
[Federal Register Volume 76, Number 138 (Tuesday, July 19, 2011)]
[Proposed Rules]
[Pages 42602-42607]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: 2011-18131]


=======================================================================
-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2011-0717; Directorate Identifier 2010-NM-108-AD]
RIN 2120-AA64


Airworthiness Directives; Airbus Model A330-201, -202, -203, -
223, -243, -301, -302, -303, -321, -322, -323, -341, -342, and -343 
Airplanes; and Model A340-200 and -300 Series Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to adopt a new airworthiness directive (AD) for the 
products listed above that would supersede an existing AD. This 
proposed AD results from mandatory continuing airworthiness information 
(MCAI) originated by an aviation authority of another country to 
identify and correct an unsafe condition on an aviation product. The 
MCAI describes the unsafe condition as:

    During A330 and A340 aeroplanes fatigue tests, cracks appeared 
on the right (RH) and left (LH) sides between the crossing area of 
the keel beam fitting and the front spar of the Centre Wing Box 
(CWB). This condition, if not corrected, could lead to keel beam 
rupture which would affect the area structural integrity.
* * * * *

The proposed AD would require actions that are intended to address the 
unsafe condition described in the MCAI.

DATES: We must receive comments on this proposed AD by September 2, 
2011.

ADDRESSES: You may send comments by any of the following methods:
     Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: (202) 493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue, SE., Washington, DC 20590.
     Hand Delivery: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-40, 1200 New 
Jersey Avenue, SE., Washington, DC, between 9 a.m. and 5 p.m., Monday 
through Friday, except Federal holidays.
    For service information identified in this proposed AD, contact 
Airbus SAS--Airworthiness Office--EAL, 1 Rond Point Maurice Bellonte, 
31707 Blagnac Cedex, France; telephone +33 5 61 93 36 96; fax +33 5 61 
93 45 80; e-mail airworthiness.A330-A340@airbus.com; Internet http://www.airbus.com. You may review copies of the referenced service 
information at the FAA, Transport Airplane Directorate, 1601 Lind 
Avenue, SW., Renton, Washington. For information on the availability of 
this material at the FAA, call 425-227-1221.

Examining the AD Docket

    You may examine the AD docket on the Internet at http://www.regulations.gov; or in person at the Docket Operations office 
between 9 a.m. and 5 p.m., Monday through Friday, except Federal 
holidays. The AD docket contains this proposed AD, the regulatory 
evaluation, any comments received, and other information. The street 
address for the Docket Operations office (telephone (800) 647-5527) is 
in the ADDRESSES section. Comments will be available in the AD docket 
shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Vladimir Ulyanov, Aerospace Engineer, 
International Branch, ANM-116, Transport Airplane Directorate, FAA, 
1601 Lind Avenue, SW., Renton, Washington 98057-3356; telephone (425) 
227-1138; fax (425) 227-1149.

SUPPLEMENTARY INFORMATION: 

Comments Invited

    We invite you to send any written relevant data, views, or 
arguments about this proposed AD. Send your comments to an address 
listed under the ADDRESSES section. Include ``Docket No. FAA-2011-0717; 
Directorate Identifier 2010-NM-108-AD'' at the beginning of your 
comments. We specifically invite comments on the overall regulatory, 
economic, environmental, and energy aspects of this proposed AD. We 
will consider all comments received by the closing date and may amend 
this proposed AD based on those comments.
    We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this proposed AD.

