
[Federal Register Volume 77, Number 247 (Wednesday, December 26, 2012)]
[Rules and Regulations]
[Pages 75827-75831]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: 2012-30305]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2012-1228; Directorate Identifier 2012-NM-190-AD; 
Amendment 39-17292; AD 2012-25-11]
RIN 2120-AA64


Airworthiness Directives; The Boeing Company Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule; request for comments.

-----------------------------------------------------------------------

SUMMARY: We are superseding an existing airworthiness directive (AD) 
for certain The Boeing Company Model 757-200, -200CB, and -300 series 
airplanes. That AD currently requires initial and repetitive 
inspections of the fuselage skin and bear strap at the forward, upper 
corner of the L1 entry door cutout for cracking, and repair if 
necessary. That action also provides an optional terminating action for 
the repetitive inspections. That AD also requires additional 
inspections for airplanes having repairs or preventative modifications 
installed and inspections for certain other airplanes. This AD requires 
the previous actions with additional airplane group configurations 
added to paragraph (n) of this AD. This AD was prompted by a 
determination that certain airplane group configurations in paragraph 
(n) of the existing AD were inadvertently removed in the final rule. We 
are issuing this AD to detect and correct cracking of the fuselage skin 
and bear strap at the forward upper corner of the L1 entry door cutout, 
which could result in reduced structural integrity of the L1 entry 
door, and consequent rapid decompression of the airplane.

DATES: This AD is effective January 10, 2013.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in this AD as of October 3, 
2012 (77 FR 52212, August 29, 2012).
    The Director of the Federal Register approved the incorporation by 
reference of a certain other publication listed in this AD as of May 
24, 2004 (69 FR 25481, May 7, 2004).
    We must receive any comments on this AD by February 11, 2013.

ADDRESSES: You may send comments by any of the following methods:
     Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC 20590.
     Hand Delivery: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC 20590, between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays.
    For service information identified in this AD, contact Boeing 
Commercial Airplanes, Attention: Data & Services Management, P. O. Box 
3707, MC 2H-65, Seattle, WA 98124-2207; telephone 206-544-5000, 
extension 1; fax 206-766-5680; Internet https://www.myboeingfleet.com. 
You may review copies of the referenced service information at the FAA, 
Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For 
information on the availability of this material at the FAA, call 425-
227-1221.

Examining the AD Docket

    You may examine the AD docket on the Internet at http://www.regulations.gov; or in person at the Docket Management Facility 
between 9 a.m. and 5 p.m., Monday through Friday, except Federal 
holidays. The AD docket contains this AD, the regulatory evaluation, 
any comments received, and other information. The street address for 
the Docket Office (phone: 800-647-5527) is in the ADDRESSES section. 
Comments will be available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Nancy Marsh, Aerospace Engineer, 
Airframe Branch, ANM-120S, FAA, Seattle Aircraft Certification Office, 
1601 Lind Avenue SW., Renton, WA 98057-3356; phone: 425-917-6440; fax: 
425-917-6590; email: nancy.marsh@faa.gov.

SUPPLEMENTARY INFORMATION:

Discussion

    On July 23, 2012, we issued AD 2012-15-15, Amendment 39-17144 (77 
FR 52212, August 29, 2012), which superseded AD 2004-09-32, Amendment 
39-13622 (69 FR 25481, May 7, 2004), for certain The Boeing Company 
Model 757-200, -200CB, and -300 series airplanes. AD 2012-15-15 
requires initial and repetitive inspections of the fuselage skin and 
bear strap at the forward, upper corner of the L1 entry door cutout for 
cracking, and repair if necessary. That action also provides an 
optional terminating action for the repetitive inspections. That AD 
also requires additional inspections for airplanes having repairs or 
preventative modifications installed and inspections for certain other 
airplanes. That AD resulted from reports of additional cracking in the 
fuselage skin. We issued that AD to detect and correct cracking of the 
fuselage skin and bear strap at the forward upper corner of the L1 
entry door cutout, which could result in reduced structural integrity 
of the L1 entry door, and consequent rapid decompression of the 
airplane.

Actions Since AD Was Issued

    Since we issued AD 2012-15-15, Amendment 39-17144 (77 FR 52212, 
August 29, 2012), it was noted that certain airplane group 
configurations included in paragraph (n) of the NPRM were inadvertently 
removed in the final rule. This AD includes Group 1, Configuration 4, 
and Group 2, Configuration 3, in paragraph (n) of this AD.

