
[Federal Register Volume 78, Number 37 (Monday, February 25, 2013)]
[Proposed Rules]
[Pages 12651-12655]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: 2013-04220]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2013-0146; Directorate Identifier 2012-SW-060-AD]
RIN 2120-AA64


Airworthiness Directives; Agusta S.p.A. Helicopters

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to supersede an existing airworthiness directive 
(AD) for Agusta S.p.A. (Agusta) Model A109E helicopters that requires 
reducing the tail rotor (T/R) blade life limit, modifying a T/R hub and 
grip assembly, re-identifying two T/R assemblies, clarifying the never-
exceed speed (Vne) limitation and reducing the inspection interval. 
Since we issued that AD, the manufacturer has redesigned a T/R grip 
bushing (bushing) that reduces the loads, which caused the T/R 
cracking, on the T/R blades. This action would require installing the 
new bushing and re-identifying the T/R hub-and-grip and hub-and-blade 
assemblies and require a recurring inspection of each bushing. The 
proposed actions are intended to prevent fatigue failure of a T/R blade 
and subsequent loss of control of the helicopter.

DATES: We must receive comments on this proposed AD by April 26, 2013.

ADDRESSES: You may send comments by any of the following methods:
     Federal eRulemaking Docket: Go to http://www.regulations.gov. Follow the online instructions for sending your 
comments electronically.
     Fax: 202-493-2251.
     Mail: Send comments to the U.S. Department of 
Transportation, Docket Operations, M-30, West Building Ground Floor, 
Room W12-140, 1200 New Jersey Avenue SE., Washington, DC 20590-0001.

[[Page 12652]]

     Hand Delivery: Deliver to the ``Mail'' address between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.

Examining the AD Docket

    You may examine the AD docket on the Internet at http://www.regulations.gov or in person at the Docket Operations Office 
between 9 a.m. and 5 p.m., Monday through Friday, except Federal 
holidays. The AD docket contains this proposed AD, the economic 
evaluation, any comments received and other information. The street 
address for the Docket Operations Office (telephone 800-647-5527) is in 
the ADDRESSES section. Comments will be available in the AD docket 
shortly after receipt.
    For service information identified in this proposed AD, contact 
Agusta Westland, Customer Support & Services, Via Per Tornavento 15, 
21019 Somma Lombardo (VA) Italy, ATTN: Giovanni Cecchelli; telephone 
39-0331-711133; fax 39-0331-711180; or at http://www.agustawestland.com/technical-bullettins. You may review a copy of 
the service information at the FAA, Office of the Regional Counsel, 
Southwest Region, 2601 Meacham Blvd., Room 663, Fort Worth, Texas 
76137.

FOR FURTHER INFORMATION CONTACT: Sharon Miles, Aviation Safety 
Engineer, Regulations and Policy Group, Rotorcraft Directorate, FAA, 
2601 Meacham Blvd., Fort Worth, TX 76137; telephone (817) 222-5110; 
email sharon.y.miles@faa.gov.

SUPPLEMENTARY INFORMATION

Comments Invited

    We invite you to participate in this rulemaking by submitting 
written comments, data, or views. We also invite comments relating to 
the economic, environmental, energy, or federalism impacts that might 
result from adopting the proposals in this document. The most helpful 
comments reference a specific portion of the proposal, explain the 
reason for any recommended change, and include supporting data. To 
ensure the docket does not contain duplicate comments, commenters 
should send only one copy of written comments, or if comments are filed 
electronically, commenters should submit only one time.
    We will file in the docket all comments that we receive, as well as 
a report summarizing each substantive public contact with FAA personnel 
concerning this proposed rulemaking. Before acting on this proposal, we 
will consider all comments we receive on or before the closing date for 
comments. We will consider comments filed after the comment period has 
closed if it is possible to do so without incurring expense or delay. 
We may change this proposal in light of the comments we receive.

