
[Federal Register: October 28, 2008 (Volume 73, Number 209)]
[Rules and Regulations]               
[Page 64067-64097]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr28oc08-13]                         


[[Page 64067]]

-----------------------------------------------------------------------

Part III





Environmental Protection Agency





-----------------------------------------------------------------------



40 CFR Part 63



NESHAP: National Emission Standards for Hazardous Air Pollutants: 
Standards for Hazardous Waste Combustors: Reconsideration; Final Rule


[[Page 64068]]


-----------------------------------------------------------------------

ENVIRONMENTAL PROTECTION AGENCY

40 CFR Part 63

[EPA-HQ-OAR-2004-0022; FRL-8733-1]
RIN 2050-AG35

 
NESHAP: National Emission Standards for Hazardous Air Pollutants: 
Standards for Hazardous Waste Combustors: Reconsideration

AGENCY: Environmental Protection Agency (EPA).

ACTION: Final rule; reconsideration.

-----------------------------------------------------------------------

SUMMARY: On October 12, 2005, EPA promulgated national emission 
standards for hazardous air pollutants (NESHAP) for new and existing 
sources at hazardous waste combustion facilities (the final rule). 
Subsequently, the Administrator received four petitions for 
reconsideration of the final rule. On March 23, 2006 and September 6, 
2006, EPA granted reconsideration with respect to eight issues raised 
by the petitions. After evaluating public comments submitted in 
response to these reconsideration notices, we are taking final action 
regarding the eight issues raised in the petitions for reconsideration. 
EPA also re-opened the rule to consider comments relating to a post-
promulgation decision of the United States Court of Appeals for the 
District of Columbia Circuit, and is responding in this proceeding to 
the comments received on that notice, published on September 27, 2007. 
As a result of this reconsideration process, we are revising the new 
source standard for particulate matter for cement kilns and for 
incinerators that burn hazardous waste. We are also making amendments 
to the particulate matter detection system provisions and revisions to 
the health-based compliance alternative for total chlorine of the final 
rule. Finally, we are also issuing several corrections and 
clarifications to the final rule.

DATES: The final rule is effective on October 28, 2008.

ADDRESSES: EPA has established a docket for this action under Docket ID 
No. EPA-HQ-OAR-2004-0022. All documents in the docket are listed on the 
http://www.regulations.gov Web site. Although listed in the index, some 
information is not publicly available, e.g., CBI or other information 
the disclosure of which is restricted by statute. Certain other 
material, such as copyrighted material, is not placed on the Internet 
and will be publicly available only in hard copy form. Publicly 
available docket materials are available either electronically through 
http://www.regulations.gov or in hard copy at the HQ EPA Docket Center, 
Docket ID No. EPA-HQ-OAR-2004-0022, EPA West Building, Room 3334, 1301 
Constitution Ave., NW., Washington, DC 20004. This Docket Facility is 
open from 8:30 a.m. to 4:30 p.m., Monday through Friday, excluding 
legal holidays. The HQ EPA Docket Center telephone number is (202) 566-
1742. The Public Reading Room is open from 8:30 a.m. to 4:30 p.m., 
Monday through Friday, excluding legal holidays. The telephone number 
for the Public Reading Room is (202) 566-1744. A reasonable fee may be 
charged for copying docket materials.

FOR FURTHER INFORMATION CONTACT: For more information on this final 
rule, contact Frank Behan at (703) 308-8476, or behan.frank@epa.gov, 
Office of Solid Waste (MC: 5302P), U.S. Environmental Protection 
Agency, 1200 Pennsylvania Ave., NW., Washington, DC 20460.

SUPPLEMENTARY INFORMATION:
    Outline. The SUPPLEMENTARY INFORMATION in this preamble is 
organized as follows:

I. General Information
    A. Does this action apply to me?
    B. Where can I get a copy of this document?
    C. Judicial Review
II. Background
    A. What Is the Source of Authority for the Reconsideration 
Action?
    B. What Is the Background on the NESHAP for Hazardous Waste 
Combustors?
III. Final Action on Issues for Which EPA Granted Reconsideration
    A. Subcategorization of Liquid Fuel Boilers by Heating Value
    B. Correcting Total Chlorine (TCl) Data to 20 ppmv
    C. Use of PS-11 and Procedure 2 as Guidance for Extrapolating 
the Alarm Set-Point of a Particulate Matter Detection System (PMDS)
    D. Tie-Breaking Procedure for New Source Standards
    E. New Source Particulate Matter Standard for New Cement Kilns
    F. Beyond-the-Floor Analyses To Consider Multiple HAP That Are 
Similarly Controlled
    G. Dioxin/Furan Standard for Incinerators With Dry Air Pollution 
Control Devices
    H. Provisions of the Health-Based Compliance Alternative
IV. Response to Comments to the September 27, 2007 Notice
    A. Standards for Particulate Matter
    B. Standards for Semivolatile Metals and Low Volatile Metals
    C. Standards for Total Chlorine
    D. Standards for Dioxins/Furans
    E. Standards for Non-Dioxin/Furan Organic HAP
    F. Standards for Mercury
    G. Normalization
V. What Other Rule Provisions Are Being Amended or Clarified?
    A. What corrections are we making?
    B. Clarification of the PM Standard for Cement Kilns
VI. Summary of Environmental, Energy, and Economic Impacts
    A. What facilities are affected by the final amendments?
    B. What are the air quality impacts?
    C. What are the water quality, solid waste, energy, cost and 
economic impacts?
VII. Statutory and Executive Order Reviews
    A. Executive Order 12866: Regulatory Planning and Review
    B. Paperwork Reduction Act
    C. Regulatory Flexibility Act
    D. Unfunded Mandates Reform Act
    E. Executive Order 13132: Federalism
    F. Executive Order 13175: Consultation and Coordination With 
Indian Tribal Governments
    G. Executive Order 13045: Protection of Children From 
Environmental Health Risks and Safety Risks
    H. Executive Order 13211: Actions Concerning Regulations That 
Significantly Affect Energy Supply, Distribution, or Use
    I. National Technology Transfer and Advancement Act
    J. Executive Order 12898: Federal Actions To Address 
Environmental Justice in Minority Populations and Low-Income 
Populations
    K. Congressional Review

I. General Information

A. Does this action apply to me?

    The regulated categories and entities affected by this final action 
include:

------------------------------------------------------------------------
                                    NAICS code    Potentially affected
             Category                   a               entities
------------------------------------------------------------------------
Petroleum and coal products                324  Any entity that combusts
 manufacturing.                                  hazardous waste as
                                                 defined in the final
                                                 rule.
Chemical manufacturing...........          325
Cement and concrete product               3273
 manufacturing.
Other nonmetallic mineral product         3279
 manufacturing.
Waste treatment and disposal.....         5622

[[Page 64069]]


Remediation and other waste               5629
 management services.
------------------------------------------------------------------------
a North American Industry Classification System.

    This table is not intended to be exhaustive, but rather provides a 
guide for readers regarding entities likely to be impacted by this 
action. To determine whether your facility is affected by this action, 
you should examine the applicability criteria in 40 CFR 63.1200, ``Who 
is subject to these regulations?''. If you have any questions regarding 
the applicability of this action to a particular entity, consult either 
the air permit authority for the entity or your EPA regional 
representative as listed in Sec.  63.13 of the General Provisions to 
part 63 (40 CFR part 63, subpart A).

B. Where can I get a copy of this document?

    In addition to being available in the docket, an electronic copy of 
this final action will also be available on the Worldwide Web (WWW) 
through the Technology Transfer Network (TTN). Following signature, a 
copy of the final action will be posted on the TTN's policy and 
guidance page for newly proposed or promulgated rules at the following 
address: http://www.epa.gov/ttn/oarpg/. The TTN provides information 
and technology exchange in various areas of air pollution control. This 
action is also available at the following address: http://www.epa.gov/
hwcmact.

C. Judicial Review

    Under section 307(b)(1) of the Clean Air Act (CAA), judicial review 
of this final rule is available only by filing a petition for review in 
the U.S. Court of Appeals for the District of Columbia Circuit by 
December 29, 2008. Under section 307(d)(7)(B) of the CAA, only an 
objection to these final rules that was raised with reasonable 
specificity during the period for public comment can be raised during 
judicial review. This section also provides a mechanism for EPA to 
convene a proceeding for reconsideration, ``[i]f the person raising an 
objection can demonstrate to EPA that it was impracticable to raise 
such objection within [the period for public comment] or if the grounds 
for such objection arose after the period for public comment (but 
within the time specified for judicial review) and if such objection is 
of central relevance to the outcome of this rule.'' Any person seeking 
to make such a demonstration to us should submit a Petition for 
Reconsideration to the Office of the Administrator, Environmental 
Protection Agency, Room 3000, Ariel Rios Building, 1200 Pennsylvania 
Ave., NW., Washington, DC 20004, with a copy to the person listed in 
the preceding FOR FURTHER INFORMATION CONTACT section, and the 
Associate General Counsel for the Air and Radiation Law Office, Office 
of General Counsel (Mail Code 2344A), Environmental Protection Agency, 
1200 Pennsylvania Ave., NW., Washington, DC 20004. Moreover, under 
section 307(b)(2) of the CAA, the requirements established by these 
final rules may not be challenged separately in any civil or criminal 
proceedings brought by EPA to enforce these requirements.

II. Background

A. What Is the Source of Authority for the Reconsideration Action?

    EPA is reconsidering several aspects of its final rule for 
hazardous waste combustors under sections 112(d) and 307(d)(7)(B) of 
the Clean Air Act (CAA) as amended (42 U.S.C. 7412(d) and 
7607(d)(7)(B)). This action is also subject to section 307(d) of the 
CAA (42 U.S.C. 7607(d)).

B. What Is the Background on the NESHAP for Hazardous Waste Combustors?

    Section 112 of the CAA requires that we establish NESHAP for the 
control of hazardous air pollutants (HAP) from both new and existing 
major sources. Major sources of HAP are those stationary sources or 
groups of stationary sources that are located within a contiguous area 
under common control that emit or have the potential to emit 
considering controls, in the aggregate, 10 tons per year (tpy) or more 
of any one HAP or 25 tpy or more of any combination of HAP. For major 
sources, the CAA requires the NESHAP to reflect the maximum degree of 
reduction in emissions of HAP that is achievable.\1\ This level of 
control is commonly referred to as MACT (for Maximum Achievable Control 
Technology). See CAA section 112(d)(2).
---------------------------------------------------------------------------

    \1\ Section 112(d)(4) gives the Administrator the authority to 
establish health-based emission standards in lieu of the MACT 
standards for HAP for which a health threshold has been established. 
In the final rule promulgated on October 12, 2005, EPA established 
health-based compliance alternatives for total chlorine as an 
alternative to the MACT technology-based emission standards, which 
alternative standards are applicable to all hazardous waste 
combustors, with the exception of hydrochloric acid production 
furnaces. 70 FR at 59478-486.
---------------------------------------------------------------------------

    The minimum control level for major sources is defined under 
section 112(d)(3) of the CAA, and is referred to, informally, as ``the 
MACT floor.'' The MACT floor ensures that the standards are set at a 
level that assures that all major sources perform at the level of 
control at least as stringent as that already achieved by the best-
performing sources in each source category or subcategory. 
Specifically, for new major sources, the MACT floor cannot be less 
stringent than the emission control that is achieved in practice by the 
best-controlled similar source. The MACT standards for existing major 
sources can be less stringent than standards for new sources, but they 
cannot be less stringent than the average emission limitation achieved 
by the best-performing 12 percent of existing sources in the category 
or subcategory for which the Administrator has emissions information 
(where there are 30 or more sources in a category or subcategory; 
floors for existing sources in categories or subcategories with fewer 
than 30 sources are to be based on the average emission limitation 
achieved by the best performing five sources).
    EPA also must consider more stringent ``beyond-the-floor'' control 
options. When considering beyond-the-floor options, EPA must consider 
not only the maximum degree of reduction in emissions of HAP, but must 
take into account costs, energy, and non-air quality health 
environmental impacts. See CAA section 112(d)(2).
    We proposed NESHAP for hazardous waste combustors on April 20, 2004 
(69 FR 21198), and we published the final rule on October 12, 2005 (70 
FR 59402). The hazardous waste combustor NESHAP is codified in subpart 
EEE of 40 CFR part 63. Following promulgation of the hazardous waste 
combustor final rule, the Administrator received four petitions for 
reconsideration, pursuant to section 307(d)(7)(B) of the CAA, from Ash 
Grove Cement Company, the Cement Kiln Recycling Coalition (CKRC), the 
Coalition for Responsible Waste Incineration (CRWI), and the Sierra 
Club.\2\ Under this section of the

[[Page 64070]]

CAA, the Administrator must initiate reconsideration proceedings with 
respect to provisions that are of central relevance to the rule at 
issue if the petitioner shows that it was impracticable to raise an 
objection to a rule within the public comment period or that the 
grounds for the objection arose after the public comment period but 
within the period for filing petitions for judicial review.
---------------------------------------------------------------------------

    \2\ These petitions are included in the docket for this rule. 
See items EPA-HQ-OAR-2004-0022-0516 thru 0519. EPA also received 
petitions from Ash Grove Cement Company and the CKRC, Continental 
Cement Company, and Giant Cement Holding, Inc. requesting that we 
stay the effective date of the particulate matter standard for new 
cement kilns. See items EPA-HQ-OAR-2004-0022-0521 and 0523.
---------------------------------------------------------------------------

    Of the twenty or so issues raised in the four petitions for 
reconsideration, we decided to grant immediate reconsideration of one 
of the issues included in the petitions of Ash Grove Cement Company and 
CKRC. On March 23, 2006, EPA published a proposed rule granting 
reconsideration of the particulate matter standard for new cement 
kilns. 71 FR 14665. Also on March 23, 2006, EPA granted a three-month 
administrative stay while the particulate matter standard was under 
reconsideration. 71 FR 14655. The administrative stay was issued 
pursuant to section 307(d)(7)(B) of the CAA and was in effect from 
March 23, 2006 to June 23, 2006. Approximately a dozen public comment 
letters were submitted in response to the March 2006 proposed rule, 
including a request to extend the comment period by two weeks that EPA 
granted in a subsequent notice on April 13, 2006. 71 FR 19155. On 
October 25, 2006, EPA issued a final rule amending the effective date 
of the particulate matter standard for new cement kilns. 71 FR 62388. 
That amendment suspended the obligation of new cement kilns to comply 
with the particulate matter standard set forth in Sec.  
63.1220(b)(7)(i) until we take final action on the March 2006 proposal 
to revise the standard. Today's rule announces our final action 
regarding Ash Grove Cement Company and CKRC's petitions for 
reconsideration of the particulate matter standard for new cement kilns 
that was first proposed on March 23, 2006.
    On August 22, 2006, EPA issued letters to the Ash Grove Cement 
Company, the CKRC, and the Sierra Club explaining our rationale to deny 
reconsideration on several issues.\3\ On September 6, 2006, we 
announced our reconsideration of and requested public comment on seven 
issues raised in the petitions of the Ash Grove Cement Company, the 
CKRC, and the Sierra Club. 71 FR 52624. In addition to requesting 
comment on the reconsideration issues, we also sought comment on 
several other proposed amendments to various compliance and monitoring 
provisions in the hazardous waste combustor NESHAP. Eleven commenters 
submitted responses to this reconsideration notice. In addition to 
addressing the PM standard for new cement kilns, today's rule announces 
our final decision regarding the seven petition for reconsideration 
issues and the other compliance and monitoring amendments included in 
the September 2006 proposed rule.
---------------------------------------------------------------------------

    \3\ A copy of each letter is included in the docket to this 
rulemaking. See docket items EPA-HQ-OAR-2004-0022-0558 through 0560. 
A summary of the issues for which we denied reconsideration can also 
be found in the September 6, 2006 proposed rule. 71 FR at 52627.
---------------------------------------------------------------------------

    On September 27, 2007, EPA issued a Federal Register notice 
discussing each of the standards in the rule in light of the DC 
Circuit's decision in Sierra Club v. EPA, 479 F. 3d 875 (2007) (``Brick 
MACT''). The specific focus of this analysis was whether the MACT 
floors for each standard were consistent with the requirements of 
section 112(d)(2) and (d)(3) of the Act. EPA also sought comment on 
amending the record to make clear that it was no longer relying on 
certain rationales which appeared inconsistent with the Brick MACT 
opinion. EPA solicited and received comment on this analysis and is 
responding to those comments in this notice.

III. Final Action on Issues for Which EPA Granted Reconsideration

    EPA granted reconsideration of eight issues raised in the petitions 
of the Ash Grove Cement Company, the Cement Kiln Recycling Coalition, 
the Coalition for Responsible Waste Incineration, and the Sierra Club. 
Accordingly, we requested comment on the eight issues in two notices 
published on March 23, 2006 (71 FR 14665) and September 6, 2006 (71 FR 
52624). We discuss below our final action regarding the eight issues 
raised in the four petitions for reconsideration and include our 
response to the major comments received on these issues.

A. Subcategorization of Liquid Fuel Boilers by Heating Value

    In the October 12, 2005 final rule, we divided the liquid fuel 
boiler subcategory into two separate boiler subcategories based on the 
heating value of the hazardous waste they burn for purposes of 
establishing emission standards for metals and total chlorine (TCl): 
Those that burn waste with a heating value below 10,000 Btu/lb, and 
those that burn hazardous waste with a heating value of 10,000 Btu/lb 
or greater. See 70 FR at 59422. Sources would shift from one 
subcategory to the other depending on the heating value of the 
hazardous waste burned at the time. Id. at 59476.
    Sierra Club petitioned for reconsideration stating that EPA 
developed this subcategorization approach after the period for public 
comment and, thus, did not provide notice and opportunity for public 
comment.\4\ We subsequently granted reconsideration of this provision. 
See 71 FR at 52627-28 (September 6, 2006). Although we granted 
reconsideration, we did not propose to change the approach.
---------------------------------------------------------------------------

    \4\ See letter from James Pew to Stephen Johnson, dated December 
12, 2005, Section II, docket item EPA-HQ-OAR-2004-0022-0517.
---------------------------------------------------------------------------

    This issue has now become moot because EPA has determined that the 
standard for the high heating value subcategory requires revision 
because it only applied to HAP in hazardous waste, not to all HAP input 
to the boiler (for example, HAP that may be present in fossil fuels or 
other non-waste inputs), which is contrary to the DC Circuit's 
decisions in Brick MACT, 479 F. 3d at 882-83. (MACT standards must 
apply to all HAP regardless of source of input). Moreover, once the 
high heating value subcategory is eliminated, there is no basis for a 
low heating value subcategory since the whole basis for differentiation 
no longer exists. Accordingly, EPA now agrees with the petitioner that 
the subcategorization scheme it adopted for liquid fuel boilers is not 
appropriate, and EPA intends to amend these standards. See also 
preamble sections IV.B and IV.F below (responding to comments on EPA's 
September 27, 2007 notice).

B. Correcting Total Chlorine (TCl) Data to 20 ppmv

    In the October 12, 2005 final rule, we corrected all the total 
chlorine (TCl) measurements in the data base that were below 20 ppmv to 
account for potential systemic negative biases in the Method 0050 data. 
See 70 FR at 59427-29.\5\ Sierra Club petitioned for reconsideration 
stating that EPA corrected the TCl measurements in response to comments 
on the proposed rule--after the period for public comment--and used the 
corrected data to revise the TCl emission standards.\6\
---------------------------------------------------------------------------

    \5\ See also USEPA, ``Technical Support Document for HWC MACT 
Standards, Volume III: Selection of MACT Standards,'' Section 5.5, 
September 2005.
    \6\ See letter from James Pew to Stephen Johnson, dated December 
12, 2005, Section IV, docket item EPA-HQ-OAR-2004-0022-0517.

---------------------------------------------------------------------------

[[Page 64071]]

    We granted reconsideration of our approach to account for these 
method biases to assess the true performance of the best performing 
sources. Reconsideration was appropriate because, as Sierra Club 
stated, we decided to correct the TCl data after the period for public 
comment on the proposed rule, and correcting the data significantly 
impacted the development of the TCl emission standards.
    To account for the bias in the analytic method, we corrected all 
TCl emissions data that were below 20 ppmv to 20 ppmv. We accounted for 
within-test condition emissions variability for the corrected data by 
imputing a standard deviation that is based on a regression analysis of 
run-to-run standard deviation versus emission concentration for all 
data above 20 ppmv. This approach of using a regression analysis to 
impute a standard deviation is similar to the approach we used to 
account for total variability (i.e., test-to-test and within-test 
variability) of particulate matter emissions for sources that use 
fabric filters.
1. Summary of the Final Action
    The comments to the reconsideration notice did not provide a basis 
for us to conclude that it was inappropriate to correct all TCl 
emissions data that were below 20 ppmv to 20 ppmv to account for 
potential systemic negative biases in the Method 0050 data. Therefore, 
we reaffirm our approach of correcting the TCl measurements at 
promulgation and are making no changes to the October 12, 2005 final 
rule.
2. What Are the Responses to Major Comments?
    Comment: Sierra Club (represented by Earthjustice) states that: (1) 
Establishing floor emission levels based on measurements below 20 ppmv 
that are corrected to 20 ppmv is impermissible because, even assuming 
bias in the analytic method, the corrected measurements do not reflect 
the performance of the best performing sources; (2) projecting the 
variability of emissions for the average of the best performing sources 
considering the variability of emissions for sources that are not best 
performing sources is inappropriate; (3) the ``statistical imputation'' 
methodology used to calculate emissions variability is inappropriate 
because EPA admits it overestimates variability; and (4) to the extent 
EPA relied on achievability as a reason to change the TCl standard, the 
Agency acted unlawfully.
    Response: We respond to each issue in turn:
    a. Corrected Measurements Do Not Reflect Performance of the Best 
Performing Sources. The best performing sources are those with 
measurements below 20 ppmv. We determined, however, and Sierra Club 
does not dispute, that those measurements are likely to be affected by 
a systemic negative bias in Method 0050 which collected these data so 
that the measured level of performance is biased low and therefore 
cannot credibly be deemed to reflect these sources' actual level of 
performance. 71 FR at 52629-30. Because measurements below 20 ppmv may 
not (indeed, likely do not) represent the performance of a source, we 
corrected the measurements to 20 ppmv, the only value of which there is 
any reasonable certainty. The corrected data thus are our best 
projection of the performance (not considering emissions variability) 
of those sources with the lowest measured TCl emissions, accounting for 
the bias in measurement.
    We note that the Clean Air Act requires EPA ``to make a reasonable 
estimate of the performance of the top 12 percent of units.'' CKRC v. 
EPA, 255 F.3d 855, 862 (D.C. Cir. 2001), citing Sierra Club v. EPA, 167 
F.3d 658, 662 (D.C. Cir. 1999) (interpreting 42 U.S.C. 7429(a)(2), 
which requires that ``emissions standards for existing units in a 
category * * * shall not be less stringent than the average emissions 
limitation achieved by the best performing 12 percent of units in the 
category''). The court has made clear that EPA has authority to devise 
the means of deriving this estimate, provided the method the Agency 
selects ``allow[s] a reasonable inference as to the performance of the 
top 12 percent of units.'' Id. Most importantly, though, EPA must show 
not only that it believes its methodology provides an accurate picture 
of the relevant sources' actual performance, but also why its 
methodology yields the required estimate. Id. We have explained the 
basis for the negative bias in the analytic method, the existence of 
which is not in dispute. The issue then becomes how best to estimate 
the performance of the best performing sources given that their 
measured performance reflects the bias of the analytic method. We 
believe that correcting potentially biased measurements to 20 ppmv is 
appropriate because Method 0050 itself states that the method is not 
acceptable for demonstrating compliance with HCl emission standards 
less than 20 ppm. \7,8\ TCl emission levels greater than 20 ppmv would 
be reported by Method 0050 without significant bias (and therefore are 
reliable measurements), while measurements reported to be below 20 ppmv 
may actually have been as high as 20 ppmv and cannot be reliably 
assessed below that number.
---------------------------------------------------------------------------

    \7\ See Method 0050, Section 1.2. Also, see equivalent Method 
26A, Section 13.1.
    \8\ As further evidence of the Method 0050 bias, the updated, 
equivalent method to Method 0050--Method 26A--states that that 
method has a possible measurable negative bias below 20 ppm HCl.
---------------------------------------------------------------------------

