

[Federal Register: February 5, 2008 (Volume 73, Number 24)]
[Proposed Rules]               
[Page 6640-6642]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr05fe08-28]                         

-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2008-0115; Directorate Identifier 2007-NM-240-AD]
RIN 2120-AA64

 
Airworthiness Directives; Saab Model SAAB 2000 Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to adopt a new airworthiness directive (AD) for the 
products listed above. This proposed AD results from mandatory 
continuing airworthiness information (MCAI) originated by an aviation 
authority of another country to identify and correct an unsafe 
condition on an aviation product. The MCAI describes the unsafe 
condition as:

    One LM-219-92 Centre Bracket from an LM-219-SA28 Aft Engine 
Mounting assembly was found to be cracked while installed on the 
aircraft.
    This reduces the effectiveness of the mounting assembly and 
could eventually cause it to fail.
* * * * *
    A failed mounting assembly, if not corrected, could result in loss 
of the engine. The proposed AD would require actions that are intended 
to address the unsafe condition described in the MCAI.

DATES: We must receive comments on this proposed AD by March 6, 2008.

ADDRESSES: You may send comments by any of the following methods:
     Federal eRulemaking Portal: Go to http://www.regulations.gov.
 Follow the instructions for submitting comments.

     Fax: (202) 493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue, SE., Washington, DC 20590.
     Hand Delivery: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-40, 1200 New 
Jersey Avenue, SE., Washington, DC, between 9 a.m. and 5 p.m., Monday 
through Friday, except Federal holidays.

Examining the AD Docket

    You may examine the AD docket on the Internet at http://www.regulations.gov
; or in person at the Docket Operations office 

between 9 a.m. and 5 p.m., Monday through Friday, except Federal 
holidays. The AD docket contains this proposed AD, the regulatory 
evaluation, any comments received, and other information. The street 
address for the Docket Operations office (telephone (800) 647-5527) is 
in the ADDRESSES section. Comments will be available in the AD docket 
shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Shahram Daneshmandi, Aerospace 
Engineer, International Branch, ANM-116, Transport Airplane 
Directorate, FAA, 1601 Lind Avenue, SW., Renton, Washington 98057-3356; 
telephone (425) 227-1112; fax (425) 227-1149.

SUPPLEMENTARY INFORMATION:

Comments Invited

    We invite you to send any written relevant data, views, or 
arguments about this proposed AD. Send your comments to an address 
listed under the ADDRESSES section. Include ``Docket No. FAA-2008-0115; 
Directorate Identifier 2007-NM-240-AD'' at the beginning of your 
comments. We specifically invite comments on the overall regulatory, 
economic, environmental, and energy aspects of this proposed AD. We 
will consider all comments received by the closing date and may amend 
this proposed AD based on those comments.
    We will post all comments we receive, without change, to http://www.regulations.gov
, including any personal information you provide. We 

will also post a report summarizing each substantive verbal contact we 
receive about this proposed AD.

Discussion

    The European Aviation Safety Agency (EASA), which is the Technical 
Agent for the Member States of the European Community, has issued EASA

[[Page 6641]]

Airworthiness Directive 2007-0204, dated August 8, 2007 (referred to 
after this as ``the MCAI''), to correct an unsafe condition for the 
specified products. The MCAI states:

    One LM-219-92 Centre Bracket from an LM-219-SA28 Aft Engine 
Mounting assembly was found to be cracked while installed on the 
aircraft.
    This reduces the effectiveness of the mounting assembly and 
could eventually cause it to fail.
    This AD requires rework in order to make the centre bracket less 
sensitive to external damage that may result in a crack.

A failed mounting assembly, if not corrected, could result in loss of 
the engine. The corrective action also includes a visual and 
fluorescent penetrant inspection for cracking of the center bracket of 
the aft engine mounting assembly for both engines, re-identification of 
a reworked center bracket, additional fluorescent penetrant inspections 
for cracking of the reworked center bracket, and replacement of the aft 
engine mounting assembly if any cracked center bracket is found. You 
may obtain further information by examining the MCAI in the AD docket.

Relevant Service Information

    Saab has issued Saab 2000 Service Bulletin 2000-71-025, dated June 
13, 2007. The actions described in this service information are 
intended to correct the unsafe condition identified in the MCAI.

FAA's Determination and Requirements of This Proposed AD

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to our bilateral agreement with the State of Design Authority, we have 
been notified of the unsafe condition described in the MCAI and service 
information referenced above. We are proposing this AD because we 
evaluated all pertinent information and determined an unsafe condition 
exists and is likely to exist or develop on other products of the same 
type design.

Differences Between This AD and the MCAI or Service Information

    We have reviewed the MCAI and related service information and, in 
general, agree with their substance. But we might have found it 
necessary to use different words from those in the MCAI to ensure the 
AD is clear for U.S. operators and is enforceable. In making these 
changes, we do not intend to differ substantively from the information 
provided in the MCAI and related service information.
    We might also have proposed different actions in this AD from those 
in the MCAI in order to follow FAA policies. Any such differences are 
highlighted in a NOTE within the proposed AD.