FAA's Determination

    We are issuing this AD because we evaluated all the relevant 
information and determined the unsafe condition described previously is 
likely to exist or develop in other products of the same type design.

AD Requirements

    This AD requires retaining all requirements of AD 2012-15-15, 
Amendment 39-17144 (77 FR 52212, August 29, 2012).

FAA's Justification and Determination of the Effective Date

    An unsafe condition exists that requires the immediate adoption of 
this AD. The FAA has found that the risk to the flying public justifies 
waiving notice and comment prior to adoption of this

[[Page 75828]]

rule because all actions of AD 2012-15-15, Amendment 39-17144 (77 FR 
52212, August 29, 2012), are retained and include certain airplane 
group configurations in paragraph (n) of this AD that were specified in 
the NPRM (76 FR 81890, December 29, 2011), but were inadvertently 
removed in the final rule of AD 2012-15-15. Therefore, we find that 
notice and opportunity for prior public comment are unnecessary and 
that good cause exists for making this amendment effective in less than 
30 days.

Comments Invited

    This AD is a final rule that involves requirements affecting flight 
safety, and we did not provide you with notice and an opportunity to 
provide your comments before it becomes effective. However, we invite 
you to send any written data, views, or arguments about this AD. Send 
your comments to an address listed under the ADDRESSES section. Include 
the docket number FAA-2012-1228 and directorate identifier 2012-NM-190-
AD at the beginning of your comments. We specifically invite comments 
on the overall regulatory, economic, environmental, and energy aspects 
of this AD. We will consider all comments received by the closing date 
and may amend this AD because of those comments.
    We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this AD.

Costs of Compliance

    We estimate that this AD affects 591 airplanes of U.S. registry.
    We estimate the following costs to comply with this AD:

                                                                     Estimated Costs
--------------------------------------------------------------------------------------------------------------------------------------------------------
                                                                                          Number of
                                          Work-    Average                                  U.S.-
                 Action                   hours   labor rate      Cost per airplane       registered                      Fleet cost
                                                   per hour                               airplanes
--------------------------------------------------------------------------------------------------------------------------------------------------------
Inspections (retained actions from            2          $85  $170 per inspection cycle           57  $9,690 per inspection cycle.
 existing AD 2012[dash]15[dash]15,
 Amendment 39[dash]17144 (77 FR 52212,
 August 29, 2012)).
Inspection (retained actions from             3          $85  $255 per inspection cycle          591  $150,705 per inspection cycle.
 existing AD 2012-15-15, Amendment
 39[dash]17144 (77 FR 52212, August 29,
 2012)).
Supplemental inspection (retained            15          $85  $1,275 per inspection              591  $753,525 per inspection cycle.
 actions from existing AD 2012-15-15,                          cycle.
 Amendment 39[dash]17144 (77 FR 52212,
 August 29, 2012)).
--------------------------------------------------------------------------------------------------------------------------------------------------------

    We estimate the following costs to do any necessary repairs that 
would be required based on the results of the inspections. We have no 
way of determining the number of aircraft that might need these 
repairs:

                                                                   On-condition Costs
--------------------------------------------------------------------------------------------------------------------------------------------------------
                Action                         Labor cost                Parts cost                               Cost per product
--------------------------------------------------------------------------------------------------------------------------------------------------------
Repair (retained actions from          Up to 26 work-hours x $85   Up to $2,661..........  Up to $4,871 depending on configuration.
 existing AD 2012[dash]15-15,           = Up to $2,210.
 Amendment 39[dash]17144 (77 FR
 52212, August 29, 2012)).
Preventive modification (retained      18 work-hours x $85 =       $1,338................  $2,868
 actions from existing AD 2012-15-15,   $1,530.
 Amendment 39[dash]17144 (77 FR
 52212, August 29, 2012)).
--------------------------------------------------------------------------------------------------------------------------------------------------------

