[Federal Register Volume 88, Number 37 (Friday, February 24, 2023)]
[Rules and Regulations]
[Pages 12108-12131]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2023-03683]



[[Page 12107]]

Vol. 88

Friday,

No. 37

February 24, 2023

Part III





Department of Commerce





-----------------------------------------------------------------------





Bureau of Industry and Security





-----------------------------------------------------------------------





15 CFR Parts 734, 740, 742, et al.





Implementation of 2021 Wassenaar Arrangement Decisions; Final Rule

  Federal Register / Vol. 88 , No. 37 / Friday, February 24, 2023 / 
Rules and Regulations  

[[Page 12108]]


-----------------------------------------------------------------------

DEPARTMENT OF COMMERCE

Bureau of Industry and Security

15 CFR Parts 734, 740, 742, 772 and 774

[Docket No. 221019-0222]
RIN 0694-AI72


Implementation of 2021 Wassenaar Arrangement Decisions

AGENCY: Bureau of Industry and Security, Commerce.

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: The Bureau of Industry and Security (BIS) maintains, as part 
of its Export Administration Regulations (EAR), the Commerce Control 
List (CCL), which identifies certain items subject to Department of 
Commerce jurisdiction. During the December 2021 Wassenaar Arrangement 
on Export Controls for Conventional Arms and Dual-Use Goods and 
Technologies (WA) Plenary meeting, Participating States of the WA 
(Participating State) made certain decisions affecting the WA control 
lists, which BIS is now implementing via amendments to the CCL. On 
August 15, 2022, BIS published a final rule that implemented some of 
these decisions by adding to the CCL four technologies that met the 
criteria for emerging or foundational technologies under Section 1758 
of the Export Control Reform Act of 2018 (ECRA). This final rule 
implements the remaining controls agreed to during the December 2021 WA 
Plenary meeting by revising the CCL, as well as certain EAR provisions, 
including License Exception Adjusted Peak Performance (APP). This final 
rule also makes corrections to align the scope of Significant Item (SI) 
license requirements throughout the EAR and makes a revision to License 
Exception Strategic Trade Authorization (STA).

DATES: This rule is effective February 24, 2023 except for the 
amendments to Sec.  740.7(d)(3)(i) and (ii) (instruction 5) and to 
supplement no. 1 to part 774 ECCNs 4A003, 4D001, and 4D001 (instruction 
13), which are effective March 14, 2023.

FOR FURTHER INFORMATION CONTACT: For general questions, contact Sharron 
Cook, Office of Exporter Services, Bureau of Industry and Security, 
U.S. Department of Commerce at 202-482-2440 or by email: 
[email protected].

For Technical Questions Contact

Categories 0, 1 & 2: Sean Ghannadian at 202-482-3429 or 
[email protected]
Category 3: Carlos Monroy at 202-482-3246 or [email protected]
Categories 4 & 5: Aaron Amundson or Anita Zinzuvadia 202-482-0707 or 
[email protected] or [email protected]
Categories 6: John Varesi at 202-482-1114 or [email protected]
Categories 7: David Rosenberg at 202-482-5987, John Varesi at 202-482-
1114 or [email protected] or [email protected]
Category 9: David Rosenberg at 202-482-5987 or 
[email protected] ``600 Series'' (munitions items): Jeffrey 
Leitz at 202-482-7417 or [email protected]

SUPPLEMENTARY INFORMATION:

Background

    The WA (http://www.wassenaar.org/) is a group of 42 like-minded 
states committed to promoting responsibility and transparency in the 
global arms trade and preventing destabilizing accumulations of 
conventional weapons. As a Participating State of the WA, the United 
States has committed to controlling for export all items on the WA's 
List of Dual-Use Goods and Technologies (WA Dual-Use List) and on the 
WA Munitions List (together, WA control lists). The WA control lists 
were first established in 1996 and have been revised annually 
thereafter. Participating States have agreed to implement the changes 
to the WA control lists as soon as possible after agreed upon by the WA 
Plenary. The United States' implementation of WA control list changes 
ensures that U.S. companies have a level playing field with their 
competitors in other Participating States.
    BIS published an interim final rule on August 15, 2022 (87 FR 
49979), implementing four new controls on items meeting the criteria of 
Section 1758 of ECRA, which were part of the revisions to the WA 
control lists decided by Participating States at the December 2021 WA 
Plenary meeting. The changes to the CCL and related EAR parts made by 
this rule reflect the remaining revisions to the WA control lists 
decided during the December 2021 WA Plenary meeting. The rule also 
makes related clarifying edits to CCL entries and revisions to reflect 
technical advancements. Unless explicitly discussed below, the 
revisions made by this rule will not impact the number of license 
applications submitted to BIS.

Revisions to the Commerce Control List Related to WA 2021 Plenary 
Meeting Decisions

    Revises (16) ECCNs: 1A613, 1C006, 2E003, 3A001, 3A002, 4A003, 
4D001, 4E001, 5A003, 6A005, 6A008, 6D003, 7D003, 9A004, 9B001, and 
9E003.
    Removed (1) ECCN: 0A988.

0A988 Conventional Military Steel Helmets

    In a rule issued on January 2, 2014 (79 FR 264), effective July 1, 
2014, BIS moved conventional steel helmets from ECCN 0A988 to newly 
added ECCN 1A613.y.1. ECCN 0A988 remained on the CCL but contained only 
a brief explanation that the control for these helmets had been moved 
to 1A613.y.1. Given the time that has elapsed since relocation of the 
control for these helmets, the explanation under paragraph 0A988, along 
with the entry itself, are no longer necessary. BIS is therefore 
removing ECCN 0A988 from the CCL.

1A613 Armored and Protective ``Equipment'' and Related Commodities

    This rule revises 1A613.c ``military helmets'' by removing the 
phrase ``and ``specially designed'' helmet shells, liners, or comfort 
pads therefor.'', because it is duplicative of items that are already 
controlled under 1A613.x, specifically, any specially designed parts, 
components, or accessories would be controlled under 1A613.x, including 
the shells, liners, and pads currently specified in 1A613.c. In 
paragraph 1A613.c, this rule adds Note 3, which lists characteristics 
of items that are not controlled by 1A613.c, e.g., first manufactured 
before 1970. The same language is added as a note to 1A613.y.1. The 
note below 1A613.x, which addresses examples of items controlled by 
this ECCN, is revised to improve readability.

1C006 Fluids and Lubricating Materials

    This rule revises 1C006.b by removing paragraph b.2 (Fluorinated 
silicone fluids), because extensive market research submitted to the WA 
indicates that in the past two decades countries that are not 
Participating States have either developed or obtained the expertise to 
produce fluorinated silicone fluids. Due to the availability of this 
item in countries that are not Participating States, the Participating 
States decided to remove it from their control lists. BIS is 
accordingly removing the item from the CCL. Items previously controlled 
under 1C006.b.2 are now EAR99 and remain subject to the EAR.

Annex to Category 1--List of Explosives (See ECCNs 1A004 and 1A008)

    This rule revises the Annex to Category 1 of the CCL by adding two

[[Page 12109]]

explosives under two entries, numbers 51 and 52, to the List of 
Explosives: EDNA (Ethylenedinitramine) (CAS 505-71-5); and TKX-50 
(Dihydroxylammonium 5,5'-bistetrazole-1,1'-diolate). These two 
explosives were added in 2017 and 2018, respectively, to the WA 
Munitions List (ML 8.a.), and were added for consistency's sake to the 
List of Explosives set forth in the Annex of Category 1 of the WA 
Munitions List as part of the December 2021 WA Plenary. TKX-50 
(Dihydroxylammonium 5,5'-bistetrazole-1,1'-diolate) is a high energetic 
material that outperforms numerous common explosives widely used today. 
For this reason, it was added to the WA Munitions List in 2018. EDNA is 
a legacy explosive standardized as a military explosive during World 
War II. EDNA has been studied in several countries but due to its lower 
energetic properties, it is not yet in full-scale use. Nevertheless, 
because EDNA has great potential for gun propellants applications, it 
was added to the WA Munitions List in 2017.

2E003 Other ``Technology''

    This rule removes 2E003.b.2 (Technical data consisting of process 
methods) from the CCL. The control on the parameters described in 
2E003.b.2 has remained unchanged since the establishment of the WA 
Dual-Use List in 1996. Since that date, each of the four processes 
described in 2E003.b.2.a-d. have entered common commercial use, e.g., 
golf clubs and automobile manufacturing. Therefore, there is no longer 
a reason to control the technical data specified in 2E003.b.2. on the 
CCL. This rule also deletes a note in the CCL related to one of the 
technologies in 2E003.b.2 and adds a nota bene (N.B.) regarding gas 
turbine engines.

Category 3--Electronics Notes

    This rule revises Note 1 to Category 3 by adding 3A001.b.12 to the 
list of 3A001 subparagraphs that are not within the scope of the note, 
i.e., if a 3A001.b.12 item is specially designed for or has the same 
functional characteristics as other equipment, then it remains 
classified as 3A001.b.12.

3A001 Electronic Items & 3A002 General Purpose ``Electronic 
Assemblies,'' Modules and Equipment

    This rule amends paragraph 3A001.b.4.b.1 by correcting the 
specified power output in decibel-milliwatts (dBm) from 48.54 dBm to 
48.45 dBm. It also makes two additional technical corrections by adding 
``a'' in 3A002.c.2 before ``Displayed Average Noise Level'' and in 
3A002.d.4 before ``single sideband''.
    This rule revises paragraphs 3A001.b.11.e (`frequency synthesizer' 
``electronic assemblies''), 3A002.d.3.e (signal generators with 
specified ``frequency switching times''), and 3A002.d.5.c (signal 
generators with specified `RF modulation bandwidth' of digital baseband 
signals) by decreasing the upper limit of the specified frequency range 
from 90 gigahertz (GHz) to 75 GHz. The upper limit of 75 GHz now 
applies to 3A001.b.11.e, 3A002.d.3.e, and 3A002.d.5.c, which have a 
``frequency switching time'' of ``less than 100 [mu]s for any frequency 
change exceeding 2.2 GHz.''
    The Participating States decided to expand certain frequency ranges 
to account for higher signal generator Radio Frequency (RF) modulation 
bandwidth at millimeter-wave frequencies, specifically within the 60 to 
90 GHz band (E-band), required for automotive anti-collision radar. 
Specifically, the 76 to 81 GHz frequency band has been allocated for 
automotive radar in the United States and Europe. Moreover, electronic 
assemblies and signal generator requirements for automotive radar 
millimeter-wave applications will require RF modulated outputs over a 
bandwidth larger than the former control limit of 2.2 GHz RF modulation 
bandwidth.
    Accordingly, 3A001.b.11.f is added as a new paragraph to control 
`frequency synthesizer' ``electronic assemblies'' having a ``frequency 
switching time'' of ``less than 100 [micro]s for any frequency change 
exceeding 5.0 GHz within the synthesized frequency range exceeding 75 
GHz but not exceeding 90 GHz.'' This rule also adds paragraph 
3A002.d.3.g to control signal generators having a ``frequency switching 
time'' of ``Less than 100 [micro]s for any frequency change exceeding 
5.0 GHz within the frequency range exceeding 75 GHz but not exceeding 
90 GHz;'' and adds paragraph 3A002.d.5.d to control signal generators 
with a `RF modulation bandwidth' of digital baseband signals 
``Exceeding 5.0 GHz within the frequency range exceeding 75 GHz but not 
exceeding 90 GHz.''

4A003 ``Digital Computers''

    Prior to the publication of this rule, 4A003.b specified an APP 
threshold of 29 Weighted TeraFLOPS (WT) for ``digital computers''. 
However, for those Participating States that manufacture digital 
computer systems, including 32-socket servers that have approached this 
29 WT threshold, such digital computer systems would likely exceed this 
APP threshold if built with the latest generation microprocessor in 
2022 or in the near future. Additionally, there is an increased demand 
for database servers across a broad range of industries including 
business planning, banking/financial transactions, healthcare, genetic 
research, and fraud detection. To reflect these circumstances, the 
Participating States decided to raise the control threshold from 29 WT 
to 70 WT. The Participating States determined that this increase in 
control threshold would provide sufficient margin for a few years' 
growth before another adjustment would be necessary.
    Accordingly, this rule raises the APP threshold for ``digital 
computers'' in 4A003.b from ``exceeding 29 Weighted TeraFLOPS (WT)'' to 
``exceeding 70 Weighted TeraFLOPS (WT).'' Consistent with this change, 
the Antiterrorism (AT) license requirement paragraph in the License 
Requirements section of 4A003 and the Note that follows the license 
requirement table are also amended by changing the specified APP 
threshold from 29 to 70 WT. The Congressional notification requirement 
set forth in subsection 1211(d) of the National Defense Authorization 
Act for Fiscal Year 1998 (Pub. L. 105-85, November 18, 1997, 111 Stat. 
1629, 1932-1933, as amended; 50 U.S.C. 4604 note) provides that the 
President must submit a report to Congress 60 days before adjusting the 
composite theoretical performance level above which exports of digital 
computers to Tier 3 countries require a license. The submission of this 
report has been delegated to the Secretary of Commerce. On January 13, 
2023, the Secretary of Commerce submitted to Congress a report that 
establishes and provides justification for the 70 WT control level 
using the APP formula. Therefore, this revision will become effective 
on March 14, 2023. BIS estimates that this revision will result in no 
change to license application submissions, because this revision is 
keeping pace with advancements in HPC technology.
    This rule makes a correction by removing 4A003.e from the national 
security license requirements, because there currently is no paragraph 
4A003.e.

4D001 ``Software'' & 4E001 ``Technology''

    In light of the change made to the APP threshold in 4A003.b, this 
rule makes conforming changes to the APP threshold in the License 
Exception Technology and Software under Restriction (TSR) eligibility 
paragraph and to the Special Conditions for STA paragraph under ECCNs 
4D001 and 4E001 that raise the specified APP threshold from 29 WT to 70 
WT. These

[[Page 12110]]

revisions will become effective on March 14, 2023.

Sec.  740.7 License Exception Adjusted Peak Performance (APP)

    This rule amends License Exception APP to raise the APP eligibility 
levels for deemed exports of ``technology'' and ``software'' source 
code destined to foreign nationals of Computer Tiers 1 and 3 Countries. 
These levels, which are recommended by industry groups in consultation 
with BIS, are raised to better enable the advancement of 
``development,'' ``production,'' and ``use'' ``technology'' and 
``software'' in the area of computer manufacturing, which in turn 
promotes advancements in military technology that bolster the national 
security of the United States.

Computer Tier 1 Revisions

    This rule amends Sec.  740.7(c)(3)(ii) by raising the APP from 40 
WT to 175 WT for eligible deemed exports of ``development'' and 
``production'' technology and source code to foreign nationals of Tier 
1 countries. It also amends Sec.  740.7(c)(3)(iii) by raising the APP 
from 200 WT to 500 WT for eligible deemed exports of ``use'' technology 
and source code to foreign nationals of Computer Tier 1 countries.

Computer Tier 3 Revisions

    This rule amends Sec.  740.7(d)(3)(i) by raising the APP from 16 WT 
to 50 WT for eligible deemed exports of ``development'' and 
``production'' technology and source code to foreign nationals of Tier 
3 countries. It also amends Sec.  740.7(d)(3)(ii) by raising the APP 
from 32 WT to 140 WT for eligible deemed exports of ``use'' technology 
and source code to foreign nationals of Computer Tier 3 countries which 
becomes effective March 14, 2023.

License Exception Strategic Trade Authorization Revision

    This rule adds new paragraph (b)(2)(viii)(A) to Sec.  740.20 
License Exception Strategic Trade Authorization (STA) to harmonize this 
license exception with the STA special condition under ECCN 9B001 that 
states that STA may not be used for a Country Group A:6 destination. 
Consistent with this addition, this rule redesignates existing 
subparagraphs (A)-(F) as (B)-(G). This revision to STA aligns with 
BIS's goal to clarify restrictions on the availability of STA for the 
export, reexport, and transfer (in-country) of certain items controlled 
under the EAR as set forth in the preamble of a proposed rule published 
on October 22, 2021 (86 FR 58615). This revision is also generally 
responsive to a public comment received in response to that rule that 
is supportive of BIS's efforts to clarify restrictions on STA's 
availability. BIS is reviewing other public comments that it received 
in response to that rule and will address them in a separate final rule 
at a future date.
    As set forth below, this rule also makes certain revisions to ECCN 
9B001.

5A003 ``Systems,'' ``Equipment'' and ``Components,'' for Non-
Cryptographic ``Information Security''

    This rule revises 5A003.a to replace the word ``using'' with the 
words ``to use,'' to clarify that the scope of controls applies to 
communication cable systems that were designed or modified to employ 
either mechanical, electrical or electronic means to detect 
surreptitious intrusion, not communication cable systems that were 
designed or modified by utilizing mechanical, electrical or electronic 
means.

6A005 ``Lasers'', ``Components'' and Optical Equipment

    6A005.d.1.b.1 applies to individual `multiple-transverse mode' 
semiconductor ``lasers'' with an average or continuous wave (CW) output 
power exceeding 15 watts (W). This is a relatively low output power 
value. Multiple-transverse mode semiconductor lasers can achieve much 
higher powers and are now readily available outside of Participating 
States in an increasing number of commercial applications. For this 
reason, this rule revises 6A005.d.1.b.1 by increasing the average or CW 
output power from 15 W to 25 W for individual `multiple-transverse 
mode' semiconductor ``lasers.''

6A008 Radar Systems, Equipment and Assemblies

    This rule revises Technical Note 1, which appears after the Note to 
6A008.l, by replacing the word ``used'' with the word ``designed'' to 
clarify that the scope of the note applies to marine radars that are 
designed for civil application rather than to marine radars used for 
civil application.

6D003 Other ``Software''

    This rule revises 6D003.h.1, which refers to certain Air Traffic 
Control ``software application programs'', by deleting the words 
``application programs,'' which are superfluous in this context. The 
word ``software'' sufficiently describes the scope of controlled under 
6D003.h.1.

7D003 Other ``Software''

    This rule makes an editorial revision to 7D003.e by adding a hyphen 
between the words ``circulation'' and ``controlled'' that appears after 
the word helicopter; as revised, the reference is to ``helicopter 
circulation-controlled anti-torque or circulation-controlled direction 
control systems,'' which is a defined term in Sec.  772.1 of the EAR.

9A004 Space Launch Vehicles and ``Spacecraft,'' ``Spacecraft Buses'', 
``Spacecraft Payloads'', ``Spacecraft'' On-Board Systems or Equipment, 
Terrestrial Equipment, and Air-Launch Platforms

    This rule adds ``sub-orbital craft'' to the heading of ECCN 9A004 
and to paragraph 9A004.g. Based on this addition, 9A004.g now controls 
``aircraft'' ``specially designed'' or modified to be air-launch 
platforms for ``sub-orbital craft.'' This change is being made to 
reflect the fact that ``aircraft'' ``specially designed'' or modified 
to be air-launch platforms for sub-orbital craft may be 
indistinguishable from ``aircraft'' ``specially designed'' or modified 
to be air-launch platforms for space launch vehicles.

9B001 Manufacturing Equipment, Tooling or Fixtures

    This rule revises 9B001.c by broadening the control in two 
respects. First, it replaces ``specially designed'' with ``designed'', 
and second, it replaces the phrase ``manufacturing gas turbine engine 
blades, vanes or ``tip shrouds'' '' with ``superalloys'', a broader 
term referring to certain highly durable materials. As revised, the 
text mirrors the control in 9B001.a, which covers directional 
solidification or single crystal casting equipment designed for 
``superalloys.'' In particular, the revised control focuses on 
additive-manufacturing equipment designed to work with a certain type 
of material (``superalloys''), rather than on the three manufactured 
items (``manufacturing gas turbine engine blades, vanes or ``tip 
shrouds'' ''). These changes are necessary to keep pace with technology 
advancements and modernize controls to address new methods to 
manufacture gas turbine engine components (e.g., blades, vanes, ``tip 
shrouds'') using refractory metals.

