
[Federal Register: December 3, 2009 (Volume 74, Number 231)]
[Proposed Rules]               
[Page 63331-63333]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr03de09-9]                         

========================================================================
Proposed Rules
                                                Federal Register
________________________________________________________________________

This section of the FEDERAL REGISTER contains notices to the public of 
the proposed issuance of rules and regulations. The purpose of these 
notices is to give interested persons an opportunity to participate in 
the rule making prior to the adoption of the final rules.

========================================================================



[[Page 63331]]



DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2009-1111; Directorate Identifier 2009-NM-147-AD]
RIN 2120-AA64

 
Airworthiness Directives; Bombardier, Inc., Model CL-600-2C10 
(Regional Jet Series 700, 701 & 702), CL-600-2D15 (Regional Jet Series 
705), and CL-600-2D24 (Regional Jet Series 900) Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to adopt a new airworthiness directive (AD) for the 
products listed above. This proposed AD results from mandatory 
continuing airworthiness information (MCAI) originated by an aviation 
authority of another country to identify and correct an unsafe 
condition on an aviation product. The MCAI describes the unsafe 
condition as: During an elevator Power Control Unit (PCU) Centering 
Functional Check on two CL-600-2C10 aircraft, sustained oscillations 
were discovered when a control rod was disconnected. These sustained 
oscillations could render the elevator surface inoperable and cause 
subsequent loss of pitch control of the aircraft.
    Loss of pitch control could result in reduced controllability of 
the airplane. The proposed AD would require actions that are intended 
to address the unsafe condition described in the MCAI.

DATES: We must receive comments on this proposed AD by January 19, 
2010.

ADDRESSES: You may send comments by any of the following methods:
     Federal eRulemaking Portal: Go to http://
www.regulations.gov. Follow the instructions for submitting comments.
     Fax: (202) 493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue, SE., Washington, DC 20590.
     Hand Delivery: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-40, 1200 New 
Jersey Avenue, SE., Washington, DC, between 9 a.m. and 5 p.m., Monday 
through Friday, except Federal holidays.
    For service information identified in this proposed AD, contact 
Bombardier, Inc., 400 C[ocirc]te-Vertu Road West, Dorval, Qu[eacute]bec 
H4S 1Y9, Canada; telephone 514-855-5000; fax 514-855-7401; e-mail 
thd.crj@aero.bombardier.com; Internet http://www.bombardier.com. You 
may review copies of the referenced service information at the FAA, 
Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, 
Washington. For information on the availability of this material at the 
FAA, call 425-227-1221 or 425-227-1152.

Examining the AD Docket

    You may examine the AD docket on the Internet at http://
www.regulations.gov; or in person at the Docket Operations office 
between 9 a.m. and 5 p.m., Monday through Friday, except Federal 
holidays. The AD docket contains this proposed AD, the regulatory 
evaluation, any comments received, and other information. The street 
address for the Docket Operations office (telephone (800) 647-5527) is 
in the ADDRESSES section. Comments will be available in the AD docket 
shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Christopher Alfano, Aerospace 
Engineer, Airframe and Mechanical Systems Branch, ANE-171, FAA, New 
York Aircraft Certification Office, 1600 Stewart Avenue, Suite 410, 
Westbury, New York 11590; telephone (516) 228-7340; fax (516) 794-5531.

SUPPLEMENTARY INFORMATION:

Comments Invited

    We invite you to send any written relevant data, views, or 
arguments about this proposed AD. Send your comments to an address 
listed under the ADDRESSES section. Include ``Docket No. FAA-2009-1111; 
Directorate Identifier 2009-NM-147-AD'' at the beginning of your 
comments. We specifically invite comments on the overall regulatory, 
economic, environmental, and energy aspects of this proposed AD. We 
will consider all comments received by the closing date and may amend 
this proposed AD based on those comments.
    We have lengthened the 30-day comment period for proposed ADs that 
address MCAI originated by aviation authorities of other countries to 
provide adequate time for interested parties to submit comments. The 
comment period for these proposed ADs is now typically 45 days, which 
is consistent with the comment period for domestic transport ADs.
    We will post all comments we receive, without change, to http://
www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this proposed AD.

Discussion

    Transport Canada Civil Aviation, which is the aviation authority 
for Canada, has issued Canadian Airworthiness Directive CF-2009-28, 
issued June 29, 2009 (referred to after this as ``the MCAI''), to 
correct an unsafe condition for the specified products. The MCAI 
states:

    During an elevator Power Control Unit (PCU) Centering Functional 
Check on two CL-600-2C10 aircraft, sustained oscillations were 
discovered when a control rod was disconnected. These sustained 
oscillations could render the elevator surface inoperable and cause 
subsequent loss of pitch control of the aircraft.
    This directive mandates incorporation of a new centering 
mechanism on the elevator torque tube to prevent these sustained 
oscillations.

Loss of pitch control could result in reduced controllability of the 
airplane. You may obtain further information by examining the MCAI in 
the AD docket.

Relevant Service Information

    Bombardier has issued Service Bulletin 670BA-27-042, Revision B, 
dated June 2, 2009. The actions described in this service information 
are intended to correct the unsafe condition identified in the MCAI.

FAA's Determination and Requirements of This Proposed AD

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to our

[[Page 63332]]

bilateral agreement with the State of Design Authority, we have been 
notified of the unsafe condition described in the MCAI and service 
information referenced above. We are proposing this AD because we 
evaluated all pertinent information and determined an unsafe condition 
exists and is likely to exist or develop on other products of the same 
type design.