    Sierra Club does not suggest alternative approaches to correct the 
potentially biased measurements to project the performance of those 
sources, but rather implies that the uncorrected measurements should be 
used to establish the floor emission level. This would be arbitrary and 
inappropriate because those data almost certainly (no absolute 
certainty is possible) do not represent the performance of those 
sources due to analytic bias, and moreover, fail to account for 
emissions variability of the best performers.
    b. Projecting Emissions Variability Considering Sources Other Than 
the Best Performing Sources. We explained that, after correcting 
measurements below 20 ppmv to 20 ppmv, the corrected emission levels 
for the best performing sources naturally reflected little 
variability--corrected data for the best performing sources were 
generally the same values, on the order of 20 ppmv. 71 FR 52630/2. This 
had the effect of understating the variability associated with these 
data--i.e., these sources' performance. These sources' performance over 
time thus would not be assessed correctly, so some different type of 
estimate must be made. To address this problem, we performed a linear 
regression on the data base--including both best performing sources and 
other sources--charting standard deviation against emissions, and 
extrapolated the regression downward to the emission level for each 
best performing source to impute a standard deviation.
    Sierra Club states that it is inappropriate to use emissions 
variability for sources that are not best performing sources to project 
emissions variability for the best performing sources. We disagree here 
because we believe this is the best means of estimating the best 
performing sources' variability and hence their actual performance. See 
Sierra Club v. EPA, 479 F.3d 875, 882 (D.C. Cir. 2007) (EPA may 
consider variability of performers other than best if there is ``a 
demonstrated relationship between the two''). First, Sierra Club is not 
correct

[[Page 64072]]

that EPA is using variability of non-best performers as a proxy for the 
variability of the best performers. As just stated, EPA imputed the 
regression curve downward after examining all data and it is reasonable 
to do so because the relative standard deviation (i.e., variability of 
performance normalized for emission concentration) \9\ of the test 
condition runs of the better performing sources (i.e., sources with 
lower emissions) here was not significantly different from the relative 
standard deviation of the test condition runs of the worse performing 
sources.\10\ EPA reasonably assumed that this same relationship (i.e., 
the shape of the regression curve) would be the same at lower levels. 
The actual level of variability of the best performing sources 
resulting from this imputed regression curve shape is less for the best 
performing sources than for non-best sources. See generally, memorandum 
from Lucky Benedict, EERGC, to Bob Holloway, USEPA, entitled ``Analysis 
of Total Chlorine Data above 20 ppmv,'' dated March 21, 2007.
---------------------------------------------------------------------------

    \9\ Relative standard deviation is calculated as the standard 
deviation times 100 divided by the average, and is expressed as a 
percentage.
    \10\ As should be apparent from the following discussion, EPA is 
not using information on emission levels of worse performing sources 
to estimate the best performers' emission levels (the fact pattern 
of the Cement Kiln Recycling Coalition case and Brick MACT cases; 
see 255 F.3d at 865 and Brick MACT, 479 F.3d at 881-82).
---------------------------------------------------------------------------

    We have (uncorrected) variability results for several sources that 
performed close to the best performing sources--four sources emitted 
between 21 ppmv and 25 ppmv, and seven sources emitted between 21 ppmv 
and 28 ppmv. We considered using the variability of these sources as a 
surrogate for the variability for the best performers (i.e., those at 
20 ppmv) but were concerned that this may overstate best performers' 
variability and hence result in a standard which is too high (i.e., 
insufficiently stringent).\11\ Rather, we used variability results for 
all sources, irrespective of emission level, to develop a variability/
emissions regression curve. This curve regressed variability \12\ 
versus emissions through the low emitting sources that performed close 
to the best performers (e.g., including sources with emissions of 21 
ppmv and 24 ppmv, only slightly higher than the 20 ppmv for the best 
performers). We then extrapolated the curve down to the 20 ppmv 
emission level to impute a standard deviation for the best 
performers.\13\ As noted above, we determined that there is no 
significant difference in relative standard deviation for low emitting 
sources (e.g., sources emitting 21 ppmv to 38 ppmv) compared to high 
emitting sources (e.g., sources emitting 130 ppmv to 920 ppmv), and 
hence that it is reasonable to use all of the available data to derive 
a best fit shape of the regression curve.\14\ This similarity confirms 
that data on all sources' variability can reasonably be considered--by 
means of imputing the shape of the regression curve at the low end--in 
estimating the variability of the best performing sources.
---------------------------------------------------------------------------

    \11\ For example, the variability (i.e., standard deviation) of 
test condition runs generally increases as emission concentrations 
increase.
    \12\ We repeat that variability is measured as standard 
deviation.
    \13\ USEPA, ``Technical Support Document for HWC MACT Standards, 
Volume III: Selection of MACT Standards,'' September 2005, Section 
8-1.
    \14\ See memorandum from Lucky Benedict, EERGC, to Bob Holloway, 
USEPA, entitled ``Analysis of Total Chlorine Data above 20 ppmv,'' 
dated March 21, 2007.
---------------------------------------------------------------------------

    This approach does not substitute variability from non-best 
performers for variability of best performers. Rather, it uses all of 
the data to estimate how variability may change as performance improves 
to derive a best estimate of the variability of the best 
performers.\15\
---------------------------------------------------------------------------

    \15\ As it happens, if EPA were erroneously including 
information on variability of higher emitting sources in this 
analysis, it would result in a more stringent standard because the 
shape of the regression slope would be steeper and would cross the 
20 ppmv point at a lower point (because less variability would be 
imputed at lower emission concentrations). See Figure 1 in the 
memorandum cited in the preceding footnote. In fact, because (as 
explained in the text above) relative standard deviations of higher 
emitting sources do not increase as emissions increase, EPA does not 
believe it committed this type of error.
---------------------------------------------------------------------------

    c. Statistical Imputation Is Inappropriate Because It Overstates 
Variability. Sierra Club mistakenly believes that we used statistical 
imputation to project variability of the corrected data. As just 
discussed in section B.2.b., we used a linear regression analysis 
specifically because an alternative approach that we used to project 
variability of data sets containing nondetects--statistical 
imputation--would overstate variability of the corrected data. 71 FR at 
52630. We explained that the statistical imputation approach for 
correcting data below 20 ppmv without dampening variability would 
involve imputing a value between the reported value and 20 ppmv because 
the ``true'' value of the biased data would lie in this interval. This 
approach would be problematic, however, given that many of the reported 
values (based on the biased analytic method) were much lower than 20 
ppmv; the statistical imputation approach would tend to overestimate 
the run-to-run variability (leading to a standard higher than the one 
we are adopting) and hence we rejected its use in this context.
    d. Achievability of a Floor Emission Level. Sierra Club states that 
it is unlawful to consider whether a floor emission level is 
achievable. But the issue here is assessing sources' performance over 
time. If a best performing source on whose performance a MACT floor is 
based cannot itself comply with that floor standard, then that source's 
performance over time has been improperly assessed. Put another way, 
that source's variability (i.e., performance over time) has not been 
adequately accounted for. Mossville Environmental Action Now v. EPA, 
370 F. 3d 1232, 1241-42 (D.C. Cir. 2004). Since the standard must be 
met ``every day and under all operating conditions,'' it is imperative 
that the emission data used to represent the performance of the best 
performing sources truly represent the performance of those sources 
over time by, notably, accounting for emissions variability. Id. at 
1242.

C. Use of PS-11 and Procedure 2 as Guidance for Extrapolating the Alarm 
Set-Point of a Particulate Matter Detection System (PMDS)

    In its reconsideration petition, CKRC asked that EPA reconsider its 
references to Performance Specification 11 (PS-11) and Procedure 2 in 
the particulate matter detection system (PMDS) provisions of the 
October 12, 2005 final rule. We granted reconsideration because we 
developed the procedures for extrapolating the alarm set-point for PMDS 
that included references to PS-11 and Procedure 2, in response to 
comments on the proposed rule and after the period for public comment. 
71 FR at 52630-31.
    CKRC also stated that the reference to PS-11 for particulate matter 
Continuous Emissions Monitoring Systems (40 CFR Part 60, Appendix B) 
and Procedure 2 (Appendix F, Part 60) for use as guidance to implement 
provisions to extrapolate the alarm set-point of a PMDS may effectively 
prevent its members from utilizing this option due to significant 
technical difficulties and excessive costs.\16\ CKRC further stated 
that PS-11 and Procedure 2 contain a number of problems as they would 
apply to cement kilns, and that it has

[[Page 64073]]

filed a petition for review in the U.S. Court of Appeals for the D.C. 
Circuit challenging EPA's final rule adopting PS-11 and Procedure 2, 
which case is being held in abeyance.
---------------------------------------------------------------------------

    \16\ See letter from David P. Novello to Stephen L. Johnson 
regarding ``Petition for Reconsideration of Certain Provisions of 
Hazardous Waste Combustor MACT Replacement Standards Rule,'' dated 
December 9, 2005, p. 9, docket item EPA-HQ-OAR-2004-0022-0520.
---------------------------------------------------------------------------

    Finally, CKRC stated that use of a regression analysis approach to 
extrapolate the alarm set-point is not justified or necessary to 
establish an approximate correlation between the particulate matter 
detector system response and particulate matter concentrations. CKRC 
suggested that an alternative approach would be based on a linear 
relationship passing through zero and the mean of the PM comprehensive 
performance test results.
    When we reviewed the procedures in the final rule for establishing 
the set-point in light of CKRC's concerns regarding use of a regression 
analysis to extrapolate the set-point and use of PS-11 and Procedure 2 
as guidance, we identified several shortcomings of the final rule. 
Consequently, we proposed to revise the provisions for establishing the 
alarm set-point by extrapolation by: (1) Adding procedures to establish 
the alarm set-point for operations under the Documentation of 
Compliance; (2) revising procedures to extrapolate the alarm set-point 
for operations under the Notification of Compliance; and (3) providing 
specific rather than generic references to PS-11 and Procedure 2 
provisions that must be followed to extrapolate the alarm set-point. 71 
FR at 52631-33.
    We also determined that the final rule was silent on what operators 
must do when the PMDS (or bag leak detection system (BLDS)) is 
malfunctioning (e.g., when it is out of control or inoperable). We 
explained in the reconsideration proposal that it is reasonable to 
require that operations when the PMDS or BLDS is unavailable be 
considered the same as operations that exceed the alarm set-point given 
that there would be no information to conclude otherwise. Thus, we 
proposed to require sources to correct the malfunction or minimize 
emissions, and require that the duration of the malfunction be added to 
the time when the PMDS or BLDS exceeds the alarm set-point. If the time 
of PMDS or BLDS malfunction and exceedance of the alarm set-point 
exceeds 5 percent of the time during any 6-month block time period, the 
source would have to submit a notification to the Administrator within 
30 days of the end of the 6-month block time period that describes the 
causes of the exceedances and PMDS or BLDS malfunctions and the 
revisions to the design, operation, or maintenance of the combustor, 
air pollution control equipment, or PMDS (or BLDS) it is taking to 
minimize exceedances.
1. Summary of the Final Action
    We are today promulgating: (1) Revised procedures to extrapolate 
the PMDS alarm set-point which are less prescriptive than those we 
proposed in the reconsideration notice; (2) with respect to the 
excessive exceedance notification for the PMDS if the set-point is 
exceeded for more than five percent of the time during any 6-month 
block time period, a requirement, as proposed in the reconsideration 
notice, to also include the time the PMDS malfunctions (while the 
combustor is operating), as well as the time the PMDS set-point is 
exceeded; and (3) revised PMDS general requirements to clarify that, if 
the alarm set-point is exceeded or if the PMDS malfunctions, the source 
must take the corrective measures it specifies in its operating and 
maintenance plan required under Sec.  63.1206(c)(7).
    We discuss below the revised procedures to extrapolate the PMDS 
alarm set point. We discuss the other provisions--PMDS and BLDS 
malfunctions and clarification of general PMDS requirements--in the 
response to major comments below. Please note that the revised 
provisions are effective immediately, and today's final rule does not 
change the October 14, 2008 compliance date for existing sources 
established by the October 12, 2005 final rule. Sources can readily 
comply with the revised provisions promulgated today on the compliance 
time line established by the October 12, 2005 final rule.
    The revised procedures to extrapolate the PMDS alarm set point 
address four aspects: (1) Establishing the set-point for operations 
under the Documentation of Compliance; (2) establishing the set-point 
for operations under the initial Notification of Compliance; (3) PMDS 
quality assurance procedures; and (4) revising the set-point subsequent 
to periodic comprehensive performance testing and other testing, such 
as for quality assurance. See Sec.  63.1206(c)(9)(ii) through (v). In 
addition, please note that the final rule no longer references PS-11 or 
Procedure 2. We have concluded that the Relative Response Audit 
provisions of Procedure 2, and applying the correlation curve 
statistical parameters in PS-11, may not be appropriate in some 
situations. Accordingly, the final rule requires sources to recommend 
for approval site-specific procedures for PMDS quality assurance and to 
determine, as additional data pairs become available, when and how to 
evaluate correlation models that may better represent the relationship 
between reference method measurements and PMDS responses than a linear 
model.
    a. Documentation of Compliance Set-Point. To establish the set-
point for the Documentation of Compliance (DOC), the source must obtain 
a minimum of three reference method and PMDS data pairs, as proposed. 
71 FR at 52631/3. As proposed, a source: (1) May use existing data 
obtained within 60 months of the DOC; (2) must approximate the 
correlation of the reference method data to the PMDS data; (3) may 
assume a linear correlation; and (4) may use a zero-point. A source 
must request approval from the regulatory authority (in the continuous 
monitoring system test plan) of their determination whether multiple 
correlation curves will be necessary considering the design and 
operation of its combustor and PMDS (e.g., cement kilns equipped with 
an in-line raw mill and that use a light-scattering detector may need 
to establish separate correlation curves with the mill on and mill 
off).\17\ We are including this provision in the final rule in light of 
comments indicating that multiple correlation curves may be needed to 
appropriately correlate reference method and PMDS responses in some 
situations.\18\ As proposed, a source must establish the alarm set-
point as the PMDS response that corresponds to a PM concentration that 
is 50% of the PM emission standard or 125% of the highest PM 
concentration used to develop the correlation, whichever is greater. 
The PM emission concentration used to extrapolate the alarm set-point 
must not exceed the PM emission standard, however.
---------------------------------------------------------------------------

    \17\ USEPA, ``Current Knowledge of Particulate Matter (PM) 
Continuous Emissions Monitoring,'' September 8, 2000, p. 7-3.
    \18\ See letter from David P. Novello to Stephen L. Johnson 
regarding ``Petition for Reconsideration of Certain Provisions of 
Hazardous Waste Combustor MACT Replacement Standards Rule,'' dated 
December 9, 2005, p. 20, docket item EPA-HQ-OAR-2004-0022-0520.
---------------------------------------------------------------------------

    b. Initial Notification of Compliance Set-Point. To establish the 
set-point for operations under the initial Notification of Compliance, 
a source must request approval from the regulatory authority (in the 
continuous monitoring system test plan) of procedures they will use to 
establish an approximate correlation curve considering the three pairs 
of Method 5 or 5I data, the PMDS response data from the comprehensive 
performance test, and any additional data pairs, as warranted (e.g., 
data pairs during as-found operations; data pairs used for the 
Documentation of Compliance correlation curve). As

[[Page 64074]]

proposed, the final rule: (1) Requires sources to use a least-squares 
regression methodology to correlate PM concentrations to PMDS responses 
for data pairs; (2) allows sources to assume that a linear regression 
model approximates the relationship between PM concentrations and PMDS 
responses; and (3) requires sources to establish the alarm set-point as 
the PMDS response that corresponds to a PM concentration that is 50% of 
the PM emission standard or 125% of the highest PM concentration used 
to develop the correlation, whichever is greater. The emission 
concentration used to extrapolate the PMDS response must not exceed the 
PM emission standard. 71 FR at 52632-33.
    In addition, a source must request approval from the regulatory 
authority (in the continuous monitoring system test plan) of their 
determination whether multiple correlation curves are needed, 
considering the design and operation of the combustor and PMDS for 
reasons discussed above. If multiple correlation curves are needed, a 
source must request approval of the number of data pairs needed to 
establish those correlation curves and explain how the data will be 
obtained.
    We are not promulgating the proposed requirement to obtain three 
data pairs under as-found operations in addition to the performance 
test data pairs because the additional data may not significantly 
improve the assumed linear correlation model in all cases.\19\ Having 
three as-found data pairs would still result in too few data pairs to 
perform statistical analyses to identify the most appropriate 
correlation curve.\20\ Additional as-found data pairs may be warranted, 
however, in situations such as those where the extrapolated alarm set-
point correlates to a PM concentration close to the PM emission 
standard, or where a single correlation curve may be reasonable even 
though multiple curves may better represent the correlation. We 
conclude that it is more appropriate to make these determinations on a 
site-specific basis rather than mandate universal testing that may not 
be particularly useful.
---------------------------------------------------------------------------

    \19\ For example, additional as-found data pairs would not 
likely improve compliance assurance for sources that extrapolate the 
alarm set-point to a response that correlates to only 50% of the PM 
emission standard.
    \20\ Even with three as-found data pairs, there would be only 
nine data pairs available to establish the correlation curve--three 
data pairs from the DOC, three data pairs from the comprehensive 
performance test, and the three as-found data pairs. (There would be 
10 data pairs if a zero--point were used.) Procedure 2 for PM CEMS 
(Appendix F, Part 60) requires a minimum of 12 data pairs for a 
relative correlation audit. See Section 10.3(8).
---------------------------------------------------------------------------

    c. PMDS Quality Assurance. For PMDS quality assurance, a source 
must request approval from the regulatory authority (in the continuous 
monitoring system test plan) of the quality assurance procedures that 
will reasonably ensure that PMDS response values below the alarm set-
point do not correspond to PM emission concentrations higher than the 
value that correlated to the alarm set-point.\21\
---------------------------------------------------------------------------

    \21\ Please note that the rule also requires quality assurance 
procedures for sources that elect to establish the alarm set-point 
without extrapolation. In that situation, a source must request 
approval from the regulatory authority of the quality assurance 
procedures that reasonably ensure that PMDS response values below 
the alarm set-point do not correspond to PM emission concentrations 
higher than those demonstrated during the comprehensive performance 
test.
---------------------------------------------------------------------------

    Today's final rule requires a source to establish site-specific 
quality assurance measures rather than comply with the Relative 
Response Audit (RRA) provisions of Procedure 2 that apply to PM CEMS, 
which was required under the October 12, 2005 final rule and 
contemplated in the reconsideration proposal.\22\ For PM CEMS, a RRA is 
comprised of three pairs of reference method and PM CEMS responses at 
as-found operating conditions. For PMDS, the RRA would involve 
obtaining three pairs of reference method and PMDS responses. We now 
conclude, however, that all of the quality assurance provisions 
established for PM CEMS may not be appropriate for PMDS given that PMDS 
responses will only be approximately correlated to PM concentrations 
rather than direct measures of such; therefore PMDS correlations will 
not be subjected to the statistical criteria applicable to PM CEMS 
under section 13.2 of PS-11.
---------------------------------------------------------------------------

    \22\ Section 10.3(6) explains how a RRA is performed for a PM 
CEMS, Section 10.4(6) establishes the criteria for passing a RRA for 
a PM CEMS, and Section 10.5 establishes procedures for PM CEMS that 
fail the RRA.
---------------------------------------------------------------------------

    For example, one criterion under Procedure 2 for passing the RRA, 
section 10.4(6)(iii), as we considered adopting it for PMDS, would 
require that at least two of the three sets of PMDS and reference 
method measurements must fall within a specified area on a graph of the 
correlation regression line. The specified area on the graph of the 
correlation regression line is defined by two lines parallel to the 
correlation regression line, offset at a distance of 25 
percent of the numerical emission limit value from the correlation 
regression line. In retrospect, and in light of comments on the 
reconsideration notice, we have determined that this criterion would be 
inappropriate for a PMDS. The correlation regression line for a PMDS 
would generally comprise six data pairs when the alarm set-point is 
established in the initial Notification of Compliance, while the 
correlation regression line for a PM CEMS would comprise 15 data pairs 
initially, and if a Reference Correlation Audit, which requires 12 data 
pairs, had been performed, a total of 27 data pairs. Consequently, the 
PMDS correlation curve would not be as well defined as the PM CEMS 
correlation curve--6 data pairs versus 15 to 27 data pairs--and, thus, 
the RRA criterion for PM CEMS under section 10.4(6)(iii) would not be 
appropriate.
    Please note that a less precise correlation is appropriate for PMDS 
because they will be used for compliance assurance (i.e., as an 
indicator for reasonable assurance that an emission standard is not 
exceeded) rather than compliance monitoring (i.e., as an indicator of 
continuous compliance with an emission standard). As such, exceedance 
of a PMDS response that appears to correlate to a PM emission level 
exceeding the PM standard is not evidence of a violation of the 
emission standard. 70 FR at 59490-91.
    In the interim until more definitive guidance is available, we 
recommend that sources consider whether some of the RRA provisions of 
Procedure 2 may be appropriate for PMDS.
    d. Revising the Initial Notification of Compliance Set-Point. To 
revise the set-point subsequent to periodic comprehensive performance 
testing and other testing, such as for quality assurance, a source must 
propose to the regulatory authority for approval (in the continuous 
monitoring system test plan) an approach for how it will periodically 
revise the alarm set-point, considering the additional data pairs.
    We are promulgating a site-specific approach to revise the set-
point rather than the prescriptive approach proposed in the 
reconsideration notice (i.e., using the statistical parameters 
applicable to PM CEMS to identify the most appropriate correlation 
model). 71 FR at 52633/2. At proposal, we assumed that a minimum of 13 
data pairs would be available for applying the PM CEMS statistical 
parameters, and that the parameters could be applied to as few as 13 
data pairs. Under today's final rule, there could be as few as six data 
pairs \23\ (plus perhaps a zero-point)

[[Page 64075]]

available prior to any quality assurance testing that may be approved 
or required by the regulatory authority. Consequently, it would be 
appropriate to continue to apply the new data pairs obtained from 
quality assurance testing and periodic comprehensive performance 
testing to the linear correlation model until enough data pairs are 
available to warrant applying statistical parameters to determine if 
there is a more appropriate correlation model (e.g., logarithmic, 
exponential). In addition, the number of data pairs needed for 
meaningful statistical analysis will depend on factors including the 
range of the data. For example, if much of the data are representative 
of the high end of the range of normal operations (or only two modes of 
operation--normal within a narrow range and high-end), statistical 
analysis may not help identify the most appropriate correlation model. 
Thus, we conclude that these determinations should be made on a site-
specific basis.
---------------------------------------------------------------------------

    \23\ A minimum of three data pairs are needed for the 
Documentation of Compliance, and an additional three data pairs are 
needed for the initial Notification of Compliance (i.e., obtained 
during the comprehensive performance test).
---------------------------------------------------------------------------

    We note that sources can consider adding newly obtained data pairs 
to the pool of existing data pairs and continue to apply a linear 
correlation model to extrapolate the alarm-set-point until it obtains 
enough data representative of a range of PM concentrations that would 
warrant statistical analysis to identify the most appropriate 
correlation model. After a source obtains enough of these data pairs 
(e.g., 12 to 15), the statistical parameters that they should consider 
to identify the best correlation model include: The confidence interval 
half range percentage, the tolerance interval half range percentage, 
and the correlation coefficient. PS-11 provides definitions of these 
statistical parameters and other information that may be useful when 
evaluating correlation models.
2. What Are the Responses to Major Comments?
    Comment: CKRC states that eliminating general references to PS-11 
and Procedure 2 while including references to specific provisions of 
those procedures does not address their fundamental problem--PS-11 and 
Procedure 2 are problematic in a number of ways for cement kilns. CKRC 
believes it is unnecessary to include or even refer to specific 
procedures to be used when extrapolating the set-point. Instead, the 
facility and regulatory authority can and should be encouraged to 
develop appropriate procedures on a case-by-case basis. CKRC states 
that other extrapolation procedures may become available, and should 
not be excluded or precluded.
    Response: This is not the appropriate forum for addressing CKRC's 
challenges to PS-11 and Procedure 2. In response to comments received, 
however, the final rule no longer references PS-11 or Procedure 2. As 
discussed above, we have concluded that the RRA provisions of Procedure 
2, and applying the correlation curve statistical parameters in PS-11, 
may not be appropriate in some situations. Accordingly, the final rule 
requires sources to recommend for approval site-specific procedures for 
PMDS quality assurance and to determine, as additional data pairs 
become available, when and how to evaluate correlation models that may 
better represent the relationship between reference method measurements 
and PMDS responses than a linear model.
    Comment: CKRC states that it is inappropriate to sum times when the 
alarm set-point is exceeded and times that the PMDS is malfunctioning 
(and the source continues to operate). If the sum of these times 
exceeds 5 percent of the operating time in a 6-month block time period, 
the source would be required to submit an excess exceedance report to 
the regulatory authority. This would create unnecessary burdens and 
imply incorrectly that PM emissions may be excessive.
    Response: We explained in the reconsideration notice that it is 
reasonable to require that operations when the PMDS is unavailable be 
considered the same as operations that exceed the alarm set-point given 
that there would be no information to conclude otherwise. We maintain 
this view, and the commenter did not provide a basis for us to conclude 
that this requirement is inappropriate. In filing the excess exceedance 
report, however, the source is free to identify the portion of the 
exceedance time that was due to the PMDS malfunctioning.
    Comment: CKRC states that it is possible to improperly interpret 
Sec.  63.1206(c)(9)(ii)(C) in the October 12, 2005 final rule to 
require compliance with the alarm set-point, implying that an 
exceedance of the alarm set-point is a violation of the operating 
requirements.
    Response: We agree, and have revised the requirement to clarify 
that, if the alarm set-point is exceeded, the corrective measures 
specified in the operation and maintenance plan must be followed. See 
revised Sec.  63.1206(c)(9)(i)(G) through (I) and 63.1206(c)(9)(vii).