9E003 Other ``technology''

    This rule revises the STA special conditions paragraph for ECCN 
9E003 by removing paragraph a.8, and adding paragraphs .c and. i (other 
than technology for fan or power turbines) to match the STA limitation 
paragraph in Sec.  740.20(b)(2)(viii)(D)(1) of the EAR. This revision 
is consistent with BIS's goal, as stated in the preamble of the October 
22, 2021 rule (86 FR 58615), to

[[Page 12111]]

clarify restrictions on the availability of STA for the export, 
reexport, and transfer (in-country) of certain items controlled under 
the EAR.
    This rule also makes an editorial revision to 9E003.a.5 by removing 
a hyphen; as revised, the control applies to ``tip shrouds.''

Significant Items: Hot Section Technology

    A hot section refers to the portion of a gas turbine engine that 
operates at a high temperature, i.e., the combustion, turbine, and 
exhaust sections. This rule makes a correction to the list of items 
included as Significant Items (SI) in Sec. Sec.  734.4(a)(4)'s de 
minimis rules and in 742.14(a) and (b). The list included 9E003.j wing-
folding systems, which is not hot section technology, but did not 
include 9E003.k, `` ``Technology'' not otherwise controlled in 
9E003.a.1 through a.8, a.10, and .h and used in the ``development'', 
``production'', or overhaul of hot section ``parts'' or ``components'' 
of civil derivatives of military engines controlled on the USML.'' This 
revision will align these corrected sections of the EAR with the SI 
license requirements in 9E003.

Part 772--Definitions of Terms

    This rule amends Sec.  772.1 by revising the definitions of the 
terms ``compensation systems'' and ``diffusion bonding.'' The 
definition of ``compensation systems'' is clarified by adding the word 
``the'' in the phrase ``that permit reduction of [the] rigid body 
rotation noise of the platform.'' The definition of the term 
``diffusion bonding'' is amended by removing the reference to Category 
9 in the parenthetical that lists where this term is used in the CCL, 
because it is not used in Category 9.

Savings Clause

    Shipments of items removed from license exception eligibility or 
eligibility for export, reexport or transfer (in-country) without a 
license as a result of this regulatory action that were on dock for 
loading, on lighter, laden aboard an exporting carrier, or en route 
aboard a carrier to a port of export, on February 24, 2023, pursuant to 
actual orders for exports, reexports and transfers (in-country) to a 
foreign destination, may proceed to that destination under the previous 
license exception eligibility or without a license so long as they have 
been exported, reexported or transferred (in-country) before April 18, 
2023. Any such items not actually exported, reexported or transferred 
(in-country) before midnight, on April 18, 2023, require a license in 
accordance with this final rule.

Export Control Reform Act of 2018

    On August 13, 2018, the President signed into law the John S. 
McCain National Defense Authorization Act for Fiscal Year 2019, which 
included the ECRA, 50 U.S.C. 4801-4852. ECRA provides the legal basis 
for BIS's principal authorities and serves as the authority under which 
BIS issues this rule.

Rulemaking Requirements

    1. Executive Orders 13563 and 12866 direct agencies to assess all 
costs and benefits of available regulatory alternatives and, if 
regulation is necessary, to select regulatory approaches that maximize 
net benefits (including potential economic, environmental, public 
health and safety effects and distributive impacts and equity). 
Executive Order 13563 emphasizes the importance of quantifying both 
costs and benefits and of reducing costs, harmonizing rules, and 
promoting flexibility.
    This final rule has been designated a ``significant regulatory 
action'' under section 3(f) of Executive Order 12866. This rule does 
not contain policies with Federalism implications as that term is 
defined under Executive Order 13132.
    2. Notwithstanding any other provision of law, no person is 
required to respond to, nor shall any person be subject to a penalty 
for failure to comply with, a collection of information subject to the 
requirements of the Paperwork Reduction Act of 1995 (44 U.S.C. 3501 et 
seq.) (PRA), unless that collection of information displays a currently 
valid Office of Management and Budget (OMB) Control Number. Although 
this rule makes important changes to the EAR for items controlled for 
national security reasons, BIS believes that the overall increases in 
burdens and costs associated with the following information collections 
due to this rule will be minimal.
     0694-0088, ``Simplified Network Application Processing 
System,'' which carries a burden- hour estimate of 29.6 minutes for a 
manual or electronic submission;
     0694-0137, ``License Exceptions and Exclusions,'' which 
carries a burden-hour estimate average of 1.5 hours per submission 
(Note: submissions for License Exceptions are rarely required);
     0694-0096, ``Five Year Records Retention Period,'' which 
carries a burden-hour estimate of less than 1 minute; and
     0607-0152, ``Automated Export System (AES) Program,'' 
which carries a burden-hour estimate of 3 minutes per electronic 
submission.
    Additional information regarding these collections of information--
including all background materials--can be found at https://www.reginfo.gov/public/do/PRAMain and using the search function to 
enter either the title of the collection or the OMB Control Number.
    3. Pursuant to Section 1762 of ECRA (50 U.S.C. 4821), this action 
is exempt from the Administrative Procedure Act (APA) (5 U.S.C. 553) 
requirements for notice of proposed rulemaking, opportunity for public 
participation and delay in effective date.

List of Subjects

15 CFR Part 734

    Administrative practice and procedure, Exports, Inventions and 
patents, Research, Science and technology.

15 CFR Part 740

    Administrative practice and procedure, Exports, Reporting and 
recordkeeping requirements.

15 CFR Part 742

    Exports, Terrorism.

15 CFR Part 772

    Exports.

15 CFR Part 774

    Exports, Reporting and recordkeeping requirements, Terrorism.

    Accordingly, parts 734, 740, 742, 772 and 774 of the Export 
Administration Regulations (15 CFR parts 730-774) are amended as 
follows:

PART 734--SCOPE OF THE EXPORT ADMINISTRATION REGULATIONS

0
1. The authority citation for part 734 continues to read as follows:

    Authority:  50 U.S.C. 4801-4852; 50 U.S.C. 4601 et seq.; 50 
U.S.C. 1701 et seq.; E.O. 12938, 59 FR 59099, 3 CFR, 1994 Comp., p. 
950; E.O. 13020, 61 FR 54079, 3 CFR, 1996 Comp., p. 219; E.O. 13026, 
61 FR 58767, 3 CFR, 1996 Comp., p. 228; E.O. 13222, 66 FR 44025, 3 
CFR, 2001 Comp., p. 783; E.O. 13637, 78 FR 16129, 3 CFR, 2014 Comp., 
p. 223; Notice of November 10, 2021, 86 FR 62891 (November 12, 
2021).


0
2. Effective February 24, 2023, amend Sec.  734.4 by revising paragraph 
(a)(4) to read as follows:


Sec.  734.4  De minimis U.S. content.

    (a) * * *
    (4) There is no de minimis level for U.S.-origin technology 
controlled by

[[Page 12112]]

ECCN 9E003.a.1 through a.8, h, .i, and .k, when redrawn, used, 
consulted, or otherwise commingled abroad.
* * * * *

PART 740--LICENSE EXCEPTIONS

0
3. The authority citation for part 740 continues to read as follows:

    Authority:  50 U.S.C. 4801-4852; 50 U.S.C. 4601 et seq.; 50 
U.S.C. 1701 et seq.; 22 U.S.C. 7201 et seq.; E.O. 13026, 61 FR 
58767, 3 CFR, 1996 Comp., p. 228; E.O. 13222, 66 FR 44025, 3 CFR, 
2001 Comp., p. 783.


0
4. Effective February 24, 2023, amend Sec.  740.7 by revising 
paragraphs (c)(3)(ii) and (iii) to read as follows:


Sec.  740.7  COMPUTERS (APP).

* * * * *
    (c) * * *
    (3) * * *
    (ii) ``Development'' and ``production'' technology and source code 
described in paragraph (a)(2) of this section for computers with a APP 
less than or equal to 175 Weighted TeraFLOPS (WT) are eligible for 
deemed exports under License Exception APP to foreign nationals of Tier 
1 destinations, other than the destinations that are listed in 
paragraph (c)(3)(i) of this section, subject to the restrictions in 
paragraph (b) of this section.
    (iii) ``Use'' technology and source code described in paragraph 
(a)(2) of this section for computers with a APP less than or equal to 
500 WT are eligible for deemed exports under License Exception APP to 
foreign nationals of Tier 1 destinations, other than the destinations 
that are listed in paragraph (c)(3)(i) of this section, subject to the 
restrictions in paragraph (b) of this section.
* * * * *

0
5. Effective March 14, 2023, Sec.  740.7 is amended by revising 
paragraphs (d)(3)(i) and (ii) to read as follows:


Sec.  740.7  Computers (APP).

* * * * *
    (d) * * *
    (3) * * *
    (i) ``Development'' and ``production'' technology and source code 
described in paragraph (a)(2) of this section for computers with an APP 
less than or equal to 50 Weighted TeraFLOPs (WT) are eligible for 
deemed exports under License Exception APP to foreign nationals of Tier 
3 destinations as described in paragraph (d)(1) of this section, 
subject to the restrictions in paragraph (b) of this section.
    (ii) ``Use'' technology and source code described in paragraph 
(a)(2) of this section for computers with an APP less than or equal to 
140 WT are eligible for deemed exports under License Exception APP to 
foreign nationals of Tier 3 destinations as described in paragraph 
(d)(1) of this section, subject to the restrictions in paragraph (b) of 
this section.
* * * * *

0
6. Effective February 24, 2023, amend Sec.  740.20 by redesignating 
paragraphs (b)(2)(viii)(A) through (F) as paragraphs (b)(2)(viii)(B) 
through (G) and adding new paragraph (b)(2)(viii)(A) to read as 
follows:


Sec.  740.20  License Exception Strategic Trade Authorization (STA).

* * * * *
    (b) * * *
    (2) * * *
    (viii) * * *
    (A) License Exception STA may not be used for 9B001 when destined 
to a country in Country Group A:6.
* * * * *

PART 742--CONTROL POLICY--CCL BASED CONTROLS

0
7. The authority citation for part 742 continues to read as follows:

    Authority:  50 U.S.C. 4801-4852; 50 U.S.C. 4601 et seq.; 50 
U.S.C. 1701 et seq.; 22 U.S.C. 3201 et seq.; 42 U.S.C. 2139a; 22 
U.S.C. 7201 et seq.; 22 U.S.C. 7210; Sec. 1503, Pub. L. 108-11, 117 
Stat. 559; E.O. 12058, 43 FR 20947, 3 CFR, 1978 Comp., p. 179; E.O. 
12851, 58 FR 33181, 3 CFR, 1993 Comp., p. 608; E.O. 12938, 59 FR 
59099, 3 CFR, 1994 Comp., p. 950; E.O. 13026, 61 FR 58767, 3 CFR, 
1996 Comp., p. 228; E.O. 13222, 66 FR 44025, 3 CFR, 2001 Comp., p. 
783; Presidential Determination 2003-23, 68 FR 26459, 3 CFR, 2004 
Comp., p. 320; Notice of November 10, 2021, 86 FR 62891 (November 
12, 2021).


0
8. Effective February 24, 2023, amend Sec.  742.14 by revising 
paragraph (a) and paragraph (b) introductory text to read as follows:


Sec.  742.14  Significant items: hot section technology for the 
development, production or overhaul of commercial aircraft engines, 
components, and systems.

    (a) License requirement. Licenses are required for all 
destinations, except Canada, for ECCNs having an ``SI'' under the 
``Reason for Control'' paragraph. These items include hot section 
technology for the development, production or overhaul of commercial 
aircraft engines controlled under ECCN 9E003.a.1 through a.8, .h, .i 
and .k, and related controls.
    (b) Licensing policy. Pursuant to section 6 of the Export 
Administration Act of 1979, as amended, foreign policy controls apply 
to technology required for the development, production or overhaul of 
commercial aircraft engines controlled by ECCN 9E003a.1 through a.8, 
.h, .i, and .k, and related controls. These controls supplement the 
national security controls that apply to these items. Applications for 
export and reexport to all destinations will be reviewed on a case-by-
case basis to determine whether the export or reexport is consistent 
with U.S. national security and foreign policy interests. The following 
factors are among those that will be considered to determine what 
action will be taken on license applications:
* * * * *

PART 772--DEFINITIONS OF TERMS

0
9. The authority citation for part 772 continues to read as follows:

    Authority:  50 U.S.C. 4801-4852; 50 U.S.C. 4601 et seq.; 50 
U.S.C. 1701 et seq.; E.O. 13222, 66 FR 44025, 3 CFR, 2001 Comp., p. 
783.


0
10. Effective February 24, 2023, amend Sec.  772.1 by revising the 
definitions of ``compensation systems'' and ``diffusion bonding,'' to 
read as follows:


Sec.  772.1  Definitions of terms as used in the Export Administration 
Regulations (EAR).

* * * * *
    Compensation systems. (Cat 6) Consist of the primary scalar sensor, 
one or more reference sensors (e.g., vector ``magnetometers'') together 
with software that permit reduction of the rigid body rotation noise of 
the platform.
* * * * *
    Diffusion bonding. (Cat 1 and 2)--A solid state joining of at least 
two separate pieces of metals into a single piece with a joint strength 
equivalent to that of the weakest material, wherein the principal 
mechanism is interdiffusion of atoms across the interface.
* * * * *

PART 774--THE COMMERCE CONTROL LIST

0
11. The authority citation for part 774 continues to read as follows:

    Authority:  50 U.S.C. 4801-4852; 50 U.S.C. 4601 et seq.; 50 
U.S.C. 1701 et seq.; 10 U.S.C. 8720; 10 U.S.C. 8730(e); 22 U.S.C. 
287c, 22 U.S.C. 3201 et seq.; 22 U.S.C. 6004; 42 U.S.C. 2139a; 15 
U.S.C. 1824; 50 U.S.C. 4305; 22 U.S.C. 7201 et seq.; 22 U.S.C. 7210; 
E.O. 13026, 61 FR 58767, 3 CFR, 1996 Comp., p. 228; E.O. 13222, 66 
FR 44025, 3 CFR, 2001 Comp., p. 783.


0
12. Effective February 24, 2023, amend supplement no. 1 to part 774 by:
0
a. Under Category 0 removing ECCN 0A988;

[[Page 12113]]

0
b. Under Category 1 revising ECCNs 1A613, 1C006, and Annex to Category 
1;
0
c. Under Category 2 revising ECCN 2E003;
0
d. Under Category 3 revising Note 1, and ECCNs 3A001 and 3A002;
0
e. Under Category 5PT2 revising ECCN 5A003;
0
f. Under Category 6 revising ECCNs 6A005, 6A008, and 6D003;
0
g. Under Category 7 revising ECCN 7D003; and
0
h. Under Category 9, revising ECCNs 9A004, 9B001, and 9E003.
    The revisions read as follows:

Supplement No. 1 to Part 774--The Commerce Control List

* * * * *

Category 1--Special Materials and Related Equipment, Chemicals, 
``Microorganisms,'' and ``Toxins''

* * * * *
1A613 Armored and protective ``equipment'' and related commodities, 
as follows (see List of Items Controlled).

License Requirements

Reason for Control: NS, RS, AT, UN

 
                                            Country chart (see Supp. No.
                Control(s)                         1 to part 738)
 
NS applies to entire entry except 1A613.y.  NS Column 1.
RS applies to entire entry except 1A613.y.  RS Column 1.
RS applies 1A613.y........................  China, Russia, or Venezuela
                                             (see Sec.   742.6(a)(7)).
AT applies to entire entry................  AT Column 1.
UN applies to entire entry, except 1A613.y  See Sec.   746.1(b) for UN
                                             controls.
 

List Based License Exceptions (See Part 740 for a Description of All 
License Exceptions)

LVS: $1500
GBS: N/A

Special Conditions for STA

STA: Paragraph (c)(2) of License Exception STA (Sec.  740.20(c)(2) 
of the EAR) may not be used for any item in 1A613.

List of Items Controlled

Related Controls: (1) Defense articles, such as materials made from 
classified information, that are controlled by USML Category X or 
XIII of the ITAR, and technical data (including software) directly 
related thereto, are ``subject to the ITAR.'' (2) See ECCN 0A919 for 
foreign-made ``military commodities'' that incorporate more than a 
de minimis amount of US-origin ``600 series'' controlled content. 
(3) See ECCN 9A610.g for anti-gravity suits (``G-suits'') and 
pressure suits capable of operating at altitudes higher than 55,000 
feet above sea level. (4) For other military helmet ``components'' 
or ``accessories'' not specified in 1A613.c, see the relevant ECCN 
in the CCL or USML Entry.
Related Definitions: References to ``NIJ Type'' protection are to 
the National Institute of Justice Classification guide at NIJ 
Standard 0101.06, Ballistic Resistance of Body Armor, and NIJ 
Standard 0108.01, Ballistic Resistant Protective Materials.
Items:

    a. Metallic or non-metallic armored plate ``specially designed'' 
for military use and not controlled by the USML.
    Note to paragraph a: For controls on body armor plates, see ECCN 
1A613.d.2 and USML Category X(a)(1).
    b. Shelters ``specially designed'' to:
    b.1. Provide ballistic protection for military systems; or
    b.2. Protect against nuclear, biological, or chemical 
contamination.
    c. Military helmets (other than helmets controlled under 
1A613.y.1) providing less than NIJ Type IV or ``equivalent 
standards'' protection.
    Note 1: See ECCN 0A979 for controls on police helmets.
    Note 2: See USML Category X(a)(5) and (a)(6) for controls on 
other military helmets.
    Note 3: 1A613.c does not apply to helmets that meet all the 
following:
    a. Were first manufactured before 1970; and
    b. Are neither designed or modified to accept, nor equipped with 
items specified by the U.S. Munitions List (22 CFR 121) or another 
``600 series'' ECCN.
    d. Body armor and protective garments, as follows:
    d.1. Soft body armor and protective garments manufactured to 
military standards or specifications, or to their equivalents, that 
provide ballistic protection equal to or less than NIJ level III 
(NIJ 0101.06, July 2008) or ``equivalent standards''; or
    Note: For 1A613.d.1, military standards or specifications 
include, at a minimum, specifications for fragmentation protection.
    d.2. Hard body armor plates that provide ballistic protection 
equal to NIJ level III (NIJ 0101.06, July 2008) or ``equivalent 
standards''.
    Note: See ECCN 1A005 for controls on soft body armor not 
manufactured to military standards or specifications and hard body 
armor plates providing less than NIJ level III or ``equivalent 
standards'' protection. For body armor providing NIJ Type IV 
protection or greater, see USML Category X(a)(1).
    e. Atmospheric diving suits ``specially designed'' for rescue 
operations for submarines controlled by the USML or the CCL.
    f. Other personal protective ``equipment'' ``specially 
designed'' for military applications not controlled by the USML, not 
elsewhere controlled on the CCL.
    g. to w. [Reserved]
    x. ``Parts,'' ``components,'' ``accessories,'' and 
``attachments'' that are ``specially designed'' for a commodity 
controlled by ECCN 1A613 (except for 1A613.y) or an article 
enumerated in USML Category X, and not controlled elsewhere in the 
USML.
    Note: 1A613.x includes forgings, castings, and other unfinished 
products, such as extrusions and machined bodies, that have reached 
a stage in manufacturing where they are clearly identifiable by 
mechanical properties, material composition, geometry, or function 
as commodities specified in ECCN 1A613.x.
    y. Other commodities as follows:
    y.1 Conventional military steel helmets.
    Note: 1A613.y.1 does not apply to helmets that meet all the 
following:
    a. Were first manufactured before 1970; and
    b. Are neither designed or modified to accept, nor equipped with 
items specified by the U.S. Munitions List (22 CFR 121) or another 
``600 series'' ECCN.
    N.B. to paragraph y.1: For other military helmet ``components'' 
or ``accessories,'' see the relevant ECCN in the CCL or USML Entry.
    y.2 [Reserved]
* * * * *
1C006 Fluids and lubricating materials, as follows (see List of 
Items Controlled).

