
[Federal Register Volume 77, Number 200 (Tuesday, October 16, 2012)]
[Proposed Rules]
[Pages 63281-63282]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: 2012-25453]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2012-1072; Directorate Identifier 2012-NM-141-AD]
RIN 2120-AA64


Airworthiness Directives; Bombardier, Inc. Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to adopt a new airworthiness directive (AD) for 
certain Bombardier, Inc. Model CL-600-2B19 (Regional Jet Series 100 & 
440) airplanes. This proposed AD was prompted by reports of two in-
service incidents where the left main landing gear (MLG) failed to 
extend. This proposed AD would require installing stopper plates on the 
aft uplock frames in the MLG bay adjacent to the right and left MLG 
uplock assemblies. We are proposing this AD to prevent incorrect 
installation of the upper bolt in the MLG uplock assembly, which could 
prevent the MLG from extending and adversely affect the safe landing of 
the airplane.

DATES: We must receive comments on this proposed AD by November 30, 
2012.

ADDRESSES: You may send comments by any of the following methods:
     Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: (202) 493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC 20590.
     Hand Delivery: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC, between 9 a.m. and 5 p.m., Monday 
through Friday, except Federal holidays.
    For service information identified in this proposed AD, contact 
Bombardier, Inc., 400 C[ocirc]te-Vertu Road West, Dorval, Qu[eacute]bec 
H4S 1Y9, Canada; telephone 514-855-5000; fax 514-855-7401; email 
thd.crj@aero.bombardier.com; Internet http://www.bombardier.com. You 
may review copies of the referenced service information at the FAA, 
Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For 
information on the availability of this material at the FAA, call 425-
227-1221.

Examining the AD Docket

    You may examine the AD docket on the Internet at http://www.regulations.gov; or in person at the Docket Operations office 
between 9 a.m. and 5 p.m., Monday through Friday, except Federal 
holidays. The AD docket contains this proposed AD, the regulatory 
evaluation, any comments received, and other information. The street 
address for the Docket Operations office (telephone (800) 647-5527) is 
in the ADDRESSES section. Comments will be available in the AD docket 
shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Cesar Gomez, Aerospace Engineer, 
Airframe and Mechanical Systems Branch, ANE-171, FAA, New York Aircraft 
Certification Office (ACO), 1600 Stewart Avenue, Suite 410, Westbury, 
New York 11590; phone: 516-228-7328; fax: 516-794-5531.

SUPPLEMENTARY INFORMATION: 

Comments Invited

    We invite you to send any written relevant data, views, or 
arguments about this proposed AD. Send your comments to an address 
listed under the ADDRESSES section. Include ``Docket No. FAA-2012-1072; 
Directorate Identifier 2012-NM-141-AD'' at the beginning of your 
comments. We specifically invite comments on the overall regulatory, 
economic, environmental, and energy aspects of this proposed AD. We 
will consider all comments received by the closing date and may amend 
this proposed AD based on those comments.
    We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this proposed AD.

Discussion

    Transport Canada Civil Aviation (TCCA), which is the aviation 
authority for Canada, has issued Canadian Airworthiness Directive CF-
2012-22, dated July 24, 2012 (referred to after this as ``the MCAI''), 
to correct an unsafe condition for the specified products. The MCAI 
states:

There have been two reported in-service incidents where the left 
main landing gear (MLG) failed to extend. The investigation revealed 
that in both cases, the uplock assembly had been replaced prior to 
the in-service incidents and the upper bolt of the uplock assembly 
was incorrectly installed. The incorrect installation of the upper 
bolt resulted in the uplock assembly pivoting on the lower 
attachment bolt and preventing the MLG from extending under normal 
or alternate extension
The potential for an incorrect installation of the upper bolt could 
occur at both the left hand side (LHS) and/or the right hand side 
(RHS) MLG uplock assembly. Failure of the MLG to extend could 
adversely affect the safe landing of the aeroplane.
This [Canadian] AD mandates the installation of stopper plates on 
the aft uplock frames in the MLG bay, adjacent to both the RHS and 
LHS MLG uplock assemblies, to prevent an incorrect installation of 
the MLG uplock assembly.

You may obtain further information by examining the MCAI in the AD 
docket.

Relevant Service Information

    Bombardier, Inc. has issued Service Bulletin 601R-32-109, dated May 
29, 2012. The actions described in this service information are 
intended to correct the unsafe condition identified in the MCAI.