Discussion

    On July 24, 2007, we issued AD 2007-16-02, Amendment 39-15141 (72 
FR 44731, August 9, 2007). That AD required actions intended to address 
an unsafe condition on the products listed above.
    Since we issued AD 2007-16-02, the European Aviation Safety Agency 
(EASA), which is the Technical Agent for the Member States of the 
European Community, has issued EASA Airworthiness Directive 2010-0024, 
dated February 12, 2010 (referred to after this as ``the MCAI''), to 
correct an unsafe condition for the specified products. The MCAI 
states:

    During A330 and A340 aeroplanes fatigue tests, cracks appeared 
on the right (RH) and left (LH) sides between the crossing area of 
the keel beam fitting and the front spar of the Centre Wing Box 
(CWB). This condition, if not corrected, could lead to keel beam 
rupture which would affect the area structural integrity.
    In order to maintain the structural integrity of the aeroplane, 
EASA AD 2006-0315R1 required repetitive special detailed

[[Page 42603]]

inspections on the horizontal flange of the keel beam in the area of 
first fastener hole aft of FR40.
    This AD, which supersedes EASA AD 2006-0315R1:

--Retains the inspection requirements of EASA AD 2006-0315R1,
--Extends the AD applicability to aeroplanes which have embodied 
Airbus modification 49202, and
--Modifies the inspection thresholds and intervals.

You may obtain further information by examining the MCAI in the AD 
docket.

Relevant Service Information

    Airbus has issued the following service information.

                                           Table--Service Information
----------------------------------------------------------------------------------------------------------------
                 Document                            Revision                              Date
----------------------------------------------------------------------------------------------------------------
Airbus Mandatory Service Bulletin A330-57- 03..........................  July 31, 2009.
 3081, including Appendix 1.
Airbus Mandatory Service Bulletin A340-57- 03..........................  July 31, 2009.
 4089, including Appendix 1.
Airbus Service Bulletin A330-57-3090.....  Original....................  March 27, 2006.
Airbus Service Bulletin A330-57-3098,      01..........................  July 31, 2009.
 including Appendix 1.
Airbus Service Bulletin A340-57-4106,      01..........................  July 31, 2009.
 including Appendix 1.
Airbus Service Bulletin A340-57-4098.....  Original....................  March 27, 2006.
----------------------------------------------------------------------------------------------------------------

    Airbus Mandatory Service Bulletins A330-57-3081, Revision 03, dated 
July 31, 2009; and A340-57-4089, Revision 03, dated July 31, 2009; 
reduce certain compliance times. The compliance time for the initial 
special detailed inspection ranges from 10,350 flight cycles or 69,870 
flight hours, to 21,180 flight cycles or 63,560 flight hours, depending 
on airplane configuration. The compliance times for the repetitive 
interval range from 7,780 flight cycles or 52,510 flight hours, to 
12,360 flight cycles or 37,080 flight hours, depending on airplane 
configuration. The actions described in this service information are 
intended to correct the unsafe condition identified in the MCAI.

FAA's Determination and Requirements of This Proposed AD

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to our bilateral agreement with the State of Design Authority, we have 
been notified of the unsafe condition described in the MCAI and service 
information referenced above. We are proposing this AD because we 
evaluated all pertinent information and determined an unsafe condition 
exists and is likely to exist or develop on other products of the same 
type design.

Change to Existing AD

    This proposed AD would retain all requirements of AD 2007-16-02. 
Since AD 2007-16-02 was issued, the AD format has been revised, and 
certain paragraphs have been rearranged. As a result, the corresponding 
paragraph identifiers have changed in this proposed AD, as listed in 
the following table:

                      Revised Paragraph Identifiers
------------------------------------------------------------------------
                                      Corresponding  requirement in this
    Requirement in AD 2007-16-02                 proposed AD
------------------------------------------------------------------------
          paragraph (e)(1)                        paragraph (h)
          paragraph (e)(2)                        paragraph (i)
          paragraph (e)(3)                        paragraph (j)
          paragraph (e)(4)                        paragraph (k)
          paragraph (e)(5)                        paragraph (l)
          paragraph (e)(6)                        paragraph (m)
------------------------------------------------------------------------

Differences Between This AD and the MCAI or Service Information

    We have reviewed the MCAI and related service information and, in 
general, agree with their substance. But we might have found it 
necessary to use different words from those in the MCAI to ensure the 
AD is clear for U.S. operators and is enforceable. In making these 
changes, we do not intend to differ substantively from the information 
provided in the MCAI and related service information.
    We might also have proposed different actions in this AD from those 
in the MCAI in order to follow FAA policies. Any such differences are 
highlighted in a Note within the proposed AD.