License Requirements

Reason for Control: NS, AT

 
                                            Country chart (see Supp. No.
                Control(s)                         1 to part 738)
 
NS applies to entire entry................  NS Column 2.
AT applies to entire entry................  AT Column 1.
 

List Based License Exceptions (See Part 740 for a Description of All 
License Exceptions)

LVS: $3000
GBS: Yes for 1C006.d

List of Items Controlled

Related Controls: See also 1C996.
Related Definitions: N/A
Items:

    a. [Reserved]
    b. Lubricating materials containing, as their principal 
ingredients, phenylene or alkylphenylene ethers or thio-ethers, or 
their mixtures, containing more than two ether or thio-ether 
functions or mixtures thereof.
    c. Damping or flotation fluids having all of the following:
    c.1. Purity exceeding 99.8%;
    c.2. Containing less than 25 particles of 200 [mu]m or larger in 
size per 100 ml; and
    c.3. Made from at least 85% of any of the following:
    c.3.a. Dibromotetrafluoroethane (CAS 25497-30-7, 124-73-2, 
27336-23-8);
    c.3.b. Polychlorotrifluoroethylene (oily and waxy modifications 
only); or
    c.3.c. Polybromotrifluoroethylene;
    d. Fluorocarbon fluids designed for electronic cooling and 
having all of the following:
    d.1. Containing 85% by weight or more of any of the following, 
or mixtures thereof:
    d.1.a. Monomeric forms of perfluoropolyalkylether-triazines or 
perfluoroaliphatic-ethers;
    d.1.b. Perfluoroalkylamines;
    d.1.c. Perfluorocycloalkanes; or
    d.1.d. Perfluoroalkanes;
    d.2. Density at 298 K (25 [deg]C) of 1.5 g/ml or more;

[[Page 12114]]

    d.3. In a liquid state at 273 K (0 [deg]C); and
    d.4. Containing 60% or more by weight of fluorine.
    Note: 1C006.d does not apply to materials specified and packaged 
as medical products.
* * * * *

Annex to Category 1

List of Explosives (See ECCNs 1A004 and 1A008)

    1. ADNBF (aminodinitrobenzofuroxan or 7 amino 4,6 
dinitrobenzofurazane 1 oxide) (CAS 97096 78 1);
    2. BNCP (cis bis (5 nitrotetrazolato) tetra amine cobalt (III) 
perchlorate) (CAS 117412 28 9);
    3. CL 14 (diamino dinitrobenzofuroxan or 5,7 diamino 4,6 
dinitrobenzofurazane 1 oxide) (CAS 117907 74 1);
    4. CL 20 (HNIW or Hexanitrohexaazaisowurtzitane) (CAS 135285 90 
4); chlathrates of CL 20;
    5. CP (2 (5 cyanotetrazolato) penta amine cobalt (III) 
perchlorate) (CAS 70247 32 4);
    6. DADE (1,1 diamino 2,2 dinitroethylene, FOX-7) (CAS 145250-81-
3);
    7. DATB (diaminotrinitrobenzene) (CAS 1630 08 6);
    8. DDFP (1,4 dinitrodifurazanopiperazine);
    9. DDPO (2,6 diamino 3,5 dinitropyrazine 1 oxide, PZO) (CAS 
194486 77 6);
    10. DIPAM (3,3' diamino 2,2',4,4',6,6' hexanitrobiphenyl or 
dipicramide) (CAS 17215 44 0);
    11. DNGU (DINGU or dinitroglycoluril) (CAS 55510 04 8);
    12. Furazans as follows:
    a. DAAOF (diaminoazoxyfurazan);
    b. DAAzF (diaminoazofurazan) (CAS 78644 90 3);
    13. HMX and derivatives, as follows:
    a. HMX (Cyclotetramethylenetetranitramine, octahydro 1,3,5,7 
tetranitro 1,3,5,7 tetrazine, 1,3,5,7 tetranitro 1,3,5,7 tetraza 
cyclooctane, octogen or octogene) (CAS 2691 41 0);
    b. Difluoroaminated analogs of HMX;
    c. K 55 (2,4,6,8 tetranitro 2,4,6,8 tetraazabicyclo [3,3,0] 
octanone 3, tetranitrosemiglycouril or keto bicyclic HMX) (CAS 
130256 72 3);
    14. HNAD (hexanitroadamantane) (CAS 143850 71 9);
    15. HNS (hexanitrostilbene) (CAS 20062 22 0);
    16. Imidazoles as follows:
    a. BNNII (Octahydro 2,5 bis(nitroimino)imidazo [4,5 
d]imidazole);
    b. DNI (2,4 dinitroimidazole) (CAS 5213 49 0);
    c. FDIA (1 fluoro 2,4 dinitroimidazole);
    d. NTDNIA (N (2 nitrotriazolo) 2,4 dinitroimidazole);
    e. PTIA (1 picryl 2,4,5 trinitroimidazole);
    17. NTNMH (1 (2 nitrotriazolo) 2 dinitromethylene hydrazine);
    18. NTO (ONTA or 3 nitro 1,2,4 triazol 5 one) (CAS 932 64 9);
    19. Polynitrocubanes with more than four nitro groups;
    20. PYX (2,6 Bis(picrylamino) 3,5 dinitropyridine) (CAS 38082 89 
2);
    21. RDX and derivatives, as follows:
    a. RDX (cyclotrimethylenetrinitramine, cyclonite, T4, hexahydro 
1,3,5 trinitro 1,3,5 triazine, 1,3,5 trinitro 1,3,5 triaza 
cyclohexane, hexogen or hexogene) (CAS 121 82 4);
    b. Keto RDX (K 6 or 2,4,6 trinitro 2,4,6 triazacyclohexanone) 
(CAS 115029 35 1);
    22. TAGN (triaminoguanidinenitrate) (CAS 4000 16 2);
    23. TATB (triaminotrinitrobenzene) (CAS 3058 38 6);
    24. TEDDZ (3,3,7,7 tetrabis(difluoroamine) octahydro 1,5 dinitro 
1,5 diazocine);
    25. Tetrazoles as follows:
    a. NTAT (nitrotriazol aminotetrazole);
    b. NTNT (1 N (2 nitrotriazolo) 4 nitrotetrazole);
    26. Tetryl (trinitrophenylmethylnitramine) (CAS 479 45 8);
    27. TNAD (1,4,5,8 tetranitro 1,4,5,8 tetraazadecalin) (CAS 
135877 16 6);
    28. TNAZ (1,3,3 trinitroazetidine) (CAS 97645 24 4);
    29. TNGU (SORGUYL or tetranitroglycoluril) (CAS 55510 03 7);
    30. TNP (1,4,5,8 tetranitro pyridazino[4,5 d]pyridazine) (CAS 
229176 04 9);
    31. Triazines as follows:
    a. DNAM (2 oxy 4,6 dinitroamino s triazine) (CAS 19899 80 0);
    b. NNHT (2 nitroimino 5 nitro hexahydro 1,3,5 triazine) (CAS 
130400 13 4);
    32. Triazoles as follows:
    a. 5 azido 2 nitrotriazole;
    b. ADHTDN (4 amino 3,5 dihydrazino 1,2,4 triazole dinitramide) 
(CAS 1614 08 0);
    c. ADNT (1 amino 3,5 dinitro 1,2,4 triazole);
    d. BDNTA ((bis dinitrotriazole)amine);
    e. DBT (3,3' dinitro 5,5 bi 1,2,4 triazole) (CAS 30003 46 4);
    f. DNBT (dinitrobistriazole) (CAS 70890 46 9);
    g. [Reserved]
    h. NTDNT (1 N (2 nitrotriazolo) 3,5 dinitrotriazole);
    i. PDNT (1 picryl 3,5 dinitrotriazole);
    j. TACOT (tetranitrobenzotriazolobenzotriazole) (CAS 25243 36 
1);
    33. ``Explosives'' not listed elsewhere in this list having a 
detonation velocity exceeding 8,700 m/s, at maximum density, or a 
detonation pressure exceeding 34 GPa (340 kbar);
    34. [Reserved]
    35. Nitrocellulose (containing more than 12.5% nitrogen) (CAS 
9004-70-0);
    36. Nitroglycol (CAS 628-96-6);
    37. Pentaerythritol tetranitrate (PETN) (CAS 78-11-5);
    38. Picryl chloride (CAS 88-88-0);
    39. 2,4,6 Trinitrotoluene (TNT) (CAS 118-96-7);
    40. Nitroglycerine (NG) (CAS 55-63-0);
    41. Triacetone Triperoxide (TATP) (CAS 17088-37-8);
    42. Guanidine nitrate (CAS 506-93-4);
    43. Nitroguanidine (NQ) (CAS 556 88 7);
    44. DNAN (2,4-dinitroanisole) (CAS 119-27-7);
    45. TEX (4,10-Dinitro-2,6,8,12-tetraoxa-4,10-
diazaisowurtzitane);
    46. GUDN (Guanylurea dinitramide) FOX-12 (CAS 217464-38-5);
    47. Tetrazines as follows:
    a. BTAT (Bis(2,2,2-trinitroethyl)-3,6-diaminotetrazine);
    b. LAX-112 (3,6-diamino-1,2,4,5-tetrazine-1,4-dioxide);
    48. Energetic ionic materials melting between 343 K (70 [deg]C) 
and 373 K (100 [deg]C) and with detonation velocity exceeding 6,800 
m/s or detonation pressure exceeding 18 GPa (180 kbar);
    49. BTNEN (Bis(2,2,2-trinitroethyl)-nitramine) (CAS 19836-28-3);
    50. FTDO (5,6-(3',4'-furazano)- 1,2,3,4-tetrazine-1,3-dioxide);
    51. EDNA (Ethylenedinitramine) (CAS 505-71-5);
    52. TKX-50 (Dihydroxylammonium 5,5'-bistetrazole-1,1'-diolate).

Category 2--Materials Processing

* * * * *
2E003 Other ``technology'', as follows (see List of Items 
Controlled).

License Requirements

Reason for Control: NS, AT

 
                                            Country chart (see Supp. No.
                Control(s)                         1 to part 738)
 
NS applies to entire entry................  NS Column 1.
AT applies to entire entry................  AT Column 1.
 

List Based License Exceptions (See Part 740 for a Description of All 
License Exceptions)

TSR: Yes, except 2E003.b, .e and .f

List of Items Controlled

Related Controls: See 2E001, 2E002, and 2E101 for ``development'' 
and ``use'' technology for equipment that are designed or modified 
for densification of carbon-carbon composites, structural composite 
rocket nozzles and reentry vehicle nose tips.
Related Definitions: N/A
Items:

    a. [Reserved]
    b. ``Technology'' for metal-working manufacturing processes, as 
follows:
    b.1. ``Technology'' for the design of tools, dies or fixtures 
``specially designed'' for any of the following processes:
    b.1.a. ``Superplastic forming'';
    b.1.b. ``Diffusion bonding''; or
    b.1.c. `Direct-acting hydraulic pressing';
    b.2. [Reserved]
    N.B.: For ``technology'' for metal-working manufacturing 
processes for gas turbine engines and components, see 9E003 and USML 
Category XIX.
    Technical Note: `Direct-acting hydraulic pressing' is a 
deformation process which uses a fluid-filled flexible bladder in 
direct contact with the workpiece.
    c. ``Technology'' for the ``development'' or ``production'' of 
hydraulic stretch-forming machines and dies therefor, for the 
manufacture of airframe structures;
    d. [Reserved]
    e. ``Technology'' for the ``development'' of integration 
``software'' for incorporation of expert systems for advanced 
decision support of shop floor operations into ``numerical control'' 
units;
    f. ``Technology'' for the application of inorganic overlay 
coatings or inorganic

[[Page 12115]]

surface modification coatings (specified in column 3 of the 
following table) to non-electronic substrates (specified in column 2 
of the following table), by processes specified in column 1 of the 
following table and defined in the Technical Note.
    N.B. This table should be read to control the technology of a 
particular `Coating Process' only when the resultant coating in 
column 3 is in a paragraph directly across from the relevant 
`Substrate' under column 2. For example, Chemical Vapor Deposition 
(CVD) `coating process' control the ``technology'' for a particular 
application of `silicides' to `Carbon-carbon, Ceramic and Metal 
``matrix'' ``composites'' substrates, but are not controlled for the 
application of `silicides' to `Cemented tungsten carbide (16), 
Silicon carbide (18)' substrates. In the second case, the resultant 
coating is not listed in the paragraph under column 3 directly 
across from the paragraph under column 2 listing `Cemented tungsten 
carbide (16), Silicon carbide (18)'.
* * * * *

Category 3--Electronics

A. ``End Items,'' ``Equipment,'' ``Accessories,'' ``Attachments,'' 
``Parts,'' ``Components,'' and ``Systems''

    Note 1: The control status of equipment and ``components'' 
described in 3A001 or 3A002, other than those described in 3A001.a.3 
to 3A001.a.10, 3A001.a.12 to 3A001.a.14, or 3A001.b.12, which are 
``specially designed'' for or which have the same functional 
characteristics as other equipment is determined by the control 
status of the other equipment.
* * * * *
3A001 Electronic items as follows (see List of Items Controlled).

Reason for Control: NS, RS, MT, NP, AT

 
                                            Country chart (see Supp. No.
                Control(s)                         1 to part 738)
 
NS applies to ``Monolithic Microwave        NS Column 1.
 Integrated Circuit'' (``MMIC'')
 amplifiers in 3A001.b.2 and discrete
 microwave transistors in 3A001.b.3,
 except those 3A001.b.2 and b.3 items
 being exported or reexported for use in
 civil telecommunications applications.
NS applies to entire entry................  NS Column 2.
RS applies ``Monolithic Microwave           RS Column 1.
 Integrated Circuit'' (``MMIC'')
 amplifiers in 3A001.b.2 and discrete
 microwave transistors in 3A001.b.3,
 except those 3A001.b.2 and b.3 items
 being exported or reexported for use in
 civil telecommunications applications.
MT applies to 3A001.a.1.a when usable in    MT Column 1.
 ``missiles''; and to 3A001.a.5.a when
 ``designed or modified'' for military
 use, hermetically sealed and rated for
 operation in the temperature range from
 below -54 [deg]C to above +125 [deg]C.
NP applies to pulse discharge capacitors    NP Column 1.
 in 3A001.e.2 and superconducting
 solenoidal electromagnets in 3A001.e.3
 that meet or exceed the technical
 parameters in 3A201.a and 3A201.b,
 respectively.
AT applies to entire entry................  AT Column 1.
 

Reporting Requirements: See Sec.  743.1 of the EAR for reporting 
requirements for exports under 3A001.b.2 or b.3 under License 
Exceptions, and Validated End-User authorizations.
License Requirements Note: See Sec.  744.17 of the EAR for 
additional license requirements for microprocessors having a 
processing speed of 5 GFLOPS or more and an arithmetic logic unit 
with an access width of 32 bit or more, including those 
incorporating ``information security'' functionality, and associated 
``software'' and ``technology'' for the ``production'' or 
``development'' of such microprocessors.

List Based License Exceptions (See Part 740 for a Description of All 
License Exceptions)

LVS: N/A for MT or NP; N/A for ``Monolithic Microwave Integrated 
Circuit'' (``MMIC'') amplifiers in 3A001.b.2 and discrete microwave 
transistors in 3A001.b.3, except those that are being exported or 
reexported for use in civil telecommunications applications.
Yes for:
$1500: 3A001.c
$3000: 3A001.b.1, b.2 (exported or reexported for use in civil 
telecommunications applications), b.3 (exported or reexported for 
use in civil telecommunications applications), b.9, .d, .e, .f, and 
.g.
$5000: 3A001.a (except a.1.a and a.5.a when controlled for MT), .b.4 
to b.7, and b.12.
GBS: Yes for 3A001.a.1.b, a.2 to a.14 (except .a.5.a when controlled 
for MT), b.2 (exported or reexported for use in civil 
telecommunications applications), b.8 (except for ``vacuum 
electronic devices'' exceeding 18 GHz), b.9., b.10, .g, and .h, and 
.i.

Special Conditions for STA

STA: License Exception STA may not be used to ship any item in 
3A001.b.2 or b.3, except those that are being exported or reexported 
for use in civil telecommunications applications, to any of the 
destinations listed in Country Group A:5 or A:6 (See Supplement No.1 
to part 740 of the EAR).

List of Items Controlled

Related Controls: (1) See Category XV of the USML for certain 
``space-qualified'' electronics and Category XI of the USML for 
certain ASICs, `transmit/receive modules,' or `transmit modules' 
``subject to the ITAR'' (see 22 CFR parts 120 through 130). (2) See 
also 3A101, 3A201, 3A611, 3A991, and 9A515.
Related Definitions: `Microcircuit' means a device in which a number 
of passive or active elements are considered as indivisibly 
associated on or within a continuous structure to perform the 
function of a circuit. For the purposes of integrated circuits in 
3A001.a.1, 5 x 10\3\ Gy(Si) = 5 x 10\5\ Rads (Si); 5 x 10\6\ Gy 
(Si)/s = 5 x 10\8\ Rads (Si)/s.
Items:

    a. General purpose integrated circuits, as follows:
    Note 1: Integrated circuits include the following types:

--``Monolithic integrated circuits'';
--``Hybrid integrated circuits'';
--``Multichip integrated circuits'';
--Film type integrated circuits, including silicon-on-sapphire 
integrated circuits'';
--``Optical integrated circuits'';
--``Three dimensional integrated circuits'';
--``Monolithic Microwave Integrated Circuits'' (``MMICs'').

    a.1. Integrated circuits designed or rated as radiation hardened 
to withstand any of the following:
    a.1.a. A total dose of 5 x 10\3\ Gy (Si), or higher;
    a.1.b. A dose rate upset of 5 x 10\6\ Gy (Si)/s, or higher; or
    a.1.c. A fluence (integrated flux) of neutrons (1 MeV 
equivalent) of 5 x 10\13\ n/cm\2\ or higher on silicon, or its 
equivalent for other materials;
    Note: 3A001.a.1.c does not apply to Metal Insulator 
Semiconductors (MIS).
    a.2. ``Microprocessor microcircuits,'' ``microcomputer 
microcircuits,'' microcontroller microcircuits, storage integrated 
circuits manufactured from a compound semiconductor, analog-to-
digital converters, integrated circuits that contain analog-to-
digital converters and store or

