

[Federal Register: November 6, 2007 (Volume 72, Number 214)]
[Rules and Regulations]               
[Page 62559-62560]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr06no07-1]                         


========================================================================
Rules and Regulations
                                                Federal Register
________________________________________________________________________

This section of the FEDERAL REGISTER contains regulatory documents 
having general applicability and legal effect, most of which are keyed 
to and codified in the Code of Federal Regulations, which is published 
under 50 titles pursuant to 44 U.S.C. 1510.

The Code of Federal Regulations is sold by the Superintendent of Documents. 
Prices of new books are listed in the first FEDERAL REGISTER issue of each 
week.

========================================================================



[[Page 62559]]



DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2007-29066; Directorate Identifier 2007-NM-147-AD; 
Amendment 39-15250; AD 2007-23-04]
RIN 2120-AA64

 
Airworthiness Directives; Bombardier Model DHC-8-102, -103, -106, 
-201, -202, -301, -311, and -315 Airplanes

AGENCY: Federal Aviation Administration (FAA), Department of 
Transportation (DOT).

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: We are adopting a new airworthiness directive (AD) for the 
products listed above. This AD results from mandatory continuing 
airworthiness information (MCAI) originated by an aviation authority of 
another country to identify and correct an unsafe condition on an 
aviation product. The MCAI describes the unsafe condition as:

    It has been discovered in several cases that clamp bolts of the 
elevator spring tab mechanism were not installed in the correct 
orientation. Bolts have been found installed with bolt heads on the 
lower position and in two cases, some bolts, nuts and washers 
[hardware] were found to be loose or missing. Detachment of an 
elevator spring tab mechanism clamp bolt could lead to jamming of 
the elevator control system and reduced controllability of the 
aircraft.

We are issuing this AD to require actions to correct the unsafe 
condition on these products.

DATES: This AD becomes effective December 11, 2007.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in this AD as of December 11, 
2007.

ADDRESSES: You may examine the AD docket on the Internet at http://www.regulations.gov
 or in person at the U.S. Department of 

Transportation, Docket Operations, M-30, West Building Ground Floor, 
Room W12-140, 1200 New Jersey Avenue, SE., Washington, DC.

FOR FURTHER INFORMATION CONTACT: Dan Parrillo, Aerospace Engineer, 
Systems and Flight Test Branch, ANE-172, FAA, New York Aircraft 
Certification Office, 1600 Stewart Avenue, Suite 410, Westbury, New 
York 11590; telephone (516) 228-7305; fax (516) 794-5531.

SUPPLEMENTARY INFORMATION:

Discussion

    We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR 
part 39 to include an AD that would apply to the specified products. 
That NPRM was published in the Federal Register on August 31, 2007 (72 
FR 50288). That NPRM proposed to correct an unsafe condition for the 
specified products. The MCAI states:

    It has been discovered in several cases that clamp bolts of the 
elevator spring tab mechanism were not installed in the correct 
orientation. Bolts have been found installed with bolt heads on the 
lower position and in two cases, some bolts, nuts and washers 
[hardware] were found to be loose or missing. Detachment of an 
elevator spring tab mechanism clamp bolt could lead to jamming of 
the elevator control system and reduced controllability of the 
aircraft.

The corrective action is a one-time inspection of the left- and right-
hand elevator spring tab mechanism hardware for correct installation, 
and prior to further flight, installing new hardware for any hardware 
that is incorrectly installed. You may obtain further information by 
examining the MCAI in the AD docket.

Comments

    We gave the public the opportunity to participate in developing 
this AD. We received no comments on the NPRM or on the determination of 
the cost to the public.

Conclusion

    We reviewed the available data and determined that air safety and 
the public interest require adopting the AD as proposed.

Differences Between This AD and the MCAI or Service Information

    We have reviewed the MCAI and related service information and, in 
general, agree with their substance. But we might have found it 
necessary to use different words from those in the MCAI to ensure the 
AD is clear for U.S. operators and is enforceable. In making these 
changes, we do not intend to differ substantively from the information 
provided in the MCAI and related service information.
    We might also have required different actions in this AD from those 
in the MCAI in order to follow our FAA policies. Any such differences 
are highlighted in a Note within the AD.

Costs of Compliance

    We estimate that this AD will affect about 150 products of U.S. 
registry. We also estimate that it will take about 3 work-hours per 
product to comply with the basic requirements of this AD. The average 
labor rate is $80 per work-hour. Required parts will cost about $0 per 
product. Where the service information lists required parts costs that 
are covered under warranty, we have assumed that there will be no 
charge for these parts. As we do not control warranty coverage for 
affected parties, some parties may incur costs higher than estimated 
here. Based on these figures, we estimate the cost of this AD to the 
U.S. operators to be $36,000, or $240 per product.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more detail the scope of the Agency's 
authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this AD will not have federalism implications 
under

[[Page 62560]]

Executive Order 13132. This AD will not have a substantial direct 
effect on the States, on the relationship between the national 
government and the States, or on the distribution of power and 
responsibilities among the various levels of government.
    For the reasons discussed above, I certify this AD:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979); and
    3. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.
    We prepared a regulatory evaluation of the estimated costs to 
comply with this AD and placed it in the AD docket.

