
[Federal Register Volume 77, Number 185 (Monday, September 24, 2012)]
[Proposed Rules]
[Pages 58785-58787]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: 2012-23431]


=======================================================================
-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2012-1000; Directorate Identifier 2012-NM-065-AD]
RIN 2120-AA64


Airworthiness Directives; Airbus Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to adopt a new airworthiness directive (AD) for all 
Airbus Model A300 B4-601, B4-603, B4-620, B4-605R, and B4-622R 
airplanes. This proposed AD was prompted by a report that the door 
frame shells of passenger doors 2 and 4 may not have sufficient 
structural strength to enable the airplane to operate safely. This 
proposed AD would require reinforcing of the door frame shells of 
passenger doors 2 and 4 on both sides of the fuselage. We are proposing 
this AD to prevent structural failure of the door frame shells, which 
could result in in-flight decompression of the airplane and consequent 
injury to passengers.

DATES: We must receive comments on this proposed AD by November 8, 
2012.

ADDRESSES: You may send comments by any of the following methods:
     Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: (202) 493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC 20590.
     Hand Delivery: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC, between 9 a.m. and 5 p.m., Monday 
through Friday, except Federal holidays.
    For service information identified in this proposed AD, contact 
Airbus SAS--EAW (Airworthiness Office), 1 Rond Point Maurice Bellonte, 
31707 Blagnac Cedex, France; telephone +33 5 61 93 36 96; fax +33 5 61 
93 44 51; email account.airworth-eas@airbus.com; Internet http://www.airbus.com. You may review copies of the referenced service 
information at the FAA, Transport Airplane Directorate, 1601 Lind 
Avenue SW., Renton, WA. For information on the availability of this 
material at the FAA, call 425-227-1221.

Examining the AD Docket

    You may examine the AD docket on the Internet at http://www.regulations.gov; or in person at the Docket Operations office 
between 9 a.m. and 5 p.m., Monday through Friday, except Federal 
holidays. The AD docket contains this proposed AD, the regulatory 
evaluation, any comments received, and other information. The street 
address for the Docket Operations office (telephone (800) 647-5527) is 
in the ADDRESSES section. Comments will be available in the AD docket 
shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Dan Rodina, Aerospace Engineer, 
International Branch, ANM-116, Transport Airplane Directorate, FAA, 
1601 Lind Avenue SW., Renton, WA 98057-3356; telephone 425-227-2125; 
fax 425-227-1149.

SUPPLEMENTARY INFORMATION: 

Comments Invited

    We invite you to send any written relevant data, views, or 
arguments about this proposed AD. Send your comments to an address 
listed under the ADDRESSES section. Include ``Docket No. FAA-2012-1000; 
Directorate Identifier 2012-NM-065-AD'' at the beginning of your 
comments. We specifically invite comments on the overall regulatory, 
economic, environmental, and energy aspects of this proposed AD. We 
will consider all comments received by the closing date and may amend 
this proposed AD based on those comments.
    We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this proposed AD.

Discussion

    The European Aviation Safety Agency (EASA), which is the Technical 
Agent for the Member States of the European Community, has issued EASA 
Airworthiness Directive 2012-0044, dated March 23, 2012 (referred to 
after this as ``the MCAI''), to correct an unsafe condition for the 
specified products. The MCAI states:

    As a result of the Extended Service Goal 2 exercise (ESG2) it 
was shown that the door frame shells of passenger doors 2 and 4 
(both sides of the aeroplane) may not have sufficient structural 
strength to enable the aeroplane to operate safety beyond ESG1 
(Extended Service Goal 1 equal to 42,500 Flight Cycles--FC or 89,000 
Flight Hours--FH) and up to ESG2 (Extended Service Goal 2 equal to 
51,000 FC or 89,000 FH) limits.
    This condition, if not corrected, could lead to structural 
failure of the affected door shells, possibly resulting in in-flight 
decompression of the aeroplane and consequent injury to occupants.
    For the reasons stated above, this [EASA] AD requires the 
reinforcement at door frame shells of passenger doors 2 and 4.

You may obtain further information by examining the MCAI in the AD 
docket.

Relevant Service Information

    Airbus has issued Service Bulletin A300-53-6170, dated May 16, 
2011. The actions described in this service information are intended to 
correct the unsafe condition identified in the MCAI.

FAA's Determination and Requirements of This Proposed AD

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to our bilateral agreement with the State of Design Authority, we have 
been notified

[[Page 58786]]

of the unsafe condition described in the MCAI and service information 
referenced above. We are proposing this AD because we evaluated all 
pertinent information and determined an unsafe condition exists and is 
likely to exist or develop on other products of the same type design.