D. Tie-Breaking Procedure for New Source Standards

    The petition of the Coalition for Responsible Waste Incineration 
(CRWI) sought reconsideration of the tie-breaking procedure used to 
identify the single best performing source in cases where the MACT 
floor methodology identified multiple sources with the same single best 
System Removal Efficiency (SRE)/Feed aggregated scores.\24\ In the rare 
instances when a tie occurred, we selected the source with the lowest 
emissions (of the tied sources) as the criterion to break the tie. See 
70 FR at 59447 and 71 FR at 52634. As noted in CRWI's petition, this 
occurred for the mercury and low volatile metals new source standards 
for incinerators. Noting that EPA did not discuss the concept of 
selecting the source with the lowest emissions as the criterion to 
break ties (because this unusual situation did not occur at proposal), 
the CRWI argued in its petition that EPA had provided no opportunity to 
comment on the tie-breaking procedure. Pursuant to section 307(d)(7)(B) 
of the CAA, we granted the CRWI's petition for reconsideration.
---------------------------------------------------------------------------

    \24\ System removal efficiency is a measure of the percentage of 
HAP that is removed prior to being emitted relative to the amount 
fed to the unit from all inputs (e.g., hazardous waste, raw 
materials). For additional discussion of the SRE/Feed methodology, 
see 70 FR at 59441-447.
---------------------------------------------------------------------------

    As stated in the September 6, 2006 notice announcing 
reconsideration of this issue, the arguments the CRWI presented in its 
petition for reconsideration did not initially persuade us that our 
tie-breaking procedure--selecting the source (of the tied sources) with 
the lowest emissions as the single best performing source--was 
erroneous or inappropriate. 71 FR at 52634. However, because we did not 
discuss the concept of selecting the source with the lowest emissions 
as the criterion to break ties in the proposed rule, we decided to 
grant reconsideration on this issue and provide an opportunity for 
public comment on the tie-breaking procedure for new sources.
    In the notice of reconsideration, we requested comment on our 
decision to select the source (of all tied sources) with the lowest 
emissions as the single best performing source for purposes of new 
source floor determinations. We also specifically requested comment on 
alternative tie-breaking criteria including (1) using the single source 
(of the tied sources) with the best SRE; (2) selecting the single 
source (of the tied sources) with worst SRE; and (3) using some other 
form of averaging (e.g., the

[[Page 64076]]

99th percentile upper prediction limit) of the tied sources.
1. Summary of the Final Action
    The comments to the reconsideration notice did not provide a basis 
for us to conclude that the tie-breaking procedure used in the final 
rule was incorrect, impermissible, or otherwise flawed. Therefore, we 
reaffirm the validity of the determination made at promulgation and are 
making no changes to the final rule. Because we are retaining the same 
tie-breaking procedure as promulgated in the October 12, 2005 rule, the 
new source incinerator emission standards promulgated for mercury and 
low volatile metals under Sec.  63.1219(b)(2) and (b)(4) remain 
unchanged.
2. What Are the Responses to Major Comments?
    In response to the notice of reconsideration, we received four 
comment letters on this issue. These comment letters are available in 
the official public docket.\25\ A summary of major comments received on 
this reconsideration issue and EPA's responses to those comments are 
provided below.
---------------------------------------------------------------------------

    \25\ See comments 0565, 0567, 0569, and 0573 in the docket (EPA-
HQ-OAR-2004-0022).
---------------------------------------------------------------------------

    Comment: Three commenters state that EPA misconstrues the language 
of section 112(d)(3) of the CAA, especially the phrase ``best 
controlled similar source.'' These commenters argue that section 
112(d)(3) does not preclude the possibility that more than one source 
could be considered ``best.'' Moreover, EPA is not required to select 
the single best performing source in instances where EPA's floor 
methodology identifies more than one best performing source. Instead of 
applying a tie-breaking procedure, these commenters state that EPA 
should establish the floor at a level that all can meet (e.g., the 
highest emissions achieved among the tied sources).
    Response: We disagree with the commenters' interpretation of 
section 112(d)(3). As we explained in the reconsideration notice, we 
believe that the tie-breaking procedure adopted in the final rule is a 
reasonable interpretation of section 112(d)(3)'s language (it is, at 
the least, reasonable to interpret section 112(d)(3) to base the new 
source floor on the performance of a single source, since the provision 
refers to ``source'' singular, not plural). 71 FR at 52634. The 
commenter cites legislative history in support of its interpretation. 
H. Rep. No. 101-490 at 328. That legislative history refers to 
``similar sources'' after describing standards for new and existing 
sources, and the commenter views this language as supporting its view 
that the floor standard for new sources can be based on more than one 
best performing source. It is not clear that this passage is referring 
to new source standards, or whether instead that the plural reference 
is only meant to apply to existing sources. It is also not certain that 
the legislative history is even applicable, since it interprets a 
version of section 112(d)(3) not identical to the final version, and 
one which may have allowed consideration of costs at the floor level of 
control. See H. Rep. No. 101-490 at 328 (``In addition, EPA has to 
consider the above statutory factors, including costs, in determining 
stringency and similarity''). In any case, EPA is not aware of any 
compelling policy reason to adopt the commenter's interpretation. As 
explained in the reconsideration notice, basing the floor standard on 
the performance of a single source having the lowest emissions is an 
entirely reasonable means of selecting the best performing source among 
sources with best feedrate and system removal. 71 FR at 52634.
    Comment: These same commenters state that EPA is inconsistent in 
its application of the tie-breaking procedure to other standards. Two 
new source standards are cited by commenters as instances where EPA did 
not select a single best performing source among MACT pool sources. 
Specifically, the commenters refer to the total chlorine standards for 
new incinerators and the total chlorine standards for new liquid fuel 
boilers (for the category of sources that burn hazardous waste with an 
as-fired heating value less than 10,000 Btu/lb).
    Response: Both standards cited by the commenters are cases where 
nearly all available total chlorine data reflect the revised data 
handling procedure to account for method bias for total chlorine 
measurements below 20 ppmv. (See related discussion in section III.B 
above on this issue.) In these instances, we corrected all total 
chlorine measurements that were below 20 ppmv to 20 ppmv to establish 
the total chlorine floors.\26\ For incinerators, all 25 runs of total 
chlorine emissions data from the sources that comprise the MACT pool 
were corrected to 20 ppmv, and, in the case of liquid fuel boilers (low 
heating value subcategory), 17 of 18 runs were corrected to 20 ppmv. 
Given that both MACT pools of best performing sources (incinerators and 
liquid fuel boilers) comprised sources with the same level of 
performance from an emissions perspective (because nearly all of the 
best performing sources' emissions were adjusted to the same emissions 
level to account for bias in the analytic method), the case is not 
analogous to where performance among sources differ. The commenter's 
point also is without practical significance since an identical new 
source standard would have been promulgated regardless of source 
selected (given identical performance by the best performing sources).
---------------------------------------------------------------------------

    \26\ In addition, to address run-to-run variability given that 
nearly all runs for these data sets were corrected to 20 ppmv, we 
imputed a run standard deviation based on a regression analysis of 
run standard deviation versus total chlorine concentration for 
sources with total chlorine measurements greater than 20 ppmv. Thus, 
emissions at the upper prediction limit at a 99th percentile 
confidence level from these sources are identical.
---------------------------------------------------------------------------

    Comment: Three commenters state that the tie-breaking procedure is 
not reasonable because it is based on a method that produces arbitrary 
results and is impermissible under the statute. The commenters argue 
that breaking the tie based on emissions levels (of the tied sources 
for the mercury and low volatile metals standards) is inappropriate 
because such standards would arbitrarily reflect HAP levels in raw 
materials and fossil fuels. In addition, the tie-breaking procedure is 
impermissible because it imposes what amounts to beyond-the-floor 
standards without consideration of the beyond-the-floor factors (e.g., 
the floors identified by EPA would require one or more of the tied 
source having to install upgraded air pollution control equipment to 
achieve the floor) including costs, energy, and non-air health and 
environmental impacts.
    Response: We disagree with the commenters' statement that the 
mercury and low volatile metals standards represent de facto beyond-
the-floor standards. In EPA's view, a purported floor standard which 
forces the best performer on whose performance the floor standard is 
based to change its practices is a de facto beyond-the-floor new source 
standard (or, put another way, has mis-assessed the source's 
performance). This is not the case for the mercury and low volatile 
metals standards for new incinerators. These standards reflect the 
performance of a combination of front end control (limiting the 
feedrate of mercury in the hazardous waste) and back end control 
(performance of a control technology such as particulate matter 
control). Sources have the ability to control emissions of mercury (and 
low volatile metals) by either of these control techniques as did the 
single best performing source as identified by our tie-breaking 
procedure (of the tied

[[Page 64077]]

sources). Thus, we have not improperly estimated the performance of the 
best performing source since that source is capable of replicating its 
own performance.

E. New Source Particulate Matter Standard for New Cement Kilns

    In the October 12, 2005 final rule, we based the particulate matter 
standard for new cement kilns on emissions data from the Ash Grove 
Cement Company kiln located in Chanute, Kansas (Ash Grove Chanute) and 
promulgated a standard of 0.0023 gr/dscf.\27\ The petitions of the Ash 
Grove Cement Company and the Cement Kiln Recycling Coalition requested 
that EPA reconsider the 0.0023 gr/dscf standard for new cement 
kilns.\28\ The petitioners stated that the 0.0023 gr/dscf standard was 
not properly noticed because we did not discuss using the emissions 
data from Ash Grove Chanute as part of the new source MACT cement kiln 
floor analysis in the April 20, 2004 proposed rule.\29\ However, the 
particulate matter data from Ash Grove Chanute was considered (in fact, 
it was the single best performing source upon which the 0.0023 gr/dscf 
standard was based) in the particulate matter MACT floor analysis in 
the final rule. 70 FR at 59419.
---------------------------------------------------------------------------

    \27\ See USEPA, ``Technical Support Document for HWC MACT 
Standards, Volume III: Selection of MACT Standards,'' September 
2005, Appendix F, Table ``APCD-CK-PM.'' The Ash Grove Chanute test 
data were from performance testing conducted in December 2001 and 
March 2002.
    \28\ The petitions for reconsideration for the Ash Grove Cement 
Company and the Cement Kiln Recycling Coalition are included in the 
docket (EPA-HQ-OAR-2004-0022). See docket items 0516 and 0520, 
respectively.
    \29\ In the 2004 proposed rule, we stated that it was not 
appropriate to use the Ash Grove Chanute data for the MACT floor 
analysis for existing sources. 69 FR at 21217 n. 35. While the 
proposed rule was thus clear that available particulate matter data 
from Ash Grove Chanute would not be used in the MACT floor analysis 
for existing sources, we did not state whether or not these data 
would be evaluated in the new source floor analysis. Thus, no 
revision of the standard is necessary.
---------------------------------------------------------------------------

    Pursuant to section 307(d)(7)(B) of the CAA, we granted 
reconsideration of the new source particulate matter standard for new 
cement kilns. 71 FR 14665. Reconsideration of the standard was 
appropriate because we adopted the calculation using particulate matter 
emissions data from the Ash Grove Chanute plant after the period for 
public comment on the proposed rule. In addition, the petitioners 
argued that the particulate matter standard of 0.0023 gr/dscf was 
derived using unrepresentative test data from Ash Grove Chanute, 
resulting in a standard that the source itself could not achieve. To 
support their position, petitioners provided additional particulate 
matter performance data from the Ash Grove Chanute plant.
    In the notice of reconsideration, we stated that ``it appears that 
the promulgated new source standard for particulate matter for cement 
kilns is overly stringent in that it does not fully reflect the 
variability of the best performing source over time (the ``emission 
control that is achieved in practice,'' using the language of section 
112(d)(3)).'' 71 FR at 14668. Incorporating the newly submitted 
particulate matter data from the Ash Grove Chanute plant into the MACT 
floor analysis, we proposed a revised particulate matter standard for 
new cement kilns of 0.0069 gr/dscf. 71 FR at 14669-70. We also proposed 
revisions to the particulate matter standards for new incinerators and 
liquid fuel boilers (Id.). As discussed in the reconsideration notice, 
the MACT floor methodology for particulate matter includes a 
``universal variability factor'' to address long-term variability in 
particulate matter emissions of sources using fabric filters. 71 FR at 
14668 and 70 FR at 59440.\30\ When we included the newly submitted Ash 
Grove Chanute data in the universal variability factor analysis, the 
long-term variability relationship changed, which led to the proposed 
(small) changes to the incinerator and liquid fuel boiler new source 
particulate matter standards.
---------------------------------------------------------------------------

    \30\ The universal variability factor relationship is not 
developed for each source category, but is based on relevant data 
from all hazardous waste combustor source categories. See 
``Technical Support Document for HWC MACT Standards, Volume III: 
Selection of MACT Standards,'' September 2005, Sections 5.3 and 7.4.
---------------------------------------------------------------------------

1. Summary of the Final Action
    We are today promulgating revised new source standards for 
particulate matter for cement kilns and incinerators that burn 
hazardous waste. The revised particulate matter standards for new 
cement kilns and new incinerators are 0.0069 gr/dscf and 0.0016 gr/
dscf, corrected to 7 percent oxygen, respectively. These amendments 
revise 40 CFR 63.1219(b)(7) and 63.1220(b)(7)(i).
    We are not, however, revising the particulate matter standard for 
new liquid fuel boilers as proposed. In the March 23, 2006 
reconsideration notice, we proposed to revise the particulate matter 
standard to 0.0088 gr/dscf (20 mg/dscm) from 0.0087 gr/dscf (20 mg/
dscm) as a result of a minor change in the universal variability factor 
relationship. 71 FR at 14670. In a subsequent action, we decided to 
express all particulate matter standards in the same format used in the 
October 12, 2005 final rule. See 73 FR at 18973 (April 8, 2008). In the 
case of liquid fuel boilers, this would be in the units of mg/dscm. 
Since the standard promulgated in the October 2005 rule and the 
standard calculated in the reconsideration proceedings are identical--
20 mg/dscm--no change in the standard is necessary.
    As proposed, we are amending the compliance date requirements under 
40 CFR 63.1206 to require that new cement kilns (i.e., sources that 
commenced construction or reconstruction after April 20, 2004, the date 
of the rule proposing the full set of MACT standards for cement kilns) 
comply with the revised particulate matter standard by the later of 
October 28, 2008 or the date the source starts operations. 71 FR at 
14671. See amendments to 40 CFR 63.1206(a)(1)(ii)(B). In addition, we 
are not amending the compliance date requirements for new incinerators 
for reasons discussed in the proposed rule (Id.).
2. What Are the Responses to Major Comments?
    We received fifteen comment letters in response to the notice of 
reconsideration. These comment letters are available in the official 
public docket. A summary of major comments received on this 
reconsideration issue and EPA's responses to those comments are 
provided below.
    Comment: One commenter points out that EPA characterized the newly 
submitted data by Ash Grove Chanute as ``normal'' in the March 2006 
reconsideration notice and states that it is arbitrary and capricious 
to include any emissions data characterized as other than ``compliance 
test'' (e.g., ``normal'' or ``in-between'' data) in the MACT floor 
analysis for particulate matter.\31\ According to the commenter, EPA's 
established methodology for particulate matter only considers data 
characterized as ``compliance test.'' As an example, the commenter 
cites the incinerator analysis included in the October 2005 rule as 
evidence that EPA inappropriately departed in the reconsideration 
notice from the established MACT floor methodology for particulate 
matter. In addition, the commenter states that it is inappropriate to 
include in the MACT floor analysis data rated as other than 
``compliance test'' due to regulatory oversight and statistical 
variability considerations.

[[Page 64078]]

Finally, the commenter states that other source categories should also 
be afforded the same opportunity to submit ``normal'' emissions data 
for inclusion in the floor analyses.
---------------------------------------------------------------------------

    \31\ We classified emissions data of each test condition for 
each pollutant in one of four ways: ``compliance test,'' ``normal,'' 
``in between,'' and ``not applicable.'' 69 FR at 21218-19.
---------------------------------------------------------------------------

    Response: While it is true that we do not consider ``normal'' 
emissions data for some MACT floors, we disagree with the commenter 
that the particulate matter standards are based solely on data rated as 
``compliance test.'' The MACT floor standards for particulate matter 
are identified using the Air Pollution Control Technology (APCD) 
methodology. See 70 FR at 59447; see also Section III.A of September 
27, 2007 notice (72 FR at 54878). For reasons discussed in the 
technical support document, the APCD approach only considers 
``compliance test'' emissions data for sources not equipped with fabric 
filters. However, for fabric filter equipped sources, all available 
valid emissions data, including those rated as ``normal'' (i.e., day-
to-day, as opposed to compliance test data) are included in floor 
analysis for particulate matter.32 33 Given that Ash Grove 
Chanute uses a fabric filter to control emissions of particulate 
matter, it is appropriate to include in the MACT floor analysis 
available emissions data rated as ``normal,'' which we did in the 
reconsideration notice. Therefore, we disagree with the commenter that 
we deviated from the established APCD approach methodology in the March 
2006 reconsideration notice.
---------------------------------------------------------------------------

    \32\ See USEPA, ``Technical Support Document for HWC MACT 
Standards, Volume III: Selection of MACT Standards,'' September 
2005, Section 7.4, and also Section 5.3. Valid emissions data 
includes those characterized as ``compliance test,'' ``normal,'' and 
``in between.''
    \33\ We concluded in the October 12, 2005 rule that normal 
emissions data from fabric filter-equipped sources should also be 
included in the particulate matter floor analysis because 
particulate matter emissions are relatively insensitive to baghouse 
inlet loading and operating conditions. 70 FR at 59424.
---------------------------------------------------------------------------

    We also note that the commenter is incorrect in stating that the 
incinerator MACT floor standards for particulate matter are based only 
on ``compliance test'' data. Eleven fabric filter-equipped sources 
comprise the MACT pool for incinerators. When evaluating the floor for 
particulate matter, available emissions data from all sources but one 
(source no. 3000) included either ``normal'' or ``in between'' data in 
the analysis.\34\
---------------------------------------------------------------------------

    \34\ USEPA, ``Technical Support Document for HWC MACT Standards, 
Volume III: Selection of MACT Standards,'' September 2005, Appendix 
F, Table APCD-INC-PM. For example, the single best performing source 
was source no. 341, whose valid particulate matter performance data 
include both ``compliance test'' data (condition C10) and ``in 
between'' data (condition C12). Another best performing incinerator 
in the MACT pool was source 3010 that included a total of nine valid 
test conditions (one ``compliance test,'' five ``normal,'' and three 
``in between''). Individual test condition ratings can be found in 
the hazardous waste combustor database. See docket item EPA-HQ-OAR-
2004-0022-0433.
---------------------------------------------------------------------------

    Finally, we disagree that it is inappropriate to include ``normal'' 
and ``in between'' emissions data from fabric filter-equipped sources 
in the APCD approach analysis. As discussed in the October 12, 2005 
rule, particulate matter emissions from fabric filter-equipped sources 
are more difficult to maximize (compared to other control equipment) 
during compliance testing because particulate matter emissions are 
relatively insensitive to fabric filter inlet loadings and operating 
conditions.\35\ As a result, in addition to ``compliance test'' data, 
we also used ``normal'' and ``in between'' rated emissions data from 
fabric filter-equipped sources. We did this not only for cement kilns, 
but also for other source categories with best performing sources 
equipped with fabric filters. Given that the particulate matter floor 
analysis was applied equally to all source categories, the commenter's 
suggestion of revising the MACT floor standards for other source 
categories is without merit.
---------------------------------------------------------------------------

    \35\ USEPA, ``Technical Support Document for HWC MACT Standards, 
Volume III: Selection of MACT Standards,'' September 2005, Section 
5.3.
---------------------------------------------------------------------------

    Comment: One commenter states that it is arbitrary for EPA to 
revise the particulate matter MACT floor standard based on the 
selective use of new data from one source (i.e., the data submitted by 
Ash Grove Chanute). According to the commenter, EPA must collect data 
from all cement kiln sources. The commenter also states that it was 
arbitrary and capricious for EPA to accept the newly submitted data 
(showing higher emissions of particulate matter) for the Ash Grove 
Chanute kiln while refusing to consider or collect other emissions data 
from other newly constructed cement kilns that may refute the claim 
that new baghouses inevitably deteriorate.
    Response: First, the commenter's belief that the proposed revision 
was based entirely on ``new'' data--data for periods after EPA closed 
the data information record--is not correct. The most salient data 
indicating that the source's performance over time had been 
mischaracterized comes from 2003, within the period for which EPA 
accepted performance data. The data showed the Ash Grove Chanute test 
average over two tests to be 0.0062 gr/dscf (without any statistical 
adjustment for variability), higher than its predicted maximum 
performance of 0.0023 gr/dscf.\36\ These data would have been presented 
to EPA and included in the data base for the promulgated rule had EPA 
provided proper notice, and would have necessarily changed the estimate 
of the performance of the Ash Grove Chanute kiln.
---------------------------------------------------------------------------

    \36\ Incidentally, these data are yet another instance where 
performance tests failed to accurately characterize a source's 
performance (despite the commenter's reiterated assertions that such 
tests account for all variability because they are conducted under 
so-called worst-case conditions). Indeed, in this instance, even the 
EPA-predicted level of 0.0023 gr/dscf (which is a value reflecting 
statistical adjustment to account for both short-term and long-term 
variability) did not adequately account for the source's long-term 
variability.
---------------------------------------------------------------------------

    Second, the remaining information was presented to EPA in the 
context of reconsideration, and EPA had no choice but to consider it. 
Nor was EPA's consideration of the new information arbitrary. EPA did 
not selectively seek new information to alter a standard, nor did an 
industry group selectively present data to EPA which it could have 
presented during the rulemaking. Nor did EPA review only ``cherry-
picked'' data on the performance of the relevant source. Rather, EPA 
has reasonably considered all of the information on the performance of 
the source characterized as ``best controlled'', which source's 
performance formed the sole basis for the new source standard at issue.
    Comment: Two commenters state that the particulate matter standard 
of 0.0023 gr/dscf (the standard promulgated in the October 12, 2005 
rule) is readily achievable by cement kilns and should not be revised. 
These commenters state that it is arbitrary and capricious for EPA to 
use the new Ash Grove Chanute data because the higher emission levels 
seen with the 2003-2005 data may be the result of other factors besides 
normal deterioration of a new baghouse after the initial break-in 
period. The commenters suggest other explanations for the higher 
emissions including: (1) Ash Grove Chanute had no regulatory incentive 
to optimize the kiln's performance in subsequent tests because the 
source was subject to an emission standard that is less stringent than 
0.0023 gr/dscf; and (2) Ash Grove Chanute does not use a baghouse leak 
detection system with its baghouse that would have allowed it to detect 
and fix smaller leaks. Therefore, according to the commenters, the 
possibility that Ash Grove Chanute allowed the kiln's performance to 
deteriorate by failing to install testing equipment and conduct 
necessary maintenance is at least as plausible as normal degradation of 
a new baghouse after the initial break-in period.