Costs of Compliance

    Based on the service information, we estimate that this proposed AD 
would affect about 6 products of U.S. registry. We also estimate that 
it would take about 8 work-hours per product to comply with the basic 
requirements of this proposed AD. The average labor rate is $80 per 
work-hour. Based on these figures, we estimate the cost of the proposed 
AD on U.S. operators to be $3,840, or $640 per product.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more detail the scope of the Agency's 
authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979); and
    3. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.
    We prepared a regulatory evaluation of the estimated costs to 
comply with this proposed AD and placed it in the AD docket.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

    1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

    2. The FAA amends Sec.  39.13 by adding the following new AD:

SAAB Aircraft AB: Docket No. FAA-2008-0115; Directorate Identifier 
2007-NM-240-AD.

Comments Due Date

    (a) We must receive comments by March 6, 2008.

Affected ADs

    (b) None.

Applicability

    (c) This AD applies to Saab Model SAAB 2000 airplanes, 
certificated in any category, serial number 004 through 063.

Subject

    (d) Air Transport Association (ATA) of America Code 71: Power 
Plant.

Reason

    (e) The mandatory continuing airworthiness information (MCAI) 
states:

    One LM-219-92 Centre Bracket from an LM-219-SA28 Aft Engine 
Mounting assembly was found to be cracked while installed on the 
aircraft.
    This reduces the effectiveness of the mounting assembly and 
could eventually cause it to fail.
    This AD requires rework in order to make the centre bracket less 
sensitive to external damage that may result in a crack.

A failed mounting assembly, if not corrected, could result in loss 
of the engine. The corrective action also includes a visual and 
fluorescent penetrant inspection for cracking of the center bracket 
of the aft engine mounting assembly for both engines, re-
identification of a reworked center bracket, additional fluorescent 
penetrant inspections for cracking of the reworked center bracket, 
and replacement of the aft engine mounting assembly if any cracked 
center bracket is found.

Actions and Compliance

    (f) Unless already done, do the following actions in accordance 
with the

[[Page 6642]]

Accomplishment Instructions of Saab 2000 Service Bulletin 2000-71-
025, dated June 13, 2007.
    (1) Within 1,000 flight hours after the effective date of this 
AD, do a visual and a fluorescent penetrant inspection for cracking 
of the center bracket of both of the aft engine mounting assemblies.
    (2) If no cracking is found during the inspections required by 
paragraph (f)(1) of this AD, within 4,000 flight hours after the 
effective date of this AD, rework the center bracket of the aft 
engine mounting assembly, do fluorescent penetrant inspections for 
cracking of the reworked bracket, and re-identify with new part 
numbers the reworked center bracket and the applicable aft engine 
mounting assembly.
    (3) If any cracking is found during any inspection required by 
paragraph (f)(1) or (f)(2) of this AD, before further flight, 
replace the aft engine mounting assembly, and rework and re-identify 
the center bracket.

FAA AD Differences

    Note: This AD differs from the MCAI and/or service information 
as follows:
    (1) Although the MCAI or service information allows further 
flight after cracks are found during compliance with the required 
action, paragraph (f)(3) of this AD requires that you replace the 
aft engine mounting assembly before further flight.

Other FAA AD Provisions

    (g) The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Branch, Transport Airplane Directorate, ANM-116, FAA, 
has the authority to approve AMOCs for this AD, if requested using 
the procedures found in 14 CFR 39.19. Send information to ATTN: 
Shahram Daneshmandi, Aerospace Engineer, International Branch, ANM-
116, Transport Airplane Directorate, FAA, 1601 Lind Avenue, SW., 
Renton, Washington 98057-3356; telephone (425) 227-1112; fax (425) 
227-1149. Before using any approved AMOC on any airplane to which 
the AMOC applies, notify your appropriate principal inspector (PI) 
in the FAA Flight Standards District Office (FSDO), or lacking a PI, 
your local FSDO.
    (2) Airworthy Product: For any requirement in this AD to obtain 
corrective actions from a manufacturer or other source, use these 
actions if they are FAA-approved. Corrective actions are considered 
FAA-approved if they are approved by the State of Design Authority 
(or their delegated agent). You are required to assure the product 
is airworthy before it is returned to service.
    (3) Reporting Requirements: For any reporting requirement in 
this AD, under the provisions of the Paperwork Reduction Act, the 
Office of Management and Budget (OMB) has approved the information 
collection requirements and has assigned OMB Control Number 2120-
0056.

Related Information

    (h) Refer to MCAI European Aviation Safety Agency (EASA) 
Airworthiness Directive 2007-0204, dated August 8, 2007, and Saab 
2000 Service Bulletin 2000-71-025, dated June 13, 2007, for related 
information.

    Issued in Renton, Washington, on January 24, 2008.
Ali Bahrami,
Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
 [FR Doc. E8-1992 Filed 2-4-08; 8:45 am]

BILLING CODE 4910-13-P
