
[Federal Register: March 26, 2008 (Volume 73, Number 59)]
[Rules and Regulations]               
[Page 15866-15868]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr26mr08-3]                         

-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2005-21242; Directorate Identifier 2005-NE-09-AD; 
Amendment 39-15442; AD 2008-07-01]
RIN 2120-AA64

 
Airworthiness Directives; Turbomeca Arriel 1B, 1D, 1D1, and 1S1 
Turboshaft Engines

AGENCY: Federal Aviation Administration (FAA), Department of 
Transportation (DOT).

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: The FAA is superseding an existing airworthiness directive 
(AD) for certain Turbomeca Arriel 1B, 1D, 1D1, and 1S1 turboshaft 
engines. That AD currently requires initial and repetitive position 
checks of the gas generator 2nd stage turbine blades on all Turbomeca 
Arriel 1B, 1D, 1D1, and 1S1 turboshaft engines. That AD also currently 
requires initial and repetitive replacements of 2nd stage turbines on 
1B, 1D, and 1D1 engines only. This AD requires adding a 3,000 hour life 
limit to Arriel 1B 2nd stage turbine blades. This AD results from 
reports of failures of second stage turbine blades. We are issuing this 
AD to prevent failures of the 2nd stage turbine blades, which could 
result in uncommanded in-flight engine shutdown, and subsequent forced 
autorotation landing or accident.

DATES: This AD becomes effective April 30, 2008. The Director of the 
Federal Register approved the incorporation by reference of certain 
publications listed in the regulations as of April 30, 2008. The 
Director of the Federal Register previously approved the incorporation 
by reference of Turbomeca Mandatory Alert Service Bulletins A292 72 
0809, Update 1, dated October 4, 2005; and A292 72 0810, dated March 
24, 2004; as of February 28, 2006 (71 FR 3754, January 24, 2006).

ADDRESSES: You can get the service information identified in this AD 
from Turbomeca, 40220 Tarnos, France; telephone (33) 05 59 74 40 00, 
fax (33) 05 59 74 45 15.
    The Docket Operations office is located at Docket Management 
Facility, U.S. Department of Transportation, 1200 New Jersey Avenue, 
SE., West Building Ground Floor, Room W12-140, Washington, DC 20590-
0001.

FOR FURTHER INFORMATION CONTACT: James Lawrence, Aerospace Engineer, 
Engine Certification Office, FAA, Engine and Propeller Directorate, 12 
New England Executive Park, Burlington, MA 01803; e-mail: 
james.lawrence@faa.gov; telephone (781) 238-7176, fax (781) 238-7199.

SUPPLEMENTARY INFORMATION: The FAA proposed to amend 14 CFR part 39 by 
superseding AD 2006-02-08R1, Amendment 39-14721 (71 FR 46390, August 
14, 2006), with a proposed AD. The proposed AD applies to certain 
Turbomeca Arriel 1B, 1D, 1D1, and 1S1 turboshaft engines. We published 
the proposed AD in the Federal Register on March 9, 2007 (72 FR 10622). 
That action proposed to require:
     Initial and repetitive position checks of the 2nd stage 
turbine blades on Turbomeca Arriel 1B, 1D, 1D1, and 1S1 turboshaft 
engines.
     Replacement of 2nd stage turbines on 1B and 1D1 engines 
only.
     Initially replacing 2nd stage turbines in Arriel 1B, 1D, 
and 1D1 turboshaft engines.

Examining the AD Docket

    You may examine the AD docket on the Internet at http://
www.regulations.gov; or in person at the Docket Operations office 
between 9 a.m. and 5 p.m., Monday through Friday, except Federal 
holidays. The AD docket contains this AD, the regulatory evaluation, 
any comments received, and other information. The street address for 
the Docket Operations office (telephone (800) 647-5527) is provided in 
the ADDRESSES section. Comments will be available in the AD docket 
shortly after receipt.

Comments

    We provided the public the opportunity to participate in the 
development of this AD. We received no comments on the proposal or on 
the determination of the cost to the public.

Addition of an Optional Terminating Action

    We have added to the AD, an option to terminate the repetitive 
position check requirements by installing a new turbine, part number 
(P/N) 0 292 25 039 0.

Correction of a Typographical Error in the Costs of Compliance

    We corrected the number of turbine replacements in the Costs of 
Compliance from 587 to 571, and changed the total cost from $3,905,240 
to $3,769,760.

Conclusion

    We have carefully reviewed the available data and determined that 
air safety and the public interest require adopting the AD as proposed.