[[Page 64079]]

    Response: We disagree with the comment that a particulate matter 
standard of 0.0023 gr/dscf represents the performance of the best 
performing source, considering performance variability, for new cement 
kilns, based on available data and information. The MACT floor standard 
is to be based on actual performance data (accounting for variability), 
not as the commenter would have it on what could be achieved by using 
other control methods not in use at the best performing source (e.g., a 
bag leak detection system at Ash Grove Chanute).\37\ The question of 
what the best performer would do if it were equipped differently is 
legally irrelevant in establishing a floor for new sources since it 
does not relate to the best performing source's actual performance. The 
Ash Grove Chanute data from 2003-2005 show that the source we 
identified as the single best performer in the October 12, 2005 rule--
Ash Grove Chanute--cannot achieve the 0.0023 gr/dscf standard 
promulgated in that rule when it operates under the operation and 
maintenance practices that were required and otherwise appropriate for 
the source.\38\ In other words, the promulgated standard demonstrably 
did not account for the source's legitimate operating variability--its 
performance over time when operated and maintained properly.
---------------------------------------------------------------------------

    \37\ In fact, and as acknowledged by the commenters, no cement 
kilns are currently using a bag leak detection system with their 
kiln baghouse.
    \38\ At the time of testing, the fabric filter performance was 
maintained by compliance with an opacity standard.
---------------------------------------------------------------------------

    We also disagree that Ash Grove Chanute allowed its kiln's 
performance to deteriorate during subsequent testing in 2003-2005 
because there was no regulatory incentive to optimize the kiln's 
performance. The commenters speculate that because Ash Grove Chanute 
operated at particulate matter levels so far below allowable levels in 
2001-2002, Ash Grove could have been less concerned with tuning, 
optimizing and maintaining the baghouse for the 2003-2005 testing. The 
applicable regulations require the kiln to be properly operated and 
designed. Thus, Ash Grove Chanute required to maintain good air 
pollution control practices for minimizing emissions during the 2003-
2005 testing (e.g., see Sec. Sec.  63.6(e)(1) and 63.1206(c)(7)).
    The emission data themselves do not support the commenters' claim 
and support that the source was properly operated. First, the kiln's 
performance did not ``deteriorate'' over time. The kiln had lower 
emission levels when tested in 2005 (and 2004) than it did during the 
2003 tests.\39\ When the kiln was tested on successive days in 2005, 
the nine test runs conducted over a consecutive three day period show 
that average emissions of particulate matter decrease from the previous 
day: Day one emissions averaged 0.0060 gr/dscf, day two averaged 0.0035 
gr/dscf, and emissions on day three averaged 0.0017 gr/dscf.\40\ These 
test results showing ``improved'' performance combined with Ash Grove 
Chanute's statements that there were no changes in the maintenance of 
the air pollution control equipment during the three days of testing do 
not support the commenter's argument that Ash Grove Chanute's 2003-2005 
data reflect an ineffective ongoing maintenance program. Indeed, the 
day three results are among the lowest emissions achieved by the source 
in our data base.\41\ Thus, neither the claimed lack of a regulatory 
incentive to maintain levels achieved in 2001-2002 nor failure to 
maintain the air pollution control system would explain why particulate 
matter emissions ``improved'' over this three day period, or 
``improved'' between 2003 and 2005. The obvious explanation is that 
these varying results illustrate the source's normal operating 
variability.
---------------------------------------------------------------------------

    \39\ The data were: One test condition conducted in December 
2003 averaged 0.0062 gr/dscf; a second test condition conducted in 
September 2004 averaged 0.0015 gr/dscf, and three test conditions 
conducted in November 2005 averaged 0.0060, 0.0035, and 0.0017 gr/
dscf, respectively. These are actual measurements, and do not 
include adjustments for run-to-run variability, or application of 
the Universal Variability Factor.
    \40\ We note that the day three particulate matter results are 
only slightly higher than levels achieved in 2002: 0.0017 gr/dscf 
vs. 0.0013 gr/dscf.
    \41\ See docket item EPA-HQ-OAR-2004-0022-0546.1, page 9.
---------------------------------------------------------------------------

    Comment: One commenter claims that Ash Grove Chanute's 2003-2005 
emissions data resulted from tests that were not conducted under the 
same operating conditions as the initial tests in late 2001 and early 
2002. According to the commenter, varying combustion gas flow rates and 
process conditions explain the higher particulate matter emissions in 
the 2003-2005 data.
    Response: Hazardous waste combustor sources are subject to site-
specific operating requirements that must be maintained in order to 
ensure continued compliance with the hazardous waste combustor MACT 
standards, including the particulate matter standard. These operating 
requirements are established during a compliance test when sources 
generally operate under conditions that are at the extreme high end of 
the range of normal operations. Sources do this to provide themselves 
operating flexibility for day-to-day operations while complying with 
the rule's standards and operating requirements. While operating 
conditions may vary among the available Ash Grove Chanute data, the 
2003-2005 data were generated while operating within the limits 
established during the compliance test. Therefore, we reject the 
suggestion that the data are not reflective of Ash Grove Chanute's 
performance over time.
    Comment: The same commenter states that EPA based the proposed 
standard of 0.0069 gr/dscf on a cement kiln source (Giant Cement 
Company, SC) that ceased operations in 2005. The commenter notes that 
this is inappropriate and inconsistent with the approach discussed in 
the October 12, 2005 final rule whereby EPA concluded that MACT floor 
standards should be based only on the performance of sources that 
actually are operating (i.e., burning hazardous waste). 70 FR at 59419.
    Response: We agree with the commenter that this source ceased 
operations in 2005. While we continue to believe that the approach to 
exclude ``no longer operating sources'' from the MACT floor analysis is 
appropriate, we believe this situation is different given that the vast 
majority of standards are not at issue in these reconsideration 
proceedings. We also note that the MACT floor standard for new cement 
kilns would increase slightly (the commenter evidently assumed a 
decrease) to 0.0071 gr/dscf if we were to make the data base change the 
commenter suggests.

F. Beyond-the-Floor Analyses to Consider Multiple HAP That Are 
Similarly Controlled

    The petition of the Sierra Club sought reconsideration of several 
beyond-the-floor determinations, including beyond-the-floor analyses to 
consider multiple HAP that are controlled by a single control 
mechanism. One of the concerns was whether EPA had adequately complied 
with public notice and comment requirements regarding the beyond-the-
floor evaluations included in the October 12, 2005 final rule. Noting 
that EPA had included a new revised beyond-the-floor analysis (in 
response to the petitioner's comments to the April 20, 2004 proposed 
rule) in the final rule, the Sierra Club argued that EPA had provided 
no opportunity to comment on the revised beyond-the-floor analysis. 
Pursuant to section 307(d)(7)(B) of the CAA, we granted the Sierra 
Club's petition for reconsideration with respect to beyond-the-floor 
analyses to consider multiple

[[Page 64080]]

HAP that are controlled by a single control mechanism.\42\
---------------------------------------------------------------------------

    \42\ In its petition for reconsideration, the Sierra Club also 
requested that EPA reconsider beyond-the-floor standards based on 
wet and dry scrubbing. We denied the Sierra Club's petition to 
reconsider these rule provisions for reasons discussed in a letter 
to Sierra Club. See docket item EPA-HQ-OAR-2004-0022-0558 (August 
22, 2006).
---------------------------------------------------------------------------

    In the notice of reconsideration, we requested comment on a revised 
beyond-the-floor analysis whereby we evaluated the achievability, 
within the meaning of section 112(d)(2) of the CAA, of beyond-the-floor 
standards for all HAP for each source category or subcategory. 71 FR at 
52635. We called this analysis the ``comprehensive beyond-the-floor 
analysis'' (or comprehensive analysis). Id. In general, the 
comprehensive analysis was an evaluation of beyond-the-floor control 
options that would achieve emission reductions of all HAP, based on 
what we consider reasonable assumptions of performance of each control 
method, from levels achieved at the MACT floor. Evaluated control 
methods included techniques such as activated carbon injection or 
carbon beds, improved or new particulate matter control equipment, and 
acid gas scrubbing devices.
    Given that some control methods are capable of achieving reductions 
of multiple HAP, we apportioned the costs of a specific control method 
(e.g., an activated carbon injection system) among the HAP that it 
would control. Control method costs are apportioned on a source-by-
source basis to those HAP requiring emission reductions to achieve the 
beyond-the-floor standard. We did this because some control methods are 
more achievable (within the meaning of section 112(d)(2)) than other 
methods. In addition, apportioning costs of control to each HAP allowed 
us to determine that beyond-the-floor standards are warranted for a 
subset of HAP for a given category or subcategory in cases where 
adopting beyond-the-floor standards for all HAP (the comprehensive 
analysis) was not justified. For example, based on the results of the 
comprehensive analysis at proposal for the existing source solid fuel 
boiler category, we tentatively rejected setting beyond-the-floor 
standards for all HAP because we judged the suite of standards as 
unachievable.\43\ However, based on our proposed methodology to 
apportion control costs, we judged the beyond-the-floor standard for 
particulate matter as achievable.\44\
---------------------------------------------------------------------------

    \43\ The aggregate total annualized cost of the comprehensive 
analysis was $8.8 million and would result in the following emission 
reductions: 0.3 g TEQ of dioxin/furans; 468 tpy of particulate 
matter; 0.03 tpy of mercury; 0.47 tpy of semivolatile metals; 0.52 
tpy of low volatile metals; 794 tpy of total chlorine; and 0.97 tpy 
of non-dioxin/furan organic HAP. See July 2006 technical support 
document supporting the reconsideration notice (Appendix A, page 10 
of 37 and Table 4-4, page 4-6).
    \44\ The beyond-the-floor analysis of particulate matter alone 
resulted in total annualized costs of $1.5 million and would result 
in a reduction of 468 tpy of particulate. These estimates equate to 
a cost-effectiveness of $2,569 per ton of particulate matter, which 
we proposed to be justified (Appendix A, page 3 of 37).
---------------------------------------------------------------------------

1. Summary of the Final Action
    After careful consideration of the comments, we are reaffirming 
most of the beyond-the-floor determinations made at promulgation of the 
October 12, 2005 final rule and initially determined not to change in 
the subsequent reconsideration notice. That is, we continue to conclude 
that several beyond-the-floor standards are achievable, namely the 
beyond-the-floor standards for particulate matter for existing and new 
solid fuel boilers. However, because we have determined for independent 
reasons not to defend the dioxin/furan standards for liquid fuel 
boilers (see section IV.D below), that issue has become moot. These 
beyond-the-floor standards were promulgated in the October 12, 2005 
final rule. In addition, we are concluding that beyond-the-floor 
standards for the remaining standards (of those EPA is defending) are 
not warranted.\45\ Therefore, we are making no changes to the final 
rule as a result of reconsideration of the beyond-the-floor standards.
---------------------------------------------------------------------------

    \45\ USEPA, ``Technical Support Document for HWC MACT Standards: 
Petitions for Reconsideration Support Document,'' February 2008, 
Section 4.
---------------------------------------------------------------------------

2. What Are the Responses to Major Comments?
    In response to the notice of reconsideration, we received seven 
comment letters on this issue. These comment letters are available in 
the official public docket.\46\ A summary of major comments received on 
this reconsideration issue and EPA's responses to those comments are 
provided below.
---------------------------------------------------------------------------

    \46\ See comments 0563, 0564, 0565, 0567, 0568, 0569, and 0573 
in the docket (EPA-HQ-OAR-2004-0022).
---------------------------------------------------------------------------

    Comment: Regarding EPA's rejection of several beyond-the-floor 
analyses that included a cost-effectiveness evaluation of the beyond-
the-floor standard, one commenter states that the CAA requires that 
EPA's standards must reflect the ``maximum'' degree of reduction that 
is achievable considering the ``cost of achieving such emission 
reduction'' and any non-air quality health and environmental impacts 
and energy requirements. According to the commenter, the only relevant 
factors regarding the cost measures are (1) whether it is too costly to 
be ``achievable;'' and (2) whether it would yield additional 
reductions, so that EPA's standard would not reflect the ``maximum'' 
achievable degree of reduction without it. The commenter further states 
that cost-effectiveness is not relevant to either of these questions 
and that cost-effectiveness is not a metric for cost.
    Response: We disagree with the commenter's interpretation. We 
addressed a comment similar to this one in a recent final rule for the 
Portland Cement Manufacturing NESHAP. 71 FR at 76534 (December 20, 
2006). For readers' convenience, our response is repeated below:
    The statute requires that EPA consider ``the cost of achieving such 
emission reduction``(section 112 (d)(2)) in determining the maximum 
emission reduction achievable. This language does not mandate a 
specific method of taking costs into account, as the commenter would 
have it, but rather leaves EPA with significant discretion as to how 
costs are to be considered. See Husqvarna AB v. EPA, 254 F.3d 195, 200 
(D.C. Cir. 2001). In that case, the court interpreted the requirement 
in section 213(a)(3) of the CAA (which mirrors the language in section 
112(d)(2)) that nonroad engines ``achieve the greatest degree of 
emission reduction achievable through the application of [available] 
technology * * * giving appropriate consideration to the cost of 
applying such technology,'' and held that this language ``does not 
mandate a specific method of cost analysis.'' The court therefore 
``f[ound] reasonable EPA's choice to consider costs on the per ton of 
emissions removed basis.''
    Moreover, where Congress intended that economic achievability be 
the means of assessing the reasonableness of costs of technology-based 
environmental standards, it says so explicitly. See Clean Water Act 
section 301(b)(2)(A) (direct dischargers of toxic pollutants to 
navigable waters must meet standards reflecting ``best available 
technology economically achievable''). There is no such explicit 
directive in section 112(d)(2). EPA accordingly does not accept the 
commenter's interpretation.
    Comment: The same commenter argues that the concept of cost-
effectiveness is at odds with the mandate of section 112(d)(2) that

[[Page 64081]]

requires beyond-the-floor standards to reflect the ``maximum'' 
achievable degree of reduction. According to the commenter, cost-
effectiveness is an inherently subjective measure that compares 
``cost'' with a benefit (the amount of pollution reduced). By asserting 
discretion to set a beyond-the-floor standard at a level yielding not 
the ``maximum'' degree of reduction that is ``achievable'' but, 
instead, the degree of reduction that EPA believes is cost-effective, 
the commenter argues that EPA alters the statutory mandate and defeats 
Congress's purpose.
    Response: First, the commenter is simply not correct that section 
112(d)(2) precludes EPA from considering cost-effectiveness as a means 
of evaluating costs. In addition to the authority cited in the previous 
response, see Bluewater Network v. EPA, 372 F.3d 404, 411, (D.C. Cir. 
2004) a case interpreting the same statutory language described in the 
previous response (section 213(a)(3) of the Act), which is 
substantially identical to the language in section 112(d)(2). Rejecting 
an argument that EPA must require the greatest technically achievable 
reductions immediately, the court stated ``the lesson from Husqvarna * 
* * is not that the EPA must adopt the most stringent standards based 
on the most advanced control technologies but that the EPA is to arrive 
at standards that reduce emissions to the greatest degree possible 
after considering the spectrum of available technologies and the costs 
and benefits associated with those technologies.'' Considering costs 
and benefits associated with control technologies is essentially 
synonymous with the cost per increment of HAP removed, viz. cost 
effectiveness.\47\
---------------------------------------------------------------------------

    \47\ See also, Bluewater Network v. EPA, 370 F.3d 1, 20 (D.C. 
Cir. 2004) (``We agree that EPA may rely on cost and other statutory 
factors to set standards at a level less stringent than that 
reflected by across-the-fleet implementation of advanced 
technologies. This court noted in Husqvarna that `the overriding 
goal of [section 213] is air quality and the other listed 
considerations, while significant, are subordinate to that goal.' 
254 F.3d at 200. Nevertheless, as the court emphasized in reflecting 
on very similar language in section 202(l) of the CAA, the provision 
`does not resolve how the Administrator should weigh all [the 
statutory] factors in the process of finding the greatest emission 
reduction achievable.' Sierra Club v. EPA, 355 U.S. App. D.C. 474, 
325 F.3d 374, 378 (D.C. Cir. 2003)''.
---------------------------------------------------------------------------

    The comment also mischaracterizes the proposed beyond-the-floor 
methodology. The commenter essentially states that EPA's proposed 
beyond-the-floor analyses may not reflect the ``maximum'' degree of HAP 
reduction that is achievable by a given beyond-the-floor control 
technology or method. This is simply not the case. As proposed in the 
reconsideration notice, the beyond-the-floor control options are based 
on what we consider a reasonable assumption of a given control method's 
consistent performance given the levels achieved at the floor. 
Therefore, for each HAP, this performance estimate does indeed reflect 
the maximum degree of reduction that is achievable. Using total 
chlorine as an example, when evaluating beyond-the-floor standards 
based on duct injection dry scrubbing for lightweight aggregate kilns 
and solid fuel boilers, we assumed an incremental control level of 75% 
(from levels achieved at the floor).\48\ We then evaluated the cost 
impacts per ton of total chlorine emission reduction, and the adverse 
energy and solid waste impacts, but only at the control level of 75%. 
That is, we did not evaluate the costs and corresponding emission 
reductions of a given control method--in this example duct injection 
dry scrubbing--for less stringent beyond-the-floor standards (e.g., 
less efficient control levels of 70%, 60%, 50%, etc. for duct injection 
dry scrubbing) and then select the most cost efficient of the various 
control levels evaluated. Thus, the beyond-the-floor analyses presented 
in the reconsideration proposed rule do correspond to a ``maximum'' 
degree of HAP reduction.
---------------------------------------------------------------------------

    \48\ See USEPA, ``Draft Technical Support Document for HWC MACT 
Standards: Reconsideration of the Beyond-the-Floor Evaluations,'' 
July 2006, Section 3, page 3-2.
---------------------------------------------------------------------------

    Comment: The same commenter states, contrary to EPA's claim, that 
Husqvarna AB v. EPA, 254 F.3d 195, 200 (D.C. Cir. 2001) does not 
support EPA's interpretation of section 112(d)(2). According to the 
commenter, although EPA apparently based its cost analysis on cost-
effectiveness in Husqvarna, its decision to do so was neither 
challenged nor at issue in that case, and Husqvarna does not endorse 
it.
    Response: The commenter's reading of Husqvarna is not correct. The 
case both holds that language substantially identical to that in 
section 112(d)(2) ``does not mandate a specific method of cost 
analysis,'' and explicitly upholds the cost-effectiveness method for 
assessing costs used in the rule, since it upheld ``the EPA's choice to 
consider costs on the per ton of emissions removed basis.'' 254 F.3d at 
200. The court also rejected arguments that EPA was required to conduct 
incremental cost-effectiveness analyses (justifying each successive 
increment of control as cost effective), Id., surely an unnecessary 
step if the Agency could not lawfully conduct any type of cost 
effectiveness analysis at all as a means of ascertaining if a standard 
is achievable considering costs.
    Comment: The same commenter further states that EPA's proposed 
method for determining cost-effectiveness for multiple HAP that are 
controlled by a single control mechanism is arbitrary and unrelated to 
any relevant inquiry under the CAA. The commenter notes several 
deficiencies, including: (1) The proposed beyond-the-floor methodology 
is arbitrary because EPA did not explain how the cost of a single 
control device (e.g., an activated carbon injection system) is 
apportioned among the different HAP controlled by it in the 
comprehensive analysis; (2) EPA assigned inappropriately the entire 
cost of a single control mechanism to each different HAP controlled by 
it that yielded false information and a meaningless analysis; and (3) 
EPA failed to assess the cost of a control method against all of the 
HAP controlled by it.
    Response: We disagree with all the points raised in the comment as 
explained below. With respect to the first point made by the commenter, 
the technical support document supporting the reconsideration notice 
explained how the cost of a single control device was apportioned among 
the HAP controlled by it in the comprehensive analysis. The data used 
in the beyond-the-floor cost calculations and the cost apportioning 
results were also included in the appendices of the technical support 
document. Simply stated, the costs of a beyond-the-floor control 
technology or technique is apportioned among the HAP that it would 
control according to the formula shown in the technical support 
document.\49\
---------------------------------------------------------------------------

    \49\ USEPA, ``Draft Technical Support Document for HWC MACT 
Standards: Reconsideration of the Beyond-the-Floor Evaluations,'' 
July 2006, Section 3.1.3. We note that the formula to apportion 
beyond-the-floor costs is shown in Section 3.1.3, paragraph (b), on 
pages 3-4 and 3-5.
---------------------------------------------------------------------------

    For purposes of responding to the comment that EPA's proposed 
beyond-the-floor methodology requires beyond-the-floor controls to be 
purchased and installed more than once (thus overestimating total 
control costs), the following example illustrates why the methodology 
does not do what the commenter suggests. This example shows how the 
beyond-the-floor costs are apportioned using the detailed information 
presented at proposal in Appendix A of the technical support 
document.\50\ Source no. 487 is an

[[Page 64082]]

incinerator that would need reductions in emissions of dioxin/furans, 
mercury, particulate matter, and semivolatile metals in order to 
achieve the suite of beyond-the-floor standards (page 13 of 37 in 
Appendix A) in the comprehensive analysis. Emission reductions of 
dioxin/furans and mercury would be achieved by a new activated carbon 
injection system and improvements to the existing fabric filter, while 
reductions in particulate matter and semivolatile metals would be 
achieved by the same improvements to the existing fabric filter (Id.). 
Thus, costs associated with the activated carbon system are apportioned 
between dioxin/furans and mercury, while the costs of the fabric filter 
improvements are allocated among all four HAP. We estimated the 
combined total annualized costs of one activated carbon injection 
system and the fabric filter improvements for source 487 to be 
approximately $396,000 (Id.). In the comprehensive beyond-the-floor 
analysis, the costs were allocated according to the discussion in 
section 3.1.3 of the technical support document. The results of the 
proposed analysis show that $178,000 was allocated each to dioxin/furan 
and mercury and the remaining $40,000 was allocated equally to 
particulate matter and semivolatile metals (page 27 of 37 in Appendix 
A). The sum of these allocated costs equals the total cost of the new 
activated carbon injection system and fabric filter improvements--
$396,000 ($178,000 + $178,000 + $40,000). Thus, as this example shows, 
we disagree with the commenter that the comprehensive beyond-the-floor 
analysis inflates control costs by requiring beyond-the-floor costs to 
be purchased and installed more than once.\51\
---------------------------------------------------------------------------

    \50\ USEPA, ``Draft Technical Support Document for HWC MACT 
Standards: Reconsideration of the Beyond-the-Floor Evaluations,'' 
July 2006. All page references related to this discussion are from 
this document.
    \51\ This example remains valid as an illustration, although EPA 
has determined for independent reasons not to defend the standards 
for some of the HAP given in the example.
---------------------------------------------------------------------------

    We further disagree with the commenter that our approach to 
apportion control costs is inherently arbitrary and unrelated to any 
relevant inquiry under the CAA. Apportioning control costs in the 
context of the comprehensive analysis allows us to evaluate the costs 
in relation to the HAP controlled. This is particularly true in the 
hazardous waste combustor NESHAP because numerous emission standards 
are established, including standards for dioxin/furans, mercury, 
semivolatile and low volatile metals, particulate matter, hydrogen 
chloride and chlorine, hydrocarbons and carbon monoxide.\52\ The 
allocation approach allows us to evaluate the costs associated with a 
specific HAP and compare it to costs that we have accepted (or 
rejected) in other EPA air programs. Otherwise, given the extensive use 
of standards for individual HAP, such comparisons are difficult. 
Moreover, we are willing to assume higher costs for particularly toxic 
HAP and apportioning control method costs among the similarly 
controlled HAP helps us identify such cases. For example, consider the 
following two theoretical beyond-the-floor situations for a control 
method that achieves a total combined reduction of 100 tons of total 
chlorine and mercury at a cost of $1,000,000. Assume under the first 
scenario that the emission reductions would be split at 99.99 tons of 
total chlorine and 0.01 tons of mercury. Under the second scenario, 100 
tons of total chlorine and mercury would also be reduced, but assume 
the emissions split is 90 tons of total chlorine and 10 tons mercury. 
While the overall cost and total reduction in emissions are constant 
between the two scenarios and may not be warranted as a beyond-the-
floor control option, we may find the reductions for mercury under the 
second scenario as justified, given the greater reductions achieved for 
mercury, and given that mercury is a persistent bioaccumulative toxic 
compound.\53\
---------------------------------------------------------------------------

    \52\ For example, as explained in an earlier footnote, we 
rejected as unachievable the costs associated with adopting beyond-
the-floor standards for all HAP for solid fuel boilers. However, our 
cost allocation procedure showed us that the particulate matter 
standard was achievable even though beyond-the-floor standards for 
the remaining HAP were not.
    \53\ See also 64 FR at 52882 and 52897 (September 30, 1999), 
where EPA accepted a higher cost-effectiveness for semivolatile 
metal reductions for cement and lightweight aggregate kilns to 
ensure that these sources are using the best controls for HAP 
introduced almost exclusively from the burning of hazardous waste.
---------------------------------------------------------------------------

    Finally, the commenter states that EPA failed to assess the cost of 
a control method against all the HAP controlled by it. We disagree. The 
table below, summarizing information in the record at the time we 
issued the reconsideration notice, presents the comprehensive beyond-
the-floor analysis for each source category.\54\ The summary table 
below shows the total annualized control costs and associated emission 
reductions for the beyond-the-floor option for all HAP and HAP 
surrogates.\55\
---------------------------------------------------------------------------

    \54\ USEPA, ``Draft Technical Support Document for HWC MACT 
Standards: Reconsideration of the Beyond-the-Floor Evaluations,'' 
July 2006, Section 3.1.3, Table 4-4, and Appendix A. The examples in 
the text are to illustrate the reasonableness of the general 
methodology for making beyond-the-floor determinations. EPA has 
determined, for independent reasons, not to defend certain of the 
standards included in the above Table.
    \55\ The PM standard is used as a surrogate to control: (1) 
Emissions of nonenumerated metals (antimony, cobalt, manganese, 
nickel, and selenium) that are attributable to all feedstreams (both 
hazardous waste and remaining inputs); and (2) all nonmercury metal 
HAP emissions (both enumerated and nonenumerated metal HAP) from the 
nonhazardous waste process feeds at cement kilns, lightweight 
aggregate kilns, and liquid fuel boilers (e.g., emissions 
attributable to coal and raw material at a cement kiln, and 
emissions attributable to fuel oil for liquid fuel boilers).

