
[Federal Register: October 19, 2009 (Volume 74, Number 200)]
[Proposed Rules]               
[Page 53440-53442]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr19oc09-23]                         

-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2009-0914; Directorate Identifier 2009-NM-122-AD]
RIN 2120-AA64

 
Airworthiness Directives; Airbus Model A330-200 and -300, and 
Model A340-300 Series Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to adopt a new airworthiness directive (AD) for the 
products listed above. This proposed AD results from mandatory 
continuing airworthiness information (MCAI) originated by an aviation 
authority of another country to identify and correct an unsafe 
condition on an aviation product. The MCAI describes the unsafe 
condition as:

    In the door 2 area, the hat-racks are supplied with a basic wire 
harness which includes ``Oxygen Masks'' activation.
    In case of a monument installation, the respective non-used hat-
rack connections between monument and outer skin are put on stow. It 
was noticed in production, that the distance between the stowed wire 
harness and the monument could be too small. This condition, if not 
corrected, could lead to the short circuit of wires dedicated to 
oxygen, which, in case of emergency, could result in a large number 
of passenger oxygen masks not being supplied with oxygen, possibly 
causing personal injuries.
* * * * *

The proposed AD would require actions that are intended to address the 
unsafe condition described in the MCAI.

DATES: We must receive comments on this proposed AD by December 3, 
2009.

ADDRESSES: You may send comments by any of the following methods:
     Federal eRulemaking Portal: Go to http://
www.regulations.gov. Follow the instructions for submitting comments.
     Fax: (202) 493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue, SE., Washington, DC 20590.
     Hand Delivery: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-40, 1200 New 
Jersey Avenue, SE., Washington, DC, between 9 a.m. and 5 p.m., Monday 
through Friday, except Federal holidays.
    For service information identified in this proposed AD, contact 
Airbus SAS--Airworthiness Office--EAL, 1 Rond Point Maurice Bellonte, 
31707 Blagnac Cedex, France; fax +33 5 61 93 45 80, e-mail 
airworthiness.A330-A340@airbus.com; Internet http://www.airbus.com. You 
may review copies of the referenced service information at the FAA, 
Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, 
Washington. For information on the availability of this material at the 
FAA, call 425-227-1221 or 425-227-1152.

Examining the AD Docket

    You may examine the AD docket on the Internet at http://
www.regulations.gov; or in person at the Docket Operations office 
between 9 a.m. and 5 p.m., Monday through Friday, except Federal 
holidays. The AD docket contains this proposed AD, the regulatory 
evaluation, any comments received, and other information. The street 
address for the Docket Operations office (telephone (800) 647-5527) is 
in the ADDRESSES section. Comments will be available in the AD docket 
shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Vladimir Ulyanov, Aerospace Engineer, 
International Branch, ANM-116, Transport Airplane Directorate, FAA, 
1601 Lind Avenue, SW., Renton, Washington 98057-3356; telephone (425) 
227-1138; fax (425) 227-1149.

SUPPLEMENTARY INFORMATION:

Comments Invited

    We invite you to send any written relevant data, views, or 
arguments about this proposed AD. Send your comments to an address 
listed under the ADDRESSES section. Include ``Docket No. FAA-2009-0914; 
Directorate Identifier 2009-NM-122-AD'' at the beginning of your 
comments. We specifically invite comments on the overall regulatory, 
economic, environmental, and energy aspects of this proposed AD. We 
will consider all comments received by the closing date and may amend 
this proposed AD based on those comments.

[[Page 53441]]

    We have lengthened the 30-day comment period for proposed ADs that 
address MCAI originated by aviation authorities of other countries to 
provide adequate time for interested parties to submit comments. The 
comment period for these proposed ADs is now typically 45 days, which 
is consistent with the comment period for domestic transport ADs.
    We will post all comments we receive, without change, to http://
www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this proposed AD.