Discussion

    On June 12, 2002, a T/R blade on an Agusta Model 119 helicopter 
failed and resulted in an autorotative landing. As a result of this 
failure, based on the commonality of the T/R blades on the model 109E 
helicopter, Agusta issued Alert Bollettino Tecnico (ABT) No. 109EP-30, 
dated June 21, 2002, for the Model 109E helicopter. The aviation 
authority for Italy, Ente Nazionale per L'Aviazione Civile (ENAC), 
issued Emergency AD No. 2002-340, dated June 28, 2002, for the Model 
109E helicopters. On July 9, 2002, we issued Emergency AD 2002-14-51 to 
require a pilot-check before each flight, and initial and repetitive 
inspections of the T/R blades for a crack.
    ``As a precautionary measure,'' Agusta issued Revision A, dated 
July 25, 2002, to ABT 109EP-30. On July 29, 2002, ENAC issued AD No. 
2002-384, adopting the requirements of Revision A of this Agusta ABT. 
On October 17, 2002, we issued immediately adopted AD 2002-17-51 (67 FR 
67510, November 6, 2002) to require a reduction in VNE, a 
pilot-check of each T/R blade before each start of the helicopter 
engines, and initial and recurring inspections of each T/R blade for a 
crack.
    Following increased ground vibrations in a Model A 109E helicopter, 
another crack was discovered in a T/R blade, which prompted Agusta to 
issue Revision B, dated November 17, 2002, to ABT 109EP-30. Analysis 
and tests had shown that the fatigue failure of the T/R blade was 
caused by unanticipated loads on the T/R blade. Revision B to that ABT 
specified maintaining the VNE reduction until a new bushing 
was installed in the T/R grip assembly. Further, that ABT established, 
for T/R blade P/N 109-8132-01-111 on grip assembly P/N 109-8131-02-127, 
a retirement life of 200 hours TIS. ENAC adopted the provisions of 
Revision B of the Agusta ABT in ENAC AD No. 2002-592, dated November 
28, 2002.
    On February 14, 2003, we issued AD 2002-25-51, Amendment 39-13060 
(68 FR 9504, February 28, 2003), to require:
    For helicopters with T/R hub and blade assembly, part number (P/N) 
109-8131-02-151 (the T/R hub and blade assembly consists of two T/R 
blades, P/N 109-8132-01-111, and one T/R hub and grip assembly, P/N 
109-8131-02-127):
     Before further flight, installing a placard and marking 
the airspeed indicator to reduce the helicopter VNE by 28 
knots-indicated air speed (KIAS) in addition to any additional 
reduction in VNE caused by optional equipment.
     Before each start of the helicopter engines, allowing an 
owner/operator (pilot) to check the T/R blade for a crack so long as 
the pilot records that AD compliance in the maintenance records in 
accordance with 14 CFR 43.9(a)(1)-(4) and 91.417(a)(2)(v).
     Within 5 hours time-in-service (TIS), and thereafter at 
intervals not to exceed 5 hours TIS, and before further flight any time 
there is an increase in vibration levels, inspecting each T/R blade for 
a crack using a 5x or higher magnifying glass.
     Establishing a new life limit for T/R blade, P/N 109-8132-
01-111, of 200 hours TIS and requiring T/R blades with 190 hours or 
more TIS to be replaced within 10 hours TIS.
     On or before May 31, 2003, modifying and re-identifying 
the T/R hub and grip assembly and the T/R hub and blade assembly, which 
removes the VNE restriction and restores the T/R blade life 
limit to 1,000 hours TIS.
    For helicopters with T/R hub and blade assembly, P/N 109-8131-02-
157 (the T/R hub and blade assembly consists of two T/R blades, P/N 
109-8132-01-111, and one T/R hub and grip assembly, P/N 109-8131-02-
159):
     Before each start of the helicopter engines, allowing an 
owner/operator (pilot) to check the T/R blade for a crack so long as 
the pilot records that AD compliance in the maintenance records in 
accordance with 14 CFR 43.9(a)(1)-(4) and 91.417(a)(2)(v).
     Within 25 hours TIS, and thereafter at intervals not to 
exceed 25 hours TIS, and before further flight any time there is an 
increase in vibration levels, inspecting each T/R blade for a crack 
using a 5x or higher magnifying glass.
     On or before accumulating 150 hours TIS on the T/R hub 
assembly, P/N 109-8131-02-159, and thereafter at intervals not to 
exceed 150 hours TIS, inspecting the bushings, P/N 109-8131-30-109, 
linings for wear, and replacing any unairworthy bushing.
    Also, the existing AD states that T/R blades, P/N 109-8132-01-111, 
which have been operated as part of the T/R hub and blade assembly, P/N 
109-8131-02-151, are considered unairworthy components of the T/R hub 
and blade assembly, P/N 109-8131-02-157, regardless of TIS.
    Finally, AD 2002-25-51 requires replacing any unairworthy T/R blade 
before further flight.