Costs of Compliance

    Based on the service information, we estimate that this proposed AD 
would affect about 35 products of U.S. registry.
    For the 9 airplanes affected by the existing AD, the actions that 
are required by AD 2007-16-02 and retained in this proposed AD take 
about 41 work-hours per product, at an average labor rate of $85 per 
work hour. Required parts cost about $191 per product. Based on these 
figures, the estimated cost of the currently required actions is $3,676 
per product.
    For the 26 additional airplanes added in this AD, we estimate the 
actions in this proposed AD would take about 41 work-hours per product, 
at an average labor rate of $85 per work hour. Required parts would 
cost about $191 per product. Based on these figures, the estimated cost 
of the proposed AD is $3,676 per product.
    In addition, because the proposed AD advises to contact the 
manufacturer for repair instructions, we cannot estimate the parts or 
labor costs for any necessary follow-on actions. We have no way of 
determining the number of products that may need these actions.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more detail the scope of the Agency's 
authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.

[[Page 42604]]

    For the reasons discussed above, I certify this proposed 
regulation:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979); and
    3. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.
    We prepared a regulatory evaluation of the estimated costs to 
comply with this proposed AD and placed it in the AD docket.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

    1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

    2. The FAA amends Sec.  39.13 by removing Amendment 39-15141 (72 FR 
44731, August 9, 2007) and adding the following new AD:

Airbus: Docket No. FAA-2011-0717; Directorate Identifier 2010-NM-
108-AD.

Comments Due Date

    (a) We must receive comments by September 2, 2011.

Affected ADs

    (b) This AD supersedes AD 2007-16-02, Amendment 39-15141.

Applicability

    (c) This AD applies to the airplanes identified in paragraphs 
(c)(1) and (c)(2) of this AD; certificated in any category; except 
as provided by paragraph (c)(3) of this AD.
    (1) Airbus Model A330-201, -202, -203, -223, -243, -301, -302, -
303, -321, -322, -323, -341, -342, and -343 airplanes, all serial 
numbers, except those on which Airbus modification 55306 or 55792 
has been embodied in production.
    (2) Airbus Model A340-211, -212, -213, -311, -312, and -313 
airplanes, all serial numbers, except those on which Airbus 
modification 55306 or 55792 has been embodied in production.
    (3) This AD is not applicable to Airbus Model A340-211, -212, -
213, -311, -312, and -313 airplanes that have been repaired in 
accordance with Airbus Repair Drawing R57115053, R57115051, or 
R57115047 (installation of titanium doubler on both sides). AD 2007-
12-08, Amendment 39-15086 (72 FR 31171, June 6, 2007), applies to 
these airplanes.

Subject

    (d) Air Transport Association (ATA) of America Code 57: Wings.

Reason

    (e) The mandatory continuing airworthiness information (MCAI) 
states:
    During A330 and A340 aeroplanes fatigue tests, cracks appeared 
on the right (RH) and left (LH) sides between the crossing area of 
the keel beam fitting and the front spar of the Centre Wing Box 
(CWB). This condition, if not corrected, could lead to keel beam 
rupture which would affect the area structural integrity.
* * * * *

Compliance

    (f) You are responsible for having the actions required by this 
AD performed within the compliance times specified, unless the 
actions have already been done.