Discussion

    The European Aviation Safety Agency (EASA), which is the Technical 
Agent for the Member States of the European Community, has issued EASA 
Airworthiness Directive 2009-0077, dated April 6, 2009 (referred to 
after this as ``the MCAI''), to correct an unsafe condition for the 
specified products. The MCAI states:

    In the door 2 area, the hat-racks are supplied with a basic wire 
harness which includes ``Oxygen Masks'' activation.
    In case of a monument installation, the respective non-used hat-
rack connections between monument and outer skin are put on stow. It 
was noticed in production, that the distance between the stowed wire 
harness and the monument could be too small. This condition, if not 
corrected, could lead to the short circuit of wires dedicated to 
oxygen, which, in case of emergency, could result in a large number 
of passenger oxygen masks not being supplied with oxygen, possibly 
causing personal injuries.
    For the reasons described above, this AD requires the 
modification of the hat rack connectors on stow, and the rerouting 
of the associated wire harness in case of monument installed in door 
2 area.

You may obtain further information by examining the MCAI in the AD 
docket.

Relevant Service Information

    Airbus has issued Mandatory Service Bulletins A330-92-3070, 
Revision 01, dated January 12, 2009; and A340-92-4073, Revision 01, 
dated January 13, 2009. The actions described in this service 
information are intended to correct the unsafe condition identified in 
the MCAI.

FAA's Determination and Requirements of This Proposed AD

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to our bilateral agreement with the State of Design Authority, we have 
been notified of the unsafe condition described in the MCAI and service 
information referenced above. We are proposing this AD because we 
evaluated all pertinent information and determined an unsafe condition 
exists and is likely to exist or develop on other products of the same 
type design.

Differences Between This AD and the MCAI or Service Information

    We have reviewed the MCAI and related service information and, in 
general, agree with their substance. But we might have found it 
necessary to use different words from those in the MCAI to ensure the 
AD is clear for U.S. operators and is enforceable. In making these 
changes, we do not intend to differ substantively from the information 
provided in the MCAI and related service information.
    We might also have proposed different actions in this AD from those 
in the MCAI in order to follow FAA policies. Any such differences are 
highlighted in a note within the proposed AD.

Costs of Compliance

    Based on the service information, we estimate that this proposed AD 
would affect about 43 products of U.S. registry. We also estimate that 
it would take about 3 work-hours per product to comply with the basic 
requirements of this proposed AD. The average labor rate is $80 per 
work-hour. Required parts costs are negligible. Where the service 
information lists required parts costs that are uncovered under 
warranty, we have assumed that there will be no charge for these costs. 
As we do not control warranty coverage for affected parties, some 
parties may incur costs higher than estimated here. Based on these 
figures, we estimate the cost of the proposed AD on U.S. operators to 
be $10,320, or $240 per product.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more detail the scope of the Agency's 
authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979); and
    3. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.
    We prepared a regulatory evaluation of the estimated costs to 
comply with this proposed AD and placed it in the AD docket.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

    1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

    2. The FAA amends Sec.  39.13 by adding the following new AD:

    Airbus: Docket No. FAA-2009-0914; Directorate Identifier 2009-
NM-122-AD.

Comments Due Date

    (a) We must receive comments by December 3, 2009.

Affected ADs

    (b) None.

Applicability

    (c) This AD applies to Airbus Model A330-201, -202, -203, -223, 
-243, -301, -302, -303, -321, -322, -323, -341, -342, and -343 
series airplanes; and Airbus Model A340-311, -312, and -313 series 
airplanes; certificated in any category, all manufacturer

[[Page 53442]]

serial numbers on which Airbus modification 48825 has been embodied 
in production, except those on which Airbus modification 57409 has 
been embodied in production.

Subject

    (d) Air Transport Association (ATA) of America Code 92.