[[Page 12116]]

process the digitized data, digital-to-analog converters, electro-
optical or ``optical integrated circuits'' designed for ``signal 
processing'', field programmable logic devices, custom integrated 
circuits for which either the function is unknown or the control 
status of the equipment in which the integrated circuit will be used 
in unknown, Fast Fourier Transform (FFT) processors, Static Random-
Access Memories (SRAMs), or `non-volatile memories,' having any of 
the following:
    Technical Note: `Non-volatile memories' are memories with data 
retention over a period of time after a power shutdown.
    a.2.a. Rated for operation at an ambient temperature above 398 K 
(+125 [deg]C);
    a.2.b. Rated for operation at an ambient temperature below 218 K 
(-55 [deg]C); or
    a.2.c. Rated for operation over the entire ambient temperature 
range from 218 K (-55 [deg]C) to 398 K (+125 [deg]C);
    Note: 3A001.a.2 does not apply to integrated circuits designed 
for civil automobile or railway train applications.
    a.3. ``Microprocessor microcircuits'', ``microcomputer 
microcircuits'' and microcontroller microcircuits, manufactured from 
a compound semiconductor and operating at a clock frequency 
exceeding 40 MHz;
    Note: 3A001.a.3 includes digital signal processors, digital 
array processors and digital coprocessors.
    a.4. [Reserved]
    a.5. Analog-to-Digital Converter (ADC) and Digital-to-Analog 
Converter (DAC) integrated circuits, as follows:
    a.5.a. ADCs having any of the following:
    a.5.a.1. A resolution of 8 bit or more, but less than 10 bit, 
with a ``sample rate'' greater than 1.3 Giga Samples Per Second 
(GSPS);
    a.5.a.2. A resolution of 10 bit or more, but less than 12 bit, 
with a ``sample rate'' greater than 600 Mega Samples Per Second 
(MSPS);
    a.5.a.3. A resolution of 12 bit or more, but less than 14 bit, 
with a ``sample rate'' greater than 400 MSPS;
    a.5.a.4. A resolution of 14 bit or more, but less than 16 bit, 
with a ``sample rate'' greater than 250 MSPS; or
    a.5.a.5. A resolution of 16 bit or more with a ``sample rate'' 
greater than 65 MSPS;
    N.B.: For integrated circuits that contain analog-to-digital 
converters and store or process the digitized data see 3A001.a.14.
    Technical Notes:
    1. A resolution of n bit corresponds to a quantization of 2\n\ 
levels.
    2. The resolution of the ADC is the number of bits of the 
digital output that represents the measured analog input. Effective 
Number of Bits (ENOB) is not used to determine the resolution of the 
ADC.
    3. For ``multiple channel ADCs'', the ``sample rate'' is not 
aggregated and the ``sample rate'' is the maximum rate of any single 
channel.
    4. For ``interleaved ADCs'' or for ``multiple channel ADCs'' 
that are specified to have an interleaved mode of operation, the 
``sample rates'' are aggregated and the ``sample rate'' is the 
maximum combined total rate of all of the interleaved channels.
    a.5.b. Digital-to-Analog Converters (DAC) having any of the 
following:
    a.5.b.1. A resolution of 10-bit or more but less than 12-
bit,with an `adjusted update rate' of exceeding 3,500 MSPS; or
    a.5.b.2. A resolution of 12-bit or more and having any of the 
following:
    a.5.b.2.a. An `adjusted update rate' exceeding 1,250 MSPS but 
not exceeding 3,500 MSPS, and having any of the following:
    a.5.b.2.a.1. A settling time less than 9 ns to arrive at or 
within 0.024% of full scale from a full scale step; or
    a.5.b.2.a.2. A `Spurious Free Dynamic Range' (SFDR) greater than 
68 dBc (carrier) when synthesizing a full scale analog signal of 100 
MHz or the highest full scale analog signal frequency specified 
below 100 MHz; or
    a.5.b.2.b. An `adjusted update rate' exceeding 3,500 MSPS;
    Technical Notes:
    1. ``Spurious Free Dynamic Range'' (SFDR) is defined as the 
ratio of the RMS value of the carrier frequency (maximum signal 
component) at the input of the DAC to the RMS value of the next 
largest noise or harmonic distortion component at its output.
    2. SFDR is determined directly from the specification table or 
from the characterization plots of SFDR versus frequency.
    3. A signal is defined to be full scale when its amplitude is 
greater than -3 dBfs (full scale).
    4. ``Adjusted update rate'' for DACs is:
    a. For conventional (non-interpolating) DACs, the ``adjusted 
update rate'' is the rate at which the digital signal is converted 
to an analog signal and the output analog values are changed by the 
DAC. For DACs where the interpolation mode may be bypassed 
(interpolation factor of one), the DAC should be considered as a 
conventional (non-interpolating) DAC.
    b. For interpolating DACs (oversampling DACs), the `adjusted 
update rate' is defined as the DAC update rate divided by the 
smallest interpolating factor. For interpolating DACs, the `adjusted 
update rate' may be referred to by different terms including:

 input data rate
 input word rate
 input sample rate
 maximum total input bus rate
 maximum DAC clock rate for DAC clock input.

    a.6. Electro-optical and ``optical integrated circuits'', 
designed for ``signal processing'' and having all of the following:
    a.6.a. One or more than one internal ``laser'' diode;
    a.6.b. One or more than one internal light detecting element; 
and
    a.6.c. Optical waveguides;
    a.7. ``Field programmable logic devices'' having any of the 
following:
    a.7.a. A maximum number of single-ended digital input/outputs of 
greater than 700; or
    a.7.b. An ``aggregate one-way peak serial transceiver data 
rate'' of 500 Gb/s or greater;
    Note: 3A001.a.7 includes:

--Complex Programmable Logic Devices (CPLDs);
--Field Programmable Gate Arrays (FPGAs);
--Field Programmable Logic Arrays (FPLAs);
--Field Programmable Interconnects (FPICs).

    N.B.: For integrated circuits having field programmable logic 
devices that are combined with an analog-to-digital converter, see 
3A001.a.14.
    Technical Notes:
    1. Maximum number of digital input/outputs in 3A001.a.7.a is 
also referred to as maximum user input/outputs or maximum available 
input/outputs, whether the integrated circuit is packaged or bare 
die.
    2.  ``Aggregate one-way peak serial transceiver data rate'' is 
the product of the peak serial one-way transceiver data rate times 
the number of transceivers on the FPGA.
    a.8. [Reserved]
    a.9. Neural network integrated circuits;
    a.10. Custom integrated circuits for which the function is 
unknown, or the control status of the equipment in which the 
integrated circuits will be used is unknown to the manufacturer, 
having any of the following:
    a.10.a. More than 1,500 terminals;
    a.10.b. A typical ``basic gate propagation delay time'' of less 
than 0.02 ns; or
    a.10.c. An operating frequency exceeding 3 GHz;
    a.11. Digital integrated circuits, other than those described in 
3A001.a.3 to 3A001.a.10 and 3A001.a.12, based upon any compound 
semiconductor and having any of the following:
    a.11.a. An equivalent gate count of more than 3,000 (2 input 
gates); or
    a.11.b. A toggle frequency exceeding 1.2 GHz;
    a.12. Fast Fourier Transform (FFT) processors having a rated 
execution time for an N-point complex FFT of less than (N 
log2 N)/20,480 ms, where N is the number of points;
    Technical Note: When N is equal to 1,024 points, the formula in 
3A001.a.12 gives an execution time of 500 [micro]s.
    a.13. Direct Digital Synthesizer (DDS) integrated circuits 
having any of the following:
    a.13.a. A Digital-to-Analog Converter (DAC) clock frequency of 
3.5 GHz or more and a DAC resolution of 10 bit or more, but less 
than 12 bit; or
    a.13.b. A DAC clock frequency of 1.25 GHz or more and a DAC 
resolution of 12 bit or more;
    Technical Note: The DAC clock frequency may be specified as the 
master clock frequency or the input clock frequency.
    a.14. Integrated circuits that perform or are programmable to 
perform all of the following:
    a.14.a. Analog-to-digital conversions meeting any of the 
following:
    a.14.a.1. A resolution of 8 bit or more, but less than 10 bit, 
with a ``sample rate'' greater than 1.3 Giga Samples Per Second 
(GSPS);
    a.14.a.2. A resolution of 10 bit or more, but less than 12 bit, 
with a ``sample rate'' greater than 1.0 GSPS;
    a.14.a.3. A resolution of 12 bit or more, but less than 14 bit, 
with a ``sample rate'' greater than 1.0 GSPS;
    a.14.a.4. A resolution of 14 bit or more, but less than 16 bit, 
with a ``sample rate'' greater than 400 Mega Samples Per Second 
(MSPS); or

[[Page 12117]]

    a.14.a.5. A resolution of 16 bit or more with a ``sample rate'' 
greater than 180 MSPS; and
    a.14.b. Any of the following:
    a.14.b.1. Storage of digitized data; or
    a.14.b.2. Processing of digitized data;
    N.B. 1:  For analog-to-digital converter integrated circuits see 
3A001.a.5.a.
    N.B. 2:  For field programmable logic devices see 3A001.a.7.
    Technical Notes:
    1. A resolution of n bit corresponds to a quantization of 2\n\ 
levels.
    2. The resolution of the ADC is the number of bits of the 
digital output of the ADC that represents the measured analog input. 
Effective Number of Bits (ENOB) is not used to determine the 
resolution of the ADC.
    3. For integrated circuits with non-interleaving ``multiple 
channel ADCs'', the ``sample rate'' is not aggregated and the 
``sample rate'' is the maximum rate of any single channel.
    4. For integrated circuits with ``interleaved ADCs'' or with 
``multiple channel ADCs'' that are specified to have an interleaved 
mode of operation, the ``sample rates'' are aggregated and the 
``sample rate'' is the maximum combined total rate of all of the 
interleaved channels.
    b. Microwave or millimeter wave items, as follows:
    Technical Note: For purposes of 3A001.b, the parameter peak 
saturated power output may also be referred to on product data 
sheets as output power, saturated power output, maximum power 
output, peak power output, or peak envelope power output.
    b.1. ``Vacuum electronic devices'' and cathodes, as follows:
    Note 1: 3A001.b.1 does not control ``vacuum electronic devices'' 
designed or rated for operation in any frequency band and having all 
of the following:
    a. Does not exceed 31.8 GHz; and
    b. Is ``allocated by the ITU'' for radio-communications 
services, but not for radio-determination.
    Note 2: 3A001.b.1 does not control non-``space-qualified'' 
``vacuum electronic devices'' having all the following:
    a. An average output power equal to or less than 50 W; and
    b. Designed or rated for operation in any frequency band and 
having all of the following:
    1. Exceeds 31.8 GHz but does not exceed 43.5 GHz; and
    2.Is ``allocated by the ITU'' for radio-communications services, 
but not for radio-determination.
    b.1.a. Traveling-wave ``vacuum electronic devices,'' pulsed or 
continuous wave, as follows:
    b.1.a.1. Devices operating at frequencies exceeding 31.8 GHz;
    b.1.a.2. Devices having a cathode heater with a turn on time to 
rated RF power of less than 3 seconds;
    b.1.a.3. Coupled cavity devices, or derivatives thereof, with a 
``fractional bandwidth'' of more than 7% or a peak power exceeding 
2.5 kW;
    b.1.a.4. Devices based on helix, folded waveguide, or serpentine 
waveguide circuits, or derivatives thereof, having any of the 
following:
    b.1.a.4.a. An ``instantaneous bandwidth'' of more than one 
octave, and average power (expressed in kW) times frequency 
(expressed in GHz) of more than 0.5;
    b.1.a.4.b. An ``instantaneous bandwidth'' of one octave or less, 
and average power (expressed in kW) times frequency (expressed in 
GHz) of more than 1;
    b.1.a.4.c. Being ``space-qualified''; or
    b.1.a.4.d. Having a gridded electron gun;
    b.1.a.5. Devices with a ``fractional bandwidth'' greater than or 
equal to 10%, with any of the following:
    b.1.a.5.a. An annular electron beam;
    b.1.a.5.b. A non-axisymmetric electron beam; or
    b.1.a.5.c. Multiple electron beams;
    b.1.b. Crossed-field amplifier ``vacuum electronic devices'' 
with a gain of more than 17 dB;
    b.1.c. Thermionic cathodes, designed for ``vacuum electronic 
devices,'' producing an emission current density at rated operating 
conditions exceeding 5 A/cm\2\ or a pulsed (non-continuous) current 
density at rated operating conditions exceeding 10 A/cm\2\;
    b.1.d. ``Vacuum electronic devices'' with the capability to 
operate in a ``dual mode.''
    Technical Note: ``Dual mode'' means the ``vacuum electronic 
device'' beam current can be intentionally changed between 
continuous-wave and pulsed mode operation by use of a grid and 
produces a peak pulse output power greater than the continuous-wave 
output power.
    b.2. ``Monolithic Microwave Integrated Circuit'' (``MMIC'') 
amplifiers that are any of the following:
    N.B.: For ``MMIC'' amplifiers that have an integrated phase 
shifter see 3A001.b.12.
    b.2.a. Rated for operation at frequencies exceeding 2.7 GHz up 
to and including 6.8 GHz with a ``fractional bandwidth'' greater 
than 15%, and having any of the following:
    b.2.a.1. A peak saturated power output greater than 75 W (48.75 
dBm) at any frequency exceeding 2.7 GHz up to and including 2.9 GHz;
    b.2.a.2. A peak saturated power output greater than 55 W (47.4 
dBm) at any frequency exceeding 2.9 GHz up to and including 3.2 GHz;
    b.2.a.3. A peak saturated power output greater than 40 W (46 
dBm) at any frequency exceeding 3.2 GHz up to and including 3.7 GHz; 
or
    b.2.a.4. A peak saturated power output greater than 20 W (43 
dBm) at any frequency exceeding 3.7 GHz up to and including 6.8 GHz;
    b.2.b. Rated for operation at frequencies exceeding 6.8 GHz up 
to and including 16 GHz with a ``fractional bandwidth'' greater than 
10%, and having any of the following:
    b.2.b.1. A peak saturated power output greater than 10 W (40 
dBm) at any frequency exceeding 6.8 GHz up to and including 8.5 GHz; 
or
    b.2.b.2. A peak saturated power output greater than 5 W (37 dBm) 
at any frequency exceeding 8.5 GHz up to and including 16 GHz;
    b.2.c. Rated for operation with a peak saturated power output 
greater than 3 W (34.77 dBm) at any frequency exceeding 16 GHz up to 
and including 31.8 GHz, and with a ``fractional bandwidth'' of 
greater than 10%;
    b.2.d. Rated for operation with a peak saturated power output 
greater than 0.1 nW (-70 dBm) at any frequency exceeding 31.8 GHz up 
to and including 37 GHz;
    b.2.e. Rated for operation with a peak saturated power output 
greater than 1 W (30 dBm) at any frequency exceeding 37 GHz up to 
and including 43.5 GHz, and with a ``fractional bandwidth'' of 
greater than 10%;
    b.2.f. Rated for operation with a peak saturated power output 
greater than 31.62 mW (15 dBm) at any frequency exceeding 43.5 GHz 
up to and including 75 GHz, and with a ``fractional bandwidth'' of 
greater than 10%;
    b.2.g. Rated for operation with a peak saturated power output 
greater than 10 mW (10 dBm) at any frequency exceeding 75 GHz up to 
and including 90 GHz, and with a ``fractional bandwidth'' of greater 
than 5%; or
    b.2.h. Rated for operation with a peak saturated power output 
greater than 0.1 nW (-70 dBm) at any frequency exceeding 90 GHz;
    Note 1:  [Reserved]
    Note 2: The control status of the ``MMIC'' whose rated operating 
frequency includes frequencies listed in more than one frequency 
range, as defined by 3A001.b.2.a through 3A001.b.2.h, is determined 
by the lowest peak saturated power output control threshold.
    Note 3: Notes 1 and 2 following the Category 3 heading for 
product group A. Systems, Equipment, and Components mean that 
3A001.b.2 does not control ``MMICs'' if they are ``specially 
designed'' for other applications, e.g., telecommunications, radar, 
automobiles.
    b.3. Discrete microwave transistors that are any of the 
following:
    b.3.a. Rated for operation at frequencies exceeding 2.7 GHz up 
to and including 6.8 GHz and having any of the following:
    b.3.a.1. A peak saturated power output greater than 400 W (56 
dBm) at any frequency exceeding 2.7 GHz up to and including 2.9 GHz;
    b.3.a.2. A peak saturated power output greater than 205 W (53.12 
dBm) at any frequency exceeding 2.9 GHz up to and including 3.2 GHz;
    b.3.a.3. A peak saturated power output greater than 115 W (50.61 
dBm) at any frequency exceeding 3.2 GHz up to and including 3.7 GHz; 
or
    b.3.a.4. A peak saturated power output greater than 60 W (47.78 
dBm) at any frequency exceeding 3.7 GHz up to and including 6.8 GHz;
    b.3.b. Rated for operation at frequencies exceeding 6.8 GHz up 
to and including 31.8 GHz and having any of the following:
    b.3.b.1. A peak saturated power output greater than 50 W (47 
dBm) at any frequency exceeding 6.8 GHz up to and including 8.5 GHz;
    b.3.b.2. A peak saturated power output greater than 15 W (41.76 
dBm) at any frequency exceeding 8.5 GHz up to and including 12 GHz;
    b.3.b.3. A peak saturated power output greater than 40 W (46 
dBm) at any frequency exceeding 12 GHz up to and including 16 GHz; 
or

[[Page 12118]]

