
[Federal Register Volume 76, Number 92 (Thursday, May 12, 2011)]
[Proposed Rules]
[Pages 27615-27617]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: 2011-11604]


 ========================================================================
 Proposed Rules
                                                 Federal Register
 ________________________________________________________________________
 
 This section of the FEDERAL REGISTER contains notices to the public of 
 the proposed issuance of rules and regulations. The purpose of these 
 notices is to give interested persons an opportunity to participate in 
 the rule making prior to the adoption of the final rules.
 
 ========================================================================
 

  Federal Register / Vol. 76, No. 92 / Thursday, May 12, 2011 / 
Proposed Rules  

[[Page 27615]]


=======================================================================
-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2011-0470; Directorate Identifier 2010-NM-190-AD]
RIN 2120-AA64


Airworthiness Directives; Bombardier, Inc. Model DHC-8-400 Series 
Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to adopt a new airworthiness directive (AD) for the 
products listed above. This proposed AD results from mandatory 
continuing airworthiness information (MCAI) originated by an aviation 
authority of another country to identify and correct an unsafe 
condition on an aviation product. The MCAI describes the unsafe 
condition as:

    One in-service incident has been reported on [a] DHC-8 Series 
400 aeroplane in which the right hand main landing gear (MLG) failed 
to extend using the alternate gear extension system. * * * Failure 
of [the] MLG to extend and lock could adversely affect the safe 
landing of the aeroplane.
* * * * *
The proposed AD would require actions that are intended to address the 
unsafe condition described in the MCAI.

DATES: We must receive comments on this proposed AD by June 27, 2011.

ADDRESSES: You may send comments by any of the following methods:
     Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: (202) 493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue, SE., Washington, DC 20590.
     Hand Delivery: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-40, 1200 New 
Jersey Avenue, SE., Washington, DC, between 9 a.m. and 5 p.m., Monday 
through Friday, except Federal holidays.
    For service information identified in this proposed AD, contact 
Bombardier, Inc., Q-Series Technical Help Desk, 123 Garratt Boulevard, 
Toronto, Ontario M3K 1Y5, Canada; telephone 416-375-4000; fax 416-375-
4539; e-mail thd.qseries@aero.bombardier.com; Internet http://www.bombardier.com. You may review copies of the referenced service 
information at the FAA, Transport Airplane Directorate, 1601 Lind 
Avenue, SW., Renton, Washington. For information on the availability of 
this material at the FAA, call 425-227-1221.

Examining the AD Docket

    You may examine the AD docket on the Internet at http://www.regulations.gov; or in person at the Docket Operations office 
between 9 a.m. and 5 p.m., Monday through Friday, except Federal 
holidays. The AD docket contains this proposed AD, the regulatory 
evaluation, any comments received, and other information. The street 
address for the Docket Operations office (telephone (800) 647-5527) is 
in the ADDRESSES section. Comments will be available in the AD docket 
shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Fabio Buttitta, Aerospace Engineer, 
Airframe and Mechanical Systems Branch, ANE-171, FAA, New York Aircraft 
Certification Office (ACO), 1600 Stewart Avenue, Suite 410, Westbury, 
New York 11590; telephone (516) 228-7303; fax (516) 794-5531.

SUPPLEMENTARY INFORMATION:

Comments Invited

    We invite you to send any written relevant data, views, or 
arguments about this proposed AD. Send your comments to an address 
listed under the ADDRESSES section. Include ``Docket No. FAA-2011-0470; 
Directorate Identifier 2010-NM-190-AD'' at the beginning of your 
comments. We specifically invite comments on the overall regulatory, 
economic, environmental, and energy aspects of this proposed AD. We 
will consider all comments received by the closing date and may amend 
this proposed AD based on those comments.
    We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this proposed AD.

Discussion

    Transport Canada Civil Aviation (TCCA), which is the aviation 
authority for Canada, has issued Canadian Airworthiness Directive CF-
2010-23, dated July 21, 2010 (referred to after this as ``the MCAI''), 
to correct an unsafe condition for the specified products. The MCAI 
states:

    One in-service incident has been reported on [a] DHC-8 Series 
400 aeroplane in which the right hand main landing gear (MLG) failed 
to extend using the alternate gear extension system. Investigation 
determined that the tread on the outboard tire was catching on the 
bumper plate located on the outboard MLG door that prevented the MLG 
door to open following an extension attempt via the alternate 
extension system. Failure of [the] MLG to extend and lock could 
adversely affect the safe landing of the aeroplane.
    To prevent the potential jam condition between the bumper plate 
and the MLG tires, Bombardier Aerospace has developed a modification 
to trim the edge of the bumper plate to eliminate the possibility of 
interference [Bombardier Modsum 4-113645].

The Modsum includes performing a detailed visual inspection for damage 
or cracks of the bumper plate and base fitting and replacing any 
damaged or cracked part with a new part, if necessary. You may obtain 
further information by examining the MCAI in the AD docket.

Relevant Service Information

    Bombardier has issued Service Bulletin 84-32-74, Revision A, dated 
May 17, 2010. The actions described in this service information are 
intended to correct the unsafe condition identified in the MCAI.

FAA's Determination and Requirements of This Proposed AD

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to our bilateral agreement with the State of Design Authority, we have 
been notified of the unsafe condition described in the MCAI and service 
information referenced above. We are proposing this

[[Page 27616]]

AD because we evaluated all pertinent information and determined an 
unsafe condition exists and is likely to exist or develop on other 
products of the same type design.