Examining the AD Docket

    You may examine the AD docket on the Internet at http://www.regulations.gov
; or in person at the Docket Operations office 

between 9 a.m. and 5 p.m., Monday through Friday, except Federal 
holidays. The AD docket contains the NPRM, the regulatory evaluation, 
any comments received, and other information. The street address for 
the Docket Operations office (telephone (800) 647-5527) is in the 
ADDRESSES section. Comments will be available in the AD docket shortly 
after receipt.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

0
Accordingly, under the authority delegated to me by the Administrator, 
the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]


0
2. The FAA amends Sec.  39.13 by adding the following new AD:

2007-23-04 Bombardier, Inc. (Formerly de Havilland, Inc.): Amendment 
39-15250. Docket No. FAA-2007-29066; Directorate Identifier 2007-NM-
147-AD.

Effective Date

    (a) This airworthiness directive (AD) becomes effective December 
11, 2007.

Affected ADs

    (b) None.

Applicability

    (c) This AD applies to Bombardier Model DHC-8-102, -103, -106, -
201, -202, -301, -311, and -315 airplanes; certificated in any 
category; serial numbers 003 through 611 inclusive.

Subject

    (d) Air Transport Association (ATA) of America Code 27: Flight 
controls.

Reason

    (e) The mandatory continuing airworthiness information (MCAI) 
states:

    It has been discovered in several cases that clamp bolts of the 
elevator spring tab mechanism were not installed in the correct 
orientation. Bolts have been found installed with bolt heads on the 
lower position and in two cases, some bolts, nuts and washers 
[hardware] were found to be loose or missing. Detachment of an 
elevator spring tab mechanism clamp bolt could lead to jamming of 
the elevator control system and reduced controllability of the 
aircraft.

    The corrective action is a one-time inspection of the left- and 
right-hand elevator spring tab mechanism hardware for correct 
installation, and prior to further flight, installing new hardware 
for any hardware that is incorrectly installed.

Actions and Compliance

    (f) Unless already done, do the following actions.
    (1) Within 12 months after the effective date of this AD: Carry 
out a one-time inspection of the left- and right-hand elevator 
spring tab mechanism hardware for correct installation according to 
the Accomplishment Instructions of Bombardier Service Bulletin 8-27-
106, dated February 7, 2006.
    (2) If any hardware is found incorrectly installed during the 
inspection required by paragraph (f)(1) of this AD, prior to further 
flight, install new hardware according to the Accomplishment 
Instructions of Bombardier Service Bulletin 8-27-106, dated February 
7, 2006.

FAA AD Differences

    Note: This AD differs from the MCAI and/or service information 
as follows: No differences.

Other FAA AD Provisions

    (g) The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, New 
York Aircraft Certification Office, FAA, has the authority to 
approve AMOCs for this AD, if requested using the procedures found 
in 14 CFR 39.19. Send information to ATTN: Dan Parrillo, Aerospace 
Engineer, Systems and Flight Test Branch, ANE-172, FAA, New York 
Aircraft Certification Office, 1600 Stewart Avenue, Suite 410, 
Westbury, New York 11590; telephone (516) 228-7305; fax (516) 794-
5531. Before using any approved AMOC on any airplane to which the 
AMOC applies, notify your appropriate principal inspector (PI) in 
the FAA Flight Standards District Office (FSDO), or lacking a PI, 
your local FSDO.
    (2) Airworthy Product: For any requirement in this AD to obtain 
corrective actions from a manufacturer or other source, use these 
actions if they are FAA-approved. Corrective actions are considered 
FAA-approved if they are approved by the State of Design Authority 
(or their delegated agent). You are required to assure the product 
is airworthy before it is returned to service.
    (3) Reporting Requirements: For any reporting requirement in 
this AD, under the provisions of the Paperwork Reduction Act, the 
Office of Management and Budget (OMB) has approved the information 
collection requirements and has assigned OMB Control Number 2120-
0056.

Related Information

    (h) Refer to MCAI Canadian Airworthiness Directive CF-2007-08, 
dated June 4, 2007, and Bombardier Service Bulletin 8-27-106, dated 
February 7, 2006, for related information.

Material Incorporated by Reference

    (i) You must use Bombardier Service Bulletin 8-27-106, dated 
February 7, 2006, to do the actions required by this AD, unless the 
AD specifies otherwise.
    (1) The Director of the Federal Register approved the 
incorporation by reference of this service information under 5 
U.S.C. 552(a) and 1 CFR part 51.
    (2) For service information identified in this AD, contact 
Bombardier, Inc., Bombardier Regional Aircraft Division, 123 Garratt 
Boulevard, Downsview, Ontario M3K 1Y5, Canada.
    (3) You may review copies at the FAA, Transport Airplane 
Directorate, 1601 Lind Avenue, SW., Renton, Washington; or at the 
National Archives and Records Administration (NARA). For information 
on the availability of this material at NARA, call (202) 741-6030, 
or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html
.


    Issued in Renton, Washington, on October 27, 2007.
Stephen P. Boyd,
Assistant Manager, Transport Airplane Directorate, Aircraft 
Certification Service.
[FR Doc. E7-21672 Filed 11-5-07; 8:45 am]

BILLING CODE 4910-13-P