    b.3.b.4. A peak saturated power output greater than 7 W (38.45 
dBm) at any frequency exceeding 16 GHz up to and including 31.8 GHz;
    b.3.c. Rated for operation with a peak saturated power output 
greater than 0.5 W (27 dBm) at any frequency exceeding 31.8 GHz up 
to and including 37 GHz;
    b.3.d. Rated for operation with a peak saturated power output 
greater than 1 W (30 dBm) at any frequency exceeding 37 GHz up to 
and including 43.5 GHz;
    b.3.e. Rated for operation with a peak saturated power output 
greater than 0.1 nW (-70 dBm) at any frequency exceeding 43.5 GHz; 
or
    b.3.f. Other than those specified by 3A001.b.3.a to 3A001.b.3.e 
and rated for operation with a peak saturated power output greater 
than 5 W (37.0 dBm) at all frequencies exceeding 8.5 GHz up to and 
including 31.8 GHz;
    Note 1: The control status of a transistor in 3A001.b.3.a 
through 3A001.b.3.e, whose rated operating frequency includes 
frequencies listed in more than one frequency range, as defined by 
3A001.b.3.a through 3A001.b.3.e, is determined by the lowest peak 
saturated power output control threshold.
    Note 2: 3A001.b.3 includes bare dice, dice mounted on carriers, 
or dice mounted in packages. Some discrete transistors may also be 
referred to as power amplifiers, but the status of these discrete 
transistors is determined by 3A001.b.3.
    b.4. Microwave solid state amplifiers and microwave assemblies/
modules containing microwave solid state amplifiers, that are any of 
the following:
    b.4.a. Rated for operation at frequencies exceeding 2.7 GHz up 
to and including 6.8 GHz with a ``fractional bandwidth'' greater 
than 15%, and having any of the following:
    b.4.a.1. A peak saturated power output greater than 500 W (57 
dBm) at any frequency exceeding 2.7 GHz up to and including 2.9 GHz;
    b.4.a.2. A peak saturated power output greater than 270 W (54.3 
dBm) at any frequency exceeding 2.9 GHz up to and including 3.2 GHz;
    b.4.a.3. A peak saturated power output greater than 200 W (53 
dBm) at any frequency exceeding 3.2 GHz up to and including 3.7 GHz; 
or
    b.4.a.4. A peak saturated power output greater than 90 W (49.54 
dBm) at any frequency exceeding 3.7 GHz up to and including 6.8 GHz;
    b.4.b. Rated for operation at frequencies exceeding 6.8 GHz up 
to and including 31.8 GHz with a ``fractional bandwidth'' greater 
than 10%, and having any of the following:
    b.4.b.1. A peak saturated power output greater than 70 W (48.45 
dBm) at any frequency exceeding 6.8 GHz up to and including 8.5 GHz;
    b.4.b.2. A peak saturated power output greater than 50 W (47 
dBm) at any frequency exceeding 8.5 GHz up to and including 12 GHz;
    b.4.b.3. A peak saturated power output greater than 30 W (44.77 
dBm) at any frequency exceeding 12 GHz up to and including 16 GHz; 
or
    b.4.b.4. A peak saturated power output greater than 20 W (43 
dBm) at any frequency exceeding 16 GHz up to and including 31.8 GHz;
    b.4.c. Rated for operation with a peak saturated power output 
greater than 0.5 W (27 dBm) at any frequency exceeding 31.8 GHz up 
to and including 37 GHz;
    b.4.d. Rated for operation with a peak saturated power output 
greater than 2 W (33 dBm) at any frequency exceeding 37 GHz up to 
and including 43.5 GHz, and with a ``fractional bandwidth'' of 
greater than 10%;
    b.4.e. Rated for operation at frequencies exceeding 43.5 GHz and 
having any of the following:
    b.4.e.1. A peak saturated power output greater than 0.2 W (23 
dBm) at any frequency exceeding 43.5 GHz up to and including 75 GHz, 
and with a ``fractional bandwidth'' of greater than 10%;
    b.4.e.2. A peak saturated power output greater than 20 mW (13 
dBm) at any frequency exceeding 75 GHz up to and including 90 GHz, 
and with a ``fractional bandwidth'' of greater than 5%; or
    b.4.e.3. A peak saturated power output greater than 0.1 nW (-70 
dBm) at any frequency exceeding 90 GHz; or
    b.4.f. [Reserved]
    N.B.:
    1. For ``MMIC'' amplifiers see 3A001.b.2.
    2. For `transmit/receive modules' and `transmit modules' see 
3A001.b.12.
    3. For converters and harmonic mixers, designed to extend the 
operating or frequency range of signal analyzers, signal generators, 
network analyzers or microwave test receivers, see 3A001.b.7.
    Note 1: [Reserved]
    Note 2: The control status of an item whose rated operating 
frequency includes frequencies listed in more than one frequency 
range, as defined by 3A001.b.4.a through 3A001.b.4.e, is determined 
by the lowest peak saturated power output control threshold.
    b.5. Electronically or magnetically tunable band-pass or band-
stop filters, having more than 5 tunable resonators capable of 
tuning across a 1.5:1 frequency band (fmax/
fmin) in less than 10 [mu]s and having any of the 
following:
    b.5.a. A band-pass bandwidth of more than 0.5% of center 
frequency; or
    b.5.b. A band-stop bandwidth of less than 0.5% of center 
frequency;
    b.6. [Reserved]
    b.7. Converters and harmonic mixers, that are any of the 
following:
    b.7.a. Designed to extend the frequency range of ``signal 
analyzers'' beyond 90 GHz;
    b.7.b. Designed to extend the operating range of signal 
generators as follows:
    b.7.b.1. Beyond 90 GHz;
    b.7.b.2. To an output power greater than 100 mW (20 dBm) 
anywhere within the frequency range exceeding 43.5 GHz but not 
exceeding 90 GHz;
    b.7.c. Designed to extend the operating range of network 
analyzers as follows:
    b.7.c.1. Beyond 110 GHz;
    b.7.c.2. To an output power greater than 31.62 mW (15 dBm) 
anywhere within the frequency range exceeding 43.5 GHz but not 
exceeding 90 GHz;
    b.7.c.3. To an output power greater than 1 mW (0 dBm) anywhere 
within the frequency range exceeding 90 GHz but not exceeding 110 
GHz; or
    b.7.d. Designed to extend the frequency range of microwave test 
receivers beyond 110 GHz;
    b.8. Microwave power amplifiers containing ``vacuum electronic 
devices'' controlled by 3A001.b.1 and having all of the following:
    b.8.a. Operating frequencies above 3 GHz;
    b.8.b. An average output power to mass ratio exceeding 80 W/kg; 
and
    b.8.c. A volume of less than 400 cm\3\;
    Note: 3A001.b.8 does not control equipment designed or rated for 
operation in any frequency band which is ``allocated by the ITU'' 
for radio-communications services, but not for radio-determination.
    b.9. Microwave Power Modules (MPM) consisting of, at least, a 
traveling-wave ``vacuum electronic device,'' a ``Monolithic 
Microwave Integrated Circuit'' (``MMIC'') and an integrated 
electronic power conditioner and having all of the following:
    b.9.a. A `turn-on time' from off to fully operational in less 
than 10 seconds;
    b.9.b. A volume less than the maximum rated power in Watts 
multiplied by 10 cm\3\/W; and
    b.9.c. An ``instantaneous bandwidth'' greater than 1 octave 
(fmax > 2fmin) and having any of the 
following:
    b.9.c.1. For frequencies equal to or less than 18 GHz, an RF 
output power greater than 100 W; or
    b.9.c.2. A frequency greater than 18 GHz;
    Technical Notes:
    1. To calculate the volume in 3A001.b.9.b, the following example 
is provided: for a maximum rated power of 20 W, the volume would be: 
20 W x 10 cm3/W = 200 cm3.
    2. The `turn-on time' in 3A001.b.9.a refers to the time from 
fully-off to fully operational, i.e., it includes the warm-up time 
of the MPM.
    b.10. Oscillators or oscillator assemblies, specified to operate 
with a single sideband (SSB) phase noise, in dBc/Hz, less (better) 
than -(126 + 20log10F-20log10f) anywhere 
within the range of 10 Hz <= F <= 10 kHz;
    Technical Note: In 3A001.b.10, F is the offset from the 
operating frequency in Hz and f is the operating frequency in MHz.
    b.11. `Frequency synthesizer' ``electronic assemblies'' having a 
``frequency switching time'' as specified by any of the following:
    b.11.a. Less than 143 ps;
    b.11.b. Less than 100 [mu]s for any frequency change exceeding 
2.2 GHz within the synthesized frequency range exceeding 4.8 GHz but 
not exceeding 31.8 GHz;
    b.11.c. [Reserved]
    b.11.d. Less than 500 [micro]s for any frequency change 
exceeding 550 MHz within the synthesized frequency range exceeding 
31.8 GHz but not exceeding 37 GHz;
    b.11.e. Less than 100 [micro]s for any frequency change 
exceeding 2.2 GHz within the synthesized frequency range exceeding 
37 GHz but not exceeding 75 GHz;
    b.11.f. Less than 100 [micro]s for any frequency change 
exceeding 5.0 GHz within the synthesized frequency range exceeding 
75 GHz but not exceeding 90 GHz; or

[[Page 12119]]

    b.11.g. Less than 1 ms within the synthesized frequency range 
exceeding 90 GHz;
    Technical Note: A `frequency synthesizer' is any kind of 
frequency source, regardless of the actual technique used, providing 
a multiplicity of simultaneous or alternative output frequencies, 
from one or more outputs, controlled by, derived from or disciplined 
by a lesser number of standard (or master) frequencies.
    N.B.: For general purpose ``signal analyzers'', signal 
generators, network analyzers and microwave test receivers, see 
3A002.c, 3A002.d, 3A002.e and 3A002.f, respectively.
    b.12. `Transmit/receive modules,' `transmit/receive MMICs,' 
`transmit modules,' and `transmit MMICs,' rated for operation at 
frequencies above 2.7 GHz and having all of the following:
    b.12.a. A peak saturated power output (in watts), 
Psat, greater than 505.62 divided by the maximum 
operating frequency (in GHz) squared [Psat>505.62 
W*GHz\2\/fGHz\2\] for any channel;
    b.12.b. A ``fractional bandwidth'' of 5% or greater for any 
channel;
    b.12.c. Any planar side with length d (in cm) equal to or less 
than 15 divided by the lowest operating frequency in GHz 
[d<=15cm*GHz*N/fGHz] where N is the number of transmit or 
transmit/receive channels; and
    b.12.d. An electronically variable phase shifter per channel.
    Technical Notes:
    1. A `transmit/receive module' is a multifunction ``electronic 
assembly'' that provides bi-directional amplitude and phase control 
for transmission and reception of signals.
    2. A `transmit module' is an ``electronic assembly'' that 
provides amplitude and phase control for transmission of signals.
    3. A `transmit/receive MMIC' is a multifunction ``MMIC'' that 
provides bi-directional amplitude and phase control for transmission 
and reception of signals.
    4. A `transmit MMIC' is a ``MMIC'' that provides amplitude and 
phase control for transmission of signals.
    5. 2.7 GHz should be used as the lowest operating frequency 
(fGHz) in the formula in 3A001.b.12.c for transmit/receive or 
transmit modules that have a rated operation range extending 
downward to 2.7 GHz and below [d<=15cm*GHz*N/2.7 GHz].
    6. 3A001.b.12 applies to `transmit/receive modules' or `transmit 
modules' with or without a heat sink. The value of d in 3A001.b.12.c 
does not include any portion of the `transmit/receive module' or 
`transmit module' that functions as a heat sink.
    7. `Transmit/receive modules' or `transmit modules,' `transmit/
receive MMICs' or `transmit MMICs' may or may not have N integrated 
radiating antenna elements where N is the number of transmit or 
transmit/receive channels.
    c. Acoustic wave devices as follows and ``specially designed'' 
``components'' therefor:
    c.1. Surface acoustic wave and surface skimming (shallow bulk) 
acoustic wave devices, having any of the following:
    c.1.a. A carrier frequency exceeding 6 GHz;
    c.1.b. A carrier frequency exceeding 1 GHz, but not exceeding 6 
GHz and having any of the following:
    c.1.b.1. A `frequency side-lobe rejection' exceeding 65 dB;
    c.1.b.2. A product of the maximum delay time and the bandwidth 
(time in [mu]s and bandwidth in MHz) of more than 100;
    c.1.b.3. A bandwidth greater than 250 MHz; or
    c.1.b.4. A dispersive delay of more than 10 [mu]s; or
    c.1.c. A carrier frequency of 1 GHz or less and having any of 
the following:
    c.1.c.1. A product of the maximum delay time and the bandwidth 
(time in [mu]s and bandwidth in MHz) of more than 100;
    c.1.c.2. A dispersive delay of more than 10 [mu]s; or
    c.1.c.3. A `frequency side-lobe rejection' exceeding 65 dB and a 
bandwidth greater than 100 MHz;
    Technical Note: `Frequency side-lobe rejection' is the maximum 
rejection value specified in data sheet.
    c.2. Bulk (volume) acoustic wave devices that permit the direct 
processing of signals at frequencies exceeding 6 GHz;
    c.3. Acoustic-optic ``signal processing'' devices employing 
interaction between acoustic waves (bulk wave or surface wave) and 
light waves that permit the direct processing of signals or images, 
including spectral analysis, correlation or convolution;
    Note: 3A001.c does not control acoustic wave devices that are 
limited to a single band pass, low pass, high pass or notch 
filtering, or resonating function.
    d. Electronic devices and circuits containing ``components,'' 
manufactured from ``superconductive'' materials, ``specially 
designed'' for operation at temperatures below the ``critical 
temperature'' of at least one of the ``superconductive'' 
constituents and having any of the following:
    d.1. Current switching for digital circuits using 
``superconductive'' gates with a product of delay time per gate (in 
seconds) and power dissipation per gate (in watts) of less than 
10-\14\ J; or
    d.2. Frequency selection at all frequencies using resonant 
circuits with Q-values exceeding 10,000;
    e. High energy devices as follows:
    e.1. `Cells' as follows:
    e.1.a. `Primary cells' having any of the following at 20 [deg]C:
    e.1.a.1. `Energy density' exceeding 550 Wh/kg and a `continuous 
power density' exceeding 50 W/kg; or
    e.1.a.2. `Energy density' exceeding 50 Wh/kg and a `continuous 
power density' exceeding 350 W/kg;
    e.1.b. `Secondary cells' having an `energy density' exceeding 
350 Wh/kg at 20 [deg]C;
    Technical Notes:
    1. For the purpose of 3A001.e.1, `energy density' (Wh/kg) is 
calculated from the nominal voltage multiplied by the nominal 
capacity in ampere-hours (Ah) divided by the mass in kilograms. If 
the nominal capacity is not stated, energy density is calculated 
from the nominal voltage squared then multiplied by the discharge 
duration in hours divided by the discharge load in Ohms and the mass 
in kilograms.
    2. For the purpose of 3A001.e.1, a `cell' is defined as an 
electrochemical device, which has positive and negative electrodes, 
an electrolyte, and is a source of electrical energy. It is the 
basic building block of a battery.
    3. For the purpose of 3A001.e.1.a, a `primary cell' is a `cell' 
that is not designed to be charged by any other source.
    4. For the purpose of 3A001.e.1.b, a `secondary cell' is a 
`cell' that is designed to be charged by an external electrical 
source.
    5. For the purpose of 3A001.e.1.a, `continuous power density' 
(W/kg) is calculated from the nominal voltage multiplied by the 
specified maximum continuous discharge current in amperes (A) 
divided by the mass in kilograms. `Continuous power density' is also 
referred to as specific power.
    Note: 3A001.e does not control batteries, including single-cell 
batteries.
    e.2. High energy storage capacitors as follows:
    e.2.a. Capacitors with a repetition rate of less than 10 Hz 
(single shot capacitors) and having all of the following:
    e.2.a.1. A voltage rating equal to or more than 5 kV;
    e.2.a.2. An energy density equal to or more than 250 J/kg; and
    e.2.a.3. A total energy equal to or more than 25 kJ;
    e.2.b. Capacitors with a repetition rate of 10 Hz or more 
(repetition rated capacitors) and having all of the following:
    e.2.b.1. A voltage rating equal to or more than 5 kV;
    e.2.b.2. An energy density equal to or more than 50 J/kg;
    e.2.b.3. A total energy equal to or more than 100 J; and
    e.2.b.4. A charge/discharge cycle life equal to or more than 
10,000;
    e.3. ``Superconductive'' electromagnets and solenoids, 
``specially designed'' to be fully charged or discharged in less 
than one second and having all of the following:
    Note: 3A001.e.3 does not control ``superconductive'' 
electromagnets or solenoids ``specially designed'' for Magnetic 
Resonance Imaging (MRI) medical equipment.
    e.3.a. Energy delivered during the discharge exceeding 10 kJ in 
the first second;
    e.3.b. Inner diameter of the current carrying windings of more 
than 250 mm; and
    e.3.c. Rated for a magnetic induction of more than 8 T or 
``overall current density'' in the winding of more than 300 A/mm\2\;
    e.4. Solar cells, cell-interconnect-coverglass (CIC) assemblies, 
solar panels, and solar arrays, which are ``space-qualified,'' 
having a minimum average efficiency exceeding 20% at an operating 
temperature of 301 K (28 [deg]C) under simulated `AM0' illumination 
with an irradiance of 1,367 Watts per square meter (W/m\2\);
    Technical Note: `AM0', or `Air Mass Zero', refers to the 
spectral irradiance of sun light in the earth's outer atmosphere 
when the distance between the earth and sun is one astronomical unit 
(AU).
    f. Rotary input type absolute position encoders having an 
``accuracy'' equal to or less (better) than 1.0 second of arc and

[[Page 12120]]

``specially designed'' encoder rings, discs or scales therefor;
    g. Solid-state pulsed power switching thyristor devices and 
`thyristor modules', using either electrically, optically, or 
electron radiation controlled switch methods and having any of the 
following:
    g.1. A maximum turn-on current rate of rise (di/dt) greater than 
30,000 A/[mu]s and off-state voltage greater than 1,100 V; or
    g.2. A maximum turn-on current rate of rise (di/dt) greater than 
2,000 A/[mu]s and having all of the following:
    g.2.a. An off-state peak voltage equal to or greater than 3,000 
V; and
    g.2.b. A peak (surge) current equal to or greater than 3,000 A;
    Note 1: 3A001.g. includes:

--Silicon Controlled Rectifiers (SCRs)
--Electrical Triggering Thyristors (ETTs)
--Light Triggering Thyristors (LTTs)
--Integrated Gate Commutated Thyristors (IGCTs)
--Gate Turn-off Thyristors (GTOs)
--MOS Controlled Thyristors (MCTs)
--Solidtrons

    Note 2: 3A001.g does not control thyristor devices and 
`thyristor modules' incorporated into equipment designed for civil 
railway or ``civil aircraft'' applications.
    Technical Note: For the purposes of 3A001.g, a `thyristor 
module' contains one or more thyristor devices.
    h. Solid-state power semiconductor switches, diodes, or 
`modules', having all of the following:
    h.1. Rated for a maximum operating junction temperature greater 
than 488 K (215 [deg]C);
    h.2. Repetitive peak off-state voltage (blocking voltage) 
exceeding 300 V; and
    h.3. Continuous current greater than 1 A.
    Technical Note: For the purposes of 3A001.h, `modules' contain 
one or more solid-state power semiconductor switches or diodes.
    Note 1: Repetitive peak off-state voltage in 3A001.h includes 
drain to source voltage, collector to emitter voltage, repetitive 
peak reverse voltage and peak repetitive off-state blocking voltage.
    Note 2: 3A001.h includes:

--Junction Field Effect Transistors (JFETs)
--Vertical Junction Field Effect Transistors (VJFETs)
--Metal Oxide Semiconductor Field Effect Transistors (MOSFETs)
--Double Diffused Metal Oxide Semiconductor Field Effect Transistor 
(DMOSFET)
--Insulated Gate Bipolar Transistor (IGBT)
--High Electron Mobility Transistors (HEMTs)
--Bipolar Junction Transistors (BJTs)
--Thyristors and Silicon Controlled Rectifiers (SCRs)
--Gate Turn-Off Thyristors (GTOs)
--Emitter Turn-Off Thyristors (ETOs)
--PiN Diodes
--Schottky Diodes

    Note 3: 3A001.h does not apply to switches, diodes, or 
`modules', incorporated into equipment designed for civil 
automobile, civil railway, or ``civil aircraft'' applications.
    i. Intensity, amplitude, or phase electro-optic modulators, 
designed for analog signals and having any of the following:
    i.1. A maximum operating frequency of more than 10 GHz but less 
than 20 GHz, an optical insertion loss equal to or less than 3 dB 
and having any of the following:
    i.1.a. A `half-wave voltage' (`V[pi]') less than 2.7 V when 
measured at a frequency of 1 GHz or below; or
    i.1.b. A `V[pi]' of less than 4 V when measured at a frequency 
of more than 1 GHz; or
    i.2. A maximum operating frequency equal to or greater than 20 
GHz, an optical insertion loss equal to or less than 3 dB and having 
any of the following:
    i.2.a. A `V[pi]' less than 3.3 V when measured at a frequency of 
1 GHz or below; or
    i.2.b. A `V[pi]' less than 5 V when measured at a frequency of 
more than 1 GHz.
    Note: 3A001.i includes electro-optic modulators having optical 
input and output connectors (e.g., fiber-optic pigtails).
    Technical Note: For the purposes of 3A001.i, a `half-wave 
voltage' (`V[pi]') is the applied voltage necessary to make a phase 
change of 180 degrees in the wavelength of light propagating through 
the optical modulator.

3A002 General purpose ``electronic assemblies,'' modules and 
equipment, as follows (see List of Items Controlled).

License Requirements

Reason for Control: NS, MT, AT

 
                                            Country chart (see Supp. No.
                Control(s)                         1 to part 738)
 
NS applies to entire entry................  NS Column 2.
MT applies to 3A002.h when the parameters   MT Column 1.
 in 3A101.a.2.b are met or exceeded.
AT applies to entire entry................  AT Column 1.
 

Reporting Requirements

See Sec.  743.1 of the EAR for reporting requirements for exports 
under License Exceptions, and Validated End-User authorizations.

List Based License Exceptions (See Part 740 for a Description of All 
License Exceptions)

LVS: $3000: 3A002.a, .e, .f, and .g
$5000: 3A002.c to .d, and .h (unless controlled for MT);
GBS: Yes, for 3A002.h (unless controlled for MT)

Special Conditions for STA

STA: License Exception STA may not be used to ship any item in 
3A002.g.1 to any of the destinations listed in Country Group A:6 
(See Supplement No.1 to part 740 of the EAR).

