
[Federal Register Volume 77, Number 191 (Tuesday, October 2, 2012)]
[Proposed Rules]
[Pages 60073-60075]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: 2012-24173]



[[Page 60073]]

-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2012-1032; Directorate Identifier 2012-NM-079-AD]
RIN 2120-AA64


Airworthiness Directives; Saab AB, Saab Aerosystems Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to adopt a new airworthiness directive (AD) for all 
Saab AB, Saab Aerosystems Model SAAB 2000 airplanes. This proposed AD 
was prompted by reports of chafing on the bottom panel of the center 
cabin. This proposed AD would require doing a general visual inspection 
to determine if certain fasteners are installed, and related 
investigative and corrective actions. We are proposing this AD to 
detect and correct any chafing on the bottom panel of the center cabin, 
which could affect the structural integrity of the affected wing-to-
fuselage connection.

DATES: We must receive comments on this proposed AD by November 16, 
2012.

ADDRESSES: You may send comments by any of the following methods:
     Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: (202) 493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC 20590.
     Hand Delivery: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC, between 9 a.m. and 5 p.m., Monday 
through Friday, except Federal holidays.
    For service information identified in this proposed AD, contact 
Saab AB, Saab Aeronautics, SE-581 88, Link[ouml]ping, Sweden; telephone 
+46 13 18 5591; fax +46 13 18 4874; email 
saab2000.techsupport@saabgroup.com; Internet http://www.saabgroup.com. 
You may review copies of the referenced service information at the FAA, 
Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For 
information on the availability of this material at the FAA, call 425-
227-1221.

Examining the AD Docket

    You may examine the AD docket on the Internet at http://www.regulations.gov; or in person at the Docket Operations office 
between 9 a.m. and 5 p.m., Monday through Friday, except Federal 
holidays. The AD docket contains this proposed AD, the regulatory 
evaluation, any comments received, and other information. The street 
address for the Docket Operations office (telephone (800) 647-5527) is 
in the ADDRESSES section. Comments will be available in the AD docket 
shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Shahram Daneshmandi, Aerospace 
Engineer, International Branch, ANM-116, Transport Airplane 
Directorate, FAA, 1601 Lind Avenue SW., Renton, WA 98057-3356; 
telephone 425-227-1112; fax 425-227-1149.

SUPPLEMENTARY INFORMATION: 

Comments Invited

    We invite you to send any written relevant data, views, or 
arguments about this proposed AD. Send your comments to an address 
listed under the ADDRESSES section. Include ``Docket No. FAA-2012-1032; 
Directorate Identifier 2012-NM-079-AD'' at the beginning of your 
comments. We specifically invite comments on the overall regulatory, 
economic, environmental, and energy aspects of this proposed AD. We 
will consider all comments received by the closing date and may amend 
this proposed AD based on those comments.
    We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this proposed AD.

Discussion

    The European Aviation Safety Agency (EASA), which is the Technical 
Agent for the Member States of the European Community, has issued EASA 
Airworthiness Directive 2012-0068, dated April 25, 2012 (referred to 
after this as ``the MCAI''), to correct an unsafe condition for the 
specified products. The MCAI states:

    On two SAAB 2000 aeroplanes, signs of chafing have been found on 
the bottom panel of the centre cabin between fuselage station (STA) 
562 and STA 622. The investigation results have shown that the 
chafing is caused by certain Hi Lok fasteners, installed as a repair 
during production, through the upper wing skin panel.
    This condition, if not detected and corrected, could affect the 
structural integrity of the affected wing-to-fuselage connection.
    To address this potential unsafe condition, SAAB issued Service 
Bulletin (SB) 2000-53-057 to provide instructions for a general 
visual inspection to detect chafing in the area between the upper 
wing skin and the cabin centre bottom panel and to verify if there 
are Hi Lok fasteners installed with the collar up.
    For the reasons described above, this [EASA] AD requires a one-
time inspection of the designated area, the accomplishment of 
corrective action(s) [repair], depending on findings, and the 
reporting of all inspection results * * *.
    This [EASA] AD is considered an interim action and further AD 
action may follow.

Related investigative actions include measuring the distance between 
the fastener and bottom panel and a boroscope inspection for chafing 
and damage of the bottom panel. You may obtain further information by 
examining the MCAI in the AD docket.

Relevant Service Information

    Saab AB, Saab Aerosystems has issued Service Bulletin 2000-53-057, 
dated November 22, 2011. The actions described in this service 
information are intended to correct the unsafe condition identified in 
the MCAI.

FAA's Determination and Requirements of This Proposed AD

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to our bilateral agreement with the State of Design Authority, we have 
been notified of the unsafe condition described in the MCAI and service 
information referenced above. We are proposing this AD because we 
evaluated all pertinent information and determined an unsafe condition 
exists and is likely to exist or develop on other products of the same 
type design.

Differences Between This AD and the MCAI or Service Information

    Saab Service Bulletin 2000-53-057, dated November 22, 2011, 
specifies to contact the manufacturer for repair instructions, but this 
proposed AD would require doing the repair using a method that we 
approve.

Costs of Compliance

    Based on the service information, we estimate that this proposed AD 
would affect about 10 products of U.S. registry. We also estimate that 
it would take about 4 work-hours per product to comply with the basic 
requirements of this proposed AD. The average labor rate is $85 per 
work-hour. Based on these figures, we estimate the cost of the proposed 
AD on U.S. operators to be $3,400, or $340 per product.