Reason

    (e) The mandatory continuing airworthiness information (MCAI) 
states:
    In the door 2 area, the hat-racks are supplied with a basic wire 
harness which includes ``Oxygen Masks'' activation.
    In case of a monument installation, the respective non-used hat-
rack connections between monument and outer skin are put on stow. It 
was noticed in production, that the distance between the stowed wire 
harness and the monument could be too small. This condition, if not 
corrected, could lead to the short circuit of wires dedicated to 
oxygen, which, in case of emergency, could result in a large number 
of passenger oxygen masks not being supplied with oxygen, possibly 
causing personal injuries.
    For the reasons described above, this AD requires the 
modification of the hat rack connectors on stow, and the rerouting 
of the associated wire harness in case of monument installed in door 
2 area.

Actions and Compliance

    (f) Unless already done, do the following actions.
    (1) Within 24 months after the effective date of this AD, modify 
both the left-hand (L/H) and right-hand (R/H) hat-rack connectors in 
accordance with the Accomplishment Instructions of Airbus Mandatory 
Service Bulletin A330-92-3070, Revision 01, dated January 12, 2009; 
or Airbus Mandatory Service Bulletin A340-92-4073, Revision 01, 
dated January 13, 2009; as applicable, except as provided by 
paragraph (f)(2) of this AD.
    (2) Modifications done before the effective date of this AD, in 
accordance with the Accomplishment Instructions of Airbus Mandatory 
Service Bulletin A330-92-3070 or A340-92-4073, both dated July 10, 
2008, as applicable, are acceptable for compliance with the 
applicable requirements of paragraph (f)(1) of this AD, provided 
that within 24 months after the effective date of this AD, the 
``ADDITIONAL WORK'' specified in Airbus Mandatory Service Bulletin 
A330-92-3070, Revision 01, dated January 12, 2009; or Airbus 
Mandatory Service Bulletin A340-92-4073, Revision 01, dated January 
13, 2009; as applicable; is accomplished in accordance with the 
Accomplishment Instructions of Airbus Mandatory Service Bulletin 
A330-92-3070, Revision 01, dated January 12, 2009; or Airbus 
Mandatory Service Bulletin A340-92-4073, Revision 01, dated January 
13, 2009; as applicable.

FAA AD Differences

    Note 1:  This AD differs from the MCAI and/or service 
information as follows: No differences.

Other FAA AD Provisions

    (g) The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Branch, ANM-116, Transport Airplane Directorate, FAA, 
has the authority to approve AMOCs for this AD, if requested using 
the procedures found in 14 CFR 39.19. Send information to ATTN: 
Vladimir Ulyanov, Aerospace Engineer, International Branch, ANM-116, 
Transport Airplane Directorate, FAA, 1601 Lind Avenue, SW., Renton, 
Washington 98057-3356; telephone (425) 227-1138; fax (425) 227-1149. 
Before using any approved AMOC on any airplane to which the AMOC 
applies, notify your principal maintenance inspector (PMI) or 
principal avionics inspector (PAI), as appropriate, or lacking a 
principal inspector, your local Flight Standards District Office. 
The AMOC approval letter must specifically reference this AD.
    (2) Airworthy Product: For any requirement in this AD to obtain 
corrective actions from a manufacturer or other source, use these 
actions if they are FAA-approved. Corrective actions are considered 
FAA-approved if they are approved by the State of Design Authority 
(or their delegated agent). You are required to assure the product 
is airworthy before it is returned to service.
    (3) Reporting Requirements: For any reporting requirement in 
this AD, under the provisions of the Paperwork Reduction Act, the 
Office of Management and Budget (OMB) has approved the information 
collection requirements and has assigned OMB Control Number 2120-
0056.

Related Information

    (h) Refer to MCAI European Aviation Safety Agency Airworthiness 
Directive 2009-0077, dated April 6, 2009; Airbus Mandatory Service 
Bulletin A330-92-3070, Revision 01, dated January 12, 2009; and 
Airbus Mandatory Service Bulletin A340-92-4073, Revision 01, dated 
January 13, 2009; for related information.


    Issued in Renton, Washington, on October 5, 2009.
Ali Bahrami,
Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. E9-24988 Filed 10-16-09; 8:45 am]

BILLING CODE 4910-13-P
