
[Federal Register Volume 75, Number 248 (Tuesday, December 28, 2010)]
[Rules and Regulations]
[Pages 81420-81421]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: 2010-32325]



[[Page 81420]]

-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2010-0805; Directorate Identifier 2010-NM-042-AD; 
Amendment 39-16553; AD 2010-26-13]
RIN 2120-AA64


Airworthiness Directives; Bombardier, Inc. Model DHC-8-300 Series 
Airplanes

AGENCY: Federal Aviation Administration (FAA), Department of 
Transportation (DOT).

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: We are adopting a new airworthiness directive (AD) for the 
products listed above. This AD results from mandatory continuing 
airworthiness information (MCAI) originated by an aviation authority of 
another country to identify and correct an unsafe condition on an 
aviation product. The MCAI describes the unsafe condition as:

    Several cases of aileron terminal quadrant support brackets that 
were manufactured using sheet metal have been found cracked on DHC-8 
Series 300 aircraft. Investigation revealed that the failure of the 
support bracket was due to fatigue. Failure of the aileron terminal 
quadrant support bracket could result in an adverse reduction of 
aircraft roll control.
* * * * *
These conditions could result in loss of control of the airplane. We 
are issuing this AD to require actions to correct the unsafe condition 
on these products.

DATES: This AD becomes effective February 1, 2011.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in this AD as of February 1, 
2011.

ADDRESSES: You may examine the AD docket on the Internet at http://www.regulations.gov or in person at the U.S. Department of 
Transportation, Docket Operations, M-30, West Building Ground Floor, 
Room W12-140, 1200 New Jersey Avenue, SE., Washington, DC.

FOR FURTHER INFORMATION CONTACT: Craig Yates, Aerospace Engineer, 
Airframe and Mechanical Systems Branch, ANE-171, FAA, New York Aircraft 
Certification Office (ACO), 1600 Stewart Avenue, Suite 410, Westbury, 
New York 11590; telephone (516) 228-7355; fax (516) 794-5531.

SUPPLEMENTARY INFORMATION:

Discussion

    We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR 
part 39 to include an AD that would apply to the specified products. 
That NPRM was published in the Federal Register on August 25, 2010 (75 
FR 52290). That NPRM proposed to correct an unsafe condition for the 
specified products. The MCAI states:

    Several cases of aileron terminal quadrant support brackets that 
were manufactured using sheet metal have been found cracked on DHC-8 
Series 300 aircraft. Investigation revealed that the failure of the 
support bracket was due to fatigue. Failure of the aileron terminal 
quadrant support bracket could result in an adverse reduction of 
aircraft roll control.
    This directive mandates the replacement of the aileron terminal 
quadrant support bracket with a new and improved machined part.

These conditions could result in loss of control of the airplane. The 
required actions include installing new aileron input quadrant support 
brackets. You may obtain further information by examining the MCAI in 
the AD docket.

Comments

    We gave the public the opportunity to participate in developing 
this AD. We considered the comment received. Air Line Pilots 
Association, International (ALPA), supports the NPRM.

Conclusion

    We reviewed the available data, including the comment received, and 
determined that air safety and the public interest require adopting the 
AD as proposed.

Differences Between This AD and the MCAI or Service Information

    We have reviewed the MCAI and related service information and, in 
general, agree with their substance. But we might have found it 
necessary to use different words from those in the MCAI to ensure the 
AD is clear for U.S. operators and is enforceable. In making these 
changes, we do not intend to differ substantively from the information 
provided in the MCAI and related service information.
    We might also have required different actions in this AD from those 
in the MCAI in order to follow our FAA policies. Any such differences 
are highlighted in a Note within the AD.

Costs of Compliance

    We estimate that this AD will affect 13 products of U.S. registry. 
We also estimate that it will take about 72 work-hours per product to 
comply with the basic requirements of this AD. The average labor rate 
is $85 per work-hour. Required parts will cost about $1,080 per 
product. Where the service information lists required parts costs that 
are covered under warranty, we have assumed that there will be no 
charge for these parts. As we do not control warranty coverage for 
affected parties, some parties may incur costs higher than estimated 
here. Based on these figures, we estimate the cost of this AD to the 
U.S. operators to be $93,600, or $7,200 per product.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more detail the scope of the Agency's 
authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this AD will not have federalism implications 
under Executive Order 13132. This AD will not have a substantial direct 
effect on the States, on the relationship between the national 
government and the States, or on the distribution of power and 
responsibilities among the various levels of government.
    For the reasons discussed above, I certify this AD:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979); and
    3. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.
    We prepared a regulatory evaluation of the estimated costs to 
comply with this AD and placed it in the AD docket.

Examining the AD Docket

    You may examine the AD docket on the Internet at http://www.regulations.gov; or in person at the Docket Operations office 
between 9 a.m.

[[Page 81421]]

and 5 p.m., Monday through Friday, except Federal holidays. The AD 
docket contains the NPRM, the regulatory evaluation, any comments 
received, and other information. The street address for the Docket 
Operations office (telephone (800) 647-5527) is in the ADDRESSES 
section. Comments will be available in the AD docket shortly after 
receipt.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

0
Accordingly, under the authority delegated to me by the Administrator, 
the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new AD:

2010-26-13 Bombardier, Inc.: Amendment 39-16553. Docket No. FAA-
2010-0805; Directorate Identifier 2010-NM-042-AD.

Effective Date

    (a) This airworthiness directive (AD) becomes effective February 
1, 2011.