[[Page 12653]]

Actions Since Existing AD Was Issued

    Since we issued AD 2002-25-51, Agusta has issued Revision C, dated 
September 29, 2006, to ABT No. 109EP-30, and states that the service 
experience of T/R hub and blade assemblies with the newly-designed 
bushings that reduce T/R blade loading has shown improvement and has 
determined that increasing the amount of time between inspections is 
appropriate, based upon the service history and the results of the 
maintenance performed.
    In response to Revision C of the ABT, the European Aviation Safety 
Agency (EASA), which is the Technical Agent for the Member States of 
the European Union, has issued EASA AD No. 2006-0353, dated December 4, 
2006, which supersedes ENAC AD 2002-597 to extend the inspection 
interval ``from 150 to 200 FH.'' Subsequently, EASA AD No. 2007-0010, 
dated January 31, 2007, was issued to supersede AD No. 2006-0353 to 
restore the initial requirements of ABT 109EP-30, Revision C, which 
were unintentionally omitted from AD No. 2006-0353.

FAA's Determination

    These helicopters have been approved by the aviation authority of 
Italy and are approved for operation in the United States. Pursuant to 
our bilateral agreement with Italy, EASA, its technical representative, 
has notified us of the unsafe condition described in its AD. We are 
proposing this AD because we evaluated all known relevant information 
and determined that an unsafe condition is likely to exist or develop 
on other products of the same type design.

Related Service Information

    We reviewed ABT No. 109EP-30, Revision C, dated September 29, 2006, 
which describes procedures for checking/inspecting for cracks on both 
the upper and lower surfaces of T/R blades, P/N 109-8132-01-111; 
replacing each bushing, P/N 109-0132-55 and spacer P/N 109-0132-13, 
with bushing, P/N 109-8131-30-109, and instituting a recurring 
inspection of each bushing; and cancelling the VNE 
limitations when the newly-designed bushing is installed on each T/R 
grip assembly, P/N 109-8131-29-101, a ``new'' pair of T/R blades, P/N 
109-8132-01-111, is installed, and the T/R hub-and-grip and hub-and-
blade assemblies are re-identified.

Proposed AD Requirements

    This proposed AD would require:
     Before each start of the helicopter engines, visually 
checking both sides of each T/R blade for a crack. An owner/operator 
(pilot) may perform this check and must enter compliance into the 
aircraft records in accordance with 14 CFR 43.9 (a)(1)-(4) and 14 CFR 
91.417(a)(2)(v). A pilot may perform this check because it involves 
only a visual check for a crack and can be performed equally well by a 
pilot or a mechanic. This procedure is an exception to our standard 
maintenance regulations.
     For helicopters with T/R hub and blade assembly, P/N 109-
8131-02-151, before further flight, modifying each T/R hub and blade 
assembly by installing a new bushing in each grip assembly and two 
zero-TIS T/R blades; and re-identifying the hub and grip assembly and 
the T/R hub and blade assembly with different P/Ns.
     For helicopters with T/R hub and blade assembly, P/N 109-
8131-02-157, within 25 hours TIS and thereafter at intervals not to 
exceed 25 hours TIS, and before further flight any time there is an 
increase in vibration levels, using a 5x or higher power magnifying 
glass, visually inspecting each T/R blade for a crack.
     On or before accumulating 200 hours TIS on the T/R hub and 
grip assembly, and thereafter at intervals not to exceed 200 hours TIS, 
inspecting the linings and measuring the internal diameter of the 
bushings. If the internal diameter of the bushing exceeds 41.35 
millimeters, replacing the bushing.
     If there is a crack, before further flight, replacing the 
T/R blade.
     Revising the Airworthiness Limitations section of the 
maintenance manual to reflect that a T/R blade, P/N 109-8132-01-111, 
which has not been operated as part of T/R hub and blade assembly, P/N 
109-8131-02-151, has a retirement life of 1,000 hours TIS.