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, Section 106, describes the 
authority of the FAA Administrator. Subtitle VII, Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701, ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    This AD will not have federalism implications under Executive Order 
13132. This AD will not have a substantial direct effect on the States, 
on the relationship between the national government and the States, or 
on the distribution of power and responsibilities among the various 
levels of government.
    For the reasons discussed above, I certify that this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Is not a ``significant rule'' under DOT Regulatory Policies and 
Procedures (44 FR 11034, February 26, 1979),
    (3) Will not affect intrastate aviation in Alaska, and
    (4) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

[[Page 75829]]

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends part 39 of the Federal Aviation 
Regulations (14 CFR part 39) as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by removing airworthiness directive (AD) 
2012-15-15, Amendment 39-17144 (77 FR 52212, August 29, 2012), and 
adding the following new AD:

2012-25-11 The Boeing Company: Amendment 39-17292; Docket No. FAA-
2012-1228; Directorate Identifier 2012-NM-190-AD.

(a) Effective Date

    This AD is effective January 10, 2013.

(b) Affected ADs

    This AD supersedes AD 2012-15-15, Amendment 39-17144 (77 FR 
52212, August 29, 2012).

(c) Applicability

    This AD applies to all The Boeing Company Model 757-200, -200CB, 
and -300 series airplanes, certificated in any category. Model 757-
200PF series airplanes are not affected by this AD.

(d) Subject

    Joint Aircraft System Component (JASC)/Air Transport Association 
(ATA) of America Code 53: Fuselage.

(e) Unsafe Condition

    This AD was prompted by reports of cracks in the fuselage skin 
and bear strap at the forward upper corner of the L1 entry door 
cutout. We are issuing this AD to detect and correct cracking of the 
fuselage skin and bear strap at the forward, upper corner of the L1 
entry door cutout, which could result in reduced structural 
integrity of the L1 entry door and consequent rapid decompression of 
the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Retained Initial Inspection With Terminating Action

    This paragraph restates the requirements of paragraph (g) of AD 
2012-15-15, Amendment 39-17144 (77 FR 52212, August 29, 2012), with 
a terminating action. For airplanes having line numbers 1 through 90 
inclusive: Within 500 flight cycles after May 24, 2004 (the 
effective date of AD 2004-09-32, Amendment 39-13622 (69 FR 25481, 
May 7, 2004)), or within 90 days after May 24, 2004 (the effective 
date of AD 2004-09-32), whichever occurs later, do the inspections 
of the forward upper corner of the L1 entry door cutout specified in 
paragraphs (g)(1), (g)(2), and (g)(3) of this AD, per Part 1 of the 
Work Instructions of Boeing Special Attention Service Bulletin 757-
53-0089, dated March 18, 2004, until the initial inspection required 
by paragraph (k) of this AD has been done. Doing the repair 
specified in paragraph (i) or (l) of this AD, or doing the 
preventive modification specified in paragraph (j) of this AD, 
terminates the inspections required by this paragraph.
    (1) Do a high frequency eddy current (HFEC) inspection for 
cracking of the fuselage skin around the adjacent fasteners.
    (2) Do an HFEC inspection for cracking along the edge of the 
skin and bear strap.
    (3) Do a low frequency eddy current (LFEC) inspection for 
cracking of the bear strap around each fastener.

(h) Retained Repetitive Inspections and Terminating Modification When 
No Crack Is Detected

    This paragraph restates the requirements of paragraph (h) of AD 
2012-15-15, Amendment 39-17144 (77 FR 52212, August 29, 2012), with 
a terminating modification. If no crack is detected during any 
inspection required by paragraph (g) of this AD: Repeat the 
inspections required by paragraph (g) of this AD at intervals not to 
exceed 1,400 flight cycles, until the requirements of paragraph (k) 
of this AD are done. Doing the repair specified in paragraph (i) or 
(l) of this AD, or doing the preventive modification specified in 
paragraph (j) of this AD, as applicable, terminates the repetitive 
inspections required by this paragraph.

(i) Retained Repair, With Repair Option When Any Crack Is Detected

    This paragraph restates the requirements of paragraph (i) of AD 
2012-15-15, Amendment 39-17144 (77 FR 52212, August 29, 2012), with 
a repair option. If any crack is detected during any inspection 
required by paragraph (g) or (h) of this AD, and Boeing Special 
Attention Service Bulletin 757-53-0089, dated March 18, 2004, 
specifies to contact Boeing for appropriate action: Before further 
flight, repair, in accordance with a method approved by the Manager, 
Seattle Aircraft Certification Office (ACO), FAA; or in accordance 
with data meeting the type certification basis of the airplane 
approved by the Boeing Commercial Airplanes Organization Designation 
Authorization (ODA) that has been authorized by the Manager, Seattle 
ACO, to make such findings; or using a method approved in accordance 
with the procedures specified in paragraph (r) of this AD. For a 
repair method to be approved, the approval must specifically 
reference this AD. Doing the repair terminates the inspections 
required by paragraphs (g) and (h) of this AD.

