
[Federal Register: July 15, 2009 (Volume 74, Number 134)]
[Rules and Regulations]               
[Page 34221-34222]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr15jy09-6]                         


[[Page 34221]]

-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2009-0330; Directorate Identifier 2008-NE-43-AD; 
Amendment 39-15961; AD 2009-14-11]
RIN 2120-AA64

 
Airworthiness Directives; Turbomeca S.A. ARRIUS 2F Turboshaft 
Engines

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: We are adopting a new airworthiness directive (AD) for the 
products listed above. This AD results from mandatory continuing 
airworthiness information (MCAI) issued by an aviation authority of 
another country to identify and correct an unsafe condition on an 
aviation product. The MCAI describes the unsafe condition as:

    On several ARRIUS 2F engines, the clearance between the P3 air 
pipe P/N 0319719180 and the rear right bulkhead P/N 0319998240 has 
been found to be too small.
    Investigations have shown that both P3 air pipe and rear right 
bulkhead were compliant to the design. The Turbomeca Engineering 
Department concluded that the tolerance of assembly established 
during the design could result in some rubbing between parts.
    Rubs between the pipe and the bulkhead may lead to premature 
wearing and finally rupture of the P3 air pipe. The loss of P3 air 
pressure would then force the fuel control system to idle which 
could have a detrimental effect in critical phases of flight.

    We are issuing this AD to prevent an uncommanded power loss, which 
could result in an emergency autorotation landing or accident.

DATES: This AD becomes effective August 19, 2009. The Director of the 
Federal Register approved the incorporation by reference of certain 
publications listed in this AD as of August 19, 2009.

ADDRESSES: The Docket Operations office is located at Docket Management 
Facility, U.S. Department of Transportation, 1200 New Jersey Avenue, 
SE., West Building Ground Floor, Room W12-140, Washington, DC 20590-
0001.

FOR FURTHER INFORMATION CONTACT: James Lawrence, Aerospace Engineer, 
Engine Certification Office, FAA, Engine and Propeller Directorate, 12 
New England Executive Park, Burlington, MA 01803; e-mail: 
james.lawrence@faa.gov; telephone (781) 238-7176; fax (781) 238-7199.

SUPPLEMENTARY INFORMATION: 

Discussion

    We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR 
part 39 to include an AD that would apply to the specified products. 
That NPRM was published in the Federal Register on April 13, 2009 (74 
FR 16809). That NPRM proposed to correct an unsafe condition for the 
specified products. The MCAI states that:

    On several ARRIUS 2F engines, the clearance between the P3 air 
pipe P/N 0319719180 and the rear right bulkhead P/N 0319998240 has 
been found to be too small.
    Investigations have shown that both P3 air pipe and rear right 
bulkhead were compliant to the design. The Turbomeca Engineering 
Department concluded that the tolerance of assembly established 
during the design could result in some rubbing between parts.
    Rubs between the pipe and the bulkhead may lead to premature 
wearing and finally rupture of the P3 air pipe. The loss of P3 air 
pressure would then force the fuel control system to idle which 
could have a detrimental effect in critical phases of flight.

Comments

    We gave the public the opportunity to participate in developing 
this AD. We received no comments on the NPRM or on the determination of 
the cost to the public.

Conclusion

    We reviewed the available data and determined that air safety and 
the public interest require adopting the AD as proposed.

Costs of Compliance

    Based on the service information, we estimate that this AD will 
affect about 94 engines installed on helicopters of U.S. registry. We 
also estimate that it will take about 1 work-hour per engine to comply 
with this AD. The average labor rate is $80 per work-hour. Required 
parts will cost about $705 per engine. Based on these figures, we 
estimate the cost of the AD on U.S. operators to be $73,790. Our cost 
estimate is exclusive of possible warranty coverage.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more detail the scope of the Agency's 
authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this AD will not have federalism implications 
under Executive Order 13132. This AD will not have a substantial direct 
effect on the States, on the relationship between the national 
government and the States, or on the distribution of power and 
responsibilities among the various levels of government.
    For the reasons discussed above, I certify this AD:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979); and
    3. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.
    We prepared a regulatory evaluation of the estimated costs to 
comply with this AD and placed it in the AD docket.