Costs of Compliance

    We estimate that this proposed AD would affect 75 helicopters of 
U.S. Registry. Based on an average labor rate of $85 per hour, we 
estimate that operators may incur the following costs in order to 
comply with this AD:
     Visually inspecting the T/R blades would require about 0.5 
work hours for a cost per helicopter of $43 and a total cost to U.S. 
operators of $3,225 per inspection cycle.
     Replacing a cracked T/R blade would require about 2 work 
hours, and required parts would cost about $25,320, for a total cost 
per helicopter of $25,490.
     Modifying the hub assembly with new T/R blades and 
bushings would require about 16 work hours, and required parts would 
cost about $58,690, for a total cost per helicopter of $60,050.
     Inspecting the T/R bushings would require about 7 work 
hours, for a cost per helicopter of $595 and a total cost to U.S. 
operators of $44,625 per inspection cycle.
     Revising the Airworthiness Limitations section of the 
maintenance manual would require about .25 work hour, for a cost per 
helicopter of $22 and a total cost to U.S. operators of $1,650.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more detail the scope of the Agency's 
authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed, I certify this proposed regulation:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979);
    3. Will not affect intrastate aviation in Alaska to the extent that 
it justifies making a regulatory distinction; and
    4. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.
    We prepared an economic evaluation of the estimated costs to comply 
with this proposed AD and placed it in the AD docket.

[[Page 12654]]

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 to read as 
follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by removing Amendment 39-13060 (68 FR 
9504, February 28, 2003), and adding the following new Airworthiness 
Directive (AD):

AGUSTA S.p.A. (Agusta): Docket No. FAA-2013-0146; Directorate 
Identifier 2012-SW-060-AD.

(a) Applicability

    This AD applies to Agusta Model 109E helicopters with tail rotor 
(T/R) hub and blade assembly, part number (P/N) 109-8131-02-151 and 
P/N 109-8131-02-157, certificated in any category.

(b) Unsafe Condition

    This AD defines the unsafe condition as a fatigue crack in a T/R 
blade. This condition could result in failure of the T/R blade and 
subsequent loss of control of the helicopter.

(c) Affected ADs

    This AD supersedes AD 2002-25-51, Docket No. 2002-SW-55-AD, 
Amendment 39-13060 (68 FR 9504, February 28, 2003).

(d) Reserved

(e) Compliance

    You are responsible for performing each action required by this 
AD within the specified compliance time unless it has already been 
accomplished prior to that time.

(f) Required Actions

    (1) Before each start of the helicopter engines, visually check 
both sides of each T/R blade for a crack in the inspection area 
depicted in Figure 1 to paragraph (f) of this AD. This action may be 
performed by the owner/operator (pilot) holding at least a private 
pilot certificate, and must be entered into the aircraft records 
showing compliance with this AD in accordance with 14 CFR 43.9 
(a)(1)-(4) and 14 CFR 91.417(a)(2)(v). The record must be maintained 
as required by 14 CFR 91.173, 121.380, or 135.439.
BILLING CODE 4910-13-P
[GRAPHIC] [TIFF OMITTED] TP25FE13.002