Restatement of Requirements of AD 2007-16-02, With Revised Service 
Information

    (g) For Model A330-201, -202, -203, -223, -243, -301, -321, -
322, -323, -341, -342, and -343 airplanes, except those on which 
Airbus modification 49202 has been embodied in production, or Airbus 
Service Bulletin A330-57-3090 has been embodied in service, and 
Model A340-200 and -300 series airplanes, except those on which 
Airbus modification 49202 has been embodied in production or Airbus 
Service Bulletin A340-57-4098 has been embodied in service, and 
except Model A340-211, -212, -213, -311, -312, and -313 airplanes 
that have been repaired in accordance with Airbus Repair Drawing 
R57115053, R57115051, or R57115047: Do the actions required by 
paragraphs (h), (l), and (m) of this AD.
    (h) For airplanes identified in paragraph (g) of this AD, within 
the mandatory threshold (flight cycles or flight hours) mentioned in 
the paragraph 1.E.(2) of Airbus Mandatory Service Bulletin A340-57-
4089, Revision 02; or A330-57-3081, Revision 02; both dated January 
24, 2006; depending on the configuration of the aircraft model; or 
within 3 months after September 13, 2007 (the effective date of AD 
2007-16-02); whichever occurs later: Carry out the NDT (non-
destructive test) inspection of the hole(s) of the horizontal flange 
of the keel beam located on FR 40 datum on RH (right-hand) and/or LH 
(left-hand) side of the fuselage, in accordance with the 
instructions of the applicable service bulletin listed in table 1 of 
this AD. After the effective date of this AD, use only Airbus 
Mandatory Service Bulletin A330-57-3081, Revision 03, dated July 31, 
2009; or Airbus Mandatory Service Bulletin A340-57-4089, Revision 
03, dated July 31, 2009; as applicable. Inspection in accordance 
with Airbus A330/A340 200-300 Technical Disposition F57D03012810, 
Issue B, dated August 18, 2003; or 582.0651/2002, Issue A, dated 
October 17, 2002; satisfies the inspection requirements for the 
first rotating probe inspection which is specified at the inspection 
threshold of this AD. Doing the inspection required by paragraph (n) 
of this AD terminates the requirements of this paragraph of this AD.

    Note 1:  In order to prevent large repairs or heavy maintenance, 
Airbus recommends to perform the above inspection according to 
recommended thresholds mentioned in paragraph 1.E.(2) of Airbus 
Mandatory Service Bulletin A340-57-4089, Revision 02; or Airbus 
Mandatory Service Bulletin A330-57-3081, Revision 02; both dated 
January 24, 2006.


   Table 1--Acceptable Service Information for Certain Requirements of
                              Paragraph (h)
------------------------------------------------------------------------
          Document               Revision                Date
------------------------------------------------------------------------
Airbus Mandatory Service                  02  January 24, 2006.
 Bulletin A330-57-3081.
Airbus Mandatory Service                  03  July 31, 2009.
 Bulletin A330-57-3081.
Airbus Mandatory Service                  02  January 24, 2006.
 Bulletin A340-57-4089.
Airbus Mandatory Service                  03  July 31, 2009.
 Bulletin A340-57-4089.
------------------------------------------------------------------------

     (i) In case of any crack finding during the inspection required 
by paragraph (h) of this AD, before further flight, contact Airbus 
in order to get repair instructions before next flight, and repair 
before further flight.
    (j) Should no crack be detected during the inspection required 
by paragraph (h) of this AD:
    (1) Before further flight: Follow up the actions indicated in 
the flow charts, Figure 7, 8, or 9, of Airbus Mandatory Service 
Bulletin A340-57-4089, including Appendix 01, Revision 02, dated 
January 24, 2006, or Revision 03, dated July 31, 2009; or Figure 5, 
6, or 7, of Airbus Mandatory Service Bulletin A330-57-3081, 
including Appendix 01, Revision 02, dated January 24, 2006, or 
Revision 03, dated July 31, 2009; in accordance with the 
instructions of Airbus Mandatory Service Bulletin A340-57-4089, 
including Appendix 01, Revision 02, dated January 24, 2006, or 
Revision 03, dated July 31, 2009; or Airbus Mandatory Service 
Bulletin A330-57-3081, including Appendix 01, Revision 02, dated 
January 24, 2006, or

[[Page 42605]]