Differences Between This AD and the MCAI or Service Information

    We have reviewed the MCAI and related service information and, in 
general, agree with their substance. But we might have found it 
necessary to use different words from those in the MCAI to ensure the 
AD is clear for U.S. operators and is enforceable. In making these 
changes, we do not intend to differ substantively from the information 
provided in the MCAI and related service information.
    We might also have proposed different actions in this AD from those 
in the MCAI in order to follow FAA policies. Any such differences are 
highlighted in a NOTE within the proposed AD.

Costs of Compliance

    Based on the service information, we estimate that this proposed AD 
would affect about 260 products of U.S. registry. We also estimate that 
it would take about 35 work-hours per product to comply with the basic 
requirements of this proposed AD. The average labor rate is $80 per 
work-hour. Required parts would cost about $27,626 per product. Where 
the service information lists required parts costs that are covered 
under warranty, we have assumed that there will be no charge for these 
costs. As we do not control warranty coverage for affected parties, 
some parties may incur costs higher than estimated here. Based on these 
figures, we estimate the cost of the proposed AD on U.S. operators to 
be $7,910,760, or $30,426 per product.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more detail the scope of the Agency's 
authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979); and
    3. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.
    We prepared a regulatory evaluation of the estimated costs to 
comply with this proposed AD and placed it in the AD docket.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

    1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

    2. The FAA amends Sec.  39.13 by adding the following new AD:

Bombardier, Inc. (formerly Canadair): Docket No. FAA-2009-1111; 
Directorate Identifier 2009-NM-147-AD.

Comments Due Date

    (a) We must receive comments by January 19, 2010.

Affected ADs

    (b) None.

Applicability

    (c) This AD applies to the Bombardier, Inc., airplanes 
identified in paragraphs (c)(1) and (c)(2) of this AD, certificated 
in any category.
    (1) Model CL-600-2C10 (Regional Jet Series 700, 701 & 702) 
airplanes having serial numbers 10003 through 10259 inclusive.
    (2) Model CL-600-2D15 (Regional Jet Series 705) and Model CL-
600-2D24 (Regional Jet Series 900) airplanes having serial numbers 
15001 through 15099 inclusive.

Subject

    (d) Air Transport Association (ATA) of America Code 27: Flight 
controls.

Reason

    (e) The mandatory continuing airworthiness information (MCAI) 
states:

    During an elevator Power Control Unit (PCU) Centering Functional 
Check on two CL-600-2C10 aircraft, sustained oscillations were 
discovered when a control rod was disconnected. These sustained 
oscillations could render the elevator surface inoperable and cause 
subsequent loss of pitch control of the aircraft.
    This directive mandates incorporation of a new centering 
mechanism on the elevator torque tube to prevent these sustained 
oscillations.

Loss of pitch control could result in reduced controllability of the 
airplane.

Actions and Compliance

    (f) Unless already done, do the following actions.
    (1) Within 6,000 flight hours after the effective date of this 
AD, install a new PCU centering mechanism, in accordance with the 
Accomplishment Instructions of Bombardier Service Bulletin 670BA-27-
042, Revision B, dated June 2, 2009.
    (2) Incorporation of Bombardier Service Bulletin 670BA-27-042, 
dated October 14, 2008; or Revision A, dated January 8, 2009; before 
the effective date of this AD, is considered acceptable for 
compliance with this AD only if Bombardier Repair Engineering Order 
(REO) 670-27-31-001, dated January 12, 2009; or Bombardier Service 
Non-Incorporated Engineering Order (SNIEO) S01 or S02 from 
Bombardier Kit Drawing KBA670-93702, Revision C, dated January 28, 
2009; is incorporated at the same time.

FAA AD Differences

    Note 1:  This AD differs from the MCAI and/or service 
information as follows: No differences.

Other FAA AD Provisions

    (g) The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, New 
York Aircraft Certification Office, FAA, has the authority to 
approve AMOCs for this AD, if requested using the procedures found 
in 14 CFR 39.19. Send information to ATTN: Program Manager, 
Continuing Operational Safety, FAA, New York ACO, 1600 Stewart 
Avenue, Suite 410, Westbury, New York 11590; telephone 516-228-7300; 
fax 516-794-5531.

[[Page 63333]]

Before using any approved AMOC on any airplane to which the AMOC 
applies, notify your principal maintenance inspector (PMI) or 
principal avionics inspector (PAI), as appropriate, or lacking a 
principal inspector, your local Flight Standards District Office.
    (2) Airworthy Product: For any requirement in this AD to obtain 
corrective actions from a manufacturer or other source, use these 
actions if they are FAA-approved. Corrective actions are considered 
FAA-approved if they are approved by the State of Design Authority 
(or their delegated agent). You are required to assure the product 
is airworthy before it is returned to service.
    (3) Reporting Requirements: For any reporting requirement in 
this AD, under the provisions of the Paperwork Reduction Act (44 
U.S.C. 3501 et seq.), the Office of Management and Budget (OMB) has 
approved the information collection requirements and has assigned 
OMB Control Number 2120-0056.

Related Information

    (h) Refer to Canadian Airworthiness Directive CF-2009-28, issued 
June 29, 2009; and Bombardier Service Bulletin 670BA-27-042, 
Revision B, dated June 2, 2009; for related information.

    Issued in Renton, Washington, on November 23, 2009.
Ali Bahrami,
Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. E9-28859 Filed 12-2-09; 8:45 am]

BILLING CODE 4910-13-P