               Table 1--Summary of Comprehensive Beyond-the-Floor (BTF) Analysis in Proposed Rule
----------------------------------------------------------------------------------------------------------------
                                              Total                 Emission reductions of BTF option
                                           annualized   --------------------------------------------------------
            Source category                cost of BTF      Total all HAP and HAP      Reductions by HAP and HAP
                                             option               surrogates                   surrogate
----------------------------------------------------------------------------------------------------------------
Incinerators...........................     $20,200,000  140 t......................  D/F: 0.8 g; PM: 46 t; Hg:
                                                                                       0.2 t; SVM: 0.4 t; LVM:
                                                                                       0.2 t; TCl: 91 t; organic
                                                                                       HAP: 2.4 t.
Cement kilns...........................      27,800,000  499 t......................  D/F: 1.4 g; PM: 322 t; Hg:
                                                                                       0.7 t; SVM: 1.3 t; LVM:
                                                                                       0.06 t; TCl: 141 t;
                                                                                       organic HAP: 33 t.
Lightweight aggregate kilns............       4,200,000  279 t......................  D/F: 1.1 g; PM: 9.1 t; Hg:
                                                                                       0.02 t; SVM: 0.02 t; LVM:
                                                                                       0.01 t; TCl: 270 t;
                                                                                       organic HAP: 0.2 t.
Liquid fuel boilers....................      24,400,000  679 t......................  D/F: 0.4 g; PM: 437 t; Hg:
                                                                                       0.06 t; SVM: 0.1 t; LVM:
                                                                                       1.1 t; TCl: 241 t;
                                                                                       organic HAP: 0.1 t.
Solid fuel boilers.....................       8,800,000  1,264 t....................  D/F: 0.3 g; PM: 468 t; Hg:
                                                                                       0.03 t; SVM: 0.5 t; LVM:
                                                                                       0.5 t; TCl: 794 t;
                                                                                       organic HAP: 1.0 t.

[[Page 64083]]


Hydrochloric production furnaces.......         904,000  17 t.......................  D/F: 0.1 g; TCl: 17 t;
                                                                                       organic HAP: 0.01 t.
----------------------------------------------------------------------------------------------------------------

    Comment: The same commenter states that EPA proposed a flawed 
beyond-the-floor analysis with respect to organic HAP (other than 
dioxin/furans) that would be controlled by activated carbon injection. 
According to the commenter, carbon monoxide and hydrocarbons are not 
valid surrogates for non-dioxin/furan organic HAP, in general, and are 
irrational as a basis for evaluating the cost-effectiveness of 
activated carbon injection for the organic HAP that it controls because 
EPA did not propose a cost-effectiveness of the control measure. As a 
result, the proposed beyond-the-floor analysis overstated costs and 
understated effectiveness.
    Response: To the extent the commenter is suggesting that carbon 
monoxide and hydrocarbons are generally poor surrogates for organic 
HAP, we strongly disagree. We have fully explained in earlier rules our 
rationale of using these organic HAP surrogates when establishing MACT 
floor standards for hazardous waste combustors. 64 FR at 52847-52. 
Furthermore, the beyond-the-floor analysis of control methods for 
organic HAP that do not control other HAP regulated by this rule ( 
e.g., use of an afterburner or use of better combustion practices to 
reduce organic HAP emissions) are not at issue in this proceeding.
    As stated in the reconsideration notice, we indicated that it was 
inappropriate to identify numerical beyond-the-floor standards for 
carbon monoxide and hydrocarbons based on activated carbon injection. 
71 FR at 52636. We continue to believe this decision is sound for the 
reasons discussed in the proposed rule. However, in response to 
comments, we have examined the activated carbon injection beyond-the-
floor analysis discussed in the reconsideration notice. In the proposed 
rule we estimated total annualized costs and emission reductions of 
dioxin/furans, mercury, and organic HAP associated with activated 
carbon injection.\56\ Aggregating the costs and emission reductions for 
the three HAP, the cost-effectiveness of the activated carbon injection 
option can be estimated for each source category. For each source 
category, the cost-effectiveness results were considered unreasonable, 
within the meaning of section 112(d)(2). For example, the cement kiln 
standards were found to be most cost-effective at approximately 
$560,000 per ton of organic HAP, mercury, and dioxin/furan removed. 
Given that 98% of the 34 tpy of HAP reduced under the activated carbon 
injection option are organic HAP, we find that this cost-effectiveness 
value exceeds estimates previously rejected by EPA for organic HAP 
control for non-hazardous waste cement kilns. 71 FR at 76531.
---------------------------------------------------------------------------

    \56\ USEPA, ``Draft Technical Support Document for HWC MACT 
Standards: Reconsideration of the Beyond-the-Floor Evaluations,'' 
July 2006, page 4-6, Appendix A, pages 2 and 4.
---------------------------------------------------------------------------

    Comment: One commenter states that some of the emission standards 
promulgated in the October 12, 2005 final rule already represent 
beyond-the-floor standards because EPA has not shown that 12% of 
existing sources can achieve the standards without modification. Thus, 
the commenter states that the beyond-the-floor analyses are moot until 
EPA justifies the existing standards as beyond-the-floor standards.
    Response: We disagree with the commenter. The MACT floor standards 
are based on the performance of actual sources within each source 
category. That is, we did not base MACT floors on theoretical sources. 
Given that the control methods needed to achieve the MACT floor 
standards are fully integrable and compatible, we are not obligated to 
establish a suite of floor standards that are simultaneously achievable 
by at least six percent of the sources because the standards are not 
technically interdependent. See Chemical Manufacturers Ass'n, 870 F. 2d 
at 239 (best performing sources can be determined on a pollutant-by-
pollutant basis so that different plants can be best performers for 
different pollutants).
    Comment: One commenter suggests that EPA better explain how costs 
were allocated among multiple HAP in the comprehensive analysis and why 
the chosen method is reasonable and appropriate.
    Response: In finalizing the technical support document, we have 
expanded the discussion as suggested by the commenter. See ``Technical 
Support Document for HWC MACT Standards: Petitions for Reconsideration 
Support Document,'' October 2008.

G. Dioxin/Furan Standard for Incinerators With Dry Air Pollution 
Control Devices

    The petition of the Sierra Club sought reconsideration of the 
dioxin/furan standard for existing incinerators with either a dry air 
pollution control device or waste heat boiler.\57\ In the October 12, 
2005 final rule, we promulgated a dioxin/furan standard of 0.40 ng TEQ/
dscm provided that the combustion gas temperature at the inlet to the 
initial particulate matter control device is 400 [deg]F or below (see 
Sec.  63.1219(a)(1)(i)). The final standard for this subcategory was 
less stringent than that proposed (0.28 ng TEQ/dscm) as a result of a 
data base change between proposal and promulgation. 71 FR at 52636-638. 
We made this data base change, which pertained to incinerator source 
327 (specifically, test condition C10) in our data base, in response to 
public comments to the proposed rule. 70 FR at 59432. In its petition 
for reconsideration, the Sierra Club stated that the dioxin/furan floor 
standard increased as a result of EPA's post proposal decision to use 
different data to represent source 327 and that EPA had provided no 
opportunity for public comment on this data handling decision. Pursuant 
to section 307(d)(7)(B) of the CAA, we granted the Sierra Club's 
petition for reconsideration of the dioxin/furan standard for 
incinerators with either a dry air pollution control device or waste 
heat boiler.
---------------------------------------------------------------------------

    \57\ The Sierra Club also petitioned EPA to reconsider the 
dioxin/furan standard for the subcategory of incinerators with wet 
or no air pollution control devices. As discussed in the September 
6, 2006 notice, we denied this reconsideration request (71 FR at 
52627). See also docket item EPA-HQ-OAR-2004-0022-0558.
---------------------------------------------------------------------------

    As stated in the September 6, 2006 reconsideration notice, the 
arguments provided by the Sierra Club in its petition for 
reconsideration did not convince us that our decision on what emissions 
data to use to represent source 327 for the dioxin/furan MACT

[[Page 64084]]

floor analysis was erroneous or inappropriate. Therefore, in the 
reconsideration notice we solicited comment on the identical MACT floor 
analysis (for dioxin/furans for this incinerator subcategory) and 
underlying data handling decision regarding source 327 as promulgated 
in the October 12, 2005 final rule. 71 FR at 52636-38. That is, we 
proposed not to use the dioxin/furan test results where source 327 
encountered operational problems with its carbon injection system. 
Instead, we proposed to use other valid emissions data in our emissions 
data base from this source in the MACT floor analysis. In response to 
the notice for reconsideration, we received five comment letters on 
this issue. These comment letters are available in the official public 
docket.\58\
---------------------------------------------------------------------------

    \58\ See comments 0563, 0565, 0567, 0568, and 0569 in the docket 
(EPA-HQ-OAR-2004-0022).
---------------------------------------------------------------------------

1. Summary of the Final Action
    The comments to the reconsideration notice provided limited new 
information regarding the dioxin/furan standard for incinerators with 
either a dry air pollution control device or waste heat boiler. No new 
technical information on the dioxin/furan test results that EPA 
excluded were received in comments. We received one comment letter that 
challenged whether we exercised appropriate judgment in excluding the 
one test result from source 327. After evaluation of the comments, we 
are deciding to retain the dioxin/furan standard as promulgated and are 
making no changes to the final rule. Because we are not revising the 
dioxin/furan standard for incinerators, the standard as promulgated 
under Sec.  63.1219(a)(1) remains unchanged.
2. What Are the Responses to Major Comments?
    We received five comment letters in support of and one comment 
letter objecting to our decision to replace the 2001 data for source 
no. 327 with other dioxin/furan emissions data in our data base. A 
summary of major comments received on this reconsideration issue and 
EPA's responses to those comments are provided below.
    Comment: A comment was received stating that EPA did not explain 
why the MACT floor standard was based exclusively on compliance test 
data. The same commenter argues that the 2001 test results from source 
327 (i.e., the test data during which operational problems with the 
carbon injection system occurred) were conducted under compliance test 
conditions and should be characterized as such in EPA's data base. 
Finally, the commenter states that whether or not the test results for 
source 327 were used to establish operating parameter limits is not 
relevant in determining whether they are compliance test data.
    Response: We disagree with the comment. As explained in the 
September 6, 2006 reconsideration notice, we solicited comment on the 
identical MACT floor analysis and standard that was promulgated for 
this subcategory of incinerators. 71 FR at 52636-38. As explained in 
the proposed rule, EPA's data base is comprised of emissions data from 
tests conducted for various reasons. For MACT floor analysis purposes, 
all emissions data were characterized in one of four ways: ``compliance 
test'' data, ``normal'' data, ``in-between'' data, and ``not 
applicable'' data. See 69 FR at 21218-219 (April 20, 2004). After 
characterizing the data, we followed a general ``data hierarchy'' to 
identify the data to use for each emissions standard. 69 FR at 21229. 
For the subcategory of existing incinerators with either a dry air 
pollution control device or waste heat boiler, we tentatively concluded 
at proposal and confirmed in the 2005 final rule that it is appropriate 
to base the dioxin/furan standard on ``compliance test'' emissions data 
associated with the most recent test campaign. See 69 FR at 21240 
(April 20, 2004) and page 10-4 of ``Technical Support Document for HWC 
MACT Standards, Volume III: Selection of MACT Standards'' (September 
2005). Therefore, the record clearly shows our consistent intent to use 
compliance test data to determine the MACT floor standard for this 
subcategory of incinerators, as the data most representative of the 
performance of sources in this subcategory.
    In response to public comments to the April 20, 2004 proposed rule, 
the characterization of source 327's test data (i.e., test condition 
327C10 in our data base) was changed from ``compliance test'' to ``not 
applicable'' because the carbon injection system malfunctioned during 
the test. As discussed in the technical support document, one of the 
reasons data may be characterized as ``not applicable'' is if problems 
were encountered during testing that ``prevented the data from being 
used for regulatory compliance purposes.'' The operational troubles 
experienced during testing prevented source 327 from using the data in 
question to set operating parameter limits, a regulatory compliance 
purpose. See ``Draft Technical Support Document for HWC MACT Standards, 
Volume II: HWC Data Base'' (March 2004), pages 2-3 to 2-6, and 
``Technical Support Document for HWC MACT Standards, Volume II: HWC 
Data Base'' (September 2005), pages 2-11 to 2-13. If the data are 
unsuitable for regulatory purposes (which is unquestioned here), then 
EPA can reasonably decline to use the data to characterize the source's 
performance for standard setting purposes.
    Comment: One commenter states that our decision not to use the 2001 
test data from source 327 and instead use dioxin/furan emissions data 
with higher levels from 1992 is arbitrary and capricious. This is 
because EPA had no reason to believe that source 327 would perform 
worse than the level it achieved despite operational problems.
    Response: The 2001 test data in our data base for source 327 do not 
represent the source's performance over time because the source 
encountered operational problems during testing. As a result, we 
believe it is inappropriate to use such data when identifying MACT 
floor standards (or any other standards, for that matter). The fact 
remains that we have no valid data reflecting the performance and 
performance variability of this source when using a carbon injection 
system. While dioxin/furan emission results may be lower using the 
carbon injection system, we are not in possession of such data. It is 
also a fact that none of the available 1992 emissions data (i.e., the 
only compliance test data in our data base for this source) is low 
enough to be considered among the 12 percent of best performers. As a 
result, available valid emissions data for source 327 have no direct 
impact on the MACT floor analysis.
    Comment: One commenter stated that the dioxin/furan standard is 
unlawful and arbitrary and capricious because the calculated MACT floor 
of 0.42 ng TEQ/dscm is less stringent than the current interim standard 
of 0.40 ng TEQ/dscm. Therefore, these results indicate that the MACT 
floor methodology does not yield floors reflecting the actual 
performance of the relevant best sources.
    Response: We disagree with the comment for the same reasons 
discussed in Part Four, Section III.F of the October 12, 2005 final 
rule. 70 FR at 59458.

H. Provisions of the Health-Based Compliance Alternative

    The October 12, 2005 final rule allowed sources to establish and 
comply with health-based compliance alternatives for total chlorine for 
hazardous waste combustors other than hydrochloric acid production 
furnaces in lieu of the MACT technology-based emission standards 
established under Sec. Sec.  63.1216, 63.1217, 63.1219, 63.1220,

[[Page 64085]]

and 63.1221. See 70 FR at 59413-19 and Sec.  63.1215.
    Sierra Club petitioned for reconsideration stating that EPA changed 
several provisions of the health-based compliance alternative after the 
period for public comment and therefore did not provide notice and 
opportunity for public comment.\59\ In addition, Sierra Club stated 
that three new provisions are problematic: (1) It is unlawful to allow 
sources to comply with the health-based compliance alternative without 
prior approval from the permitting authority; (2) it is unlawful to 
allow a source to obtain an unlimited extension of the compliance date 
if their eligibility demonstration is disapproved and the source is 
unable to change the design or operation of the source to comply with 
the MACT emission standards by the compliance date; and (3) the Agency 
cannot rely on the Title V program as the vehicle for establishing 
health-based compliance alternatives.
---------------------------------------------------------------------------

    \59\ See letter from James Pew to Stephen Johnson, dated 
December 12, 2005, Section XII, docket item EPA-HQ-OAR-2004-0022-
0517.
---------------------------------------------------------------------------

    We granted reconsideration of these provisions because we developed 
them in response to comments on the proposed rule, after the period for 
public comment as Sierra Club stated. Furthermore, to address Sierra 
Club's concerns, we proposed to revise the rule pertaining to these 
provisions as follows: (1) The rule would state that the operating 
requirements specified in the eligibility demonstration are 
``applicable requirements'' as defined in 40 CFR 70.2 or 71.2 and 
therefore must be incorporated in the Title V permit; (2) a source may 
comply with the health-based compliance alternative without prior 
approval from the permitting authority provided that the source has 
made a good faith effort to provide complete and accurate information 
and to respond to any requests for additional information; and (3) the 
compliance date extension cannot exceed one year if the eligibility 
demonstration is disapproved and the source is unable to change the 
design or operation to comply with the MACT emission standards by the 
compliance date.
1. Summary of the Final Action
    We are today promulgating revisions to the health-based compliance 
alternative as proposed in the reconsideration notice. The comments to 
the reconsideration notice did not provide a basis for us to conclude 
that the health-based compliance alternative, as we proposed to revise 
it, was inappropriate. Therefore, we reaffirm the health-based 
compliance alternative that we promulgated in the October 12, 2005 
final rule, as revised today subsequent to the reconsideration notice.
    Please note that the revised provisions are effective immediately, 
and today's final rule does not change the October 14, 2008 compliance 
date established by the October 12, 2005 final rule. Sources can 
readily comply with the revised provisions promulgated today on the 
compliance time line established by the October 12, 2005 final rule.
2. What Are the Responses to Major Comments?
    Comment: Sierra Club states that the health-based compliance 
alternatives are implemented through Title V permits, and because Title 
V permits expire, this is evidence that the health-based alternatives 
are not emission standards within the meaning of CAA section 112(d)(4).
    Response: In the reconsideration notice, we explained that, because 
the health-based compliance alternative requirements are clearly 
defined (e.g., HCl-equivalent emission limits, chlorine feedrate 
limits), and because any standards or requirements created under CAA 
section 112 are considered ``applicable requirements'' under 40 CFR 
part 70, the compliance alternatives would be incorporated into Title V 
permits.\60\ 70 FR at 59481; 71 FR at 52639.
---------------------------------------------------------------------------

    \60\ Applicable requirements defined under Sec.  70.2 must be 
included in Title V permit, as required under Sec.  70.6(a)(1).
---------------------------------------------------------------------------

    Nonetheless, in response to Sierra Club's reconsideration petition 
that the Agency cannot rely on the Title V program as the vehicle for 
establishing health-based compliance alternatives we proposed to revise 
the rule to add clarifying regulatory language stating that Sec.  
63.1215 requirements are applicable requirements under part 70 and 
therefore must be included in the Title V permit as would any other 
applicable requirement.
    We are promulgating that requirement today (see Sec.  
63.1215(e)(3)) and disagree with the commenter's view that the health-
based alternatives are implemented through the Title V permit rather 
than established as a national standard by rule. The rule itself 
establishes not only the standard's level of protection, which is 
uniform nationwide and assures that emissions of total chlorine from 
each source complying with the alternative standard will be less than 
the threshold level for total chlorine with an ample margin of 
safety,\61\ but also establishes each and every step that sources must 
use to calculate that standard. The permit writer ascertains that the 
source has applied the rule properly (e.g., has not put incorrect 
factual inputs into the equations and formulae provided in the rule). 
Thus, the rule not only establishes the level of control (which is 
uniform nationally, as just stated) but the exclusive means of 
developing the emission limit which satisfies that level. Moreover, 
sources must establish a numerical limit (using the exclusive protocols 
set out in the rule) before permitting. This limit is immediately 
enforceable against the source. The permitting process determines if 
this limit was determined correctly (i.e. whether the source applied 
the protocols in the rule correctly). See Sec.  63.1215(e) and (g).
---------------------------------------------------------------------------

    \61\ Specifically, that exposure to the actual individual most 
exposed to the facility's emissions, considering off-site locations 
where people congregate for work, school, or recreation, is less 
than that level. See Sec.  63.1215(c)(ii).
---------------------------------------------------------------------------

    The situation is analogous to the way parametric monitoring limits 
implementing numeric section 112(d)(2) standards are established: a 
national rule establishes a numerical standard and specifies which 
parameters are to be monitored; a source determines the actual levels 
of those parameters based on site-specific conditions and establishes 
enforceable parametric monitoring limits for itself; and a permit 
writer decides whether to ratify the source's determination and 
memorializes the quantified parametric monitoring limit in the source's 
permit. Id. There is no suggestion that this process violates the 
requirement that EPA establish national emission standards.
    Comment: Sierra Club states that allowing sources to comply with 
the health-based compliance alternatives without prior approval from 
the permitting authority further confirms that the alternatives are not 
standards at all, and violates the CAA by allowing sources to operate 
without any assurance that HAP emissions are controlled.
    Response: The comment is confusing, since MACT standards are 
implemented in advance of permitting (as are the alternative section 
112(d)(4) standards), and are, of course, emission standards. Further, 
the health-based compliance alternative is a requirement established by 
EPA ``which limits the quantity, rate, or concentration of emissions of 
air pollutants on a continuous basis,'' and so is an ``emission 
standard'' under section 302(k) of the Act (which definition applies to 
section 112(d)).

[[Page 64086]]

The section 112(d)(4) standard is an emission concentration limit 
(ppmv) for total chlorine that is demonstrated not to result in a 
Hazard Index \62\ for hydrogen chloride and chlorine gas exceeding 1.0.
---------------------------------------------------------------------------

    \62\ The Hazard Index is the sum of the Hazard Quotients for 
hydrogen chloride and chlorine gas. The Hazard Quotient (HQ) is the 
ratio of the predicted ambient air concentration of a pollutant to 
the air concentration at which no adverse effects are expected. For 
chronic inhalation exposures, the HQ is calculated as the air 
concentration divided by the reference concentration (RfC). For 
acute inhalation exposures, the HQ is calculated as the air 
concentration divided by the acute reference exposure level (aREL).
---------------------------------------------------------------------------

    Comment: Sierra Club states that EPA's ``individualized source-by-
source loophole program'' does not provide emission standards. The 
comment continues that since section 112(d) standards must be 
established on a category or subcategory basis, the most a section 
112(d)(4) standard can lawfully do is require all sources to emit at 
the uniform limit which will not result in adverse effects to human 
health with an ample margin of safety. The commenter continues that to 
satisfy section 112(d)(4), that standard must moreover account for the 
individual circumstances of each emitting source (including receptor 
location).
    Response: The standards adopted in the rule apply on a categorical 
basis and assure that each source in the category adopting this 
alternative emits total chlorine at a level which is protective of 
human health with an ample margin of safety. The level of protection 
afforded is identical in each instance the compliance alternative is 
satisfied: exposure to less than the hazard index for total chlorine 
(which hazard index reflects an ample margin of safety), and hence 
exposure to less than the threshold level of effect for total chlorine. 
Individual circumstances of each emitting source (such as dispersion 
characteristics and the location of most-exposed receptor) must be 
accounted for in demonstrating that the source is eligible for the 
alternative standard (just as actual parametric monitoring limits 
implementing numeric limits are established post-rule to account for 
individual circumstances). See Sec.  63.1215(c)(2) which requires that 
the demonstration of eligibility show that emissions of total chlorine 
(measured as HCl equivalence) be shown to be less than the Hazard Index 
for chronic exposure ``for the actual individual most exposed to the 
facility's emissions, considering off-site locations where people 
reside and where people congregate for work, school, or recreation''; 
see also Sec.  63.1215(c)(3)(v) requiring the demonstration to account 
for emissions from all emitting hazardous waste combustors at a site. 
As explained in the previous response, this provision thus satisfies 
the statutory definition of ``emission standard,'' as well as all 
applicable section 112(d) requirements.
    Comment: Sierra Club states, without analysis, that the provision 
violates RCRA as well as the Clean Air Act, because the standards are 
insufficient to protect public health and the environment.
    Response: EPA showed in promulgating the provision that emissions 
would be protective of human health and the environment (70 FR at 
59479-80), and commenter has not provided information to the contrary.
    Comment: The commenter cites legislative history to the 1990 
amendments (1 Legislative History at 866) in which Congress rejected a 
provision which would have allowed individual sources to waive out of 
MACT requirements by demonstrating that their HAP emissions pose 
negligible risk to public health. The commenter views this history as 
supporting its argument since it regards the provision here as 
analogous.
    Response: EPA does not believe the provision discussed in the 
legislative history is analogous. It would have allowed a demonstration 
of low risk for all toxics, not just threshold pollutants. Section 
112(d)(4) is limited in scope to threshold pollutants where the 
Administrator has identified a level that protects public health with 
an ample margin of safety. EPA's rule here reasonably implements that 
authority.
    Comment: Sierra Club states that it is impermissible and further 
indication that the health-based compliance alternatives are not 
emission standards to allow an automatic extension of the compliance 
date upon disapproval of an eligibility demonstration to allow the 
source time to make changes to the design or operation of the combustor 
or related systems as quickly as practicable to enable the source to 
achieve compliance with the total chlorine MACT standards. Sources must 
comply with MACT standards within no more than three years, absent an 
individualized demonstration of a need for further time to install 
controls.
    Response: We disagree with the characterization that the time 
extension is automatic. Section 63.1215(e)(2)(i)(B) states that the 
permitting authority may extend the compliance date by up to one year 
(as revised by today's rule) to allow the source to make changes to the 
design or operation of the combustor to achieve compliance with the 
MACT total chlorine standards. An individualized showing is required to 
support such an extension. In addition, an extension would be granted 
only for the time needed (but not exceeding one year) to make the 
changes required to achieve compliance with the emission standards. 
That is expressly the purpose of the time extension provision of CAA 
section 112(i)(3)(B), which allows extensions of a section 112(d) 
standard's effective date for up to one year where necessary for the 
installation of controls.
    Comment: Sierra Club states that EPA lacks authority to grant 
source-by-source exemptions from Section 112 emission standards.
    Response: We agree. The health-based compliance alternatives are 
section 112 emission standards, as we have explained in this preamble 
and in the October 12, 2005 final rule. See 70 FR at 59479. Thus, no 
sources are exempted from such standards.