Revision 03, dated July 31, 2009; as applicable.
    (2) Within 30 days after September 13, 2007, or within 30 days 
after doing the inspection required by paragraph (h) of this AD, 
whichever occurs later: Send the report of actions carried out in 
paragraph (j)(1) of this AD to Airbus.
    (3) Renew the inspection at mandatory intervals given in 
paragraph 1.E.(2) of Airbus Mandatory Service Bulletin A340-57-4089, 
Revision 02, dated January 24, 2006; or Airbus Mandatory Service 
Bulletin A330-57-3081, Revision 02, dated January 24, 2006; as 
applicable; in accordance with the instructions of Airbus Mandatory 
Service Bulletin A340-57-4089, Revision 02, dated January 24, 2006, 
or Revision 03, dated July 31, 2009, or Airbus Mandatory Service 
Bulletin A330-57-3081, Revision 02, dated January 24, 2006, or 
Revision 03, dated July 31, 2009; as applicable, and send the 
inspection results to Airbus. Doing the inspection required by 
paragraph (n) of this AD terminates the requirements of this 
paragraph of this AD.

    Note 2:  In order to prevent large repairs or heavy maintenance, 
Airbus recommends to perform the above repetitive inspection 
according to recommended intervals mentioned in paragraph 1.E.(2) of 
Airbus Mandatory Service Bulletin A340-57-4089, Revision 02, dated 
January 24, 2006; or Airbus Mandatory Service Bulletin A330-57-3081, 
Revision 02, dated January 24, 2006.

    (k) Upon detection of a crack during a repetitive inspection 
required by paragraph (j)(3) of this AD, before further flight, 
contact Airbus to get repair instructions, and repair before further 
flight.
    (l) For airplanes identified in paragraph (g) of this AD: No 
additional work is required for compliance with paragraph (h) of 
this AD for aircraft inspected in accordance with the instructions 
of Airbus Service Bulletin A330-57-3081, dated October 30, 2003, or 
Revision 01, dated May 18, 2004; or Airbus Service Bulletin A340-57-
4089, dated October 30, 2003, or Revision 01, dated March 2, 2004. 
Nevertheless, the operators must check that their inspection program 
is in accordance with paragraph 1.E.(2) of Airbus Mandatory Service 
Bulletin A340-57-4089, Revision 02, dated January 24, 2006; or 
Airbus Mandatory Service Bulletin A330-57-3081, Revision 02, dated 
January 24, 2006; as applicable; for the repetitive inspection.
    (m) For airplanes identified in paragraph (g) of this AD on 
which Airbus Modification 41652 is not embodied: When the aircraft 
has been modified in accordance with Airbus Service Bulletin A330-
57-3090, dated March 27, 2006; or Airbus Service Bulletin A340-57-
4098, dated March 27, 2006; as applicable; the repetitive 
inspections required by this AD are cancelled. In case of any crack 
finding during the modification: Where the applicable service 
bulletin specifies to contact Airbus, before further flight, contact 
Airbus to get repair instructions, and repair.