(j) Retained Optional Preventive Modification

    This paragraph restates the optional preventive modification 
specified in paragraph (j) of AD 2012-15-15, Amendment 39-17144 (77 
FR 52212, August 29, 2012). As an alternative to accomplishing the 
inspections required by paragraphs (g) and (h) of this AD, do the 
optional preventative modification of the forward upper corner of 
the L1 entry door cutout, and do all applicable related 
investigative/corrective actions, by accomplishing all the actions 
specified in Part 2 of the Work Instructions of Boeing Special 
Attention Service Bulletin 757-53-0089, dated March 18, 2004. 
Accomplishment of the modification constitutes terminating action 
for the inspections required by paragraphs (g) and (h) of this AD.

(k) Retained Inspections

    This paragraph restates the requirements of paragraph (k) of AD 
2012-15-15, Amendment 39-17144 (77 FR 52212, August 29, 2012). For 
airplanes in Group 1, Configurations 1 and 2, and Group 2, 
Configuration 1, as defined in Boeing Special Attention Service 
Bulletin 757-53-0094, Revision 1, dated August 12, 2009: Except as 
provided by paragraph (p)(1) of this AD, at the applicable times 
specified in paragraph 1.E, ``Compliance,'' of Boeing Special 
Attention Service Bulletin 757-53-0094, Revision 1, dated August 12, 
2009, do HFEC and LFEC inspections for cracking of the skin and bear 
strap at the forward upper corner of the L1 entry door cutout, in 
accordance with the Accomplishment Instructions of Boeing Special 
Attention Service Bulletin 757-53-0094, Revision 1, dated August 12, 
2009, except as provided by paragraph (p) of this AD. Repeat the 
inspections thereafter at intervals not to exceed 1,400 flight 
cycles. Doing the initial inspection required by this paragraph 
terminates the inspections required by paragraphs (g) and (h) of 
this AD. Doing the repair specified in paragraph (l) of this AD, or 
doing the optional preventive modification specified in paragraph 
(m) of this AD, terminates the inspections required by this 
paragraph.

(l) Retained Terminating Repair

    This paragraph restates the terminating repair specified in 
paragraph (l) of AD 2012-15-15, Amendment 39-17144 (77 FR 52212, 
August 29, 2012). If any cracking is found during any inspection 
required by paragraph (k) of this AD, before further flight, repair 
in accordance with the Accomplishment Instructions of Boeing Special 
Attention Service Bulletin 757-53-0094, Revision 1, dated August 12, 
2009, except as required by paragraph (p) of this AD. Doing the 
repair terminates the repetitive inspections required by paragraph 
(k) of this AD.

(m) Retained Optional Preventive Modification

    This paragraph restates the optional preventive modification 
specified in paragraph (m) of AD 2012-15-15, Amendment 39-17144 (77 
FR 52212, August 29, 2012). Accomplishing the optional preventive 
modification, in accordance with

[[Page 75830]]

the Accomplishment Instructions of Boeing Special Attention Service 
Bulletin 757-53-0094, Revision 1, dated August 12, 2009, except as 
provided by paragraph (p) of this AD, terminates the repetitive 
inspections required by paragraph (k) of this AD.

