

[Federal Register: November 16, 2007 (Volume 72, Number 221)]
[Proposed Rules]               
[Page 64542-64545]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr16no07-15]                         

-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2007-0178; Directorate Identifier 2007-SW-20-AD]
RIN 2120-AA64

 
Airworthiness Directives; Bell Helicopter Textron Canada (BHTC) 
Model 222, 222B, and 222U Helicopters

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to adopt a new airworthiness directive (AD) for 
BHTC Model 222, 222B, and 222U helicopters. This proposed AD results 
from mandatory continuing airworthiness information (MCAI) originated 
by an aviation authority of another country to identify and correct an 
unsafe condition on an aviation product. The aviation

[[Page 64543]]

authority of Canada, with which we have a bilateral agreement, states 
in the MCAI:

    It has been determined that the existing rigging procedures for 
the tail rotor pitch change mechanism have to be changed due to 
possibility of parts interference.

The cumulative effect of individual part tolerances resulting in the 
total assemblage of those parts being out of tolerance could result in 
the tail rotor yoke striking another part other than the flapping stop 
(parts interference) cited in the MCAI. Also, the misalignment of the 
tail rotor counterweight bellcrank may result in higher tail rotor 
pedal forces and a higher pilot workload after failure of the No. 1 
hydraulic system. Both parts interference and the misaligned 
counterweight bellcrank create an unsafe condition. The proposed AD 
would require actions that are intended to address these unsafe 
conditions.

DATES: We must receive comments on this proposed AD by December 17, 
2007.

ADDRESSES: You may send comments by any of the following methods:
     Federal eRulemaking Portal: Go to http://www.regulations.gov.
 Follow the instructions for submitting comments.

     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue, SE., Washington, DC 20590.
     Hand Delivery: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue, SE., Washington, DC 20590, between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays.

Examining the AD Docket

    You may examine the AD docket on the Internet at http://www.regulations.gov
, or in person at the Docket Operations office 

between 9 a.m. and 5 p.m., Monday through Friday, except Federal 
holidays. The AD docket contains this proposed AD, the economic 
evaluation, any comments received, and other information. The street 
address for the Docket Operations office (telephone (800) 647-5527) is 
in the ADDRESSES section. Comments will be available in the AD docket 
shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Tyrone Millard, Aviation Safety 
Engineer, FAA, Rotorcraft Directorate, Rotorcraft Standards Staff, Fort 
Worth, Texas 76193-0111, telephone (817) 222-5439, fax (817) 222-5961.

SUPPLEMENTARY INFORMATION: 

Streamlined Issuance of AD

    The FAA is implementing a new process for streamlining the issuance 
of ADs related to MCAI. This streamlined process will allow us to adopt 
MCAI safety requirements in a more efficient manner and will reduce 
safety risks to the public. This process continues to follow all FAA AD 
issuance processes to meet legal, economic, Administrative Procedure 
Act, and Federal Register requirements. We also continue to meet our 
technical decision-making responsibilities to identify and correct 
unsafe conditions on U.S.-certificated products.
    This proposed AD references the MCAI and related service 
information that we considered in forming the engineering basis to 
correct the unsafe condition. The proposed AD contains text copied from 
the MCAI and for this reason might not follow our plain language 
principles.

Comments Invited

    We invite you to send any written relevant data, views, or 
arguments about this proposed AD. Send your comments to an address 
listed under the ADDRESSES section. Include ``Docket No. FAA-2007-0178; 
Directorate Identifier 2007-SW-20-AD'' at the beginning of your 
comments. We specifically invite comments on the overall regulatory, 
economic, environmental, and energy aspects of this proposed AD. We 
will consider all comments received by the closing date and may amend 
this proposed AD based on those comments.
    We will post all comments we receive, without change, to http://www.regulations.gov
, including any personal information you provide. We 

will also post a report summarizing each substantive verbal contact we 
receive about this proposed AD.