New Requirements of This AD

    (n) At the applicable time in paragraph (n)(1) or (n)(2) of this 
AD: Do an NDT inspection of the hole(s) of the horizontal flange of 
the keel beam located on FR 40 datum on RH and/or LH side of the 
fuselage, in accordance with the Accomplishment Instructions of 
Airbus Mandatory Service Bulletin A330-57-3081, Revision 03, dated 
July 31, 2009; or Airbus Mandatory Service Bulletin A340-57-4089, 
Revision 03, dated July 31, 2009; as applicable. Inspection in 
accordance with Airbus A330/A340 Technical Disposition F57D03012810, 
Issue B, dated August 18, 2003; or 582.0651/2002, Issue A, dated 
October 17, 2002; is acceptable for compliance with the inspection 
requirements for the first rotating probe inspection required by 
this paragraph. Doing the inspection required by this paragraph 
terminates the requirements of paragraphs (h) and (j)(3) of this AD.
    (1) For airplanes on which an inspection required by paragraph 
(h) of this AD has not been done as of the effective date of this 
AD: At the applicable time specified in paragraph (n)(1)(i) or 
(n)(1)(ii) of this AD.
    (i) For all airplanes except those identified in paragraph (g) 
of this AD: Within the ``Mandatory Threshold'' (flight cycles or 
flight hours) specified in table 1 of paragraph 1.E.(2) of the 
Accomplishment Instructions of Airbus Mandatory Service Bulletin 
A330-57-3081, Revision 03, dated July 31, 2009; or Airbus Mandatory 
Service Bulletin A340-57-4089, Revision 03, dated July 31, 2009; as 
applicable; or within 3 months after the effective date of this AD; 
whichever occurs later. The compliance times for configuration 02 
through 06 specified in the ``Mandatory Threshold'' column in table 
1 of paragraph 1.E., ``Compliance,'' are total flight cycles and 
total flight hours.
    (ii) For airplanes identified in paragraph (g) of this AD: At 
the earlier of the times specified in paragraphs (n)(1)(ii)(A) and 
(n)(1)(ii)(B) of this AD.
    (A) Within the ``Mandatory Threshold'' (flight cycles or flight 
hours) specified in table 1 of paragraph 1.E.(2) of Airbus Mandatory 
Service Bulletin A340-57-4089, Revision 02, dated January 24, 2006; 
or Airbus Mandatory Service Bulletin A330-57-3081, Revision 02, 
dated January 24, 2006; depending on the configuration of the 
aircraft model; or within 3 months after September 13, 2007; 
whichever occurs later. The compliance times for Model A330 post-
mod. No. 41652 and pre-mod. No. 44360, post-mod. No. 44360, and pre-
mod. No. 49202 (specified in Airbus Mandatory Service Bulletin A330-
57-3081, Revision 02, dated January 24, 2006); and Model A340 post-
mod. No. 41652, post-mod. No. 43500 and pre-mod. No. 44360, post-
mod. No. 44360 and pre-mod. No. 49202, and Weight Variant 027 
(specified in Airbus Mandatory Service Bulletin A340-57-4089, 
Revision 02, dated January 24, 2006); specified in the ``Mandatory 
Threshold'' column in table 1 of paragraph 1.E., ``Compliance,'' are 
total flight cycles and total flight hours.
    (B) Within the ``Mandatory Threshold'' (flight cycles or flight 
hours) specified in table 1 of paragraph 1.E.(2) of the 
Accomplishment Instructions of Airbus Mandatory Service Bulletin 
A330-57-3081, Revision 03, dated July 31, 2009; or Airbus Mandatory 
Service Bulletin A340-57-4089, Revision 03, dated July 31, 2009; as 
applicable; or within 3 months after the effective date of this AD; 
whichever occurs later. The compliance times for configuration 02 
through 06 specified in the ``Mandatory Threshold'' column in table 
1 of paragraph 1.E., ``Compliance,'' are total flight cycles and 
total flight hours.
    (2) For airplanes on which an inspection required by paragraph 
(h) of this AD has been done as of the effective date of this AD: At 
the earlier of the times specified in paragraphs (n)(2)(i) and 
(n)(2)(ii) of this AD.
    (i) Within the ``Mandatory Intervals'' given in table 1 of 
paragraph 1.E.(2) of Airbus Mandatory Service Bulletin A340-57-4089, 
Revision 02, dated January 24, 2006; or Airbus Mandatory Service 
Bulletin A330-57-3081, Revision 02, dated January 24, 2006; as 
applicable.
    (ii) Within the applicable ``Mandatory Interval'' specified in 
table 1 of Paragraph 1.E.(2). of Airbus Mandatory Service Bulletin 
A330-57-3081, Revision 03, dated July 31, 2009; or Airbus Mandatory 
Service Bulletin A340-57-4089, Revision 03, dated July 31, 2009; as 
applicable; or within 3 months after the effective date of this AD; 
whichever occurs later.