BILLING CODE 4910-03-C
    (2) For helicopters with T/R hub and blade assembly, P/N 109-
8131-02-151 (consisting of two T/R blades, P/N 109-8132-01-111, and 
one T/R hub and grip assembly, P/N 109-8131-02-127), before further 
flight, modify each T/R hub and blade assembly by installing a new 
bushing, P/N 109-8131-30-109, in each grip assembly and two zero-
hour time-in-service (TIS) T/R blades, P/N 109-8132-01-111; re-
identifying the hub and grip assembly as P/N 109-8131-02-159; and 
re-identifying the T/R hub and blade assembly as P/N 109-8131-02-157 
in accordance with the Compliance Instructions, Part V, paragraphs 
2. through 13., of Agusta Bollettino Tecnico No. 109EP-30, Revision 
C, dated September 29, 2006 (BT). A T/R blade, P/N 109-8132-01-111, 
which has been operated as part of T/R hub and blade assembly, P/N 
109-8131-02-151, must be retired regardless of TIS and may not be 
used as part of the T/R hub and blade assembly, P/N 109-8131-02-157. 
Returning the removed T/R blades, grips, or bushings to Agusta is 
not required.
    (3) For helicopters with T/R hub and blade assembly, P/N 109-
8131-02-157 (consisting of two T/R blades, P/N 109-8132-01-111, and 
one T/R hub and grip assembly, P/N 109-8131-02-159), within 25 hours 
TIS, and thereafter at intervals not to exceed 25 hours TIS, and 
before further flight any time there is an increase in vibration 
levels, using a 5x or higher power magnifying glass, visually 
inspect each T/R blade for a crack in accordance with the Compliance 
Instructions, Part III, paragraphs 1. through 5. of the BT. 
Reporting to Agusta is not required.
    (4) On or before accumulating 200 hours TIS on the T/R hub and 
grip assembly, P/N

[[Page 12655]]

109-8131-02-159, and thereafter at intervals not to exceed 200 hours 
TIS, inspect the linings and measure the internal diameter of the 
bushings, P/N 109-8131-30-109, by referring to Figure 2 of the BT. 
If the internal diameter of the bushing exceeds 41.35 millimeters, 
replace the bushing.
    (5) If there is a crack in a T/R blade, before further flight, 
replace the cracked T/R blade.
    (6) Revise the Airworthiness Limitations section of the 
maintenance manual to reflect that a T/R blade, P/N 109-8132-01-111, 
which has not been operated as part of T/R hub and blade assembly, 
P/N 109-8131-02-151, has retirement life of 1,000 hours TIS.

(g) Special Flight Permit

    Special flight permits will not be issued.

(h) Alternative Methods of Compliance (AMOCs)

    (1) The Manager, Safety Management Group, FAA, may approve AMOCs 
for this AD. Send your proposal to: Sharon Miles, Aviation Safety 
Engineer, Regulations and Policy Group, Rotorcraft Directorate, FAA, 
2601 Meacham Blvd., Fort Worth, Texas, 76137; telephone (817) 222-
5110; email sharon.y.miles@faa.gov.
    (2) For operations conducted under a 14 CFR part 119 operating 
certificate or under 14 CFR part 91, subpart K, we suggest that you 
notify your principal inspector, or lacking a principal inspector, 
the manager of the local flight standards district office or 
certificate holding district office before operating any aircraft 
complying with this AD through an AMOC.

(i) Additional Information

    The subject of this AD is addressed in European Aviation Safety 
Agency AD No. 2007-0010, dated January 31, 2007.

 (j) Subject

    Joint Aircraft Service Component (JASC) Code: 6410, Tail Rotor 
Blades.

    Issued in Fort Worth, Texas, on February 11, 2013.
Kim Smith,
Manager, Rotorcraft Directorate, Aircraft Certification Service.
[FR Doc. 2013-04220 Filed 2-22-13; 8:45 am]
BILLING CODE 4910-13-P