Discussion

    Transport Canada, which is the aviation authority for Canada, has 
issued Canadian Airworthiness Directive No. CF-2007-07, dated April 11, 
2007 (referred to after this as ``the MCAI''), to correct an unsafe 
condition for the Canadian-certificated products. The MCAI states:

    It has been determined that the existing rigging procedures for 
the tail rotor pitch change mechanism have to be changed due to 
possibility of parts interference.

    Because the cumulative effect of the tolerances on the various 
parts may result in the total assemblage outboard of the counterweight 
bellcrank being out of tolerance, the tail rotor yoke may contact nut, 
P/N 222-012-731-001, before contacting the flapping stop, resulting in 
less tail rotor travel. Additionally, the manufacturer has indicated 
that the tail rotor counterweight bellcranks may be misaligned 
resulting in higher tail rotor pedal forces and higher pilot workload 
after failure of the No. 1 hydraulic system. Both the parts 
interference and the higher pedal forces constitute unsafe conditions.
    You may obtain further information by examining the service 
information and the MCAI in the AD docket.

Relevant Service Information

    Bell Helicopter Textron has issued Alert Service Bulletin (ASB) 
222-07-104 and ASB 222U-07-75, both dated January 9, 2007. The actions 
described in the MCAI are intended to correct the same unsafe condition 
as that identified in the service information.

FAA's Determination and Requirements of This Proposed AD

    This product has been approved by the aviation authority of Canada, 
and is approved for operation in the United States. Pursuant to our 
bilateral agreement with this State of Design Authority, we have been 
notified of the unsafe condition described in the MCAI and service 
information. We are proposing this AD because we evaluated all 
pertinent information and determined an unsafe condition exists and is 
likely to exist or develop on other products of the same type design.

Differences Between This AD and the MCAI or Service Information

    We have reviewed the MCAI and related service information and, in 
general, agree with their substance. But we might have found it 
necessary to use different words from those in the MCAI to ensure the 
AD is clear for U.S. operators and is enforceable. In making these 
changes, we do not intend to differ substantively from the information 
provided in the MCAI and related service information.
    We might also have proposed different actions in this AD from those 
in the MCAI in order to follow FAA policies. Any such differences are 
highlighted in the ``Differences Between the FAA AD and the MCAI'' 
section in the proposed AD.

Costs of Compliance

    We estimate that this proposed AD would affect about 86 products of 
U.S. registry. Also, we estimate that it would take 2 work-hours per 
product to comply with the basic requirements of this proposed AD. The 
average labor rate is $80 per work-hour. A

[[Page 64544]]

replacement yoke would cost about $21,218, assuming the part is no 
longer under warranty. However, because the service information lists 
this part as covered under warranty, we have assumed that there will be 
no charge for this part. Therefore, as we do not control warranty 
coverage for affected parties, some parties may incur costs higher than 
estimated here. Based on these figures, we estimate the cost of the 
proposed AD on U.S. operators to be $13,760, or $160 per helicopter.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more detail the scope of the Agency's 
authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979); and
    3. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.
    We prepared an economic evaluation of the estimated costs to comply 
with this proposed AD and placed it in the AD docket.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

    1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

    2. The FAA amends Sec.  39.13 by adding the following new AD:

Bell Helicopter Textron Canada: Docket No. FAA-2007-0178; 
Directorate Identifier 2007-SW-20-AD.

Comments Due Date

    (a) We must receive comments by December 17, 2007.

Other Affected ADs

    (b) None.

Applicability

    (c) This AD applies to Bell Helicopter Textron Canada (BHTC) 
Model 222, serial numbers (S/N) 47006 through 47089; Model 222B, S/N 
47131 through 47156, and Model 222U, all serial numbers, 
helicopters, certificated in any category.