Differences Between This AD and the MCAI or Service Information

    We have reviewed the MCAI and related service information and, in 
general, agree with their substance. But we might have found it 
necessary to use different words from those in the MCAI to ensure the 
AD is clear for U.S. operators and is enforceable. In making these 
changes, we do not intend to differ substantively from the information 
provided in the MCAI and related service information.
    We might also have proposed different actions in this AD from those 
in the MCAI in order to follow FAA policies. Any such differences are 
highlighted in a NOTE within the proposed AD.

Costs of Compliance

    Based on the service information, we estimate that this proposed AD 
would affect about 65 products of U.S. registry. We also estimate that 
it would take about 8 work-hours per product to comply with the basic 
requirements of this proposed AD. The average labor rate is $85 per 
work-hour. Required parts would cost about $479 per product. Where the 
service information lists required parts costs that are covered under 
warranty, we have assumed that there will be no charge for these costs. 
As we do not control warranty coverage for affected parties, some 
parties may incur costs higher than estimated here. Based on these 
figures, we estimate the cost of the proposed AD on U.S. operators to 
be $75,335, or $1,159 per product.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more detail the scope of the Agency's 
authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979); and
    3. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.
    We prepared a regulatory evaluation of the estimated costs to 
comply with this proposed AD and placed it in the AD docket.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

    1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

    2. The FAA amends Sec.  39.13 by adding the following new AD:

Bombardier, Inc.: Docket No. FAA-2011-0470; Directorate Identifier 
2010-NM-190-AD.

Comments Due Date

    (a) We must receive comments by June 27, 2011.

Affected ADs

    (b) None.

Applicability

    (c) This AD applies to Bombardier, Inc. Model DHC-8-400, -401, 
and -402 airplanes, certificated in any category, having serial 
numbers 4001 through 4247 inclusive.

Subject

    (d) Air Transport Association (ATA) of America Code 32: Landing 
Gear.

Reason

    (e) The mandatory continuing airworthiness information (MCAI) 
states:
    One in-service incident has been reported on [a] DHC-8 Series 
400 aeroplane in which the right hand main landing gear (MLG) failed 
to extend using the alternate gear extension system. * * * Failure 
of [the] MLG to extend and lock could adversely affect the safe 
landing of the aeroplane.
* * * * *

Compliance

    (f) You are responsible for having the actions required by this 
AD performed within the compliance times specified, unless the 
actions have already been done.

Actions

    (g) Within 2,000 flight hours after the effective date of this 
AD: Incorporate Bombardier Modsum 4-113645, including performing a 
detailed visual inspection for damage or cracks of the bumper plate 
and base fitting and replacing any damaged or cracked part, in 
accordance with the Accomplishment Instructions of Bombardier 
Service Bulletin 84-32-74, Revision A, dated May 17, 2010. Do all 
applicable replacements before further flight.
    (h) For airplanes on which a bumper plate having part number 
85424082-101 or 85424082-103 is installed that has been reworked in 
accordance with Bombardier Repair Drawing 8/4-54-553: Within 1,000 
flight hours after the effective date of this AD, reidentify the 
bumper plate, in accordance with paragraph 3.B., step (8) of the 
Accomplishment Instructions of Bombardier Service Bulletin 84-32-74, 
Revision A, dated May 17, 2010.

    Note 1: Bombardier Service Bulletin 84-32-74, Revision A, dated 
May 17, 2010, includes an operational check of the alternate 
extension system of the MLG. If the check fails, guidance on doing 
corrective actions can be found in the Bombardier Q400 Dash 8 
Aircraft Maintenance Manual.

Credit for Actions Accomplished in Accordance With Previous Service 
Information

    (i) Incorporation of Bombardier Modsum 4-113645 before the 
effective date of this AD in accordance with Bombardier Service 
Bulletin 84-32-74, dated December 23, 2009, is considered acceptable 
for compliance with the modification in paragraph (h) of this AD, 
provided the action in paragraph (h) of this AD is done within the 
compliance time specified in paragraph (h) of this AD.

FAA AD Differences

    Note 2: This AD differs from the MCAI and/or service information 
as follows: No differences.

Other FAA AD Provisions

    (j) The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, New 
York Aircraft

[[Page 27617]]

Certification Office (ACO), ANE-170, FAA, has the authority to 
approve AMOCs for this AD, if requested using the procedures found 
in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request 
to your principal inspector or local Flight Standards District 
Office, as appropriate. If sending information directly to the New 
York ACO, send it to ATTN: Program Manager, Continuing Operational 
Safety, FAA, New York ACO, 1600 Stewart Avenue, Suite 410, Westbury, 
New York, 11590; telephone 516-228-7300; fax 516-794-5531. Before 
using any approved AMOC on any airplane to which the AMOC applies, 
notify your principal maintenance inspector (PMI) or principal 
avionics inspector (PAI), as appropriate, or lacking a principal 
inspector, your local Flight Standards District Office. The AMOC 
approval letter must specifically reference this AD.
    (2) Airworthy Product: For any requirement in this AD to obtain 
corrective actions from a manufacturer or other source, use these 
actions if they are FAA-approved. Corrective actions are considered 
FAA-approved if they are approved by the State of Design Authority 
(or their delegated agent). You are required to assure the product 
is airworthy before it is returned to service.

Related Information

    (k) Refer to MCAI Canadian Airworthiness Directive CF-2010-23, 
dated July 21, 2010; Bombardier Service Bulletin 84-32-74, Revision 
A, dated May 17, 2010; for related information.

    Issued in Renton, Washington, on May 5, 2011.
Kalene C. Yanamura,
Acting Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2011-11604 Filed 5-11-11; 8:45 am]
BILLING CODE 4910-13-P