List of Items Controlled

Related Controls: See Category XV(e)(9) of the USML for certain 
``space-qualified'' atomic frequency standards ``subject to the 
ITAR'' (see 22 CFR parts 120 through 130). See also 3A101, 3A992 and 
9A515.x.
Related Definitions: Constant percentage bandwidth filters are also 
known as octave or fractional octave filters.
Items:

    a. Recording equipment and oscilloscopes, as follows:
    a.1. to a.5. [Reserved]
    N.B.: For waveform digitizers and transient recorders, see 
3A002.h.
    a.6. Digital data recorders having all of the following:
    a.6.a. A sustained `continuous throughput' of more than 6.4 
Gbit/s to disk or solid-state drive memory; and
    a.6.b. ``Signal processing'' of the radio frequency signal data 
while it is being recorded;
    Technical Notes:
    1. For recorders with a parallel bus architecture, the 
`continuous throughput' rate is the highest word rate multiplied by 
the number of bits in a word.
    2. `Continuous throughput' is the fastest data rate the 
instrument can record to disk or solid-state drive memory without 
the loss of any information while sustaining the input digital data 
rate or digitizer conversion rate.
    a.7. Real-time oscilloscopes having a vertical root-mean-square 
(rms) noise voltage of less than 2% of full-scale at the vertical 
scale setting that provides the lowest noise value for any input 3dB 
bandwidth of 60 GHz or greater per channel;
    Note: 3A002.a.7 does not apply to equivalent-time sampling 
oscilloscopes.
    b. [Reserved]
    c. ``Signal analyzers'' as follows:
    c.1. ``Signal analyzers'' having a 3 dB resolution bandwidth 
(RBW) exceeding 40 MHz anywhere within the frequency range exceeding 
31.8 GHz but not exceeding 37 GHz;
    c.2. ``Signal analyzers'' having a Displayed Average Noise Level 
(DANL) less (better) than -150 dBm/Hz anywhere within the frequency 
range exceeding 43.5 GHz but not exceeding 90 GHz;
    c.3. ``Signal analyzers'' having a frequency exceeding 90 GHz;
    c.4. ``Signal analyzers'' having all of the following:
    c.4.a. `Real-time bandwidth' exceeding 170 MHz; and
    c.4.b. Having any of the following:
    c.4.b.1. 100% probability of discovery, with less than a 3 dB 
reduction from full amplitude due to gaps or windowing effects, of 
signals having a duration of 15 [mu]s or less; or
    c.4.b.2. A `frequency mask trigger' function, with 100% 
probability of trigger (capture) for signals having a duration of 15 
[mu]s or less;
    Technical Notes:
    1. `Real-time bandwidth' is the widest frequency range for which 
the analyzer can continuously transform time-domain data entirely 
into frequency-domain results, using a Fourier or other discrete 
time transform that processes every incoming time point, without a 
reduction of measured amplitude of more than 3 dB below the actual 
signal amplitude caused by gaps or windowing effects, while 
outputting or displaying the transformed data.

[[Page 12121]]

    2. Probability of discovery in 3A002.c.4.b.1 is also referred to 
as probability of intercept or probability of capture.
    3. For the purposes of 3A002.c.4.b.1, the duration for 100% 
probability of discovery is equivalent to the minimum signal 
duration necessary for the specified level measurement uncertainty.
    4. A `frequency mask trigger' is a mechanism where the trigger 
function is able to select a frequency range to be triggered on as a 
subset of the acquisition bandwidth while ignoring other signals 
that may also be present within the same acquisition bandwidth. A 
`frequency mask trigger' may contain more than one independent set 
of limits.
    Note: 3A002.c.4 does not apply to those ``signal analyzers'' 
using only constant percentage bandwidth filters (also known as 
octave or fractional octave filters).
    c.5. [Reserved]
    d. Signal generators having any of the following:
    d.1. Specified to generate pulse-modulated signals having all of 
the following, anywhere within the frequency range exceeding 31.8 
GHz but not exceeding 37 GHz:
    d.1.a. `Pulse duration' of less than 25 ns; and
    d.1.b. On/off ratio equal to or exceeding 65 dB;
    d.2. An output power exceeding 100 mW (20 dBm) anywhere within 
the frequency range exceeding 43.5 GHz but not exceeding 90 GHz;
    d.3. A ``frequency switching time'' as specified by any of the 
following:
    d.3.a. [Reserved]
    d.3.b. Less than 100 [mu]s for any frequency change exceeding 
2.2 GHz within the frequency range exceeding 4.8 GHz but not 
exceeding 31.8 GHz;
    d.3.c. [Reserved]
    d.3.d. Less than 500 [mu]s for any frequency change exceeding 
550 MHz within the frequency range exceeding 31.8 GHz but not 
exceeding 37 GHz;
    d.3.e. Less than 100 [mu]s for any frequency change exceeding 
2.2 GHz within the frequency range exceeding 37 GHz but not 
exceeding 75 GHz; or
    d.3.f. [Reserved]
    d.3.g. Less than 100 [mu]s for any frequency change exceeding 
5.0 GHz within the frequency range exceeding 75 GHz but not 
exceeding 90 GHz.
    d.4. A single sideband (SSB) phase noise, in dBc/Hz, specified 
as being any of the following:
    d.4.a. Less (better) than -(126 + 20 log10 F-
20log10f) for anywhere within the range of 10 Hz <= F <= 
10 kHz anywhere within the frequency range exceeding 3.2 GHz but not 
exceeding 90 GHz; or
    d.4.b. Less (better) than -(206-20log10f) for 
anywhere within the range of 10 kHz < F <= 100 kHz anywhere within 
the frequency range exceeding 3.2 GHz but not exceeding 90 GHz;
    Technical Note: In 3A002.d.4, F is the offset from the operating 
frequency in Hz and f is the operating frequency in MHz.
    d.5. An `RF modulation bandwidth' of digital baseband signals as 
specified by any of the following:
    d.5.a. Exceeding 2.2 GHz within the frequency range exceeding 
4.8 GHz but not exceeding 31.8 GHz;
    d.5.b. Exceeding 550 MHz within the frequency range exceeding 
31.8 GHz but not exceeding 37 GHz;
    d.5.c. Exceeding 2.2 GHz within the frequency range exceeding 37 
GHz but not exceeding 75 GHz;
    d.5.d. Exceeding 5.0 GHz within the frequency range exceeding 75 
GHz but not exceeding 90 GHz; or
    Technical Note: `RF modulation bandwidth' is the Radio Frequency 
(RF) bandwidth occupied by a digitally encoded baseband signal 
modulated onto an RF signal. It is also referred to as information 
bandwidth or vector modulation bandwidth. I/Q digital modulation is 
the technical method for producing a vector-modulated RF output 
signal, and that output signal is typically specified as having an 
`RF modulation bandwidth'.
    d.6. A maximum frequency exceeding 90 GHz;
    Note 1: For the purpose of 3A002.d, signal generators include 
arbitrary waveform and function generators.
    Note 2: 3A002.d does not control equipment in which the output 
frequency is either produced by the addition or subtraction of two 
or more crystal oscillator frequencies, or by an addition or 
subtraction followed by a multiplication of the result.
    Technical Notes:
    1. The maximum frequency of an arbitrary waveform or function 
generator is calculated by dividing the sample rate, in samples/
second, by a factor of 2.5.
    2. For the purposes of 3A002.d.1.a, `pulse duration' is defined 
as the time interval from the point on the leading edge that is 50% 
of the pulse amplitude to the point on the trailing edge that is 50% 
of the pulse amplitude.
    e. Network analyzers having any of the following:
    e.1. An output power exceeding 31.62 mW (15 dBm) anywhere within 
the operating frequency range exceeding 43.5 GHz but not exceeding 
90 GHz;
    e.2. An output power exceeding 1 mW (0 dBm) anywhere within the 
operating frequency range exceeding 90 GHz but not exceeding 110 
GHz;
    e.3. `Nonlinear vector measurement functionality' at frequencies 
exceeding 50 GHz but not exceeding 110 GHz; or
    Technical Note: `Nonlinear vector measurement functionality' is 
an instrument's ability to analyze the test results of devices 
driven into the large-signal domain or the non-linear distortion 
range.
    e.4. A maximum operating frequency exceeding 110 GHz;
    f. Microwave test receivers having all of the following:
    f.1. Maximum operating frequency exceeding 110 GHz; and
    f.2. Being capable of measuring amplitude and phase 
simultaneously;
    g. Atomic frequency standards being any of the following:
    g.1. ``Space-qualified'';
    g.2. Non-rubidium and having a long-term stability less (better) 
than 1 x 10-\11\/month; or
    g.3. Non-``space-qualified'' and having all of the following:
    g.3.a. Being a rubidium standard;
    g.3.b. Long-term stability less (better) than 1 x 
10-\11\/month; and
    g.3.c. Total power consumption of less than 1 Watt.
    h. ``Electronic assemblies,'' modules or equipment, specified to 
perform all of the following:
    h.1. Analog-to-digital conversions meeting any of the following:
    h.1.a. A resolution of 8 bit or more, but less than 10 bit, with 
a ``sample rate'' greater than 1.3 Giga Samples Per Second (GSPS);
    h.1.b. A resolution of 10 bit or more, but less than 12 bit, 
with a ``sample rate'' greater than 1.0 GSPS;
    h.1.c. A resolution of 12 bit or more, but less than 14 bit, 
with a ``sample rate'' greater than 1.0 GSPS;
    h.1.d. A resolution of 14 bit or more but less than 16 bit, with 
a ``sample rate'' greater than 400 Mega Samples Per Second (MSPS); 
or
    h.1.e. A resolution of 16 bit or more with a ``sample rate'' 
greater than 180 MSPS; and
    h.2. Any of the following:
    h.2.a. Output of digitized data;
    h.2.b. Storage of digitized data; or
    h.2.c. Processing of digitized data;
    N.B.: Digital data recorders, oscilloscopes, ``signal 
analyzers,'' signal generators, network analyzers and microwave test 
receivers, are specified by 3A002.a.6, 3A002.a.7, 3A002.c, 3A002.d, 
3A002.e and 3A002.f, respectively.
    Technical Notes:
    1. A resolution of n bit corresponds to a quantization of 2n 
levels.
    2. The resolution of the ADC is the number of bits of the 
digital output of the ADC that represents the measured analog input 
word. Effective Number of Bits (ENOB) is not used to determine the 
resolution of the ADC.
    3. For non-interleaved multiple-channel ``electronic 
assemblies'', modules, or equipment, the ``sample rate'' is not 
aggregated and the ``sample rate'' is the maximum rate of any single 
channel.
    4. For interleaved channels on multiple-channel ``electronic 
assemblies'', modules, or equipment, the ``sample rates'' are 
aggregated and the ``sample rate'' is the maximum combined total 
rate of all the interleaved channels.
    Note: 3A002.h includes ADC cards, waveform digitizers, data 
acquisition cards, signal acquisition boards and transient 
recorders.
* * * * *

Category 5--Telecommunications and ``Information Security''

* * * * *

II. Non-Cryptographic ``Information Security''

5A003 ``Systems,'' ``equipment'' and ``components,'' for non-
cryptographic ``information security,'' as follows (see List of 
Items Controlled).

License Requirements

Reason for Control: NS, AT

[[Page 12122]]



 
                                            Country chart (see Supp. No.
                Control(s)                         1 to part 738)
 
NS applies to entire entry................  NS Column 2.
AT applies to entire entry................  AT Column 1.
 

List Based License Exceptions (See Part 740 for a Description of All 
License Exceptions)

LVS: Yes: $500 for ``components.''
N/A for systems and equipment.
GBS: N/A

List of Items Controlled

Related Controls: N/A
Related Definitions: N/A
Items:

    a. Communications cable systems designed or modified to use 
mechanical, electrical or electronic means to detect surreptitious 
intrusion;
    Note: 5A003.a applies only to physical layer security. For the 
purpose of 5A003.a, the physical layer includes Layer 1 of the 
Reference Model of Open Systems Interconnection (OSI) (ISO/IEC 7498-
1).
    b. ``Specially designed'' or modified to reduce the compromising 
emanations of information-bearing signals beyond what is necessary 
for health, safety or electromagnetic interference standards.
* * * * *

Category 6--Sensors and Lasers

* * * * *
6A005 ``Lasers'', ``components'' and optical equipment, as follows 
(see List of Items Controlled), excluding items that are subject to 
the export licensing authority of the Nuclear Regulatory Commission 
(see 10 CFR part 110).

License Requirements

Reason for Control: NS, NP, AT

 
                                            Country chart (see Supp. No.
                Control(s)                         1 to part 738)
 
NS applies to entire entry................  NS Column 2.
NP applies to lasers controlled by          NP Column 1.
 6A005.a.2, a.3, a.4, b.2.b, b.3, b.4,
 b.6.c, c.1.b, c.2.b, d.2, d.3.c, or d.4.c
 that meet or exceed the technical
 parameters described in 6A205.
AT applies to entire entry................  AT Column 1.
 

List Based License Exceptions (See Part 740 for a Description of All 
License Exceptions)

LVS: N/A for NP items
$3000 for all other items
GBS: Neodymium-doped (other than glass) ``lasers'' controlled by 
6A005.b.6.d.2 (except 6A005.b.6.d.2.b) that have an output 
wavelength exceeding 1,000 nm, but not exceeding 1,100 nm, and an 
average or CW output power not exceeding 2 kW, and operate in a 
pulse-excited, non- ``Q-switched'' multiple-transverse mode, or in a 
continuously excited, multiple-transverse mode; Dye and Liquid 
Lasers controlled by 6A005.c.1, c.2 and c.3, except for a pulsed 
single longitudinal mode oscillator having an average output power 
exceeding 1 W and a repetition rate exceeding 1 kHz if the ``pulse 
duration'' is less than 100 ns; CO ``lasers'' controlled by 
6A005.d.2 having a CW maximum rated single or multimode output power 
not exceeding 10 kW; CO2 or CO/CO2 ``lasers'' 
controlled by 6A005.d.3 having an output wavelength in the range 
from 9,000 to 11,000 nm and having a pulsed output not exceeding 2 J 
per pulse and a maximum rated average single or multimode output 
power not exceeding 5 kW; and CO2 ``lasers'' controlled 
by 6A005.d.3 that operate in CW multiple-transverse mode, and having 
a CW output power not exceeding 15 kW.

List of Items Controlled

Related Controls (1) See ECCN 6D001 for ``software'' for items 
controlled under this entry. (2) See ECCNs 6E001 (``development''), 
6E002 (``production''), and 6E201 (``use'') for technology for items 
controlled under this entry. (3) Also see ECCNs 6A205 and 6A995. (4) 
See ECCN 3B001 for excimer ``lasers'' ``specially designed'' for 
lithography equipment. (5) ``Lasers'' ``specially designed'' or 
prepared for use in isotope separation are subject to the export 
licensing authority of the Nuclear Regulatory Commission (see 10 CFR 
part 110). (6) See USML Category XII(b) and (e) for laser systems or 
lasers subject to the ITAR. (7) See USML Category XVIII for certain 
laser-based directed energy weapon systems, equipment, and 
components subject to the ITAR.
Related Definitions: (1) `Wall-plug efficiency' is defined as the 
ratio of ``laser'' output power (or ``average output power'') to 
total electrical input power required to operate the ``laser'', 
including the power supply/conditioning and thermal conditioning/
heat exchanger, see 6A005.a.6.b.1 and 6A005.b.6; (2) `Non-repetitive 
pulsed' refers to ``lasers'' that produce either a single output 
pulse or that have a time interval between pulses exceeding one 
minute, see Note 2 of 6A005 and 6A005.d.6.
Items:

    Notes:
    1. Pulsed ``lasers'' include those that run in a continuous wave 
(CW) mode with pulses superimposed.
    2. Excimer, semiconductor, chemical, CO, CO2, and `non-
repetitive pulsed' Nd:glass ``lasers'' are only specified by 
6A005.d.
    Technical Note: `Non-repetitive pulsed' refers to ``lasers'' 
that produce either a single output pulse or that have a time 
interval between pulses exceeding one minute.
    3. 6A005 includes fiber ``lasers''.
    4. The control status of ``lasers'' incorporating frequency 
conversion (i.e., wavelength change) by means other than one 
``laser'' pumping another ``laser'' is determined by applying the 
control parameters for both the output of the source ``laser'' and 
the frequency-converted optical output.
    5. 6A005 does not control ``lasers'' as follows:
    a. Ruby with output energy below 20 J;
    b. Nitrogen;
    c. Krypton.
    6. For the purposes of 6A005.a and 6A005.b, `single transverse 
mode' refers to ``lasers'' with a beam profile having an M2-factor 
of less than 1.3, while `multiple transverse mode' refers to 
``lasers'' with a beam profile having an M2-factor of 1.3 or higher.
    a. Non-``tunable'' continuous wave ``(CW) lasers'' having any of 
the following:
    a.1. Output wavelength less than 150 nm and output power 
exceeding 1W;
    a.2. Output wavelength of 150 nm or more but not exceeding 510 
nm and output power exceeding 30 W;
    Note: 6A005.a.2 does not control Argon ``lasers'' having an 
output power equal to or less than 50 W.
    a.3. Output wavelength exceeding 510 nm but not exceeding 540 nm 
and any of the following:
    a.3.a. `Single transverse mode' output and output power 
exceeding 50 W; or
    a.3.b. `Multiple transverse mode' output and output power 
exceeding 150 W;
    a.4. Output wavelength exceeding 540 nm but not exceeding 800 nm 
and output power exceeding 30 W;
    a.5. Output wavelength exceeding 800 nm but not exceeding 975 nm 
and any of the following:
    a.5.a. `Single transverse mode' output and output power 
exceeding 50 W; or
    a.5.b. `Multiple transverse mode' output and output power 
exceeding 80 W;
    a.6. Output wavelength exceeding 975 nm but not exceeding 1,150 
nm and any of the following;
    a.6.a. `Single transverse mode' output and any of the following:
    a.6.a.1. Output power exceeding 1,000 W; or
    a.6.a.2. Having all of the following:
    a.6.a.2.a. Output power exceeding 500 W; and
    a.6.a.2.b. Spectral bandwidth less than 40 GHz; or
    a.6.b. `Multiple transverse mode' output and any of the 
following:
    a.6.b.1. `Wall-plug efficiency' exceeding 18% and output power 
exceeding 1,000 W; or
    a.6.b.2. Output power exceeding 2 kW;
    Note 1: 6A005.a.6.b does not control `multiple transverse mode', 
industrial ``lasers'' with output power exceeding 2 kW and not 
exceeding 6 kW with a total mass greater than 1,200 kg. For the 
purpose of this note, total mass includes all ``components'' 
required to operate the ``laser,'' e.g., ``laser,'' power supply, 
heat exchanger, but excludes external optics for beam conditioning 
or delivery.
    Note 2: 6A005.a.6.b does not apply to `multiple transverse 
mode', industrial ``lasers'' having any of the following:
    a. [Reserved];
    b. Output power exceeding 1 kW but not exceeding 1.6 kW and 
having a BPP exceeding 1.25 mmmrad;
    c. Output power exceeding 1.6 kW but not exceeding 2.5 kW and 
having a BPP exceeding 1.7 mmmrad;