Reason

    (d) The mandatory continuing airworthiness information (MCAI) 
states:
    It has been determined that the existing rigging procedures for 
the tail rotor pitch change mechanism have to be changed due to 
possibility of parts interference.
    This ``possibility of parts interference'' occurs because the 
cumulative effect of the tolerances on the various parts may result 
in the total assemblage outboard of the counterweight bellcrank 
being out of tolerance and the tail rotor yoke may contact nut, P/N 
222-012-731-001, before contacting the flapping stop. Further, the 
manufacturer has indicated that the tail rotor counterweight 
bellcranks may be misaligned resulting in higher tail rotor pedal 
forces and higher pilot workload after failure of the No. 1 
hydraulic system. Both the parts interference and the higher pedal 
forces constitute unsafe conditions.

Actions and Compliance

    (e) Within the next 150 hours time-in-service (TIS) or at the 
next annual inspection, whichever occurs first, unless already done, 
do the following actions.
    (1) Adjust the rigging of the tail rotor pitch change mechanism 
in accordance with the Accomplishment Instructions, Paragraphs 1 and 
2, of the applicable Bell Helicopter Textron Alert Service Bulletin 
(ASB) listed in the following Table 1:

                                 Table 1
------------------------------------------------------------------------
           Helicopter model                   Applicable ASB & date
------------------------------------------------------------------------
222 and 222B..........................  222-07-104 dated January 9,
                                         2007.
222U..................................  222U-07-75 dated January 9,
                                         2007.
------------------------------------------------------------------------

    (2) If either at full left pedal position or full right pedal 
position a gap exists between the tail rotor yoke and the flapping 
stop, replace the tail rotor yoke with an airworthy tail rotor yoke.
    (3) If no gap exists between the tail rotor yoke and the 
flapping stop at either full right or full left pedal position, 
measure the gap between the tail rotor yoke and nut, P/N 222-012-
731-001, adjust the tail rotor pitch change mechanism, and adjust 
the tail rotor pedal forces in accordance with the Accomplishment 
Instruction, Paragraphs 4 through 6, of the ASB listed in Table 1 of 
the AD.

Differences Between the FAA AD and the MCAI

    (f) This AD requires compliance within the next 150 hours TIS or 
at the next annual inspection, whichever occurs first, instead of 
``at the next 150 hour or annual inspection but no later than 31 
December 2007.

Subject

    (g) Air Transport Association of America (ATA) Code JASC 6720: 
Tail Rotor Control System, Tail Rotor Pitch Change.

Other Information

    (h) The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
Safety Management Group, FAA, has the authority to approve AMOCs for 
this AD, if requested using the procedures found in 14 CFR 39.19. 
Send information to ATTN: Tyrone Millard, Aerospace Engineer; FAA, 
Rotorcraft Directorate, Rotorcraft Standards Staff, Fort Worth, 
Texas 76193-0111, telephone (817) 222-5439, fax (817) 222-5961.
    (2) Airworthy Product: Use only FAA-approved corrective actions. 
Corrective actions are considered FAA-approved if they are approved 
by the State of Design Authority (or their delegated agent) if the 
State of Design has an appropriate bilateral agreement with the 
United States. You are required to assure the product is airworthy 
before it is returned to service.
    (3) Reporting Requirements: For any reporting requirement in 
this AD, under the provisions of the Paperwork Reduction Act, the 
Office of Management and Budget (OMB) has approved the information 
collection requirements and has assigned OMB Control Number 2120-
0056.

Related Information

    (i) MCAI Transport Canada Airworthiness Directive CF-2007-07, 
dated April 11, 2007, and Bell Helicopter Textron ASB Nos. 222-07-
104 and 222U-07-75, both dated January 9, 2007, contain related 
information.


[[Page 64545]]


    Issued in Fort Worth, Texas, on November 5, 2007.
David A. Downey,
Manager, Rotorcraft Directorate, Aircraft Certification Service.
[FR Doc. E7-22441 Filed 11-15-07; 8:45 am]

BILLING CODE 4910-13-P