    Note 3:  To prevent large repairs or heavy maintenance, Airbus 
recommends to perform the above inspection according to recommended 
thresholds specified in paragraph 1.E.(2) of Airbus Mandatory 
Service Bulletin A330-57-3081, Revision 03, dated July 31, 2009; or 
Airbus Mandatory Service Bulletin A340-57-4089, Revision 03, dated 
July 31, 2009; as applicable.

    (o) If any cracking is found during any inspection required by 
paragraph (n) of this AD, before further flight, repair in 
accordance with a method approved by the International Branch, ANM-
116, Transport Airplane Directorate, FAA, or EASA (or its delegated 
agent).
    (p) If no cracking is found during any inspection required by 
paragraph (n) of this AD, do the actions required by paragraphs 
(p)(1) and (p)(2) of this AD.
    (1) Before further flight: Install new or oversized fastener, as 
applicable; seal the fastener; and do all other applicable actions; 
in accordance with the Accomplishment Instructions of Airbus 
Mandatory Service Bulletin A330-57-3081, Revision 03, dated July 31, 
2009; or Airbus Mandatory Service Bulletin A340-57-4089, Revision 
03, dated July 31, 2009; as applicable.
    (2) Repeat the inspection required by paragraph (n) of this AD 
thereafter at intervals not to exceed the mandatory intervals 
specified in Paragraph 1.E.(2). of Airbus Mandatory Service Bulletin 
A330-57-3081, Revision 03, dated July 31, 2009; or Airbus Mandatory 
Service Bulletin A340-57-4089, Revision 03, dated July 31, 2009; as 
applicable.

    Note 4:  To prevent large repairs or heavy maintenance, Airbus 
recommends to perform the above repetitive inspection according to 
recommended intervals mentioned in paragraph 1.E.(2) of Airbus 
Mandatory Service Bulletin A330-57-3081, Revision 03, dated July 31, 
2009; or Airbus Mandatory Service Bulletin A340-57-4089, Revision 
03, dated July 31, 2009; as applicable.


[[Page 42606]]



Credit for Actions Accomplished in Accordance With Previous Service 
Information

    (q) Inspections done before the effective date of this AD in 
accordance with the service information specified in table 2 of this 
AD are acceptable for compliance with the corresponding inspection 
required by paragraph (n) of this AD.

                             Table 2--Credit Service Information for Certain Actions
----------------------------------------------------------------------------------------------------------------
                 Document                            Revision                              Date
----------------------------------------------------------------------------------------------------------------
Airbus Mandatory Service Bulletin A330-57- 02..........................  January 24, 2006.
 3081.
Airbus Mandatory Service Bulletin A340-57- 02..........................  January 24, 2006.
 4089.
Airbus Service Bulletin A330-57-3081.....  Original....................  October 30, 2003.
Airbus Service Bulletin A330-57-3081.....  01..........................  May 18, 2004.
Airbus Service Bulletin A340-57-4089.....  Original....................  October 30, 2003.
Airbus Service Bulletin A340-57-4089.....  01..........................  March 2, 2004.
----------------------------------------------------------------------------------------------------------------