Affected ADs

    (b) None.

Applicability

    (c) This AD applies to Bombardier, Inc. Model DHC-8-301, -311, 
and -315 airplanes, certificated in any category; having serial 
numbers 100 through 530 inclusive.

Subject

    (d) Air Transport Association (ATA) of America Code 57: Wings.

Reason

    (e) The mandatory continuing airworthiness information (MCAI) 
states:

    Several cases of aileron terminal quadrant support brackets that 
were manufactured using sheet metal have been found cracked on DHC-8 
Series 300 aircraft. Investigation revealed that the failure of the 
support bracket was due to fatigue. Failure of the aileron terminal 
quadrant support bracket could result in an adverse reduction of 
aircraft roll control.
* * * * *
These conditions could result in loss of control of the airplane.

Compliance

    (f) You are responsible for having the actions required by this 
AD performed within the compliance times specified, unless the 
actions have already been done.

Actions

    (g) For airplanes with an aileron terminal quadrant support 
bracket having part number (P/N) 85711569: At the applicable times 
specified in paragraph (g)(1) or (g)(2) of this AD, install a new 
aileron input quadrant support bracket by incorporating MODSUM 
8Q101250, in accordance with the Accomplishment Instructions of 
Bombardier Service Bulletin 8-57-43, Revision B, dated October 7, 
2009.
    (1) For airplanes that have accumulated 30,000 total flight 
hours or more as of the effective date of this AD: Within 3,000 
flight hours after the effective date of this AD.
    (2) For airplanes that have accumulated less than 30,000 total 
flight hours as of the effective date of this AD: Before the 
accumulation of 33,000 total flight cycles or within 6,000 flight 
hours after the effective date of this AD, whichever occurs first.

Credit for Actions Accomplished in Accordance With Previous Service 
Information

    (h) Doing the installation by incorporating MODSUM 8Q101250 is 
also acceptable for compliance with the requirements of paragraph 
(g) of this AD if done before the effective date of this AD in 
accordance with Bombardier Service Bulletin 8-57-43, dated August 9, 
2002; or Bombardier Service Bulletin 8-57-43, Revision A, dated 
January 17, 2003.

FAA AD Differences

    Note 1: This AD differs from the MCAI and/or service information 
as follows: No differences.

Other FAA AD Provisions

    (i) The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, New 
York Aircraft Certification Office (ACO), ANE-170, FAA, has the 
authority to approve AMOCs for this AD, if requested using the 
procedures found in 14 CFR 39.19. Send information to Attn: Program 
Manager, Continuing Operational Safety, FAA, New York ACO, 1600 
Stewart Avenue, Suite 410, Westbury, New York, 11590; telephone 516-
228-7300; fax 516-794-5531. Before using any approved AMOC on any 
airplane to which the AMOC applies, notify your principal 
maintenance inspector (PMI) or principal avionics inspector (PAI), 
as appropriate, or lacking a principal inspector, your local Flight 
Standards District Office. The AMOC approval letter must 
specifically reference this AD.
    (2) Airworthy Product: For any requirement in this AD to obtain 
corrective actions from a manufacturer or other source, use these 
actions if they are FAA-approved. Corrective actions are considered 
FAA-approved if they are approved by the State of Design Authority 
(or their delegated agent). You are required to assure the product 
is airworthy before it is returned to service.
    (3) Reporting Requirements: A federal agency may not conduct or 
sponsor, and a person is not required to respond to, nor shall a 
person be subject to a penalty for failure to comply with a 
collection of information subject to the requirements of the 
Paperwork Reduction Act unless that collection of information 
displays a current valid OMB Control Number. The OMB Control Number 
for this information collection is 2120-0056. Public reporting for 
this collection of information is estimated to be approximately 5 
minutes per response, including the time for reviewing instructions, 
completing and reviewing the collection of information. All 
responses to this collection of information are mandatory. Comments 
concerning the accuracy of this burden and suggestions for reducing 
the burden should be directed to the FAA at: 800 Independence Ave., 
SW., Washington, DC 20591, Attn: Information Collection Clearance 
Officer, AES-200.

Related Information

    (j) Refer to MCAI Canadian Airworthiness Directive CF-2009-45, 
dated December 11, 2009; and Bombardier Service Bulletin 8-57-43, 
Revision B, dated October 7, 2009; for related information.

Material Incorporated by Reference

    (k) You must use Bombardier Service Bulletin 8-57-43, Revision 
B, dated October 7, 2009, to do the actions required by this AD, 
unless the AD specifies otherwise.
    (1) The Director of the Federal Register approved the 
incorporation by reference of this service information under 5 
U.S.C. 552(a) and 1 CFR part 51.
    (2) For service information identified in this AD, contact 
Bombardier, Inc., Q-Series Technical Help Desk, 123 Garratt 
Boulevard, Toronto, Ontario M3K 1Y5, Canada; telephone 416-375-4000; 
fax 416-375-4539; e-mail thd.qseries@aero.bombardier.com; Internet 
http://www.bombardier.com.
    (3) You may review copies of the service information at the FAA, 
Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, 
Washington. For information on the availability of this material at 
the FAA, call 425-227-1221.
    (4) You may also review copies of the service information that 
is incorporated by reference at the National Archives and Records 
Administration (NARA). For information on the availability of this 
material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html.

    Issued in Renton, Washington, on December 16, 2010.
Ali Bahrami,
Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2010-32325 Filed 12-27-10; 8:45 am]
BILLING CODE 4910-13-P