IV. Response to Comments to the September 27, 2007 Notice

    On September 27, 2007, EPA issued a notice for public comment which 
discussed the standards that EPA promulgated in October 2005, and 
specifically identified which standards EPA believes are consistent 
with the Act and caselaw, and which standards are not and need to be 
reexamined through a subsequent rulemaking. 72 FR 54875. With respect 
to those standards EPA announced it intended to defend, the notice 
indicated the portions of the rationale upon which EPA intended to 
rely, and which portions EPA would no longer rely upon as a 
justification for the standards. EPA sought public comment on this 
analysis and placed edited versions of various support documents in the 
public docket, edited to remove portions of the rationale on which EPA 
no longer planned to rely, and solicited public comment on these edits.
    After receipt of public comment, EPA has further narrowed the 
number of standards it intends to defend. We respond here to the 
principal public comments with respect to those standards which EPA has 
announced its intention to defend. However, as an initial matter, one 
commenter argued that EPA may not amend portions of the record or 
revise rationales for the final rule without proposing to amend the 
rule, i.e., recommencing rulemaking procedures. EPA disagrees. The 
Clean Air Act provides that EPA may reconsider rules based on new 
information which arose after the period for public comment. CAA 
section 307(d)(7)(B). The Brick MACT opinion is such a type of new 
information. Sierra Club v. EPA, 479 F.3d 875 (2007) (Brick MACT). 
Also, EPA may decide itself to

[[Page 64087]]

reconsider a rule based on existence of such new information (i.e., 
initiate reconsideration sua sponte). See 72 FR at 76553 (December 20, 
2006). EPA essentially adopted that course here, providing notice and 
opportunity for public comment as required by section 307(d)(7)(B) 
(including a comment period ultimately extended to two months (see 72 
FR 59067 (October 18, 2007). However, to make explicit that this action 
is part of a reconsideration process, EPA is including its responses to 
comment here as part of the reconsideration process already initiated 
for the Hazardous Waste Combustor MACT rule.\63\ Final edited versions 
of the various support documents are also included in the public 
docket.
---------------------------------------------------------------------------

    \63\ EPA also does not believe any commenters were prejudiced by 
the procedure EPA adopted, since all the commenters had notice of 
EPA's action, and had ample time to submit comments, of which they 
availed themselves. In addition, EPA provided notice to the general 
public by means of publication in the Federal Register so any 
interested person could respond.
---------------------------------------------------------------------------

    With one exception, all commenters to the September 2007 notice 
supported EPA's analysis of the standards and did not suggest any 
changes to that analysis. The one adverse commenter was Earthjustice 
(on behalf of Sierra Club), which submitted extensive comments raising 
various challenges. Earthjustice, however, did not contest EPA's main 
premise: sources which emit more hazardous air pollutant (HAP) over 
time than other sources (e.g., those with lower emissions in single 
tests) do not have to be regarded as best performing, and this holds 
true for those higher-emitting sources which may emit less HAP in a 
single snapshot test. 72 FR at 54877. EPA set out at length in the 
October 2005 rule and the September 2007 notice why it believes it 
identified as best performers sources emitting the lowest amount of HAP 
over time and reasonably estimated their levels of performance. Most of 
the responses below deal with the issue of the reasonableness of this 
analysis.
    Before addressing these specifics, we first address certain general 
points. EPA demonstrated in both the preamble to the final rule and in 
the September notice that the commenter's preferred approach for the 
existing source floor of taking the average of the lowest emitting 
sources in single tests did not properly characterize these sources' 
performance because it ignored their short- and long-term variability 
and thus their performance over time. The commenter now maintains that 
even if this is true, it is irrelevant because EPA must still show that 
the sources the Agency identified as best are in fact best performers. 
Although EPA must of course provide a reasoned explanation justifying 
its selection of best performers and their level of performance, EPA 
believes it is clear on this record that one cannot presume that 
sources with lowest HAP emission in single tests are best performers, 
or presume that single snapshot performance test information is an 
adequate representation of sources' actual performance over either 
short or long time periods. A further consequence, as explained in the 
following paragraph, is that whatever methodology is utilized for 
identifying best performing sources necessarily involves some type of 
estimate as to sources' performance and that the starting point for 
such estimates need not be sources with lowest HAP emissions in single 
tests.
    Earthjustice, however, seizes on EPA's conclusion that sources 
rejected by EPA as best performers ``likely'' perform worse over time, 
calling this unwarranted speculation, and suggests more data-gathering 
to develop a legally mandated quantum of proof (e.g., Earthjustice's 
Comments pp. 1, 2, 8; docket item EPA-HQ-OAR-2004-0022-0613). As the 
commenter is aware, however, no reliable quantification of performance 
over time is now possible (except for particulate matter emissions from 
sources equipped with fabric filters (see 72 FR at 54879)) because 
continuous emission monitors for HAP do not exist, or for HAP for which 
CEMS are just beginning to be implemented for HWCs, there are too few 
data to evaluate sources' performance. Long-term performance of sources 
for HAP therefore are necessarily estimates. EPA's conclusion that 
sources it selected as best performers ``likely'' emit less HAP over 
time is an accurate reflection that definitive proof (i.e., day-in, 
day-out quantified performance) is impossible in the absence of 
continuous emission monitoring results. More data collection would 
yield more snapshot results, so long-term performance would still have 
to be estimated.\64\ However, the record demonstrates that EPA's 
conclusions are not mere speculations, but rather are supported by 
sound evidence and are consequently reasonable. Mossville Environmental 
Action Now v. EPA (Mossville), 370 F. 3d at 1240-41 (D.C. Cir. 2004) 
(summarizing case law that EPA may use estimates to assess performance 
of best-performing sources, and stating further that courts will accept 
these estimates if they have a reasoned basis).
---------------------------------------------------------------------------

    \64\ However, in this rule, EPA has carefully compiled and 
studied data from different tests from lowest emitting sources in 
single tests to best estimate these sources' long-term performance.
---------------------------------------------------------------------------

    Finally, Earthjustice repeats earlier comments that because sources 
maximize operating parameters when they conduct compliance tests in 
order to obtain an ample compliance margin, compliance tests already 
account for total operating variability. However, as explained in the 
rulemaking, compliance tests can only account for controllable 
operating variability, and there are numerous uncontrollable factors 
that result in short- and long-term variability not accounted for in 
compliance tests. 70 FR at 59439 (October 12, 2005). The record shows 
that in virtually every case when comparisons with other test 
conditions are possible, lowest emitters in one compliance test emitted 
more HAP in other tests.\65\ Indeed, in most of the comparisons, the 
sources emitted more than their estimated performance including run-to-
run variability (which we refer to as UPL99).\66\ Id.\ 67\ Another 
example, as discussed above, is the Ash Grove Chanute source, where the 
source in later tests emitted more particulate matter than projected by 
EPA even after adjusting the source's initial test results to account 
for run-to-run and test-to-test variability. This empirical 
demonstration shows that lowest emitting sources in single tests can 
emit more HAP over time, and that the amounts emitted routinely can 
exceed even their estimated short-term variability or total 
variability. Necessarily, the demonstration also shows that the single 
test condition measurements do not fully encompass these sources' 
actual variability. EPA thus correctly concluded that run-to-run and 
test-to-test variability--short-term and long-term variability over and 
beyond performance measured in a single stack test--are real and 
appreciable, and consequently an

[[Page 64088]]

element of sources' performance. See Technical Support Document 
(``TSD'') Vol. III, sections 16.3 to 16.6, 17.2 and 17.3.\68\
---------------------------------------------------------------------------

    \65\ See memorandum from Bob Holloway to docket entitled 
``Analysis of Available Performance Data from Best Performing 
Sources'', September 8, 2008.
    \66\ The UPL99 means the 99th percentile upper prediction limit 
and is an estimate of the value that the source would achieve in 99 
of 100 future tests if it could replicate the operating conditions 
of the compliance test. 70 FR at 59437 (October 12, 2005).
    \67\ The commenter challenged EPA's statements, maintaining that 
these data do not show which sources are the best performers. See, 
e.g. Earthjustice's comments p. 3. EPA developed these data to show 
that the commenter's argument that test conditions already account 
for all of sources' operating variability ``and then some'' 
(Earthjustice's comments p. 4) is demonstrably incorrect, and that 
an approach of averaging snap shot emission tests--even after 
adjusting results to account for run-to-run variability, still does 
not fully account for sources' full operating variability--i.e., 
their performance over time.
    \68\ USEPA, ``Technical Support Document for HWC MACT Standards, 
Volume III: Selection of MACT Standards'', (TSD Vol. III) September 
2005. Unless otherwise specified, all TSD references in this section 
of the notice are to this document, which is available in the docket 
to the rule.
---------------------------------------------------------------------------

A. Standards for Particulate Matter

1. Standards for Incinerators, Cement Kilns, Lightweight Aggregate 
Kilns, and Solid Fuel Boilers
    EPA has carefully reviewed all of its data for particulate matter 
and concluded, with certain exceptions, that the current standards 
require some revision (in some cases due to record correction issues 
rather than to issues related to section 112(d)(3) and the Brick MACT 
opinion).\69\ The exceptions are the new source particulate matter 
standards for incinerators, cement kilns (see also section III.E 
above), and lightweight aggregate kilns, and the particulate matter 
standards for existing and new solid fuel boilers. For these standards, 
EPA believes that it properly assessed which sources are best 
performing and reasonably estimated their level of performance. EPA 
also has previously indicated why more stringent, beyond-the-floor 
standards are or are not achievable for these source categories. See 71 
FR at 14670; TSD Vol. III, sections 10.3.4, 12.3.4, 14.3.2 and 14.3.4.
---------------------------------------------------------------------------

    \69\ With respect to standards for particulate matter for 
incinerators, for example, EPA is concerned that the database 
includes certain types of specialty chemical demilitarization 
operations where metals are not volatilized within the common pool 
of incinerators (see also n. 72 below with respect to high and low 
volatility metals emitted by incinerators). With respect to 
particulate matter emitted by cement kilns, further study of 
operating conditions of one of the sources classified as a best 
performer may require reassessment of that source's performance.
---------------------------------------------------------------------------

2. Standards for Liquid Fuel Boilers
    EPA believes that the particulate matter standard for existing and 
new liquid fuel boilers requires revision for the reasons discussed in 
the September 2007 notice. 72 FR at 54880.

B. Standards for Semivolatile Metals and Low Volatile Metals

1. Standards for Incinerators and Solid Fuel Boilers
    EPA selected as best performers for semivolatile (lead and cadmium, 
or SVM) and low volatile (arsenic, beryllium and chromium, or LVM) HAP 
metals the sources with the best combination of hazardous waste 
feedrate control of the respective metals and best system removal 
efficiency (generally, most efficient emission controls). EPA continues 
to believe that these sources will emit the least SVM and LVM over time 
since they will have the least long-term variability. 72 FR 54880-881. 
Comparative test data support this conclusion. Sources with lower SVM 
and LVM emissions in single tests either have had emissions in historic 
tests that are higher than the emissions of the sources EPA identified 
as best performing, can reasonably be projected to emit more than the 
EPA-identified best performers based on their historic performance 
(historic system removal efficiency applied to amount fed in 
performance test would result in higher emissions than EPA-identified 
best performers),\ 70\ or are simply unrepresentative.\71\
---------------------------------------------------------------------------

    \70\ For example, incinerator source 327, which in a single test 
condition had a UPL99 for SVM which is 25 times less than the 
highest-emitting of the best-performing sources in the MACT pool, 
would emit over three times more SVM than that highest-emitting best 
performer assuming it fed the same amount of metals as in its 
compliance test but removed them from its emissions at the 
efficiency demonstrated in other of its historic compliance tests. 
TSD Vol. III, Table 17.6 and App. E, Table SF-INC-SVM.
    \71\ Certain of the sources (incinerator sources 494 and 3011) 
are specialty operations feeding large chunks of metal contaminated 
with trace organics (e.g., inert materials, bulk explosives, metal 
waste). These metals generally are not emitted because of the large 
particle size of the feed--SVM are not volatilized and LVM are not 
entrained in the combustion gas. These operations are not 
representative of usual incineration, where metals are present in 
the feed as organometallic compounds or metal dispersed in an 
organic or aqueous liquid such that SVM is generally volatilized and 
LVM is generally entrained in the combustion gas. USEPA, ``Technical 
Support Document for HWC MACT Standards, Volume II: HWC Data Base'', 
(TSD Vol. II) September 2005, App. B in data sheet ``inc-svm.xls'', 
App. C in data sheets ``494.xls'' and ``3011.xls''.
---------------------------------------------------------------------------

    Earthjustice states that such comparisons are unwarranted because 
there is no reason to assume a source would operate with a worse 
efficiency than in their compliance test. Earthjustice Comments p. 9. 
Removal efficiency is, however, a key aspect of normal operating 
variability. Contrary to Earthjustice's suggestion, a source does not 
choose to operate with worse control efficiency. Control equipment 
simply does not operate uniformly day-in, day-out. That variation in 
performance affects emissions and is part of a source's operating 
performance. Moreover, EPA carefully examined whether the sources were 
properly designed and operated during the comparative test conditions 
and determined that they were. TSD Vol. III pp. 17-13 to 16. The 
commenter presents no information questioning that analysis.
    Earthjustice also states repeatedly that EPA selected this floor 
methodology for SVM and LVM to assure that all sources could meet MACT 
floors, citing to 70 FR at 59442. E.g., Earthjustice's Comments p. 11. 
EPA never made such a statement, and the record does not support the 
commenter's assertion. For example, 60% (13 of 22) of incinerators had 
emissions in the relevant test conditions (those considered in 
establishing the standard) that were higher than the SVM floor, and 
over 70% (19 of 26) had higher LVM emissions in those test conditions. 
TSD Vol. III, App. E, Tables SF-INC-SVM and SF-INC-LVM.
2. Standards for Cement Kilns, Lightweight Aggregate Kilns, and Liquid 
Fuel Boilers (Low and High Heating Value Subcategories)
    EPA has determined that these standards should be re-examined and 
not defended in litigation.
3. Alternative to the Particulate Matter Standard for Liquid Fuel 
Boilers
    EPA promulgated alternatives to the particulate matter standard for 
each subcategory of liquid fuel boilers (i.e., high and low heating 
value subcategories) under Sec.  63.1217(e). EPA believes that these 
alternatives require revision for the reasons discussed in the 
September 2007 notice. 72 FR at 54882.
4. Alternative Metal and Total Chlorine Standards for Cement Kilns and 
Lightweight Aggregate Kilns
    EPA promulgated alternatives to the mercury, semivolatile volatile 
metals, low volatile metals, and total chlorine standards for cement 
and lightweight aggregate kilns. See alternatives under Sec.  
63.1206(b)(9), (b)(10), and (b)(15). EPA has determined that these 
alternatives should be re-examined and not defended in litigation. 72 
FR at 54882-83.

C. Standards for Total Chlorine

1. Standards for Incinerators, Cement Kilns, Lightweight Aggregate 
Kilns, Liquid Fuel Boilers, and Solid Fuel Boilers
    All comments on these source categories are already addressed 
either in the final agency action on reconsideration (issue of 
analytical bias with stack sampling method for total chlorine, see 
section III.B of this preamble above), or in earlier parts of this 
rulemaking. TSD Vol. III, Chapter 19. With respect to the standards for 
total chlorine for existing and new cement kilns and liquid fuel 
boilers (high heating value subcategory) and new lightweight aggregate 
kilns, EPA believes these standards require revision

[[Page 64089]]

for the reasons signaled in the September 2007 notice. 72 FR at 54883. 
Finally, with respect to the standards for total chlorine for liquid 
fuel boilers (low heating value subcategory), EPA has determined that 
these standards should also be re-examined and not defended in 
litigation for reasons discussed in section IV.F.3 below.
2. Hydrochloric Acid Production Furnaces
    EPA adheres to the analysis set out in the September 2007 notice: 
The pool of best performing sources are those emitting the least total 
chlorine and EPA has discretion to express these sources' performance 
in terms of percent reduction. Sections 112(i)(5)(A) and 129(a)(4) of 
the Act support this conclusion (a point not addressed by Earthjustice 
in its comments). See 72 FR at 54884/2.
    Earthjustice states that standards expressed in terms of control 
efficiency are not ``emission standards'' under the Act. This is 
incorrect. An ``emission standard'' includes ``a requirement * * * 
which limits the quantity, rate, or concentration of emissions of air 
pollutants on a continuous basis.'' CAA section 302(k). Standards 
requiring HAP reduction of a given percent limit the emission quantity, 
rate, and (in any realistic scenario) concentration of the HAP and so 
falls squarely within the statutory definition.
    Earthjustice stresses the following language from Brick MACT: ``EPA 
cannot circumvent Cement Kiln's holding that section 7412(d)(3) 
requires floors based on the emission level actually achieved by the 
best performers (those with the lowest emission levels), not the 
emission level achievable by all sources * * *''. EPA is not 
establishing a floor for these sources based on an emission level 
achievable by all sources (six of ten sources in the category had test 
conditions with higher (less efficient) performance than the MACT floor 
(see TSD Vol. III, App. E, Table SO-HCLPF-CL)), or otherwise looking to 
performance of sources other than the lowest emitting to establish this 
floor.

D. Standards for Dioxins/Furans

1. Standards for Incinerators
    a. Dry Air Pollution Control Device or Waste Heat Boiler 
Subcategory. The commenter challenges establishing the floor at the 
level of the 2002 Interim Standard. EPA did so because the average of 
the performance of the top 12 percent of lowest emitting sources was 
slightly higher than that level, accounting for run-to-run (short-term) 
variability. TSD Vol. III, App. C, Table E-INCDWHB-DF. Under these 
circumstances, the Interim Standard is the best emissions information 
available to EPA as to the performance of the lowest emitting sources. 
As in Mossville, EPA may establish a MACT floor at a regulatory level 
when the best performing sources performance over time (i.e., 
accounting for variability) ``barely satisfied'' the regulatory limit. 
EPA thus disagrees with the commenter that the floor cannot be 
established at the level of the Interim Standard because the Interim 
Standard is a level sources are required to meet, not the lowest level 
achieved.
    The commenter also continues to dispute that incinerators with dry 
air pollution control devices or waste heat boilers are a separate 
subcategory for purposes of a dioxin/furan standard. As explained at 69 
FR 403 (January 5, 2004), subcategorization on the basis of air 
pollution control technology is not legally permissible. But in this 
case, dry air pollution control devices and waste heat boilers do not 
capture dioxins but form them, making this a different type of process 
for purposes of a dioxin/furan standard.
    b. Wet Air Pollution Control Device or No Air Pollution Control 
Device Subcategory. EPA established the floor at the level of the 
Interim Standard because the lowest emitting sources in single test 
conditions had dioxin emissions in other tests much higher than the 
Interim Standard. EPA's analysis was strongly influenced by comparative 
test data from incinerator source 3016, which appeared to show multiple 
orders of magnitude operating variability. EPA has since re-reviewed 
all of the test data for this source and has found that the amount of 
variability from this source was overstated because results of one of 
the three test runs in test condition 2 were inadvertently omitted from 
the calculation. Remaining sources demonstrate operating variability, 
but not enough to justify retention of the Interim Standard as the MACT 
floor. EPA therefore does not intend to defend this standard in 
litigation, and will re-examine it.
2. Standards for Cement Kilns and Lightweight Aggregate Kilns
    EPA believes it erred in the way in which it assessed the relative 
stringency of the calculated floors and the 2002 Interim Standards 
(i.e., the dioxin/furan standards promulgated under Sec. Sec.  63.1204 
and 63.1205) so that the promulgated standard is expressed incorrectly.
3. Standards for Liquid Fuel Boilers
    For existing liquid fuel boilers-dry air pollution control 
subcategory, the commenter again challenges whether sources with dry 
air pollution control devices can be categorized separately from other 
boilers for purposes of assessing dioxin/furan performance. This point 
is addressed in section IV.D.1.a above. With respect to the remaining 
dioxin/furan standards (new source liquid fuel boilers-dry air 
pollution control subcategory and existing and new source liquid fuel 
boilers-wet or no air pollution control system subcategory), EPA 
believes that these standards require revision for reasons discussed in 
the September 2007 notice. 72 FR at 54886.
4. Standards for Solid Fuel Boilers and Hydrochloric Acid Production 
Furnaces
    As discussed in the September 2007 notice, EPA believes that these 
dioxin/furan standards require revision. 72 FR at 54886.

E. Standards for Non-Dioxin/Furan Organic HAP

    EPA has determined that these standards--carbon monoxide and 
hydrocarbons, as surrogates for control of non-dioxin/furan organic 
HAP--should be re-examined and not defended in litigation.

F. Standards for Mercury

1. Standards for Incinerators
    The commenter challenges use of the 2002 Interim Standard as the 
standard for mercury for existing sources. EPA did so because the 
average of the mercury emissions from the best performing sources under 
any of the possible ranking methodologies was higher than the Interim 
Standard. 72 FR at 54887. The commenter states that this is 
impermissible (although any alternative would lead to a less stringent 
standard than the one EPA promulgated). The commenter further states 
that under Mossville, regulatory levels can constitute a floor if there 
is a factual showing that best performers emit at a level close to that 
regulatory level. Earthjustice's Comments p. 24. EPA agrees. That 
factual showing exists here: The best performers are emitting at a 
level even higher than the regulatory level (reflecting performance 
before the Interim Standard took effect). The regulatory level thus is 
a reasonable measure of best performance. Mossville, 370 F. 3d at 1240-
41.

[[Page 64090]]

2. Standards for Cement Kilns and Lightweight Aggregate Kilns
    As discussed in the September 2007 notice, EPA believes that the 
mercury standards for existing and new cement kilns require revision. 
72 FR at 54887-88. With respect to the mercury standards for existing 
and new lightweight aggregate kilns, EPA has determined that these 
standards should be re-examined and not defended in litigation.
3. Standards for Liquid Fuel Boilers
    In the promulgated rule, EPA had subcategorized liquid fuel boilers 
based on thermal content of hazardous waste burned and established 
separate standards for high heating value and low heating value 
boilers. EPA has determined not to defend the high heating value 
subcategory standards for the reasons stated at 72 FR at 54888. This 
decision also necessitates revision of the mercury standards for the 
low heating value subcategory because all sources' data will now be in 
a common pool--i.e., There will no longer be high and low heating value 
subcategories. See also preamble discussion at III.A above.
4. Standards for Solid Fuel Boilers
    The commenter again raises the issue of consideration of and means 
of calculating run-to-run variability. EPA's response is at 70 FR 
59438-40. EPA continues to believe that these standards are based on 
the average performance of the best performing sources and that EPA has 
reasonably ascertained that level of performance.

