Procedure 26-20-2, ``Removal of 
Pyrotechnical Cartridge for Check/Replacement,'' dated October 2010, 
of Chapter 26 of Book 2 of the Falcon 20 Maintenance Manual.
    (2) For Model FAN JET FALCON, FAN JET FALCON SERIES C, D, E, F, 
and G airplanes; and Model MYSTERE-FALCON 20-C5, 20-D5, 20-E5, and 
20-F5 airplanes: Replace the fire extinguisher bottle with a 
serviceable part, in accordance with a method approved by the 
Manager, International Branch, ANM-116, Transport Airplane 
Directorate, FAA; or the European Aviation Safety Agency (EASA) (or 
its delegated agent).
    (3) For Model MYSTERE-FALCON 200 airplanes: Replace the charge 
indicator cartridge with a serviceable part, in accordance with the 
instructions specified in Dassault Aviation Falcon 200 Maintenance 
Requirement Card 171.0, ``Engine/Rear compartment Extinguisher 
(14W1-14W2)--Check/Replacement of Percussion Cartridge (ATA 26-20-
08),'' dated December 2011, of Chapter 26 of Book 1 of the Falcon 
200 Maintenance Manual.
    (4) For Model MYSTERE-FALCON 200 airplanes: Replace the fire 
extinguisher bottle with a serviceable part, in accordance with the 
instructions specified in Dassault Aviation Falcon 200 Maintenance 
Requirement Card 171.0, ``Engine/Rear compartment Extinguisher 
(14W1-14W2)--Removal/Installation (ATA 26-20-06), dated December 
2011, of Chapter 26 of Book 1 of the Falcon 200 Maintenance Manual.

(j) Replacement of Fire Extinguisher Bottle and Charge Indicator 
Cartridge

    Unless previously accomplished as specified in paragraphs (h) or 
(i) of this AD: Within 60 months after the effective date of this 
AD, replace any affected fire extinguisher bottle and charge 
indicator cartridge, as specified in paragraph (g)(1) of this AD, 
with a serviceable part, in accordance with the applicable service 
information or method specified in paragraph (j)(1), (j)(2), (j)(3), 
or (j)(4) of this AD. Replacement of any affected fire extinguisher 
bottle and charge indicator cartridge with a serviceable part 
terminates the repetitive actions specified in paragraphs (h) and 
(i) of this AD.
    (1) For Model FAN JET FALCON, FAN JET FALCON SERIES C, D, E, F, 
and G airplanes; and Model MYSTERE-FALCON 20-C5, 20-D5, 20-E5, and 
20-F5 airplanes: Replace the charge indicator cartridge with a 
serviceable part, in accordance with the instructions specified in 
Dassault Aviation Maintenance Procedure 26-20-2, ``Removal of 
Pyrotechnical Cartridge for Check/Replacement,'' dated October 2010, 
of Chapter 26 of Book 2 of the Falcon 20 Maintenance Manual.
    (2) For Model FAN JET FALCON, FAN JET FALCON SERIES C, D, E, F, 
and G airplanes; and Model MYSTERE-FALCON 20-C5, 20-D5, 20-E5, and 
20-F5 airplanes: Replace the fire extinguisher bottle with a 
serviceable part, in accordance with a method approved by the 
Manager, International Branch, ANM-116, Transport Airplane 
Directorate, FAA; or the EASA (or its delegated agent).
    (3) For Model MYSTERE-FALCON 200 airplanes: Replace the charge 
indicator cartridge with a serviceable part, in accordance with the 
instructions specified in Dassault Aviation Falcon 200 Maintenance 
Requirement Card 171.0, ``Engine/Rear compartment Extinguisher 
(14W1-14W2)--Check/Replacement of Percussion Cartridge (ATA 26-20-
08),'' dated December 2011, of Chapter 26 of Book 1 of the Falcon 
200 Maintenance Manual.
    (4) For Model MYSTERE-FALCON 200 airplanes: Replace the fire 
extinguisher bottle with a serviceable part, in accordance with the 
instructions specified in Dassault Aviation Falcon 200 Maintenance 
Requirement Card 171.0, ``Engine/Rear compartment Extinguisher 
(14W1-14W2)--Removal/Installation (ATA 26-20-06), dated December 
2011, of Chapter 26 of Book 1 of the Falcon 200 Maintenance Manual.

