
 From:
Keith Barnett/RTP/USEPA/US
 To:
"O'Hare, Andrew" <AOhare@cement.org>
 Cc:
Leonard Lazarus/DC/USEPA/US@EPA
 Date:
10/26/2010 10:51 PM
 Subject:
RE: Cement Correction Notice


Yes I was talking about the calibration issue.  I think the compliance date for those requirements would require an opinion from OECA because we do specifically call out "compliance dates" in the section that discuss calibrations for feed or clinker rates, though we don't call then by that name.  But we also say three years for all requirements in the compliance date section.

However, we think that there is enough interpretative leeway in the term calibration that this should not cause a problem in the near term.  It does need to be addressed with some of the other testing and monitoring issues.  And we are not comfortable with addressing this in the clarification notice.  It would be better addressed through notice and comment rulemaking.

Keith W. Barnett
USEPA/OAQPS/SPPD/MMG
Mail Code D243-02
Research Triangle Park, NC  27711
919-541-5605
barnett.keith@epa.gov



 From:
O'Hare, Andrew <AOhare@cement.org>
 To:
Keith Barnett/RTP/USEPA/US@EPA
 Date:
10/25/2010 03:24 PM
 Subject:
RE: Cement Correction Notice



Keith, 

Thank you.  The last part of your message is a bit confusing.  Is it in reference to my question about the clinker production monitoring issues?  Is it safe to assume that the deadline for compliance with these requirements is 9-9-13?

Thanks,
Andy 

Andrew T. O'Hare, CAE
Vice President, Regulatory Affairs
Portland Cement Association
500 New Jersey, Avenue, NW
Washington, DC 20001
Phone: (202) 408-9494
Fax: (202) 408-0877
Cell: (202) 270-0094
e-mail: aohare@cement.org


-----Original Message-----
From: Barnett.Keith@epamail.epa.gov [mailto:Barnett.Keith@epamail.epa.gov] 
Sent: Monday, October 25, 2010 2:15 PM
To: O'Hare, Andrew
Subject: RE: Cement Correction Notice

I think I sent the wrong table.  Here is the corrected version.

(See attached file: Table 2.docx)

Steve Silverman and I discussed this issue with Hector. (We called Hector because he was the first person to raise the issue and had already sent information).  As a result of that conversation Steve and I believe this can be dealt with as more of an interpretative issue as to the meaning of calibration, and don't believe is would be a good idea to try and address this in the technical correction notice.

Keith W. Barnett
USEPA/OAQPS/SPPD/MMG
Mail Code D243-02
Research Triangle Park, NC  27711
919-541-5605
barnett.keith@epa.gov


|------------>
| From:      |
|------------>
  >--------------------------------------------------------------------------------------------------------------------------------------|
  |O'Hare, Andrew <AOhare@cement.org>                                                                                                    |
  >--------------------------------------------------------------------------------------------------------------------------------------|
|------------>
| To:        |
|------------>
  >--------------------------------------------------------------------------------------------------------------------------------------|
  |Keith Barnett/RTP/USEPA/US@EPA                                                                                                        |
  >--------------------------------------------------------------------------------------------------------------------------------------|
|------------>
| Date:      |
|------------>
  >--------------------------------------------------------------------------------------------------------------------------------------|
  |10/25/2010 12:00 PM                                                                                                                   |
  >--------------------------------------------------------------------------------------------------------------------------------------|
|------------>
| Subject:   |
|------------>
  >--------------------------------------------------------------------------------------------------------------------------------------|
  |RE: Cement Correction Notice                                                                                                          |
  >--------------------------------------------------------------------------------------------------------------------------------------|





Keith,

Thank for the opportunity to review.  Table 2 is still missing the opacity standard (20) under items 1 and 2.  Otherwise, the preamble and rule text are clear to me.

Do you plan to also clarify the compliance deadline language addressing the clinker production monitoring provisions in Sections 63.1350(d)(2) and 60.63(b)(2)?

Thanks,
Andy



Andrew T. O'Hare, CAE
Vice President, Regulatory Affairs
Portland Cement Association
500 New Jersey, Avenue, NW
Washington, DC 20001
Phone: (202) 408-9494
Fax: (202) 408-0877
Cell: (202) 270-0094
e-mail: aohare@cement.org

-----Original Message-----
From: Barnett.Keith@epamail.epa.gov [
mailto:Barnett.Keith@epamail.epa.gov]
Sent: Monday, October 25, 2010 10:37 AM
To: O'Hare, Andrew
Cc: silverman.steven@epamail.epa.gov
Subject: Cement Correction Notice


Dear Andy:

I made corrections to the notice language based on comments.  Please check this over again.

(See attached file: Cement Corrections for PCA-10-22.docx)

Still working on the schedule.

Keith W. Barnett
USEPA/OAQPS/SPPD/MMG
Mail Code D243-02
Research Triangle Park, NC  27711
919-541-5605
barnett.keith@epa.gov