(n) Retained Inspections and Repair With New Airplane Group 
Configurations

    This paragraph restates the requirements of paragraph (n) of AD 
2012-15-15, Amendment 39-17144 (77 FR 52212, August 29, 2012), with 
new airplane group configurations. For airplanes in Group 1, 
Configurations 3, 4, and 5; and Group 2, Configurations 2, 3, and 4; 
as identified in Boeing Special Attention Service Bulletin 757-53-
0094, Revision 1, dated August 12, 2009; with a repair doubler; a 
doubler and a tripler; or a doubler, tripler, and quadrupler 
installed; or with a preventive modification doubler installed: At 
the applicable times specified in paragraph 1.E, ``Compliance,'' of 
Boeing Special Attention Service Bulletin 757-53-0094, Revision 1, 
dated August 12, 2009, except as required by paragraph (p)(2) of 
this AD, do LFEC, HFEC, and detailed inspections, as applicable, for 
cracking of the doubler, tripler, quadrupler, skin, bear strap, and 
inner chord strap, as applicable, in accordance with the 
Accomplishment Instructions of Boeing Special Attention Service 
Bulletin 757-53-0094, Revision 1, dated August 12, 2009. Repeat the 
inspections thereafter at the applicable times specified in 
paragraph 1.E., ``Compliance,'' of Boeing Special Attention Service 
Bulletin 757-53-0094, Revision 1, dated August 12, 2009.

(o) Retained Repair

    This paragraph restates the requirements of paragraph (o) of AD 
2012-15-15, Amendment 39-17144 (77 FR 52212, August 29, 2012). If 
any cracking is found during any inspection required by paragraph 
(n) of this AD, before further flight, repair the crack in 
accordance with the procedures specified in paragraph (r) of this 
AD.

(p) Retained Exceptions to Service Bulletin Specifications

    This paragraph restates the exceptions specified in paragraph 
(p) of AD 2012-15-15, Amendment 39-17144 (77 FR 52212, August 29, 
2012). The following exceptions apply to this AD.
    (1) Where Boeing Special Attention Service Bulletin 757-53-0094, 
Revision 1, dated August 12, 2009, specifies a compliance time after 
the ``original issue date'' or ``Revision 1 date of the service 
bulletin,'' this AD requires compliance within the specified 
compliance time after October 3, 2012 (the effective date of AD 
2012-15-15, Amendment 39-17144 (77 FR 52212, August 29, 2012)).
    (2) Where Boeing Special Attention Service Bulletin 757-53-0094, 
Revision 1, dated August 12, 2009, specifies doing the HFEC, LFEC, 
and detailed inspections required by paragraph (n) of this AD before 
the accumulation of 37,500 total flight cycles, this AD requires the 
inspections to be accomplished at the latest of the times specified 
in paragraphs (p)(2)(i), (p)(2)(ii), and (p)(2)(iii) of this AD.
    (i) Before the accumulation of 37,500 total flight cycles.
    (ii) Within 24 months after October 3, 2012 (the effective date 
of AD 2012-15-15, Amendment 39-17144 (77 FR 52212, August 29, 
2012)).
    (iii) Within 4,000 flight cycles since installation of a repair 
doubler; a doubler and a tripler; or a doubler, tripler, and 
quadrupler; or on which a preventive modification doubler is 
installed; in accordance with the Accomplishment Instructions of 
Boeing Special Attention Service Bulletin 757-53-0094, Revision 1, 
dated August 12, 2009; or in accordance with paragraph (h) of this 
AD.
    (3) Where Boeing Special Attention Service Bulletin 757-53-0094, 
Revision 1, dated August 12, 2009, specifies contacting Boeing for 
repair instructions, this AD requires repairing in accordance with 
the procedures specified in paragraph (r) of this AD.
    (4) Where Boeing Special Attention Service Bulletin 757-53-0094, 
Revision 1, dated August 12, 2009, specifies a specific fastener and 
material to be used for accomplishing a repair, this AD allows the 
substitution of fastener and material, as specified in Chapter 51 of 
the Boeing 757 Structural Repair Manual.
    (5) Where Boeing Special Attention Service Bulletin 757-53-0094, 
Revision 1, dated August 12, 2009, specifies a specific fastener 
grip length, this AD allows substitution of a fastener grip length, 
as specified in Chapter 51 of the Boeing 757 Structural Repair 
Manual.
    (6) If it is necessary to remove more parts for access, those 
parts may be removed. If access is possible without removing 
identified parts, it is not necessary to remove all of the 
identified parts.