(k) Parts Installation Prohibition

    As of the effective date of this AD, no person may install, on 
any airplane, a fire extinguisher bottle having a P/N included in 
table 1 to paragraph (h) of this AD, fitted with a charge indicator 
having a manufacturing batch number on the data plate of 168 through 
200 inclusive.

[[Page 29672]]

(l) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) AMOCs: The Manager, International Branch, ANM-116, Transport 
Airplane Directorate, FAA, has the authority to approve AMOCs for 
this AD, if requested using the procedures found in 14 CFR 39.19. In 
accordance with 14 CFR 39.19, send your request to your principal 
inspector or local Flight Standards District Office, as appropriate. 
If sending information directly to the International Branch, send it 
to ATTN: Tom Rodriguez, Aerospace Engineer, International Branch; 
ANM-116, Transport Airplane Directorate, FAA, 1601 Lind Avenue SW., 
Renton, Washington 98057-3356; telephone 425-227-1137; fax 425-227-
1137. Information may be emailed to: 9-ANM-116-AMOC-REQUESTS@faa.gov. Before using any approved AMOC, notify your 
appropriate principal inspector, or lacking a principal inspector, 
the manager of the local flight standards district office/
certificate holding district office. The AMOC approval letter must 
specifically reference this AD.
    (2) Airworthy Product: For any requirement in this AD to obtain 
corrective actions from a manufacturer or other source, use these 
actions if they are FAA-approved. Corrective actions are considered 
FAA-approved if they are approved by the State of Design Authority 
(or their delegated agent). You are required to assure the product 
is airworthy before it is returned to service.

(m) Related Information

    (1) Refer to MCAI EASA Airworthiness Directive 2012-0189, dated 
September 24, 2012, and the following service information for 
related information.
    (i) Dassault Mandatory Service Bulletin F20-785, dated June 11, 
2012.
    (ii) Dassault Mandatory Service Bulletin F200-131, dated June 
11, 2012.
    (iii) Dassault Aviation Maintenance Procedure 26-20-2, ``Removal 
of Pyrotechnical Cartridge for Check/Replacement,'' dated October 
2010, of Chapter 26 of Book 2 of the Falcon 20 Maintenance Manual.
    (iv) Dassault Maintenance Procedure 26-20-3, ``Weighing of 
Engine Freon Fire Extinguishers,'' dated October 2009, of Chapter 26 
of Book 2 of the Falcon 20 Maintenance Manual.
    (v) Dassault Aviation Falcon 200 Maintenance Requirement Card 
171.0, ``Engine/Rear compartment Extinguisher (14W1-14W2)--Removal/
Installation (ATA 26-20-06),'' dated December 2011, of Chapter 26 of 
Book 1 of the Falcon 200 Maintenance Manual.
    (vi) Dassault Aviation Falcon 200 Maintenance Requirement Card 
171.0, ``Engine/Rear compartment Extinguisher (14W1-14W2)--Check/
Replacement of Percussion Cartridge (ATA 26-20-08),'' dated December 
2011, of Chapter 26 of Book 1 of the Falcon 200 Maintenance Manual.
    (2) For service information identified in this AD, contact 
Dassault Falcon Jet, P.O. Box 2000, South Hackensack, NJ 07606; 
telephone 201-440-6700; Internet http://www.dassaultfalcon.com. You 
may review copies of the referenced service information at the FAA, 
Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. 
For information on the availability of this material at the FAA, 
call 425-227-1221.

    Issued in Renton, Washington, on May 13, 2013.
Ali Bahrami,
Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2013-12077 Filed 5-20-13; 8:45 am]
BILLING CODE 4910-13-P