    (r) Modifying the fasteners installation in the junction keel 
beam fitting at FR 40, in accordance with Airbus Service Bulletin 
A330-57-3098, dated August 30, 2007; or Airbus Service Bulletin 
A340-57-4106, dated August 30, 2007; as applicable; before the 
effective date of this AD terminates the requirements of this AD; 
except for airplanes on which a crack was detected at hole 5 before 
oversizing of the keel beam (in accordance with step 3.B.(1)(b)3 of 
the Accomplishment Instructions of Airbus Service Bulletin A330-57-
3098 or Airbus Service Bulletin A340-57-4106), before further 
flight, repair in accordance with a method approved by the 
International Branch, ANM-116, Transport Airplane Directorate, FAA, 
or EASA (or its delegated agent).
    (s) Modifying the fasteners installation in the junction keel 
beam fitting at FR 40, in accordance with Airbus Service Bulletin 
A330-57-3098, Revision 01, dated July 31, 2009; or Airbus Service 
Bulletin A340-57-4106, Revision 01, dated July 31, 2009; as 
applicable; terminates the requirements of this AD.
    (t) Modifying the fasteners installation in the junction keel 
beam fitting at FR 40, in accordance with Airbus Service Bulletin 
A330-57-3090, dated March 27, 2006; or Airbus Service Bulletin A340-
57-4098, dated March 27, 2006; as applicable; terminates the 
requirements of this AD.
    (u) In case of any crack finding during any modification 
specified paragraphs (r), (s), and (t) of this AD: Where the 
applicable service bulletin specifies to contact Airbus, before 
further flight, repair in accordance with a method approved by the 
International Branch, FAA, or EASA (or its delegated agent).

FAA AD Differences

    Note 5:  This AD differs from the MCAI and/or service 
information as follows: No differences.

Other FAA AD Provisions

    (v) The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Branch, FAA, has the authority to approve AMOCs for 
this AD, if requested using the procedures found in 14 CFR 39.19. In 
accordance with 14 CFR 39.19, send your request to your principal 
inspector or local Flight Standards District Office, as appropriate. 
If sending information directly to the International Branch, send it 
to ATTN: Vladimir Ulyanov, Aerospace Engineer, International Branch, 
ANM-116, Transport Airplane Directorate, FAA, 1601 Lind Avenue, SW., 
Renton, Washington 98057-3356; telephone (425) 227-1138; fax (425) 
227-1149. Information may be e-mailed to: 9-ANM-116-AMOC-REQUESTS@faa.gov. Before using any approved AMOC, notify your 
appropriate principal inspector, or lacking a principal inspector, 
the manager of the local flight standards district office/
certificate holding district office. The AMOC approval letter must 
specifically reference this AD.
    (2) Airworthy Product: For any requirement in this AD to obtain 
corrective actions from a manufacturer or other source, use these 
actions if they are FAA-approved. Corrective actions are considered 
FAA-approved if they are approved by the State of Design Authority 
(or their delegated agent). You are required to assure the product 
is airworthy before it is returned to service.

Related Information

    (w) Refer to MCAI European Aviation Safety Agency Airworthiness 
Directive 2010-0024, dated February 12, 2010, and the applicable 
service information specified/identified in table 3 of this AD, for 
related information.

                                      Table 3--Related Service Information
----------------------------------------------------------------------------------------------------------------
                 Document                            Revision                              Date
----------------------------------------------------------------------------------------------------------------
Airbus Mandatory Service Bulletin A330-57- 02..........................  January 24, 2006.
 3081.
Airbus Mandatory Service Bulletin A330-57- 03..........................  July 31, 2009.
 3081.
Airbus Mandatory Service Bulletin A340-57- 02..........................  January 24, 2006.
 4089.
Airbus Mandatory Service Bulletin A340-57- 03..........................  July 31, 2009.
 4089.
Airbus Service Bulletin A330-57-3090.....  Original....................  March 27, 2006.
Airbus Service Bulletin A330-57-3098.....  01..........................  July 31, 2009.
Airbus Service Bulletin A340-57-4106.....  01..........................  July 31, 2009.
Airbus Service Bulletin A340-57-4098.....  Original....................  March 27, 2006.
Airbus A330/A340 200-300 Technical         Issue B.....................  August 18, 2003.
 Disposition F57D03012810.
Airbus A330/A340 Technical Disposition     Issue A.....................  October 17, 2002.
 582.0651/2002.
----------------------------------------------------------------------------------------------------------------



[[Page 42607]]

    Issued in Renton, Washington, on July 7, 2011.
Kalene C. Yanamura,
Acting Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2011-18131 Filed 7-18-11; 8:45 am]
BILLING CODE 4910-13-P