Examining the AD Docket

    You may examine the AD docket on the Internet at http://
www.regulations.gov; or in person at the Docket Operations office 
between 9 a.m. and 5 p.m., Monday through Friday, except Federal 
holidays. The AD docket contains this AD, the regulatory evaluation, 
any comments received, and other information. The street address for 
the Docket Operations office (telephone (800) 647-5527) is provided in 
the ADDRESSES section. Comments will be available in the AD docket 
shortly after receipt.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

0
Accordingly, under the authority delegated to me by the Administrator, 
the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.

[[Page 34222]]

Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new AD:

2009-14-11 Turbomeca S.A.: Amendment 39-15961. Docket No. FAA-2009-
0330; Directorate Identifier 2008-NE-43-AD.

Effective Date

    (a) This airworthiness directive (AD) becomes effective August 
19, 2009.

Affected ADs

    (b) None.

Applicability

    (c) This AD applies to Turbomeca S.A. ARRIUS 2F turboshaft 
engines with P3 air pipe, part number 0319719180, installed. These 
engines are installed on, but not limited to, Eurocopter EC120B 
helicopters.

Reason

    (d) Rubs between the pipe and the bulkhead may lead to premature 
wearing and finally rupture of the P3 air pipe. The loss of P3 air 
pressure would then force the fuel control system to idle which 
could have a detrimental effect in critical phases of flight.
    We are issuing this AD to prevent an uncommanded power loss, 
which could result in an emergency autorotation landing or accident.

Actions and Compliance

    (e) Unless already done, do the following actions within 100 
operating hours after the effective date of this AD. Use paragraphs 
2.B.(1) through 2.C.(2) of Turbomeca Mandatory Service Bulletin No. 
319 75 4810, dated May 14, 2008.
    (1) Visually inspect P3 air pipe (first section) and RH rear 
half-wall.
    (2) Inspect play between P3 air pipe (first section) and RH rear 
half-wall.
    (3) Replace P3 air pipe (first section) if any damage is found.
    (4) Readjust the first section of the P3 air pipe if the 
inspected clearance is found to be not compliant.
    (5) If the play after readjusting the first section of the P3 
air pipe is still less than 0.5 mm, repeat paragraphs (e)(1) through 
(e)(4) of this AD within intervals of 100 hours time-since-last 
inspection.
    (6) Replace RH rear half-wall if any damage is found.

FAA AD Differences

    (f) None.

Other FAA AD Provisions

    (g) Alternative Methods of Compliance (AMOCs): The Manager, 
Engine Certification Office, FAA, has the authority to approve AMOCs 
for this AD, if requested using the procedures found in 14 CFR 
39.19.

Related Information

    (h) Refer to MCAI EASA Airworthiness Directive 2008-0134R1, 
dated February 17, 2009, and Turbomeca S.A. Mandatory Service 
Bulletin No. 319 75 4810, dated May 14, 2008, for related 
information. Contact Turbomeca, 40220 Tarnos, France; telephone 33 
(0)5 59 74 40 00; telex 570 042; fax 33 (0)5 59 74 45 15, for a copy 
of this service information.
    (i) Contact James Lawrence, Aerospace Engineer, Engine 
Certification Office, FAA, Engine and Propeller Directorate, 12 New 
England Executive Park, Burlington, MA 01803; e-mail: 
james.lawrence@faa.gov; telephone (781) 238-7176; fax (781) 238-
7199, for more information about this AD.

Material Incorporated by Reference

    (j) You must use Turbomeca Mandatory Service Bulletin No. 319 75 
4810, dated May 14, 2008 to do the actions required by this AD, 
unless the AD specifies otherwise.
    (1) The Director of the Federal Register approved the 
incorporation by reference of this service information under 5 
U.S.C. 552(a) and 1 CFR part 51.
    (2) For service information identified in this AD, contact 
Turbomeca, 40220 Tarnos, France; telephone 33 (0)5 59 74 40 00; 
telex 570 042; fax 33 (0)5 59 74 45 15.
    (3) You may review copies at the FAA, New England Region, 12 New 
England Executive Park, Burlington, MA; or at the National Archives 
and Records Administration (NARA). For information on the 
availability of this material at NARA, call (202) 741-6030, or go 
to: http://www.archives.gov/federal-register/cfr/ibr-locations.html.

    Issued in Burlington, Massachusetts, on June 30, 2009.
Francis A. Favara,
Manager, Engine and Propeller Directorate, Aircraft Certification 
Service.
 [FR Doc. E9-16113 Filed 7-14-09; 8:45 am]

BILLING CODE 4910-13-P