Costs of Compliance

    Based on the service information, we estimate that this proposed AD 
would affect about 124 products of U.S. registry. We also estimate that 
it would take about 400 work-hours per product to comply with the basic 
requirements of this proposed AD. The average labor rate is $85 per 
work-hour. Required parts would cost about $10,000 per product. Where 
the service information lists required parts costs that are covered 
under warranty, we have assumed that there will be no charge for these 
parts. As we do not control warranty coverage for affected parties, 
some parties may incur costs higher than estimated here. Based on these 
figures, we estimate the cost of the proposed AD on U.S. operators to 
be $5,456,000, or $44,000 per product.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more detail the scope of the Agency's 
authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979);
    3. Will not affect intrastate aviation in Alaska; and
    4. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.
    We prepared a regulatory evaluation of the estimated costs to 
comply with this proposed AD and placed it in the AD docket.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

    1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

    2. The FAA amends Sec.  39.13 by adding the following new AD:

Airbus: Docket No. FAA-2012-1000; Directorate Identifier 2012-NM-
065-AD.

(a) Comments Due Date

    We must receive comments by November 8, 2012.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Airbus Model A300 B4-601, B4-603, B4-620, B4-
605R, and B4-622R airplanes; certificated in any category; all 
serial numbers.

(d) Subject

    Air Transport Association (ATA) of America Code 53, Fuselage.

(e) Reason

    This AD was prompted by a report that the door frame shells of 
passenger doors 2 and 4 may not have sufficient structural strength 
to enable the airplane to operate safely. We are issuing this AD to 
prevent structural failure of the door frame shells, which could 
result in in-flight decompression of the airplane and consequent 
injury to passengers.

(f) Compliance

    You are responsible for having the actions required by this AD 
performed within the compliance times specified, unless the actions 
have already been done.

(g) Reinforcement

    Before the accumulation of 42,500 total flight cycles or within 
2,000 flight cycles after the effective date of this AD, whichever 
occurs later: Do the actions specified in paragraph (g)(1) or (g)(2) 
of this AD, as applicable.
    (1) For Model A300 B4-622R airplanes: Reinforce the door frame 
shells of passenger doors 2 and 4 on both sides of the fuselage, in 
accordance with the Accomplishment Instructions of Airbus Service 
Bulletin A300-53-6170, dated May 16, 2011.
    (2) For Model A300 B4-601, B4-603, B4-620, and B4-605R 
airplanes: Reinforce the door frame shells of passenger doors 2 and 
4 on both sides of the fuselage, using a method approved by either 
the Manager, International Branch, ANM-116, Transport Airplane 
Directorate, FAA; or the European Aviation Safety Agency (EASA) (or 
its delegated agent).

(h) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Branch, ANM-116, FAA, has the authority to approve 
AMOCs for this AD, if requested using the procedures found in 14 CFR 
39.19. In accordance with 14 CFR 39.19, send your request to your 
principal inspector or local Flight Standards District Office, as 
appropriate. If sending information directly to the International 
Branch, send it to ATTN: Dan Rodina, Aerospace Engineer, 
International Branch, ANM-116, Transport Airplane Directorate, FAA, 
1601 Lind Avenue SW., Renton, WA 98057-3356; telephone 425-227-2125; 
fax 425-227-1149. Information may be emailed to: 9-ANM-116-AMOC-REQUESTS@faa.gov. Before using any approved AMOC, notify your 
appropriate principal inspector, or lacking a principal inspector, 
the manager of the local flight standards district office/
certificate holding district office. The AMOC approval letter must 
specifically reference this AD.
    (2) Airworthy Product: For any requirement in this AD to obtain 
corrective actions from a manufacturer or other source, use these 
actions if they are FAA-approved. Corrective actions are considered 
FAA-approved if they are approved by the State of Design Authority 
(or their delegated agent). You are required to assure the product 
is airworthy before it is returned to service.

(i) Related Information

    (1) Refer to MCAI EASA Airworthiness Directive 2012-0044, dated 
March 23, 2012; and Airbus Service Bulletin A300-53-6170, dated May 
16, 2011; for related information.
    (2) For service information identified in this AD, contact 
Airbus SAS-EAW (Airworthiness Office), 1 Rond Point Maurice 
Bellonte, 31707 Blagnac Cedex, France; telephone +33 5 61 93 36 96; 
fax +33 5 61 93 44 51; email account.airworth-eas@airbus.com; 
Internet http://www.airbus.com. You may review copies of the 
referenced service information at the FAA, Transport Airplane 
Directorate, 1601 Lind Avenue SW., Renton, WA. For information on 
the availability of this material at the FAA, call 425-227-1221.


[[Page 58787]]


    Issued in Renton, Washington, on September 12, 2012.
Ali Bahrami,
Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2012-23431 Filed 9-21-12; 8:45 am]
BILLING CODE 4910-13-P