[[Page 15867]]

Costs of Compliance

    We estimate that this AD will affect 721 engines installed on 
helicopters of U.S. registry. We also estimate that it will take about 
2 work-hours per engine to inspect all 721 engines and 40 work-hours 
per engine to replace about 571 2nd stage turbines on 1B and 1D1 
engines, and that the average labor rate is $80 per work-hour. Required 
parts would cost about $3,200 per engine. Based on these figures, we 
estimate the total cost of the AD to U.S. operators to be $3,769,760.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, Section 106, describes the 
authority of the FAA Administrator. Subtitle VII, Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701, ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We have determined that this AD will not have federalism 
implications under Executive Order 13132. This AD will not have a 
substantial direct effect on the States, on the relationship between 
the national government and the States, or on the distribution of power 
and responsibilities among the various levels of government.
    For the reasons discussed above, I certify that this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866;
    (2) Is not a ``significant rule'' under DOT Regulatory Policies and 
Procedures (44 FR 11034, February 26, 1979); and
    (3) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.
    We prepared a summary of the costs to comply with this AD and 
placed it in the AD Docket. You may get a copy of this summary at the 
address listed under ADDRESSES.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

0
Accordingly, under the authority delegated to me by the Administrator, 
the Federal Aviation Administration amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by removing Amendment 39-14721 (71 FR 
46390, August 14, 2006) and by adding a new airworthiness directive, 
Amendment 39-15442, to read as follows:

2008-07-01 Turbomeca: Amendment 39-15442. Docket No. FAA-2005-21242; 
Directorate Identifier 2005-NE-09-AD.

Effective Date

    (a) This airworthiness directive (AD) becomes effective April 
30, 2008.

Affected ADs

    (b) This AD supersedes AD 2006-02-08R1, Amendment 39-14721 (71 
FR 46390, August 14, 2006).

Applicability

    (c) This AD applies to Turbomeca Arriel 1B engines fitted with 
2nd stage turbine modification TU 148, and Arriel 1D, 1D1, and 1S1 
engines that do not incorporate TU 347. Arriel 1B engines are 
installed on, but not limited to, Eurocopter France AS-350B and AS-
350A ``Ecureuil'' helicopters. Arriel 1D engines are installed on, 
but not limited to, Eurocopter France AS-350B1 ``Ecureuil'' 
helicopters. Arriel 1D1 engines are installed on, but not limited 
to, Eurocopter France AS-350B2 ``Ecureuil'' helicopters. Arriel 1S1 
engines are installed on, but not limited to, Sikorsky Aircraft S-
76A and S-76C helicopters.

Unsafe Condition

    (d) This AD results from reports of failures of second stage 
blades. We are issuing this AD to prevent failures of the 2nd stage 
turbine blades, which could result in uncommanded in-flight engine 
shutdown, and subsequent forced autorotation landing or accident.

Compliance

    (e) You are responsible for having the actions required by this 
AD performed within the compliance times specified unless the 
actions have already been done.

Initial Relative Position Check of 2nd Stage Turbine Blades

    (f) Do an initial relative position check of the 2nd stage 
turbine blades using the Turbomeca mandatory alert service bulletins 
(ASBs) specified in the following Table 1. Do the check before 
reaching any of the intervals specified in Table 1 or within 50 
hours time-in-service after the effective date of this AD, whichever 
occurs later.

          Table 1.--Initial and Repetitive Relative Position Check Intervals of 2nd Stage Turbine Blade
----------------------------------------------------------------------------------------------------------------
                                   Initial relative position                             Mandatory Alert Service
      Turbomeca engine model             check interval          Repetitive interval            Bulletin
----------------------------------------------------------------------------------------------------------------
Arriel 1B (modified per TU 148)..  Within 1,200 hours time-   Within 200 hours time-in- A292 72 0807, Update 1,
                                    since-new (TSN) or time-   service-since-last-       dated October 26, 2006.
                                    since-overhaul (TSO) or    relative-position-check
                                    3,500 cycles-since-new     (TSLRPC).
                                    (CSN) or cycles-since-
                                    overhaul (CSO),
                                    whichever occurs earlier.
Arriel 1D1 and Arriel 1D.........  Within 1,200 hours TSN or  Within 150 hours TSLRPC.  A292 72 0809, Update No.
                                    TSO or 3,500 CSN or CSO,                             1, dated October 4,
                                    whichever occurs earlier.                            2005.
Arriel 1S1.......................  Within 1,200 hours TSN or  Within 150 hours TSLRPC.  A292 72 0810, dated
                                    TSO or 3,500 CSN or CSO,                             March 24, 2004.
                                    whichever occurs earlier.
----------------------------------------------------------------------------------------------------------------


[[Page 15868]]

Repetitive Relative Position Check of 2nd Stage Turbine Blades

    (g) Recheck the relative position of 2nd stage turbine blades at 
the TSLRPC intervals specified in Table 1 of this AD, using the 
mandatory ASBs indicated.