[[Page 12123]]

    d. Output power exceeding 2.5 kW but not exceeding 3.3 kW and 
having a BPP exceeding 2.5 mmmrad;
    e. Output power exceeding 3.3 kW but not exceeding 6 kW and 
having a BPP exceeding 3.5 mmmrad;
    f. [Reserved]
    g. [Reserved]
    h. Output power exceeding 6 kW but not exceeding 8 kW and having 
a BPP exceeding 12 mmmrad; or
    i. Output power exceeding 8 kW but not exceeding 10 kW and 
having a BPP exceeding 24 mmmrad;
    a.7. Output wavelength exceeding 1,150 nm but not exceeding 
1,555 nm and any of the following:
    a.7.a. `Single transverse mode' and output power exceeding 50 W; 
or
    a.7.b. `Multiple transverse mode' and output power exceeding 80 
W;
    a.8. Output wavelength exceeding 1,555 nm but not exceeding 
1,850 nm and output power exceeding 1 W;
    a.9. Output wavelength exceeding 1,850 nm but not exceeding 
2,100 nm, and any of the following:
    a.9.a. `Single transverse mode' and output power exceeding 1 W; 
or
    a.9. b. `Multiple transverse mode' output and output power 
exceeding 120 W; or
    a.10. Output wavelength exceeding 2,100 nm and output power 
exceeding 1 W;
    b. Non-``tunable'' ``pulsed lasers'' having any of the 
following:
    b.1. Output wavelength less than 150 nm and any of the 
following:
    b.1.a. Output energy exceeding 50 mJ per pulse and ``peak 
power'' exceeding 1 W; or
    b.1.b. ``Average output power'' exceeding 1 W;
    b.2. Output wavelength of 150 nm or more but not exceeding 510 
nm and any of the following:
    b.2.a. Output energy exceeding 1.5 J per pulse and ``peak 
power'' exceeding 30 W; or
    b.2.b. ``Average output power'' exceeding 30 W;
    Note: 6A005.b.2.b does not control Argon ``lasers'' having an 
``average output power'' equal to or less than 50 W.
    b.3. Output wavelength exceeding 510 nm, but not exceeding 540 
nm and any of the following:
    b.3.a. `Single transverse mode' output and any of the following:
    b.3.a.1. Output energy exceeding 1.5 J per pulse and ``peak 
power'' exceeding 50 W; or
    b.3.a.2. ``Average output power'' exceeding 50 W; or
    b.3.b. `Multiple transverse mode' output and any of the 
following:
    b.3.b.1. Output energy exceeding 1.5 J per pulse and ``peak 
power'' exceeding 150 W; or
    b.3.b.2. ``Average output power'' exceeding 150 W;
    b.4. Output wavelength exceeding 540 nm but not exceeding 800 nm 
and any of the following:
    b.4.a. ``Pulse duration'' less than 1 ps and any of the 
following:
    b.4.a.1. Output energy exceeding 0.005 J per pulse and ``peak 
power'' exceeding 5 GW; or
    b.4.a.2. ``Average output power'' exceeding 20 W; or
    b.4.b. ``Pulse duration'' equal to or exceeding 1 ps and any of 
the following:
    b.4.b.1. Output energy exceeding 1.5 J per pulse and ``peak 
power'' exceeding 30 W; or
    b.4.b.2. ``Average output power'' exceeding 30 W;
    b.5. Output wavelength exceeding 800 nm but not exceeding 975 nm 
and any of the following:
    b.5.a. ``Pulse duration'' less than 1ps and any of the 
following:
    b.5.a.1. Output energy exceeding 0.005 J per pulse and ``peak 
power'' exceeding 5 GW; or
    b.5.a.2. `Single transverse mode' output and ``average output 
power'' exceeding 20 W;
    b.5.b. ``Pulse duration'' equal to or exceeding 1 ps and not 
exceeding 1 [mu]s and any of the following:
    b.5.b.1. Output energy exceeding 0.5 J per pulse and ``peak 
power'' exceeding 50 W;
    b.5.b.2. `Single transverse mode' output and ``average output 
power'' exceeding 20 W; or
    b.5.b.3. `Multiple transverse mode' output and ``average output 
power'' exceeding 50 W; or
    b.5.c. ``Pulse duration'' exceeding 1 [mu]s and any of the 
following:
    b.5.c.1. Output energy exceeding 2 J per pulse and ``peak 
power'' exceeding 50 W;
    b.5.c.2. `Single transverse mode' output and ``average output 
power'' exceeding 50 W; or
    b.5.c.3. `Multiple transverse mode' output and ``average output 
power'' exceeding 80 W.
    b.6. Output wavelength exceeding 975 nm but not exceeding 1,150 
nm and any of the following:
    b.6.a. ``Pulse duration'' of less than 1 ps, and any of the 
following:
    b.6.a.1. Output ``peak power'' exceeding 2 GW per pulse;
    b.6.a.2. ``Average output power'' exceeding 30 W; or
    b.6.a.3. Output energy exceeding 0.002 J per pulse;
    b.6.b. ``Pulse duration'' equal to or exceeding 1 ps and less 
than 1 ns, and any of the following:
    b.6.b.1. Output ``peak power'' exceeding 5 GW per pulse;
    b.6.b.2. ``Average output power'' exceeding 50 W; or
    b.6.b.3. Output energy exceeding 0.1 J per pulse;
    b.6.c. ``Pulse duration'' equal to or exceeding 1 ns but not 
exceeding 1 [mu]s and any of the following:
    b.6.c.1. `Single transverse mode' output and any of the 
following:
    b.6.c.1.a. ``Peak power'' exceeding 100 MW;
    b.6.c.1.b. ``Average output power'' exceeding 20 W limited by 
design to a maximum pulse repetition frequency less than or equal to 
1 kHz;
    b.6.c.1.c. `Wall-plug efficiency' exceeding 12%, ``average 
output power'' exceeding 100 W and capable of operating at a pulse 
repetition frequency greater than 1 kHz;
    b.6.c.1.d. ``Average output power'' exceeding 150 W and capable 
of operating at a pulse repetition frequency greater than 1 kHz; or
    b.6.c.1.e. Output energy exceeding 2 J per pulse; or
    b.6.c.2. `Multiple transverse mode' output and any of the 
following:
    b.6.c.2.a. ``Peak power'' exceeding 400 MW;
    b.6.c.2.b. `Wall-plug efficiency' exceeding 18% and ``average 
output power'' exceeding 500 W;
    b.6.c.2.c. ``Average output power'' exceeding 2 kW; or
    b.6.c.2.d. Output energy exceeding 4 J per pulse; or
    b.6.d. ``Pulse duration'' exceeding 1 [mu]s and any of the 
following:
    b.6.d.1. `Single transverse mode' output and any of the 
following:
    b.6.d.1.a. ``Peak power'' exceeding 500 kW;
    b.6.d.1.b. `Wall-plug efficiency' exceeding 12% and ``average 
output power'' exceeding 100 W; or
    b.6.d.1.c. ``Average output power'' exceeding 150 W; or
    b.6.d.2. `Multiple transverse mode' output and any of the 
following:
    b.6.d.2.a. ``Peak power'' exceeding 1 MW;
    b.6.d.2.b. `Wall-plug efficiency' exceeding 18% and ``average 
output power'' exceeding 500 W; or
    b.6.d.2.c. ``Average output power'' exceeding 2 kW;
    b.7. Output wavelength exceeding 1,150 nm but not exceeding 
1,555 nm and any of the following:
    b.7.a. ``Pulse duration'' not exceeding 1 [mu]s and any of the 
following:
    b.7.a.1. Output energy exceeding 0.5 J per pulse and ``peak 
power'' exceeding 50 W;
    b.7.a.2. `Single transverse mode' output and ``average output 
power'' exceeding 20 W; or
    b.7.a.3. `Multiple transverse mode' output and ``average output 
power'' exceeding 50 W; or
    b.7.b. ``Pulse duration'' exceeding 1 [mu]s and any of the 
following:
    b.7.b.1. Output energy exceeding 2 J per pulse and ``peak 
power'' exceeding 50 W;
    b.7.b.2. `Single transverse mode' output and ``average output 
power'' exceeding 50 W; or
    b.7.b.3. `Multiple transverse mode' output and ``average output 
power'' exceeding 80 W;
    b.8. Output wavelength exceeding 1,555 nm but not exceeding 
1,850 nm, and any of the following:
    b.8.a. Output energy exceeding 100 mJ per pulse and ``peak 
power'' exceeding 1 W; or
    b.8.b. ``Average output power'' exceeding 1 W;
    b.9. Output wavelength exceeding 1,850 nm but not exceeding 
2,100 nm, and any of the following:
    b.9.a. `Single transverse mode' and any of the following:
    b.9.a.1. Output energy exceeding 100 mJ per pulse and ``peak 
power'' exceeding 1 W; or
    b.9.a.2. ``Average output power'' exceeding 1 W;
    b.9.b. `Multiple transverse mode' and any of the following:
    b.9.b.1. Output energy exceeding 100 mJ per pulse and ``peak 
power'' exceeding 10 kW; or
    b.9.b.2. ``Average output power'' exceeding 120 W; or
    b.10. Output wavelength exceeding 2,100 nm and any of the 
following:

[[Page 12124]]

    b.10.a. Output energy exceeding 100 mJ per pulse and ``peak 
power'' exceeding 1 W; or
    b.10.b. ``Average output power'' exceeding 1 W;
    c. ``Tunable'' lasers having any of the following:
    c.1. Output wavelength less than 600 nm and any of the 
following:
    c.1.a. Output energy exceeding 50 mJ per pulse and ``peak 
power'' exceeding 1 W; or
    c.1.b. Average or CW output power exceeding 1W;
    Note: 6A005.c.1 does not apply to dye ``lasers'' or other liquid 
``lasers,'' having a multimode output and a wavelength of 150 nm or 
more but not exceeding 600 nm and all of the following:
    1. Output energy less than 1.5 J per pulse or a ``peak power'' 
less than 20 W; and
    2. Average or CW output power less than 20 W.
    c.2. Output wavelength of 600 nm or more but not exceeding 1,400 
nm, and any of the following:
    c.2.a. Output energy exceeding 1 J per pulse and ``peak power'' 
exceeding 20 W; or
    c.2.b. Average or CW output power exceeding 20 W; or
    c.3. Output wavelength exceeding 1,400 nm and any of the 
following:
    c.3.a. Output energy exceeding 50 mJ per pulse and ``peak 
power'' exceeding 1 W; or
    c.3.b. Average or CW output power exceeding 1 W;
    d. Other ``lasers'', not controlled by 6A005.a, 6A005.b, or 
6A005.c as follows:
    d.1. Semiconductor ``lasers'' as follows:
    Notes:
    1. 6A005.d.1 includes semiconductor ``lasers'' having optical 
output connectors (e.g., fiber optic pigtails).
    2. The control status of semiconductor ``lasers'' ``specially 
designed'' for other equipment is determined by the control status 
of the other equipment.
    d.1.a. Individual single transverse mode semiconductor 
``lasers'' having any of the following:
    d.1.a.1. Wavelength equal to or less than 1,510 nm and average 
or CW output power, exceeding 1.5 W; or
    d.1.a.2. Wavelength greater than 1,510 nm and average or CW 
output power, exceeding 500 mW;
    d.1.b. Individual `multiple-transverse mode' semiconductor 
``lasers'' having any of the following:
    d.1.b.1. Wavelength of less than 1,400 nm and average or CW 
output power, exceeding 25 W;
    d.1.b.2. Wavelength equal to or greater than 1,400 nm and less 
than 1,900 nm and average or CW output power, exceeding 2.5 W; or
    d.1.b.3. Wavelength equal to or greater than 1,900 nm and 
average or CW output power, exceeding 1 W;
    d.1.c. Individual semiconductor ``laser'' 'bars' having any of 
the following:
    d.1.c.1. Wavelength of less than 1,400 nm and average or CW 
output power, exceeding 100 W;
    d.1.c.2. Wavelength equal to or greater than 1,400 nm and less 
than 1,900 nm and average or CW output power, exceeding 25 W; or
    d.1.c.3. Wavelength equal to or greater than 1,900 nm and 
average or CW output power, exceeding 10 W;
    d.1.d. Semiconductor ``laser'' `stacked arrays' (two dimensional 
arrays) having any of the following:
    d.1.d.1. Wavelength less than 1,400 nm and having any of the 
following:
    d.1.d.1.a. Average or CW total output power less than 3 kW and 
having average or CW output `power density' greater than 500 W/
cm\2\;
    d.1.d.1.b. Average or CW total output power equal to or 
exceeding 3 kW but less than or equal to 5 kW, and having average or 
CW output `power density' greater than 350W/cm\2\;
    d.1.d.1.c. Average or CW total output power exceeding 5 kW;
    d.1.d.1.d. Peak pulsed `power density' exceeding 2,500 W/cm\2\; 
or
    Note: 6A005.d.1.d.1.d does not apply to epitaxially-fabricated 
monolithic devices.
    d.1.d.1.e. Spatially coherent average or CW total output power, 
greater than 150 W;
    d.1.d.2. Wavelength greater than or equal to 1,400 nm but less 
than 1,900 nm, and having any of the following:
    d.1.d.2.a. Average or CW total output power less than 250 W and 
average or CW output `power density' greater than 150 W/cm2;
    d.1.d.2.b. Average or CW total output power equal to or 
exceeding 250 W but less than or equal to 500 W, and having average 
or CW output `power density' greater than 50W/cm\2\;
    d.1.d.2.c. Average or CW total output power exceeding 500 W;
    d.1.d.2.d. Peak pulsed `power density' exceeding 500 W/cm\2\; or
    Note: 6A005.d.1.d.2.d does not apply to epitaxially-fabricated 
monolithic devices.
    d.1.d.2.e. Spatially coherent average or CW total output power, 
exceeding 15 W;
    d.1.d.3. Wavelength greater than or equal to 1,900 nm and having 
any of the following:
    d.1.d.3.a. Average or CW output `power density' greater than 50 
W/cm\2\;
    d.1.d.3.b. Average or CW output power greater than 10 W; or
    d.1.d.3.c. Spatially coherent average or CW total output power, 
exceeding 1.5 W; or
    d.1.d.4. At least one ``laser'' `bar' specified by 6A005.d.1.c;
    Technical Note: For the purposes of 6A005.d.1.d, 'power density' 
means the total ``laser'' output power divided by the emitter 
surface area of the `stacked array'.
    d.1.e. Semiconductor ``laser'' `stacked arrays', other than 
those specified by 6A005.d.1.d, having all of the following:
    d.1.e.1. ``Specially designed'' or modified to be combined with 
other `stacked arrays' to form a larger `stacked array'; and
    d.1.e.2. Integrated connections, common for both electronics and 
cooling;
    Note 1: `Stacked arrays', formed by combining semiconductor 
``laser'' `stacked arrays' specified by 6A005.d.1.e, that are not 
designed to be further combined or modified are specified by 
6A005.d.1.d.
    Note 2: `Stacked arrays', formed by combining semiconductor 
``laser'' `stacked arrays' specified by 6A005.d.1.e, that are 
designed to be further combined or modified are specified by 
6A005.d.1.e.
    Note 3: 6A005.d.1.e does not apply to modular assemblies of 
single `bars' designed to be fabricated into end to end stacked 
linear arrays.
    Technical Notes:
    1. Semiconductor ``lasers'' are commonly called ``laser'' 
diodes.
    2. A `bar' (also called a semiconductor ``laser'' `bar', a 
``laser'' diode `bar' or diode `bar') consists of multiple 
semiconductor ``lasers'' in a one dimensional array.
    3. A `stacked array' consists of multiple `bars' forming a two 
dimensional array of semiconductor ``lasers''.
    d.2. Carbon monoxide (CO) ``lasers'' having any of the 
following:
    d.2.a. Output energy exceeding 2 J per pulse and ``peak power'' 
exceeding 5 kW; or
    d.2.b. Average or CW output power, exceeding 5 kW;
    d.3. Carbon dioxide (CO2) ``lasers'' having any of 
the following:
    d.3.a. CW output power exceeding 15 kW;
    d.3.b. Pulsed output with ``pulse duration'' exceeding 10 [mu]s 
and any of the following:
    d.3.b.1. ``Average output power'' exceeding 10 kW; or
    d.3.b.2. ``Peak power'' exceeding 100 kW; or
    d.3.c. Pulsed output with a ``pulse duration'' equal to or less 
than 10 [mu]s and any of the following:
    d.3.c.1. Pulse energy exceeding 5 J per pulse; or
    d.3.c.2. ``Average output power'' exceeding 2.5 kW;
    d.4. Excimer ``lasers'' having any of the following:
    d.4.a. Output wavelength not exceeding 150 nm and any of the 
following:
    d.4.a.1. Output energy exceeding 50 mJ per pulse; or
    d.4.a.2. ``Average output power'' exceeding 1 W;
    d.4.b. Output wavelength exceeding 150 nm but not exceeding 190 
nm and any of the following:
    d.4.b.1. Output energy exceeding 1.5 J per pulse; or
    d.4.b.2. ``Average output power'' exceeding 120 W;
    d.4.c. Output wavelength exceeding 190 nm but not exceeding 360 
nm and any of the following:
    d.4.c.1. Output energy exceeding 10 J per pulse; or
    d.4.c.2. ``Average output power'' exceeding 500 W; or
    d.4.d. Output wavelength exceeding 360 nm and any of the 
following:
    d.4.d.1. Output energy exceeding 1.5 J per pulse; or
    d.4.d.2. ``Average output power'' exceeding 30 W;
    Note: For excimer ``lasers'' ``specially designed'' for 
lithography equipment, see 3B001.
    d.5. ``Chemical lasers'' as follows:
    d.5.a. Hydrogen Fluoride (HF) ``lasers';
    d.5.b. Deuterium Fluoride (DF) ``lasers'';
    d.5.c. `Transfer lasers' as follows:
    d.5.c.1. Oxygen Iodine (O2-I) ``lasers'';
    d.5.c.2. Deuterium Fluoride-Carbon dioxide (DF-CO2) 
``lasers'';
    Technical Note: `Transfer lasers' are ``lasers'' in which the 
lasing species are excited through the transfer of energy by 
collision of a non-lasing atom or molecule with a lasing atom or 
molecule species.

[[Page 12125]]

    d.6. `Non-repetitive pulsed' Neodymium (Nd) glass ``lasers'' 
having any of the following:
    d.6.a. A ``pulse duration'' not exceeding 1 [mu]s and output 
energy exceeding 50 J per pulse; or
    d.6.b. A ``pulse duration'' exceeding 1 [mu]s and output energy 
exceeding 100 J per pulse;
    e. ``Components'' as follows:
    e.1. Mirrors cooled either by `active cooling' or by heat pipe 
cooling;
    Technical Note: `Active cooling' is a cooling technique for 
optical ``components'' using flowing fluids within the subsurface 
(nominally less than 1 mm below the optical surface) of the optical 
component to remove heat from the optic.
    e.2. Optical mirrors or transmissive or partially transmissive 
optical or electro-optical-''components,'' other than fused tapered 
fiber combiners and Multi-Layer Dielectric gratings (MLDs), 
``specially designed'' for use with controlled ``lasers'';
    Note to 6A005.e.2: Fiber combiners and MLDs are specified by 
6A005.e.3.
    e.3. Fiber ``laser'' ``components'' as follows:
    e.3.a. Multimode to multimode fused tapered fiber combiners 
having all of the following:
    e.3.a.1. An insertion loss better (less) than or equal to 0.3 dB 
maintained at a rated total average or CW output power (excluding 
output power transmitted through the single mode core if present) 
exceeding 1,000 W; and
    e.3.a.2. Number of input fibers equal to or greater than 3;
    e.3.b. Single mode to multimode fused tapered fiber combiners 
having all of the following:
    e.3.b.1. An insertion loss better (less) than 0.5 dB maintained 
at a rated total average or CW output power exceeding 4,600 W;
    e.3.b.2. Number of input fibers equal to or greater than 3; and
    e.3.b.3. Having any of the following:
    e.3.b.3.a. A Beam Parameter Product (BPP) measured at the output 
not exceeding 1.5 mm mrad for a number of input fibers less than or 
equal to 5; or
    e.3.b.3.b. A BPP measured at the output not exceeding 2.5 mm 
mrad for a number of input fibers greater than 5;
    e.3.c. MLDs having all of the following:
    e.3.c.1. Designed for spectral or coherent beam combination of 5 
or more fiber ``lasers;'' and
    e.3.c.2. CW ``Laser'' Induced Damage Threshold (LIDT) greater 
than or equal to 10 kW/cm\2\;
    f. Optical equipment as follows:
    N.B.: For shared aperture optical elements, capable of operating 
in ``Super-High Power Laser'' (``SHPL'') applications, see the U.S. 
Munitions List (22 CFR part 121).
    f.1. [Reserved]
    N.B.: For items previously specified by 6A005.f.1, see 6A004.f.
    f.2. ``Laser'' diagnostic equipment ``specially designed'' for 
dynamic measurement of ``SHPL'' system angular beam steering errors 
and having an angular ``accuracy'' of 10 [mu]rad (microradians) or 
less (better);
    f.3. Optical equipment and ``components'', ``specially 
designed'' for coherent beam combination in a phased-array ``SHPL'' 
system and having any of the following:
    f.3.a. An ``accuracy'' of 0.1 [micro]m or less, for wavelengths 
greater than 1 [micro]m; or
    f.3.b. An ``accuracy'' of [lambda]/10 or less (better) at the 
designed wavelength, for wavelengths equal to or less than 1 
[micro]m;
    f.4. Projection telescopes ``specially designed'' for use with 
``SHPL'' systems;
    g. `Laser acoustic detection equipment' having all of the 
following:
    g.1. CW ``laser'' output power greater than or equal to 20 mW;
    g.2. ``Laser'' frequency stability equal to or better (less) 
than 10 MHz;
    g.3. ``Laser'' wavelengths equal to or exceeding 1,000 nm but 
not exceeding 2,000 nm;
    g.4. Optical system resolution better (less) than 1 nm; and
    g.5. Optical Signal to Noise ratio equal or exceeding to 10\3\.
    Technical Note: `Laser acoustic detection equipment' is 
sometimes referred to as a ``Laser'' Microphone or Particle Flow 
Detection Microphone.
* * * * *
6A008 Radar systems, equipment and assemblies, having any of the 
following (see List of Items Controlled), and ``specially designed'' 
``components'' therefor.