G. Normalization

    Ordinarily, one cannot meaningfully compare performance of 
different entities without providing a common metric of comparison. 
Miles per gallon is an example, whereby meaningful comparison of fuel 
economy can be made for vehicles traveling different distances. Stating 
that two vehicles traveled 200 and 300 miles respectively says nothing 
about which has the better fuel economy performance. The commenter 
states nonetheless that normalization is impermissible under section 
112(d)(3). EPA continues to disagree. Section 112(d)(3) does not 
address the issue of whether sources' performance can be expressed and 
compared in normalized units, so the commenter's argument that the 
approach is forbidden as a matter of law appears incorrect. See also 70 
FR at 59451, 72 FR at 54888, and National Lime II, 233 F. 3d at 631, 
632 (rejecting Chevron I argument that section 112(d)(3) requires EPA 
to establish MACT floors ``at the lowest recorded emission level for 
which it has data'' because ``[s]ection [112's] additional phrase says 
nothing about what data the Agency should use to calculate emission 
standards''). EPA's interpretation is moreover reasonable, since 
normalizing emission results allows a meaningful way to determine which 
performers are better, the very purpose of section 112(d)(3).

V. What Other Rule Provisions Are Being Amended or Clarified?

    We are making several corrections to 40 CFR part 63, Subpart EEE. 
In addition, we are clarifying the particulate matter standard for 
cement kilns.

A. What corrections are we making?

1. Revisions to Sec.  63.1207(d)
    The last sentences under Sec.  63.1207(d)(4)(i) and (ii) refer to 
demonstrating compliance with ``the replacement standards promulgated 
on or after October 12, 2005.'' This regulatory language is confusing. 
We are revising these paragraphs to clarify that the ``replacement'' 
standards are the standards under Sec. Sec.  63.1219, 63.1220, and 
63.1221. Accordingly, we are amending Sec.  63.1207(d)(4).
2. Revisions to Sec.  63.1207(m)
    Section 63.1207(m) waives the performance test if the HAP metals or 
total chlorine feed rate (after conversion to an exhaust gas 
concentration using continuously monitored exhaust gas flow data) is 
less than the applicable emission rate, assuming that 100 percent of 
the constituent in the feed is emitted from the combustion unit. This 
provision applies to emission standards expressed either on a 
volumetric flow rate of exhaust gas basis (i.e., [mu]g/dscm or ppmv) or 
on a hazardous waste thermal concentration basis (i.e., pounds of HAP 
emitted attributable to the hazardous waste per million Btu of heat 
input from the hazardous waste).
    The performance test waiver provisions under Sec.  63.1207(m)(1), 
which addresses emission standards expressed on a volumetric flow rate 
of exhaust gas basis, currently state that a source is ``deemed to be 
in compliance with an emission standard * * * if the twelve-hour 
rolling average maximum theoretical emission concentration (MTEC) * * * 
does not exceed the emission standard.'' The twelve-hour rolling 
average requirement under Sec.  63.1207(m)(1) was appropriate when this 
provision was codified in 1999 because all the metals and total 
chlorine feedrate limits were specified as twelve-hour rolling average 
limits. 64 FR at 52967, 53060-62 (September 30, 1999). However, when we 
finalized standards for liquid and solid fuel boilers in 2005, twelve-
hour rolling average limits were not required for all standards. See, 
for example, the rolling average requirements under Sec.  
63.1209(n)(2)(v). Moreover, we also finalized in the 2005 rule a new 
provision that allows sources to use shorter averaging periods than 
those specified in the rule because shorter averaging periods result in 
more stringent control of the parameter. Section 63.1209(r).\72\ EPA 
inadvertently failed to revise Sec.  63.1207(m)(1) to remove the 
twelve-hour rolling average requirement in the October 2005 rule. 
Today, we are correcting that inadvertent error. Accordingly, we are 
revising Sec.  63.1207(m)(1)(i).
---------------------------------------------------------------------------

    \72\ USEPA, ``Technical Support Document for HWC MACT Standards, 
Volume IV: Compliance with the HWC MACT Standards'', September 2005, 
Section 2.2.6.
---------------------------------------------------------------------------

3. Revisions to Sec.  63.1220(a)(2) and (b)(2)
    In an April 8, 2008 rule, we revised the mercury standards under 
Sec.  63.1220(a)(2) and (b)(2) by clarifying that a source must comply 
with the maximum concentration of mercury in the hazardous waste 
limitation and either a hazardous waste maximum theoretical emission 
concentration feed limit or stack gas concentration limit. 73 FR at 
18972 (April 8, 2008) and 71 FR at 52641 (September 6, 2006). However, 
the mercury standards issued on April 8 were not amended correctly, 
which resulted in the maximum theoretical emission concentration feed 
limit requirement being incorrectly repeated under Sec.  
63.1220(a)(2)(iii) and (b)(2)(iii). Today, we are removing Sec.  
63.1220(a)(2)(iii) and (b)(2)(iii), which paragraphs were correctly and 
previously incorporated under Sec.  63.1220(a)(2)(ii) and (b)(2)(ii), 
respectively.

B. Clarification of the PM Standard for Cement Kilns

    In their comments on the proposed rule, the Ash Grove Cement 
Company (Ash Grove) and Cement Kiln Recycling Coalition (CKRC) each 
sought clarification regarding the portion of the new source 
particulate matter (PM) standard specifying that the prescribed 
concentration limit be ``corrected to 7% oxygen.'' \73\ Ash Grove 
raised its point in the context of its plans to build a new cement kiln 
at its Foreman, Arkansas plant. The plant will be configured with an 
energy-saving design in which combustion gases from the kiln and

[[Page 64091]]

non-combustion gases from the clinker cooler would be combined prior to 
passing through the in-line raw mill, the PM control device, and the 
emission stack. The purpose of this configuration is to recover heat 
from the clinker cooler exhaust to aid in drying the raw feed in the 
in-line raw mill. CKRC endorsed Ash Grove's comments and sought the 
clarification more generically with respect to member companies' plans 
to employ similar energy-saving engineering configurations in new kiln 
designs.
---------------------------------------------------------------------------

    \73\ See docket items EPA-HQ-OAR-2004-0022-0538 (p. 5) and -0541 
(p. 2).
---------------------------------------------------------------------------

    Ash Grove and CKRC noted in their comments that, under their 
proposed design, the PM standard would be unattainable if the facility 
were required to correct the combined gas stream to 7 percent oxygen. 
The commenters acknowledged that the oxygen correction procedure is a 
necessary component of a concentration-based emission standard because 
it prevents a facility from meeting the standard by simply diluting the 
regulated, dust-laden gas stream with clean air. In this case, however, 
Ash Grove proposes to combine two regulated, dust-laden gas streams for 
legitimate energy recovery purposes. In their comments, Ash Grove and 
CKRC asked EPA to clarify that, in the Ash Grove design, the oxygen 
associated with the clinker cooler exhaust does not represent dilution 
air and should not be included in the oxygen correction calculation 
when determining compliance with the PM standard of the Subpart EEE 
MACT standard. That is, the oxygen contribution in the combined stream 
attributable to the clinker cooler gas should be ``subtracted'' when 
assessing compliance with the Subpart EEE standard.
    The Agency acknowledges that combining the two regulated gas 
streams, as proposed in the Ash Grove design, is not impermissible 
dilution that the oxygen correction factor of Subpart EEE is meant to 
prevent.\74\ We also recognize that applying the oxygen correction 
factor to the combined gas stream in this case would be tantamount to 
requiring a clinker cooler PM emission rate of zero, which is not 
physically possible.
---------------------------------------------------------------------------

    \74\ See also memorandum entitled ``Potential Environmental 
Benefits of Combining Kiln Combustion and Clinker Cooler Gas,'' 
dated September 15, 2008, in the docket to the rule.
---------------------------------------------------------------------------

    Facilities which opt to combine their emissions streams, for heat 
recovery or other legitimate purposes, are referred to the Agency's 
long standing compliance policy. In the case where two (or more) 
separately-regulated streams are physically combined in common duct 
work prior to control, they are evaluated for compliance with the more 
stringent standard; or, in the case where two (or more) separately 
regulated streams are physically combined for a legitimate process 
purpose, they should be evaluated for compliance with the emission 
standard of the affected facility from which the gases are 
discharged.\75\ These policies were developed specifically for 
application of the opacity standard, where once two (or more) gas 
streams are combined, it is not possible to evaluate them separately.
---------------------------------------------------------------------------

    \75\ See letter from Michael S. Alushin, USEPA, to Evelyn 
Rodriquez Cintron, Commonwealth of Puerto, entitled ``Opacity Limit 
for Commingled Emission Streams,'' dated March 24, 2005; letter from 
Michael S. Alushin, USEPA, to Francis Torres, Torres and Garcia 
P.S.C., entitled ``Opacity Limit for Commingled Emission Streams,'' 
dated March 24, 2005; memorandum from John B. Rasnic, USEPA, to 
USEPA Regional Directors and Regional Counsels, entitled ``Opacity 
Limitation for In-line Portland Cement Plants,'' dated September 7, 
1996; and memorandum from John B. Rasnic, USEPA, to USEPA Regional 
Directors and Regional Counsels, entitled ``Opacity Limitations for 
the Portland Cement Plant New Source Performance Standards,'' dated 
April 6, 1995. These documents are available on the Agency's 
Applicability Determination Index Web site at http://cfpub.epa.gov/
adi/.
---------------------------------------------------------------------------

    In the case of streams combined from the clinker cooler and the 
kiln, where separate PM emission standards apply, facilities may submit 
site-specific compliance procedures to eliminate the effect of the 
clinker cooler exhaust gas on the Subpart EEE oxygen correction 
calculation. Any method proposed must be evaluated against the 
standards forbidding circumvention at 40 CFR 63.4(b) and against the 
requirements to provide means for accurate sampling of applicable 
emission standards at 40 CFR 63.7(d). Any claims made under these 
provisions should be submitted to the appropriate delegated authority 
for site-specific implementation.
    Two commenters raised procedural objections to the Ash Grove and 
CKRC requests for clarification on this oxygen correction issue.\76\ 
These comments appear to be based on the premise that EPA legally would 
be required to publish a new notice of proposed rulemaking before 
clarifying the issue. We disagree that such a new notice is necessary 
in situations such as this, where it is merely responding to requests 
for clarification and the clarification is fully consistent with the 
plain text of the governing regulation (as explained above). EPA also 
provided actual notice to all commenters and invited reply comments on 
the issue, both a permissible means of giving notice and one which 
removes any possible prejudice to persons receiving such notice. See 
Small Refiners lead Phase-Down Task Force v. EPA, 705 F. 2d 506, 540, 
549 (D.C. Cir. 1983).
---------------------------------------------------------------------------

    \76\ See docket items EPA-HQ-OAR-2004-0022-0548 and -0579.
---------------------------------------------------------------------------

VI. Summary of Environmental, Energy, and Economic Impacts

A. What facilities are affected by the final amendments?

    A description of the affected source categories is discussed in the 
April 20, 2004 proposed rule. 69 FR at 21207-09. In the October 12, 
2005 final rule, we estimated that there are a total of 267 sources 
subject to the rule requirements, including 116 boilers (104 liquid 
fuel boilers and 12 solid fuel boilers), 92 on-site incinerators, 25 
cement kilns, 15 commercial incinerators, nine lightweight aggregate 
kilns, and ten hydrochloric acid production furnaces. 70 FR at 59530. 
While we are aware of several changes to the universe of operating 
hazardous waste combustors, these estimates remain a reasonable 
representation of existing operating sources.\77\
---------------------------------------------------------------------------

    \77\ Given the small size of the lightweight aggregate kiln 
category, it is worth mentioning that the Solite Cascade plant in 
Virginia has ceased operations. Prior to closure, this plant 
operated four kiln sources. See also 70 FR at 59426.
---------------------------------------------------------------------------

    Today's action also revises the particulate matter standards for 
new cement kilns and new incinerators. Based on comments received in 
response to the March 23, 2006 proposed rule, EPA does not believe that 
there are any cement kiln or incinerator sources that are currently 
complying with the new source particulate matter standards. In 
addition, EPA estimates that the majority of, if not all, sources that 
will be subject to the revised new source standards over the next five 
years will not be greenfield sources, but sources that upgrade at 
existing facilities (e.g., a new state-of-the-art preheater/precalciner 
kiln to replace one or more existing wet process cement kilns).\78\
---------------------------------------------------------------------------

    \78\ Examples of cement plants pursuing plant modernizations can 
be found in several docket items, including EPA-HQ-OAR-2004-0022-
0383 (pg. 4), EPA-HQ-OAR-2004-0022-0521 (Attachments F, G, and H), 
and EPA-HQ-OAR-2004-0022-0604 (pg. 8).
---------------------------------------------------------------------------

B. What are the air quality impacts?

    For existing sources, we estimate that there will be no air 
emission impacts as the result of this rule. This is because today's 
rule is not revising any of the emission standards promulgated in the 
October 12, 2005 final rule. Furthermore, the final amendments to the 
compliance and monitoring provisions will not affect the current level 
of control at existing facilities subject to the rule.

[[Page 64092]]

    For new sources, we are promulgating revised particulate matter 
standards for cement kilns and incinerators. The revised particulate 
matter standards for new cement kilns and new incinerators are 0.0069 
gr/dscf (an increase from 0.0023 gr/dscf) and 0.0016 gr/dscf (an 
increase from 0.0015 gr/dscf), corrected to 7 percent oxygen, 
respectively. For a new preheater/precalciner cement kiln with an 
average gas flow rate of 250,000 dry standard cubic feet per minute 
(dscfm) emitting particulate matter at 0.0069 gr/dscf, we estimate 
emissions of particulate matter would be approximately 59 tons per 
year. A similarly designed new cement kiln emitting particulate matter 
at 0.0023 gr/dscf would emit approximately 20 tons per year. And for an 
incinerator with an average gas flow rate of 25,000 dscfm, we estimate 
that particulate matter emissions would increase by approximately 170 
pounds per year per new incinerator if it were emitting particulate 
matter at 0.0016 gr/dscf as compared to 0.0015 gr/dscf. However, as 
discussed in section VI.A above, we do not believe that there are any 
cement kiln or incinerator sources that are currently in operation and 
complying with the particulate matter standards for new sources. Thus, 
we estimate that there will be no actual increases in particulate 
matter emissions at currently operating facilities as a result of 
today's action. Moreover, we believe that the majority of new cement 
kiln and incinerator sources over the next five years will be sources 
that upgrade at existing facilities (e.g., an older existing source 
replaced by a new source). See discussion in section VI.A above. For 
these facilities, particulate matter emissions will actually decrease 
from current levels because the new source standards finalized today 
are more stringent than the standards for existing sources. For 
example, the reduction in particulate matter emissions for a new 
preheater/precalciner cement kiln with an average gas flow rate of 
250,000 dscfm emitting particulate matter at 0.028 gr/dscf (the 
existing source standard) as compared to 0.0069 gr/dscf (the new source 
standard) is approximately 180 tons per year.\79\
---------------------------------------------------------------------------

    \79\ USEPA, ``Technical Support Document for HWC MACT Standards: 
Petitions for Reconsideration Support Document,'' October 2008, 
Section 2.3.3.
---------------------------------------------------------------------------

C. What are the water quality, solid waste, energy, cost and economic 
impacts?

    This rule will result in negligible impacts to water quality, solid 
waste, and energy requirements from levels presented in the October 12, 
2005 rule. 70 FR at 59529. We likewise estimate minimal cost and no 
economic impacts (as compared with the total costs and economic impacts 
that were calculated for the October 12, 2005 rule).\80\
---------------------------------------------------------------------------

    \80\ USEPA, ``Technical Support Document for HWC MACT Standards: 
Petitions for Reconsideration Support Document,'' October 2008, 
Section 7.
---------------------------------------------------------------------------

VII. Statutory and Executive Order Reviews

A. Executive Order 12866: Regulatory Planning and Review

    Under Executive Order (EO) 12866 (58 FR 51735, October 4, 1993), 
this action is a ``significant regulatory action'' because it raises 
novel legal or policy issues. Accordingly, EPA submitted this action to 
the Office of Management and Budget (OMB) for review under EO 12866 and 
any changes made in response to OMB recommendations have been 
documented in the docket for this action.
    In addition, this final rule is not considered to be an 
economically significant action because the social costs for this rule 
are significantly below the $100 million threshold established for 
economically significant actions. This is because this final rule does 
not have any significant new regulatory requirements as compared to the 
requirements discussed in the October 12, 2005 final rule, a rule with 
estimated total social costs of $22.6 million per year. See 70 FR at 
59537.

B. Paperwork Reduction Act

    This action does not impose any new information collection burden. 
Today's rule amendments consist of new compliance options, 
clarifications, and corrections to the existing rule that impose no new 
net information collection requirements on industry or EPA. However, 
the Office of Management and Budget (OMB) has previously approved the 
information collection requirements contained in the existing 
regulations (see 40 CFR part 9) under the provisions of the Paperwork 
Reduction Act, 44 U.S.C. 3501 et seq. and has assigned OMB control 
number 2050-0171, EPA ICR number 1773.08. The OMB control numbers for 
EPA's regulations in 40 CFR are listed in 40 CFR part 9.

C. Regulatory Flexibility Act

    The Regulatory Flexibility Act (RFA) generally requires an agency 
to prepare a regulatory flexibility analysis of any rule subject to 
notice and comment rulemaking requirements under the Administrative 
Procedure Act or any other statute unless the agency certifies that the 
rule will not have a significant economic impact on a substantial 
number of small entities. Small entities include small businesses, 
small organizations, and small governmental jurisdictions.
    For purposes of assessing the impacts of today's rule on small 
entities, small entity is defined as: (1) A small business as defined 
by the Small Business Administration's (SBA) regulations at 13 CFR 
121.201; (2) a small governmental jurisdiction that is a government of 
a city, county, town, school district or special district with a 
population of less than 50,000; and (3) a small organization that is 
any ``not-for-profit enterprise which is independently owned and 
operated and is not dominant in its field.''
    After considering the economic impacts of today's final rule on 
small entities, I certify that this action will not have a significant 
economic impact on a substantial number of small entities. As discussed 
in the October 12, 2005 final rule (of which today's final rule 
amends), we determined that hazardous waste combustion facilities are 
not owned by small governmental jurisdiction or nonprofit 
organizations. 70 FR at 59538. Therefore, in that rule only small 
businesses were analyzed for small entity impacts (a small entity was 
defined either by the number of employees or by the dollar amount of 
sales). We found that few--a total of eight out of 145 facilities--of 
the sources affected by the October 2005 rule were owned by small 
businesses. Finally, our analysis indicated that none of these 
facilities are likely to incur annualized compliance costs greater than 
one percent of gross annual corporate revenues. Cost impacts were found 
to range from less than 0.01 percent to 0.46 percent of annual gross 
corporate revenues. 70 FR at 59538.
    Although this final rule will not have a significant economic 
impact on a substantial number of small entities, EPA nonetheless has 
tried to reduce the impact of this rule on small entities. We note that 
today's final rule does not alter the number or type of small 
businesses that were discussed in the October 12, 2005 final rule. In 
addition, this rule revises or clarifies several compliance provisions 
that increases flexibility and improves implementation.

D. Unfunded Mandates Reform Act

    This rule does not contain a Federal mandate that may result in 
expenditures of $100 million or more for State, local, and tribal 
governments, in the aggregate, or the private sector in any one year.

[[Page 64093]]

EPA is taking this action to make certain amendments, corrections, and 
clarifications to the October 12, 2005 final rule (70 FR 59402 and 
59538). Thus, this rule is not subject to the requirements of section 
202 and 205 of UMRA.
    This rule is also not subject to the requirements of section 203 of 
UMRA because it contains no regulatory requirements that might 
significantly or uniquely affect small governments. The amendments, 
corrections, and clarifications made through this action contain no 
requirements that apply to such governments, impose no obligations upon 
them, and will not result in any expenditures by them or any 
disproportionate impacts on them. This rule is not subject to section 
203 of UMRA.

E. Executive Order 13132: Federalism

    Executive Order 13132, entitled ``Federalism'' (64 FR 43255, August 
10, 1999), requires EPA to develop an accountable process to ensure 
``meaningful and timely input by State and local officials in the 
development of regulatory policies that have federalism implications.'' 
``Policies that have federalism implications'' is defined in the 
Executive Order to include regulations that have ``substantial direct 
effects on the States, on the relationship between the national 
government and the States, or on the distribution of power and 
responsibilities among the various levels of government.''
    This final rule does not have federalism implications. The final 
rule does not have substantial direct effects on the States, on the 
relationship between the national government and the States, or on the 
distribution of power and responsibilities among the various levels of 
government, as specified in Executive Order 13132. This rule makes 
certain amendments, corrections, and clarifications to the October 12, 
2005 final rule (70 FR 59402 and 59538). These final amendments and 
clarifications do not impose requirements on State and local 
governments. Thus, Executive Order 13132 does not apply to this rule.

F. Executive Order 13175: Consultation and Coordination With Indian 
Tribal Governments

    This action does not have tribal implications, as specified in 
Executive Order 13175 (65 FR 67249, November 9, 2000). Today's rule 
amendments, corrections, and clarifications do not impose requirements 
on tribal governments. They also have no direct effects on tribal 
governments, on the relationship between the Federal government and 
Indian tribes, or on the distribution of power and responsibilities 
between the Federal government and Indian tribes. Finally, tribal 
governments do not own or operate any sources subject to the Hazardous 
Waste Combustor MACT rule. Thus, Executive Order 13175 does not apply 
to this rule.

G. Executive Order 13045: Protection of Children From Environmental 
Health Risks and Safety Risks

    EPA interprets Executive Order 13045 (62 FR 19885, April 23, 1997) 
as applying to those regulatory actions that concern health or safety 
risks, such that the analysis required under section 5-501 of the Order 
has the potential to influence the regulation. This final rule is not 
subject to Executive Order 13045 because it is based solely on 
technology performance. Furthermore, this final rule is not considered 
``economically significant'' as defined under EO 12866.

H. Executive Order 13211: Actions Concerning Regulations That 
Significantly Affect Energy Supply, Distribution, or Use

    This rule is not a ``significant energy action'' as defined in 
Executive Order 13211 (66 FR 28355 (May 22, 2001)) because it is not 
likely to have a significant adverse effect on the supply, 
distribution, or use of energy. Further, we have concluded that this 
rule is not likely to have any adverse energy effects because energy 
requirements will not be significantly impacted by the amendments, 
corrections, and clarifications finalized by this action.

I. National Technology Transfer and Advancement Act

    Section 12(d) of the National Technology Transfer and Advancement 
Act of 1995 (``NTTAA''), Public Law 104-113, 12(d) (15 U.S.C. 272 note) 
directs EPA to use voluntary consensus standards in its regulatory 
activities unless to do so would be inconsistent with applicable law or 
otherwise impractical. Voluntary consensus standards are technical 
standards (e.g., materials specifications, test methods, sampling 
procedures, and business practices) that are developed or adopted by 
voluntary consensus standards bodies. NTTAA directs EPA to provide 
Congress, through OMB, explanations when the Agency decides not to use 
available and applicable voluntary consensus standards.
    The amendments, corrections, and clarifications finalized today do 
not involve technical standards. Therefore, EPA did not consider the 
use of any voluntary consensus standards.

J. Executive Order 12898: Federal Actions to Address Environmental 
Justice in Minority Populations and Low-Income Populations

    Executive Order 12898 (59 FR 7629 (Feb. 16, 1994)) establishes 
federal executive policy on environmental justice. Its main provision 
directs federal agencies, to the greatest extent practicable and 
permitted by law, to make environmental justice part of their mission 
by identifying and addressing, as appropriate, disproportionately high 
and adverse human health or environmental effects of their programs, 
policies, and activities on minority populations and low-income 
populations in the United States.
    EPA has determined that this final rule will not have 
disproportionately high and adverse human health or environmental 
effects on minority or low income populations because it does not 
affect the level of protection provided to human health or the 
environment. The corrections and clarifications in today's rule will 
not affect the current level of control at facilities subject to these 
rules. In addition, for reasons discussed in Section VI above, we 
estimate that the revised particulate matter emission standards for new 
cement kilns and new incinerators will not result in any adverse or 
disproportional health or safety effects on minority or low-income 
populations. As a result, we believe our findings regarding Executive 
Order 12898 published in the October 12, 2005 rule are not adversely 
impacted by today's action. 70 FR at 59539.