[[Page 60074]]

    We have received no definitive data that would enable us to provide 
a cost estimate for the on-condition actions specified in this proposed 
AD.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more detail the scope of the Agency's 
authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979);
    3. Will not affect intrastate aviation in Alaska; and
    4. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.
    We prepared a regulatory evaluation of the estimated costs to 
comply with this proposed AD and placed it in the AD docket.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

    1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

    2. The FAA amends Sec.  39.13 by adding the following new AD:

Saab AB, Saab Aerosystems: Docket No. FAA-2012-1032; Directorate 
Identifier 2012-NM-079-AD.

(a) Comments Due Date

    We must receive comments by November 16, 2012.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Saab AB, Saab Aerosystems Model SAAB 2000 
airplanes, certificated in any category, all serial numbers.

(d) Subject

    Air Transport Association (ATA) of America Code 53, Fuselage.

(e) Reason

    This AD was prompted by reports of chafing on the bottom panel 
of the center cabin. We are issuing this AD to detect and correct 
any chafing on the bottom panel of the center cabin, which could 
affect the structural integrity of the affected wing-to-fuselage 
connection.

(f) Compliance

    You are responsible for having the actions required by this AD 
performed within the compliance times specified, unless the actions 
have already been done.

(g) Inspection

    Within 12 months after the effective date of this AD, do a 
general visual inspection of the area between the upper part of the 
wing skin and the center bottom panel to determine if any Hi Lok 
fasteners are installed with the collar up, and do all applicable 
related investigative actions, in accordance with the Accomplishment 
Instructions of Saab Service Bulletin 2000-53-057, dated November 
22, 2011.

(h) Repair

    If any chafing or damage is found during any inspection required 
by paragraph (g) of this AD: Before further flight, repair in 
accordance with a method approved by the Manager, International 
Branch, ANM-116, Transport Airplane Directorate, FAA; or the 
European Aviation Safety Agency (EASA) (or its delegated agent).

(i) Reporting

    Submit a report of the findings (both positive and negative) of 
the inspection required by paragraph (g) of this AD to Saab AB, Saab 
Aerosystems, in accordance with the Accomplishment Instructions of 
Saab Service Bulletin 2000-53-057, dated November 22, 2011, at the 
applicable time specified in paragraph (h)(1) or (h)(2) of this AD. 
The report must include the inspection results, the airplane serial 
number, and the number of landings and flight hours on the airplane.
    (1) If the inspection was done on or after the effective date of 
this AD: Submit the report within 30 days after the inspection.
    (2) If the inspection was done before the effective date of this 
AD: Submit the report within 30 days after the effective date of 
this AD.

(j) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Branch, ANM-116, Transport Airplane Directorate, FAA, 
has the authority to approve AMOCs for this AD, if requested using 
the procedures found in 14 CFR 39.19. In accordance with 14 CFR 
39.19, send your request to your principal inspector or local Flight 
Standards District Office, as appropriate. If sending information 
directly to the International Branch, send it to ATTN: Shahram 
Daneshmandi, Aerospace Engineer, International Branch, ANM-116, 
Transport Airplane Directorate, FAA, 1601 Lind Avenue SW., Renton, 
WA 98057-3356; telephone 425-227-1112; fax 425-227-1149. Information 
may be emailed to: 9-ANM-116-AMOC-REQUESTS@faa.gov. Before using any 
approved AMOC, notify your appropriate principal inspector, or 
lacking a principal inspector, the manager of the local flight 
standards district office/certificate holding district office. The 
AMOC approval letter must specifically reference this AD.
    (2) Airworthy Product: For any requirement in this AD to obtain 
corrective actions from a manufacturer or other source, use these 
actions if they are FAA-approved. Corrective actions are considered 
FAA-approved if they are approved by the State of Design Authority 
(or their delegated agent). You are required to assure the product 
is airworthy before it is returned to service.
    (3) Reporting Requirements: A federal agency may not conduct or 
sponsor, and a person is not required to respond to, nor shall a 
person be subject to a penalty for failure to comply with a 
collection of information subject to the requirements of the 
Paperwork Reduction Act unless that collection of information 
displays a current valid OMB Control Number. The OMB Control Number 
for this information collection is 2120-0056. Public reporting for 
this collection of information is estimated to be approximately 5 
minutes per response, including the time for reviewing instructions, 
completing and reviewing the collection of information. All 
responses to this collection of information are mandatory. Comments 
concerning the accuracy of this burden and suggestions for reducing 
the burden should be directed to the FAA at: 800 Independence Ave. 
SW., Washington, DC 20591, Attn: Information Collection Clearance 
Officer, AES-200.

(k) Related Information

    (1) Refer to MCAI EASA Airworthiness Directive 2012-0068, dated 
April 25, 2012;

[[Page 60075]]

and Saab Service Bulletin 2000-53-057, dated November 22, 2011; for 
related information.
    (2) For service information identified in this AD, contact Saab 
AB, Saab Aeronautics, SE-581 88, Link[ouml]ping, Sweden; telephone 
+46 13 18 5591; fax +46 13 18 4874; email 
saab2000.techsupport@saabgroup.com; Internet http://www.saabgroup.com. You may review copies of the referenced service 
information at the FAA, Transport Airplane Directorate, 1601 Lind 
Avenue SW., Renton, WA. For information on the availability of this 
material at the FAA, call 425-227-1221.

    Issued in Renton, Washington, on September 21, 2012.
Ali Bahrami,
Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2012-24173 Filed 10-1-12; 8:45 am]
BILLING CODE 4910-13-P