Credit for Previous Relative Position Checks

    (h) Relative position checks of 2nd stage turbine blades done 
using Turbomeca Service Bulletin A292 72 0263, Update 1, 2, 3, or 4, 
or A292 72 0807, dated March 24, 2004, comply with the initial 
requirements of paragraph (f) of this AD.

Initial Replacement of 2nd Stage Turbines on Arriel 1B, 1D, and 1D1 
Engines

    (i) Initially replace the 2nd stage turbine with a new or 
overhauled 2nd stage turbine as follows:
    (1) Before accumulating 1,500 hours TSN or TSO on the module for 
Arriel 1D and 1D1 engines.
    (2) Before accumulating 2,200 hours TSN or TSO on the module or 
3,000 total hours TSN on the 2nd stage turbine blades, whichever 
occurs first, for Arriel 1B engines.

Repetitive Replacements of 2nd Stage Turbines on Arriel 1B, 1D, and 1D1 
Engines

    (j) Thereafter, replace the 2nd stage turbine with a new or 
overhauled 2nd stage turbine within every 1,500 hours TSN or TSO on 
the module for Arriel 1D and 1D1 engines, and within every 2,200 
hours TSN or TSO on the module or 3,000 total hours TSN on the 2nd 
stage turbine blades, for Arriel 1B engines.

Criteria for Overhauled 2nd Stage Turbines

    (k) Do the following to overhauled 2nd stage turbines, 
referenced in paragraphs (i) and (j) of this AD:
    (1) You must install new blades in the 2nd stage turbines of 
overhauled Arriel 1D and 1D1 engines.
    (2) You may install either overhauled blades with fewer than 
3,000 total hours TSN or new blades in the 2nd stage turbines of 
overhauled Arriel 1B engines.

Relative Position Check Continuing Compliance Requirements

    (l) All 2nd stage turbines, including those that are new or 
overhauled, must continue to comply with the actions specified in 
paragraphs (f), (g), and (j) of this AD.

Optional Terminating Action

    (m) Installing a new turbine, P/N 0 292 25 039 0, reference TU 
347, terminates the requirements to perform the repetitive actions 
specified in paragraphs (g) and (j) of this AD.

Alternative Methods of Compliance

    (n) The Manager, Engine Certification Office, has the authority 
to approve alternative methods of compliance for this AD if 
requested using the procedures found in 14 CFR 39.19.

Related Information

    (o) The EASA airworthiness directive 2007-0018R1, dated August 
14, 2007, also addresses the subject of this AD.
    (p) Contact James Lawrence, Aerospace Engineer, Engine 
Certification Office, FAA, Engine and Propeller Directorate, 12 New 
England Executive Park, Burlington, MA 01803; e-mail: 
james.lawrence@faa.gov; telephone (781) 238-7176, fax (781) 238-
7199, for more information about this AD.

Material Incorporated by Reference

    (q) You must use the service information specified in Table 2 of 
this AD to perform the actions required by this AD.
    (1) The Director of the Federal Register approved the 
incorporation by reference of Turbomeca Mandatory Alert Service 
Bulletin A292 72 0807, Update 1, dated October 26, 2006, in 
accordance with 5 U.S.C. 552(a) and 1 CFR part 51.
    (2) The Director of the Federal Register previously approved the 
incorporation by reference of Turbomeca Mandatory Alert Service 
Bulletins A292 72 0809, Update 1, dated October 4, 2005; and A292 72 
0810, dated March 24, 2004; as of February 28, 2006 (71 FR 3754, 
January 24, 2006).
    (3) Contact Turbomeca, 40220 Tarnos, France; telephone (33) 05 
59 74 40 00, fax (33) 05 59 74 45 15 for a copy of this service 
information. You may review copies at the FAA, New England Region, 
12 New England Executive Park, Burlington, MA; or at the National 
Archives and Records Administration (NARA). For information on the 
availability of this material at NARA, call 202-741-6030, or go to: 
http://www.archives.gov/federal-register/cfr/ibr-locations.html.

                                      Table 2.--Incorporation by Reference
----------------------------------------------------------------------------------------------------------------
 Turbomeca Mandatory Alert Service
            Bulletin No.                      Page                Update No.                    Date
----------------------------------------------------------------------------------------------------------------
A292 72 0807, Total Pages: 18......  ALL..................  1....................  October 26, 2006.
A292 72 0809, Total Pages: 18......  ALL..................  1....................  October 4, 2005.
A292 72 0810, Total Pages: 14......  ALL..................  Original.............  March 24, 2004.
----------------------------------------------------------------------------------------------------------------


    Issued in Burlington, Massachusetts, on March 17, 2008.
Ann C. Mollica,
Acting Manager, Engine and Propeller Directorate, Aircraft 
Certification Service.
 [FR Doc. E8-5819 Filed 3-25-08; 8:45 am]

BILLING CODE 4910-13-P