FAA's Determination and Requirements of This Proposed AD

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to our bilateral agreement with the State of Design Authority, we have 
been notified of the unsafe condition described in the MCAI and service 
information referenced above. We are proposing this AD because we 
evaluated all pertinent information and determined an unsafe condition 
exists and is likely to exist or develop on other products of the same 
type design.

Costs of Compliance

    Based on the service information, we estimate that this proposed AD 
would affect about 574 products of U.S. registry. We also estimate that 
it would take about 5 work-hours per product to comply with the basic 
requirements of this proposed AD. The average labor rate is $85 per 
work-hour. Based on these figures, we estimate the cost of the proposed 
AD on U.S. operators to be $243,950, or $425 per product.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more

[[Page 63282]]

detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979);
    3. Will not affect intrastate aviation in Alaska; and
    4. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.
    We prepared a regulatory evaluation of the estimated costs to 
comply with this proposed AD and placed it in the AD docket.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

    1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

    2. The FAA amends Sec.  39.13 by adding the following new AD:

Bombardier, Inc.: Docket No. FAA-2012-1072; Directorate Identifier 
2012-NM-141-AD.

(a) Comments Due Date

    We must receive comments by November 30, 2012.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Bombardier, Inc. Model CL-600-2B19 (Regional 
Jet Series 100 & 440) airplanes, certificated in any category, 
serial numbers 7003 through 7990 inclusive, and 8000 through 8999 
inclusive.

(d) Subject

    Air Transport Association (ATA) of America Code 32, Landing 
gear.

(e) Reason

    This AD was prompted by reports of two in-service incidents 
where the left main landing gear (MLG) failed to extend. We are 
issuing this AD to prevent incorrect installation of the upper bolt 
in the MLG uplock assembly, which could prevent the MLG from 
extending and adversely affect the safe landing of the airplane.

(f) Compliance

    You are responsible for having the actions required by this AD 
performed within the compliance times specified, unless the actions 
have already been done.

(g) Installation of Stopper Plates

    Within 5,500 flight hours or 48 months after the effective date 
of this AD, whichever occurs first: Install stopper plates on the 
aft uplock frame of both the right and left MLG uplock assemblies, 
in accordance with the Accomplishment Instructions of Bombardier 
Service Bulletin 601R-32-109, dated May 29, 2012.

(h) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, New 
York Aircraft Certification Office (ACO), ANE-170, FAA, has the 
authority to approve AMOCs for this AD, if requested using the 
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, 
send your request to your principal inspector or local Flight 
Standards District Office, as appropriate. If sending information 
directly to the ACO, send it to ATTN: Program Manager, Continuing 
Operational Safety, FAA, New York ACO, 1600 Stewart Avenue, Suite 
410, Westbury, NY 11590; telephone 516-228-7300; fax 516-794-5531. 
Before using any approved AMOC, notify your appropriate principal 
inspector, or lacking a principal inspector, the manager of the 
local flight standards district office/certificate holding district 
office. The AMOC approval letter must specifically reference this 
AD.
    (2) Airworthy Product: For any requirement in this AD to obtain 
corrective actions from a manufacturer or other source, use these 
actions if they are FAA-approved. Corrective actions are considered 
FAA-approved if they are approved by the State of Design Authority 
(or their delegated agent). You are required to assure the product 
is airworthy before it is returned to service.

(i) Related Information

    (1) Refer to MCAI Canadian Airworthiness Directive CF-2012-22, 
dated July 24, 2012; and Bombardier Service 601R-32-109, dated May 
29, 2012; for related information.
    (2) For service information identified in this AD, contact 
Bombardier, Inc., 400 C[ocirc]te-Vertu Road West, Dorval, 
Qu[eacute]bec H4S 1Y9, Canada; telephone 514-855-5000; fax 514 855-
7401; email thd.crj@aero.bombardier.com; Internet http://www.bombardier.com. You may review copies of the referenced service 
information at the FAA, Transport Airplane Directorate, 1601 Lind 
Avenue SW., Renton, WA. For information on the availability of this 
material at the FAA, call 425-227-1221.


    Issued in Renton, Washington, on October 4, 2012.
Dionne Palermo,
Acting Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2012-25453 Filed 10-15-12; 8:45 am]
BILLING CODE 4910-13-P