K. Congressional Review

    The Congressional Review Act, 5 U.S.C. 801 et seq., as added by the 
Small Business Regulatory Enforcement Fairness Act of 1996, generally 
provides that before a rule may take effect, the agency promulgating 
the rule must submit a rule report, which includes a copy of the rule, 
to each House of the Congress and to the Comptroller General of the 
United States. EPA will submit a report containing this action and 
other required information to the U.S. Senate, the U.S. House of 
Representatives, and the Comptroller General of the United States prior 
to publication of the rule in the Federal Register. A major rule cannot 
take effect until 60 days after it is published in the Federal 
Register. This action is not a ``major action'' as defined by 5 U.S.C. 
804(2). This final rule will be effective on October 28, 2008.

[[Page 64094]]

List of Subjects in 40 CFR Part 63

    Environmental protection, Air pollution control, Hazardous 
substances, Reporting and recordkeeping requirements.

    Dated: October 16, 2008.
Stephen L. Johnson,
Administrator.

0
For the reasons set out in the preamble, title 40, chapter I of the 
Code of Federal Regulations is amended as follows:

PART 63--NATIONAL EMISSIONS STANDARDS FOR HAZARDOUS AIR POLLUTANTS 
FOR SOURCE CATEGORIES

0
1. The authority citation for part 63 continues to read as follows:

    Authority: 42 U.S.C. 7401 et seq.


0
2. Section 63.1206 is amended as follows:
0
a. By revising paragraph (a)(1)(ii)(B)(3).
0
b. By revising paragraphs (c)(8)(iii), (c)(8)(iv), and (c)(9).


Sec.  63.1206  When and how must you comply with the standards and 
operating requirements?

    (a) * * *
    (1) * * *
    (ii) * * *
    (B) * * *
    (3) If you commenced construction or reconstruction of a cement 
kiln after April 20, 2004, you must comply with the new source emission 
standard for particulate matter under Sec.  63.1220(b)(7)(i) by the 
later of October 28, 2008 or the date the source starts operations.
* * * * *
    (c) * * *
    (8) * * *
    (iii) Bag leak detection system corrective measures requirements. 
The operating and maintenance plan required by paragraph (c)(7) of this 
section must include a corrective measures plan that specifies the 
procedures you will follow in the case of a bag leak detection system 
alarm or malfunction. The corrective measures plan must include, at a 
minimum, the procedures used to determine and record the time and cause 
of the alarm or bag leak detection system malfunction in accordance 
with the requirements of paragraph (c)(8)(iii)(A) of this section as 
well as the corrective measures taken to correct the control device or 
bag leak detection system malfunction or to minimize emissions in 
accordance with the requirements of paragraph (c)(8)(iii)(B) of this 
section. Failure to initiate the corrective measures required by this 
paragraph is failure to ensure compliance with the emission standards 
in this subpart.
    (A) You must initiate the procedures used to determine the cause of 
the alarm or bag leak detection system malfunction within 30 minutes of 
the time the alarm first sounds; and
    (B) You must alleviate the cause of the alarm or bag leak detection 
system malfunction by taking the necessary corrective measure(s) which 
may include, but are not to be limited to, the following:
    (1) Inspecting the baghouse for air leaks, torn or broken filter 
elements, or any other malfunction that may cause an increase in 
emissions;
    (2) Sealing off defective bags or filter media;
    (3) Replacing defective bags or filter media, or otherwise 
repairing the control device;
    (4) Sealing off a defective baghouse compartment;
    (5) Cleaning the bag leak detection system probe, or otherwise 
repairing the bag leak detection system; or
    (6) Shutting down the combustor.
    (iv) Excessive exceedances notification. If you operate the 
combustor when the detector response exceeds the alarm set-point or the 
bag leak detection system is malfunctioning more than 5 percent of the 
time during any 6-month block time period, you must submit a 
notification to the Administrator within 30 days of the end of the 6-
month block time period that describes the causes of the exceedances 
and bag leak detection system malfunctions and the revisions to the 
design, operation, or maintenance of the combustor, baghouse, or bag 
leak detection system you are taking to minimize exceedances and bag 
leak detection system malfunctions. To document compliance with this 
requirement:
    (A) You must keep records of the date, time, and duration of each 
alarm and bag leak detection system malfunction, the time corrective 
action was initiated and completed, and a brief description of the 
cause of the alarm or bag leak detection system malfunction and the 
corrective action taken;
    (B) You must record the percent of the operating time during each 
6-month period that the alarm sounds and the bag leak detection system 
malfunctions;
    (C) If inspection of the fabric filter demonstrates that no 
corrective action is required, then no alarm time is counted; and
    (D) If corrective action is required, each alarm shall be counted 
as a minimum of 1 hour. Each bag leak detection system malfunction 
shall also be counted as a minimum of 1 hour.
    (9) Particulate matter detection system requirements. You must 
continuously operate a particulate matter detection system (PMDS) that 
meets the specifications and requirements of paragraphs (c)(9)(i) 
through (v) of this section and you must comply with the corrective 
measures and notification requirements of paragraphs (c)(9)(vii) and 
(viii) of this section if your combustor either: Is equipped with an 
electrostatic precipitator or ionizing wet scrubber and you do not 
establish site-specific control device operating parameter limits under 
Sec.  63.1209(m)(1)(iv) that are linked to the automatic waste feed 
cutoff system under paragraph (c)(3) of this section, or is equipped 
with a baghouse (fabric filter) and you do not operate a bag leak 
detection system as provided by paragraph (c)(8)(i)(B) of this section.
    (i) PMDS requirements.--(A) The PMDS must be certified by the 
manufacturer to be capable of continuously detecting and recording 
particulate matter emissions at concentrations of 1.0 milligrams per 
actual cubic meter unless you demonstrate, under Sec.  63.1209(g)(1), 
that a higher detection limit would routinely detect particulate matter 
loadings during normal operations;
    (B) The particulate matter detector shall provide output of 
relative or absolute particulate matter loadings;
    (C) The PMDS shall be equipped with an alarm system that will sound 
an audible alarm when an increase in relative or absolute particulate 
loadings is detected over the set-point;
    (D) You must install, operate, and maintain the PMDS in a manner 
consistent with the provisions of paragraph (c)(9) of this section and 
available written guidance from the U.S. Environmental Protection 
Agency or, in the absence of such written guidance, the manufacturer's 
written specifications and recommendations for installation, operation, 
maintenance and quality assurance of the system.
    (1) Set-points established without extrapolation. If you establish 
the alarm set-point without extrapolation under paragraph 
(c)(9)(iii)(A) of this section, you must request approval from the 
regulatory authority, in the continuous monitoring system test plan, of 
the quality assurance procedures that will reasonably ensure that PMDS 
response values below the alarm set-point correspond to PM emission 
concentrations below those demonstrated during the comprehensive 
performance test. Your recommended

[[Page 64095]]

quality assurance procedures may include periodic testing under as-
found conditions (i.e., normal operations) to obtain additional PM 
concentration and PMDS response run pairs, as warranted.
    (2) Set-points established with extrapolation. If you establish the 
alarm set-point by extrapolation under paragraph (c)(9)(iii)(B) of this 
section, you must request approval from the regulatory authority, in 
the continuous monitoring system test plan, of the quality assurance 
procedures that will reasonably ensure that PMDS response values below 
the alarm set-point correspond to PM emission concentrations below the 
value that correlates to the alarm set-point.
    (E) You must include procedures for installation, operation, 
maintenance, and quality assurance of the PMDS in the site-specific 
continuous monitoring system test plan required under Sec. Sec.  
63.1207(e) and 63.8(e)(3);
    (F) Where multiple detectors are required to monitor multiple 
control devices, the system's instrumentation and alarm system may be 
shared among the detectors.
    (G) You must establish the alarm set-point as a 6-hour rolling 
average as provided by paragraphs (c)(9)(ii), (c)(9)(iii), and 
(c)(9)(iv) of this section;
    (H) Your PMDS must complete a minimum of one cycle of operation 
(sampling, analyzing, and data recording) for each successive 15-minute 
period. You must update the 6-hour rolling average of the detector 
response each hour with a one-hour block average that is the average of 
the detector responses over each 15-minute block; and
    (I) If you exceed the alarm set-point (or if your PMDS 
malfunctions), you must comply with the corrective measures under 
paragraph (c)(9)(vii) of this section.
    (ii) Establishing the alarm set-point for operations under the 
Documentation of Compliance. You must establish the alarm set-point for 
operations under the Documentation of Compliance (i.e., after the 
compliance date but prior to submitting a Notification of Compliance 
subsequent to conducting the initial comprehensive performance test) of 
an existing source as follows:
    (A) You must obtain a minimum of three pairs of Method 5 or 5I 
data, provided in appendix A-3 to part 60 of this chapter, and PMDS 
data to establish an approximate correlation curve. Data obtained up to 
60 months prior to the compliance date may be used provided that the 
design and operation of the combustor or PMDS has not changed in a 
manner that may adversely affect the correlation of PM concentrations 
and PMDS response.
    (B) You must request approval from the regulatory authority, in the 
continuous monitoring system test plan, of your determination whether 
multiple correlation curves are needed considering the design and 
operation of your combustor and PMDS.
    (C) You must approximate the correlation of the reference method 
data to the PMDS data.
    (1) You may assume a linear correlation of the PMDS response to 
particulate matter emission concentrations;
    (2) You may include a zero point correlation value. To establish a 
zero point, you must follow one or more of the following steps:
    (i) Zero point data for in-situ instruments should be obtained, to 
the extent possible, by removing the instrument from the stack and 
monitoring ambient air on a test bench;
    (ii) Zero point data for extractive instruments should be obtained 
by removing the extractive probe from the stack and drawing in clean 
ambient air;
    (iii) Zero point data also can be obtained by performing manual 
reference method measurements when the flue gas is free of PM emissions 
or contains very low PM concentrations (e.g., when your process is not 
operating, but the fans are operating or your source is combusting only 
natural gas); and
    (iv) If none of the steps in paragraphs (c)(9)(ii)(B)(2)(i) through 
(iii) of this section are possible, you must estimate the monitor 
response when no PM is in the flue gas (e.g., 4 mA = 0 mg/acm).
    (3) For reference method data that were obtained from runs during a 
test condition where controllable operating factors were held constant, 
you must average the test run averages of PM concentrations and PMDS 
responses to obtain a single pair of data for PM concentration and PMDS 
response. You may use this pair of data and the zero point to define a 
linear correlation model for the PMDS.
    (D) You must establish the alarm set-point as the PMDS response 
that corresponds to a PM concentration that is 50% of the PM emission 
standard or 125% of the highest PM concentration used to develop the 
correlation, whichever is greater. For reference method data that were 
obtained from runs during a test condition where controllable operating 
factors were held constant, you must use the average of the test run 
averages of PM concentrations for extrapolating the alarm set-point. 
The PM emission concentration used to extrapolate the alarm set-point 
must not exceed the PM emission standard, however.
    (iii) Establishing the initial alarm set-point for operations under 
the Notification of Compliance. You must establish the initial alarm 
set-point for operations under the Notification of Compliance as 
provided by either paragraph (c)(9)(iii)(A) or paragraph (c)(9)(iii)(B) 
of this section. You must periodically revise the alarm set-point as 
provided by paragraph (c)(9)(iv) of this section.
    (A) Establishing the initial set-point without extrapolation. (1) 
If you establish the initial alarm set-point without extrapolation, the 
alarm set-point is the average of the test run averages of the PMDS 
response during the runs of the comprehensive performance test that 
document compliance with the PM emission standard.
    (2) During the comprehensive performance test, you may simulate PM 
emission concentrations at the upper end of the range of normal 
operations by means including feeding high levels of ash and detuning 
the emission control equipment.
    (B) Establishing the initial set-point by extrapolation. You may 
extrapolate the particulate matter detector response to establish the 
alarm set-point under the following procedures:
    (1) You must request approval from the regulatory authority, in the 
continuous monitoring system test plan, of the procedures you will use 
to establish an approximate correlation curve using the three pairs of 
Method 5 or 5I data (see methods in appendix A-3 of part 60 of this 
chapter) and PMDS data from the comprehensive performance test, the 
data pairs used to establish the correlation curve for the 
Documentation of Compliance under paragraph (c)(9)(ii) of this section, 
and additional data pairs, as warranted.
    (2) You must request approval from the regulatory authority, in the 
continuous monitoring system test plan, of your determination of 
whether multiple correlation curves are needed considering the design 
and operation of your combustor and PMDS. If so, you must recommend the 
number of data pairs needed to establish those correlation curves and 
how the data will be obtained.
    (3) During the comprehensive performance test, you may simulate PM 
emission concentrations at the upper end of the range of normal 
operations by means including feeding high levels of ash and detuning 
the emission control equipment.
    (4) Data obtained up to 60 months prior to the comprehensive 
performance

[[Page 64096]]

test may be used provided that the design and operation of the 
combustor or PMDS has not changed in a manner that may adversely affect 
the correlation of PM concentrations and PMDS response.
    (5) You may include a zero point correlation value. To establish a 
zero point, you must follow the procedures under paragraph 
(c)(9)(ii)(C)(2) of this section.
    (6) You must use a least-squares regression model to correlate PM 
concentrations to PMDS responses for data pairs. You may assume a 
linear regression model approximates the relationship between PM 
concentrations and PMDS responses.
    (7) You must establish the alarm set-point as the PMDS response 
that corresponds to a PM concentration that is 50% of the PM emission 
standard or 125% of the highest PM concentration used to develop the 
correlation, whichever is greater. The emission concentration used to 
extrapolate the PMDS response must not exceed the PM emission standard.
    (iv) Revising the Notification of Compliance alarm set-point. (A) 
Revising set-points established without extrapolation. If you establish 
the alarm set-point without extrapolation under paragraph 
(c)(9)(iii)(A) of this section, you must establish a new alarm set-
point in the Notification of Compliance following each comprehensive 
performance test as the average of the test run averages of the PMDS 
response during the runs of the comprehensive performance test that 
document compliance with the PM emission standard.
    (B) Revising set-points established with extrapolation. If you 
establish the alarm set-point by extrapolation under paragraph 
(c)(9)(iii)(B) of this section, you must request approval from the 
regulatory authority, in the continuous monitoring system test plan, of 
the procedures for periodically revising the alarm set-point, 
considering the additional data pairs obtained during periodic 
comprehensive performance tests and data pairs obtained from other 
tests, such as for quality assurance.
    (v) Quality assurance. (A) Set-points established without 
extrapolation. If you establish the alarm set-point without 
extrapolation under paragraph (c)(9)(iii)(A) of this section, you must 
request approval from the regulatory authority, in the continuous 
monitoring system test plan, of the quality assurance procedures that 
reasonably ensure that PMDS response values below the alarm set-point 
correspond to PM emission concentrations below the average of the PM 
concentrations demonstrated during the comprehensive performance test. 
Your recommended quality assurance procedures may include periodic 
testing under as-found conditions (i.e., normal operations) to obtain 
additional PM concentration and PMDS response run pairs, as warranted.
    (B) Set-points established with extrapolation. If you establish the 
alarm set-point by extrapolation under paragraph (c)(9)(iii)(B) of this 
section, you must request approval from the regulatory authority, in 
the continuous monitoring system test plan, of the quality assurance 
procedures that reasonably ensure that PMDS response values below the 
alarm set-point correspond to PM emission concentrations below the 
value that correlated to the alarm set-point.
    (vi) PMDS are used for compliance assurance only. For a PMDS for 
which the alarm set-point is established by extrapolation using a 
correlation curve under paragraphs (c)(9)(ii), (c)(9)(iii)(B), and 
(c)(9)(iv)(B) of this section, an exceedance of the PMDS response that 
appears to correlate with a PM concentration that exceeds the PM 
emission standard is not by itself evidence that the standard has been 
exceeded.
    (vii) PMDS corrective measures requirements. The operating and 
maintenance plan required by paragraph (c)(7) of this section must 
include a corrective measures plan that specifies the procedures you 
will follow in the case of a PMDS alarm or malfunction. The corrective 
measures plan must include, at a minimum, the procedures used to 
determine and record the time and cause of the alarm or PMDS 
malfunction as well as the corrective measures taken to correct the 
control device or PMDS malfunction or minimize emissions as specified 
below. Failure to initiate the corrective measures required by this 
paragraph is failure to ensure compliance with the emission standards 
in this subpart.
    (A) You must initiate the procedures used to determine the cause of 
the alarm or PMDS malfunction within 30 minutes of the time the alarm 
first sounds or the PMDS malfunctions; and
    (B) You must alleviate the cause of the alarm or the PMDS 
malfunction by taking the necessary corrective measure(s) which may 
include shutting down the combustor.
    (viii) Excessive exceedances notification. If you operate the 
combustor when the detector response exceeds the alarm set-point or 
when the PMDS is malfunctioning more than 5 percent of the time during 
any 6-month block time period, you must submit a notification to the 
Administrator within 30 days of the end of the 6-month block time 
period that describes the causes of the exceedances and the revisions 
to the design, operation, or maintenance of the combustor, emission 
control device, or PMDS you are taking to minimize exceedances. To 
document compliance with this requirement:
    (A) You must keep records of the date, time, and duration of each 
alarm and PMDS malfunction, the time corrective action was initiated 
and completed, and a brief description of the cause of the alarm or 
PMDS malfunction and the corrective action taken;
    (B) You must record the percent of the operating time during each 
6-month period that the alarm sounds and the PMDS malfunctions;
    (C) If inspection of the emission control device demonstrates that 
no corrective action is required, then no alarm time is counted; and
    (D) If corrective action to the emission control device is 
required, each alarm shall be counted as a minimum of 1 hour. Each PMDS 
malfunction shall also be counted as a minimum of 1 hour.

0
3. Section 63.1207 is amended by revising paragraphs (d)(4) and 
(m)(1)(i) introductory text to read as follows:


Sec.  63.1207  What are the performance testing requirements?

* * * * *
    (d) * * *
    (4) Applicable testing requirements under the interim standards. 
(i) Waiver of periodic comprehensive performance tests. Except as 
provided by paragraph (c)(2) of this section, you must conduct only an 
initial comprehensive performance test under the interim standards 
(Sec. Sec.  63.1203 through 63.1205); all subsequent comprehensive 
performance testing requirements are waived under the interim 
standards. The provisions in the introductory text to paragraph (d) and 
in paragraph (d)(1) of this section apply only to tests used to 
demonstrate compliance with the standards under Sec. Sec.  63.1219 
through 63.1221.
    (ii) Waiver of confirmatory performance tests. You are not required 
to conduct a confirmatory test under the interim standards (Sec. Sec.  
63.1203 through 63.1205). The confirmatory testing requirements in the 
introductory text to paragraph (d) and in paragraph (d)(2) of this 
section apply only after you have demonstrated compliance with the 
standards under Sec. Sec.  63.1219 through 63.1221.
* * * * *
    (m) * * *
    (1) * * * (i) You are deemed to be in compliance with an emission 
standard based on the volumetric flow rate of

[[Page 64097]]

exhaust gas (i.e., [mu]g/dscm or ppmv) if the maximum theoretical 
emission concentration (MTEC) does not exceed the emission standard 
over the relevant averaging period specified under Sec.  63.1209(l), 
(n), and (o) of this section for the standard:
* * * * *

0
4. Section 63.1210 is amended by revising the table in paragraph (a)(1) 
to read as follows:


Sec.  63.1210  What are the notification requirements?

    (a) * * *
    (1) * * *

------------------------------------------------------------------------
                 Reference                          Notification
------------------------------------------------------------------------
63.9(b)...................................  Initial notifications that
                                             you are subject to Subpart
                                             EEE of this Part.
63.9(d)...................................  Notification that you are
                                             subject to special
                                             compliance requirements.
63.9(j)...................................  Notification and
                                             documentation of any change
                                             in information already
                                             provided under Sec.   63.9.
63.1206(b)(5)(i)..........................  Notification of changes in
                                             design, operation, or
                                             maintenance.
63.1206(c)(8)(iv).........................  Notification of excessive
                                             bag leak detection system
                                             exceedances.
63.1206(c)(9)(v)..........................  Notification of excessive
                                             particulate matter
                                             detection system
                                             exceedances.
63.1207(e), 63.9(e) 63.9(g)(1) and (3)....  Notification of performance
                                             test and continuous
                                             monitoring system
                                             evaluation, including the
                                             performance test plan and
                                             CMS performance evaluation
                                             plan.\1\
63.1210(b)................................  Notification of intent to
                                             comply.
63.1210(d), 63.1207(j), 63.1207(k),         Notification of compliance,
 63.1207(l), 63.9(h), 63.10(d)(2),           including results of
 63.10(e)(2).                                performance tests and
                                             continuous monitoring
                                             system performance
                                             evaluations.
------------------------------------------------------------------------
\1\ You may also be required on a case-by-case basis to submit a
  feedstream analysis plan under Sec.   63.1209(c)(3).

* * * * *

0
5. Section 63.1215 is amended as follows:
0
a. By revising paragraphs (e)(2)(i)(B), (e)(2)(i)(C), and (e)(2)(i)(D).
0
b. By adding paragraph (e)(3).


Sec.  63.1215  What are health-based compliance alternatives for total 
chlorine?

* * * * *
    (e) * * *
    (2) * * *
    (i) * * *
    (B) Your permitting authority should notify you of approval or 
intent to disapprove your eligibility demonstration within 6 months 
after receipt of the original demonstration, and within 3 months after 
receipt of any supplemental information that you submit. A notice of 
intent to disapprove your eligibility demonstration, whether before or 
after the compliance date, will identify incomplete or inaccurate 
information or noncompliance with prescribed procedures and specify how 
much time you will have to submit additional information or to achieve 
the MACT standards for total chlorine under Sec. Sec.  63.1216, 
63.1217, 63.1219, 63.1220, and 63.1221. If your eligibility 
demonstration is disapproved, the permitting authority may extend the 
compliance date of the total chlorine standards up to one year to allow 
you to make changes to the design or operation of the combustor or 
related systems as quickly as practicable to enable you to achieve 
compliance with the MACT total chlorine standards.
    (C) If your permitting authority has not approved your eligibility 
demonstration by the compliance date, and has not issued a notice of 
intent to disapprove your demonstration, you may begin complying, on 
the compliance date, with the HCl-equivalent emission rate limits you 
present in your eligibility demonstration provided that you have made a 
good faith effort to provide complete and accurate information and to 
respond to any requests for additional information in a timely manner. 
If the permitting authority believes that you have not made a good 
faith effort to provide complete and accurate information or to respond 
to any requests for additional information, however, the authority may 
notify you in writing by the compliance date that you have not met the 
conditions for complying with the health-based compliance alternative 
without prior approval. Such notice will explain the basis for 
concluding that you have not made a good faith effort to comply with 
the health-based compliance alternative by the compliance date.
    (D) If your permitting authority issues a notice of intent to 
disapprove your eligibility demonstration after the compliance date, 
the authority will identify the basis for that notice and specify how 
much time you will have to submit additional information or to comply 
with the MACT standards for total chlorine under Sec. Sec.  63.1216, 
63.1217, 63.1219, 63.1220, and 63.1221. The permitting authority may 
extend the compliance date of the total chlorine standards up to one-
year to allow you to make changes to the design or operation of the 
combustor or related systems as quickly as practicable to enable you to 
achieve compliance with the MACT standards for total chlorine.
* * * * *
    (3) The operating requirements in the eligibility demonstration are 
applicable requirements for purposes of parts 70 and 71 of this chapter 
and will be incorporated in the title V permit.
* * * * *

0
6. Section 63.1219 is amended by revising paragraph (b)(7) to read as 
follows:


Sec.  63.1219   What are the replacement standards for hazardous waste 
incinerators?

* * * * *
    (b) * * *
    (7) Except as provided by paragraph (e) of this section, 
particulate matter emissions in excess of 0.0016 gr/dscf corrected to 7 
percent oxygen.
* * * * *

0
7. Section 63.1220 is amended by removing paragraphs (a)(2)(iii) and 
(b)(2)(iii) and revising paragraph (b)(7) to read as follows.


Sec.  63.1220  What are the replacement standards for hazardous waste 
burning cement kilns?

* * * * *
    (b) * * *
    (7) For particulate matter, both:
    (i) Emissions in excess of 0.0069 gr/dscf corrected to 7 percent 
oxygen; and
    (ii) Opacity greater than 20 percent, unless your source is 
equipped with a bag leak detection system under Sec.  63.1206(c)(8) or 
a particulate matter detection system under Sec.  63.1206(c)(9).
* * * * *
 [FR Doc. E8-25166 Filed 10-27-08; 8:45 am]

BILLING CODE 6560-50-P