(q) Retained Credit for Previous Actions

    This paragraph restates the credit provisions specified in 
paragraph (q) of AD 2012-15-15, Amendment 39-17144 (77 FR 52212, 
August 29, 2012). For airplanes in Group 1, Configurations 1 and 2; 
and Group 2, Configuration 1; as defined in Boeing Special Attention 
757-53-0094, Revision 1, dated August 12, 2009: This paragraph 
provides credit for the actions required by paragraph (k) of this 
AD, if those actions were performed before October 3, 2012 (the 
effective date of AD 2012-15-15), using Boeing Special Attention 
Service Bulletin 757-53-0094, dated January 16, 2008; or Boeing 
Special Attention Service Bulletin 757-53-0089, dated March 18, 2004 
(which are not incorporated by reference in this AD).

(r) Alternative Methods of Compliance (AMOCs)

    (1) The Manager, Seattle ACO, FAA, has the authority to approve 
AMOCs for this AD, if requested using the procedures found in 14 CFR 
39.19. In accordance with 14 CFR 39.19, send your request to your 
principal inspector or local Flight Standards District Office, as 
appropriate. If sending information directly to the ACO, send it to 
ATTN: Nancy Marsh, Aerospace Engineer, Airframe Branch, ANM-120S, 
FAA, 1601 Lind Avenue SW., Renton, WA 98057-3356; phone: 425-917-
6440; fax: 425-917-6432; email: nancy.marsh@faa.gov.
    (2) Before using any approved AMOC, notify your appropriate 
principal inspector, or lacking a principal inspector, the manager 
of the local flight standards district office/certificate holding 
district office.
    (3) An AMOC that provides an acceptable level of safety may be 
used for any repair required by this AD if it is approved by the 
Boeing Commercial Airplanes ODA that has been authorized by the 
Manager, Seattle ACO to make those findings. For a repair method to 
be approved, the repair must meet the certification basis of the 
airplane, and the approval must specifically refer to this AD.
    (4) AMOCs previously approved in accordance with AD 2004-09-32, 
Amendment 39-13622 (69 FR 25481, May 7, 2004), are approved as AMOCs 
for the corresponding actions specified in paragraphs (g), (h), and 
(i) of this AD.
    (5) AMOCs previously approved in accordance with AD 2012-15-15, 
Amendment 39-17144 (77 FR 52212, August 29, 2012)), are approved as 
AMOCs for the corresponding actions specified in this AD.

(s) Related Information

    (1) For more information about this AD, contact Nancy Marsh, 
Aerospace Engineer, Airframe Branch, ANM-120S, FAA, 1601 Lind Avenue 
SW., Renton, WA 98057-3356; phone: 425-917-6440; fax: 425-917-6432; 
email: nancy.marsh@faa.gov.
    (2) For service information identified in this AD, contact 
Boeing Commercial Airplanes, Attention: Data & Services Management, 
P.O. Box 3707, MC 2H-65, Seattle, WA 98124-2207; telephone 206-544-
5000, extension 1; fax 206-766-5680; Internet https://www.myboeingfleet.com.

(t) Material Incorporated by Reference

    (1) The Director of the Federal Register approved the 
incorporation by reference (IBR) of the service information listed 
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) You must use this service information as applicable to do 
the actions required by this AD, unless the AD specifies otherwise.
    (3) The following service information was approved for IBR on 
October 3, 2012 (77 FR 52212, August 29, 2012).
    (i) Boeing Special Attention Service Bulletin 757-53-0094, 
Revision 1, dated August 12, 2009.
    (ii) Reserved.
    (4) The following service information was approved for IBR on 
May 24, 2004 (69 FR 25481, May 7, 2004).
    (i) Boeing Special Attention Service Bulletin 757-53-0089, dated 
March 18, 2004.
    (ii) Reserved.
    (5) For service information identified in this AD, contact 
Boeing Commercial Airplanes, Attention: Data & Services Management, 
P.O. Box 3707, MC 2H-65, Seattle, WA 98124-2207; telephone 206-544-
5000, extension 1; fax 206-766-5680; Internet https://www.myboeingfleet.com.
    (6) You may review copies of the service information at the FAA, 
Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. 
For information on the availability of this material at the FAA, 
call 425-227-1221.
    (7) You may also review copies of the service information that 
is incorporated by

[[Page 75831]]

reference at the National Archives and Records Administration 
(NARA). For information on the availability of this material at 
NARA, call 202-741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued in Renton, Washington, on December 5, 2012.
Kalene C. Yanamura,
Acting Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2012-30305 Filed 12-21-12; 8:45 am]
BILLING CODE 4910-13-P