License Requirements

Reason for Control: NS, MT, RS, AT

 
                                            Country chart (see Supp. No.
                Control(s)                         1 to part 738)
 
NS applies to entire entry................  NS Column 2.
MT applies to items that are designed for   MT Column 1.
 airborne applications and that are usable
 in systems controlled for MT reasons.
RS applies to 6A008.j.1...................  RS Column 1.
AT applies to entire entry................  AT Column 1.
 

Reporting Requirements

See Sec.  743.1 of the EAR for reporting requirements for exports 
under License Exceptions, and Validated End-User authorizations.

List Based License Exceptions (See Part 740 for a Description of All 
License Exceptions)

LVS: $5000; N/A for MT and for 6A008.j.1.
GBS: Yes, for 6A008.b, .c, and l.1 only

Special Conditions for STA

STA: License Exception STA may not be used to ship any commodity in 
6A008.d, 6A008.h or 6A008.k to any of the destinations listed in 
Country Group A:6 (See Supplement No.1 to part 740 of the EAR).

List of Items Controlled

Related Controls: (1) See also ECCNs 6A108 and 6A998. ECCN 6A998 
controls, inter alia, the Light Detection and Ranging (LIDAR) 
equipment excluded by the note to paragraph j of this ECCN (6A008). 
(2) See USML Category XII(b) for certain LIDAR, Laser Detection and 
Ranging (LADAR), or range-gated systems subject to the ITAR.
Related Definitions: N/A
Items:

    Note: 6A008 does not control:

--Secondary surveillance radar (SSR);
--Civil Automotive Radar;
--Displays or monitors used for air traffic control (ATC);
--Meteorological (weather) radar;
--Precision Approach Radar (PAR) equipment conforming to ICAO 
standards and employing electronically steerable linear (1-
dimensional) arrays or mechanically positioned passive antennas.

    a. Operating at frequencies from 40 GHz to 230 GHz and having 
any of the following:
    a.1. An average output power exceeding 100 mW; or
    a.2. Locating ``accuracy'' of 1 m or less (better) in range and 
0.2 degree or less (better) in azimuth;
    b. A tunable bandwidth exceeding 6.25% of the 
`center operating frequency';
    Technical Note: The `center operating frequency' equals one half 
of the sum of the highest plus the lowest specified operating 
frequencies.
    c. Capable of operating simultaneously on more than two carrier 
frequencies;
    d. Capable of operating in synthetic aperture (SAR), inverse 
synthetic aperture (ISAR) radar mode, or sidelooking airborne (SLAR) 
radar mode;
    e. Incorporating electronically scanned array antennae;
    Technical Note: Electronically scanned array antennae are also 
known as electronically steerable array antennae.
    f. Capable of heightfinding non-cooperative targets;
    g. ``Specially designed'' for airborne (balloon or airframe 
mounted) operation and having Doppler ``signal processing'' for the 
detection of moving targets;
    h. Employing processing of radar signals and using any of the 
following:
    h.1. ``Radar spread spectrum'' techniques; or
    h.2. ``Radar frequency agility'' techniques;
    i. Providing ground-based operation with a maximum `instrumented 
range' exceeding 185 km;
    Note: 6A008.i does not control:
    a. Fishing ground surveillance radar;
    b. Ground radar equipment ``specially designed'' for en route 
air traffic control, and having all of the following:
    1. A maximum `instrumented range' of 500 km or less;
    2. Configured so that radar target data can be transmitted only 
one way from the radar site to one or more civil ATC centers;
    3. Contains no provisions for remote control of the radar scan 
rate from the en route ATC center; and
    4. Permanently installed;
    c. Weather balloon tracking radars.
    Technical Note: For the purposes of 6A008.i, `instrumented 
range' is the specified unambiguous display range of a radar.
    j. Being ``laser'' radar or Light Detection and Ranging (LIDAR) 
equipment and having any of the following:

[[Page 12126]]

    j.1. ``Space-qualified'';
    j.2. Employing coherent heterodyne or homodyne detection 
techniques and having an angular resolution of less (better) than 20 
[mu]rad (microradians); or
    j.3. Designed for carrying out airborne bathymetric littoral 
surveys to International Hydrographic Organization (IHO) Order 1a 
Standard (5th Edition February 2008) for Hydrographic Surveys or 
better, and using one or more ``lasers'' with a wavelength exceeding 
400 nm but not exceeding 600 nm;
    Note 1: LIDAR equipment ``specially designed'' for surveying is 
only specified by 6A008.j.3.
    Note 2: 6A008.j does not apply to LIDAR equipment ``specially 
designed'' for meteorological observation.
    Note 3: Parameters in the IHO Order 1a Standard 5th Edition 
February 2008 are summarized as follows:

Horizontal Accuracy (95% Confidence Level) = 5 m + 5% of depth.
Depth Accuracy for Reduced Depths (95% confidence level) = [radic](a2+(b*d)2)
where:

a = 0.5 m = constant depth error, i.e. the sum of all constant depth 
errors
b = 0.013 = factor of depth dependent error
b*d = depth dependent error, i.e., the sum of all depth dependent 
errors
d = depth

    Feature Detection = Cubic features 2 m in depths up 
to 40 m; 10% of depth beyond 40 m.
    k. Having ``signal processing'' sub-systems using ``pulse 
compression'' and having any of the following:
    k.1. A ``pulse compression'' ratio exceeding 150; or
    k.2. A compressed pulse width of less than 200 ns; or
    Note: 6A008.k.2 does not apply to two dimensional `marine radar' 
or `vessel traffic service' radar, having all of the following:
    a. ``Pulse compression'' ratio not exceeding 150;
    b. Compressed pulse width of greater than 30 ns;
    c. Single and rotating mechanically scanned antenna;
    d. Peak output power not exceeding 250 W; and
    e. Not capable of ``frequency hopping''.
    l. Having data processing sub-systems and having any of the 
following:
    l.1. `Automatic target tracking' providing, at any antenna 
rotation, the predicted target position beyond the time of the next 
antenna beam passage; or
    Note: 6A008.l.1 does not control conflict alert capability in 
ATC systems, or `marine radar'.
    Technical Note: `Automatic target tracking' is a processing 
technique that automatically determines and provides as output an 
extrapolated value of the most probable position of the target in 
real time.
    l.2. [Reserved]
    l.3. [Reserved]
    l.4. Configured to provide superposition and correlation, or 
fusion, of target data within six seconds from two or more 
`geographically dispersed' radar sensors to improve the aggregate 
performance beyond that of any single sensor specified by 6A008.f, 
or 6A008.i.
    Technical Note: Sensors are considered `geographically 
dispersed' when each location is distant from any other more than 
1,500 m in any direction. Mobile sensors are always considered 
`geographically dispersed'.
    N.B.: See also the U.S. Munitions List (22 CFR part 121).
    Note: 6A008.l does not apply to systems, equipment and 
assemblies designed for `vessel traffic services'.
    Technical Notes:
    1. For the purposes of 6A008, `marine radar' is a radar that is 
designed to navigate safely at sea, inland waterways or near-shore 
environments.
    2. For the purposes of 6A008, `vessel traffic service' is a 
vessel traffic monitoring and control service similar to air traffic 
control for ``aircraft.''
* * * * *
6D003 Other ``software'' as follows (see List of Items Controlled).

License Requirements

Reason for Control: NS, RS, AT

 
                                            Country chart (see Supp. No.
                Control(s)                         1 to part 738)
 
NS applies to entire entry................  NS Column 1.
RS applies to paragraph c.................  RS Column 1.
AT applies to entire entry................  AT Column 1.
 

Reporting Requirements

See Sec.  743.1 of the EAR for reporting requirements for exports 
under License Exceptions, and Validated End-User authorizations.

List Based License Exceptions (See Part 740 for a Description of All 
License Exceptions)

TSR: Yes, except for 6D003.c and exports or reexports to 
destinations outside of those countries listed in Country Group A:5 
(See Supplement No. 1 to part 740 of the EAR) of ``software'' for 
items controlled by 6D003.a.

Special Conditions for STA

STA: License Exception STA may not be used to ship or transmit 
software in 6D003.a to any of the destinations listed in Country 
Group A:6 (See Supplement No. 1 to part 740 of the EAR).

List of Items Controlled

Related Controls: See also ECCNs 6D103, 6D991, and 6D993.
Related Definitions: N/A
Items:

Acoustics

    a. ``Software'' as follows:
    a.1. ``Software'' ``specially designed'' for acoustic beam 
forming for the ``real-time processing'' of acoustic data for 
passive reception using towed hydrophone arrays;
    a.2. ``Source code'' for the ``real-time processing'' of 
acoustic data for passive reception using towed hydrophone arrays;
    a.3. ``Software'' ``specially designed'' for acoustic beam 
forming for the ``real-time processing'' of acoustic data for 
passive reception using bottom or bay cable systems;
    a.4. ``Source code'' for the ``real-time processing'' of 
acoustic data for passive reception using bottom or bay cable 
systems;
    a.5. ``Software'' or ``source code'', ``specially designed'' for 
all of the following:
    a.5.a. ``Real-time processing'' of acoustic data from sonar 
systems controlled by 6A001.a.1.e; and
    a.5.b. Automatically detecting, classifying and determining the 
location of divers or swimmers;
    N.B.: For diver detection ``software'' or ``source code'', 
``specially designed'' or modified for military use, see the U.S. 
Munitions List of the International Traffic in Arms Regulations 
(ITAR) (22 CFR part 121).
    b. Optical sensors. None.

Cameras

    c. ``Software'' designed or modified for cameras incorporating 
``focal plane arrays'' specified by 6A002.a.3.f and designed or 
modified to remove a frame rate restriction and allow the camera to 
exceed the frame rate specified in 6A003.b.4 Note 3.a;

Optics

    d. ``Software'' specially designed to maintain the alignment and 
phasing of segmented mirror systems consisting of mirror segments 
having a diameter or major axis length equal to or larger than 1 m;
    e. Lasers. None.

Magnetic and Electric Field Sensors

    f. ``Software'' as follows:
    f.1. ``Software'' ``specially designed'' for magnetic and 
electric field ``compensation systems'' for magnetic sensors 
designed to operate on mobile platforms;
    f.2. ``Software'' ``specially designed'' for magnetic and 
electric field anomaly detection on mobile platforms;
    f.3. ``Software'' ``specially designed'' for ``real-time 
processing'' of electromagnetic data using underwater 
electromagnetic receivers specified by 6A006.e;
    f.4. ``Source code'' for ``real-time processing'' of 
electromagnetic data using underwater electromagnetic receivers 
specified by 6A006.e;

Gravimeters

    g. ``Software'' ``specially designed'' to correct motional 
influences of gravity meters or gravity gradiometers;

Radar

    h. ``Software'' as follows:
    h.1. Air Traffic Control (ATC) ``software'' designed to be 
hosted on general purpose computers located at Air Traffic Control 
centers and capable of accepting radar target data from more than 
four primary radars;
    h.2. ``Software'' for the design or ``production'' of radomes 
having all of the following:
    h.2.a. ``Specially designed'' to protect the ``electronically 
scanned array antennae'' specified by 6A008.e; and
    h.2.b. Resulting in an antenna pattern having an `average side 
lobe level' more than 40 dB below the peak of the main beam level.
    Technical Note: `Average side lobe level' in 6D003.h.2.b is 
measured over the entire

[[Page 12127]]

array excluding the angular extent of the main beam and the first 
two side lobes on either side of the main beam.
* * * * *

Category 7--Navigation and Avionics

* * * * *
7D003 Other ``software'' as follows (see List of Items Controlled).

License Requirements

Reason for Control: NS, MT, AT

 
                                            Country chart (see Supp. No.
                Control(s)                         1 to part 738)
 
NS applies to entire entry................  NS Column 1.
MT applies to ``software'' for equipment    MT Column 1.
 controlled for MT reasons. MT does not
 apply to ``software'' for equipment
 controlled by 7A008.
AT applies to entire entry................  AT Column 1.
 

Reporting Requirements

See Sec.  743.1 of the EAR for reporting requirements for exports 
under License Exceptions, and Validated End-User authorizations.

List Based License Exceptions (See Part 740 for a Description of All 
License Exceptions)

TSR: N/A

Special Conditions for STA

STA: License Exception STA may not be used to ship or transmit 
software in 7D003.a or .b to any of the destinations listed in 
Country Group A:6 (See Supplement No. 1 to part 740 of the EAR).

List of Items Controlled

Related Controls: See also 7D103 and 7D994.
Related Definitions: `Data-Based Referenced Navigation' (`DBRN') 
systems are systems which use various sources of previously measured 
geo-mapping data integrated to provide accurate navigation 
information under dynamic conditions. Data sources include 
bathymetric maps, stellar maps, gravity maps, magnetic maps or 3-D 
digital terrain maps.
Items:

    a. ``Software'' ``specially designed'' or modified to improve 
the operational performance or reduce the navigational error of 
systems to the levels controlled by 7A003, 7A004 or 7A008;
    b. ``Source code'' for hybrid integrated systems which improves 
the operational performance or reduces the navigational error of 
systems to the level controlled by 7A003 or 7A008 by continuously 
combining heading data with any of the following:
    b.1. Doppler radar or sonar velocity data;
    b.2. ``Satellite navigation system'' reference data; or
    b.3. Data from `Data-Based Referenced Navigation' (`DBRN'') 
systems;
    c. [Reserved]
    d. [Reserved]
    N.B. For flight control ``source code,'' see 7D004.
    e. Computer-Aided-Design (CAD) ``software'' ``specially 
designed'' for the ``development'' of ``active flight control 
systems'', helicopter multi-axis fly-by-wire or fly-by-light 
controllers or helicopter ``circulation-controlled anti-torque or 
circulation-controlled direction control systems'', whose 
``technology'' is controlled by 7E004.b.1, 7E004.b.3 to b.5, 
7E004.b.7 to b.8, 7E004.c.1 or 7E004.c.2.
* * * * *

Category 9--Aerospace and Propulsion

* * * * *
9A004 Space launch vehicles and ``spacecraft,'' ``spacecraft 
buses'', ``spacecraft payloads'', ``spacecraft'' on-board systems or 
equipment, terrestrial equipment, air-launch platforms, and ``sub-
orbital craft'', as follows (see List of Items Controlled).

License Requirements

Reason for Control: NS and AT

 
                                            Country chart (see Supp. No.
                Control(s)                         1 to part 738)
 
NS applies to 9A004.g, .u, .v, .w and .x..  NS Column 1.
AT applies to 9A004.g, .u, .v, .w, .x and   AT Column 1.
 .y.
 

License Requirement Note: 9A004.b through .f, and .h are controlled 
under ECCN 9A515.

List Based License Exceptions (See Part 740 for a Description of All 
License Exceptions)

LVS: N/A
GBS: N/A

List of Items Controlled

Related Controls: (1) See also 9A104, 9A515, and 9B515. (2) See 
ECCNs 9E001 (``development'') and 9E002 (``production'') for 
technology for items controlled by this entry. (3) See USML 
Categories IV for the space launch vehicles and XV for other 
spacecraft that are ``subject to the ITAR'' (see 22 CFR parts 120 
through 130).
Related Definition: N/A
Items:

    a. Space launch vehicles;
    b. ``Spacecraft'';
    c. ``Spacecraft buses'';
    d. ``Spacecraft payloads'' incorporating items specified by 
3A001.b.1.a.4, 3A002.g, 5A001.a.1, 5A001.b.3, 5A002.c, 5A002.e, 
6A002.a.1, 6A002.a.2, 6A002.b, 6A002.d, 6A003.b, 6A004.c, 6A004.e, 
6A008.d, 6A008.e, 6A008.k, 6A008.l or 9A010.c;
    e. On-board systems or equipment, specially designed for 
``spacecraft'' and having any of the following functions:
    e.1. `Command and telemetry data handling';
    Note: For the purpose of 9A004.e.1, `command and telemetry data 
handling' includes bus data management, storage, and processing.
    e.2. `Payload data handling'; or
    Note: For the purpose of 9A004.e.2, `payload data handling' 
includes payload data management, storage, and processing.
    e.3. `Attitude and orbit control';
    Note: For the purpose of 9A004.e.3, `attitude and orbit control' 
includes sensing and actuation to determine and control the position 
and orientation of a ``spacecraft''.
    N.B.: Equipment specially designed for military use is ``subject 
to the ITAR''. See 22 CFR parts 120 through 130.
    f. Terrestrial equipment specially designed for ``spacecraft'', 
as follows:
    f.1. Telemetry and telecommand equipment ``specially designed'' 
for any of the following data processing functions:
    f.1.a. Telemetry data processing of frame synchronization and 
error corrections, for monitoring of operational status (also known 
as health and safe status) of the ``spacecraft bus''; or
    f.1.b. Command data processing for formatting command data being 
sent to the ``spacecraft'' to control the ``spacecraft bus'';
    f.2. Simulators ``specially designed'' for `verification of 
operational procedures' of ``spacecraft''.
    Technical Note: For the purposes of 9A004.f.2, `verification of 
operational procedures' is any of the following:
    1. Command sequence confirmation;
    2. Operational training;
    3. Operational rehearsals; or
    4. Operational analysis.
    g. ``Aircraft'' ``specially designed'' or modified to be air-
launch platforms for space launch vehicles or ``sub-orbital craft''.
    h. ``Sub-orbital craft''.
    i. through t. [RESERVED]
    u. The James Webb Space Telescope (JWST) being developed, 
launched, and operated under the supervision of the U.S. National 
Aeronautics and Space Administration (NASA).
    v. ``Parts,'' ``components,'' ``accessories'' and 
``attachments'' that are ``specially designed'' for the James Webb 
Space Telescope and that are not:
    v.1. Enumerated or controlled in the USML;
    v.2. Microelectronic circuits;
    v.3. Described in ECCN 7A004 or 7A104; or
    v.4. Described in an ECCN containing ``space-qualified'' as a 
control criterion (See ECCN 9A515.x.4).
    w. The International Space Station being developed, launched, 
and operated under the supervision of the U.S. National Aeronautics 
and Space Administration.
    x. ``Parts,'' ``components,'' ``accessories'' and 
``attachments'' that are ``specially designed'' for the 
International Space Station.
    y. Items that would otherwise be within the scope of ECCN 
9A004.v or .x but that have been identified in an interagency-
cleared commodity classification (CCATS) pursuant to Sec.  748.3(e) 
as warranting control in 9A004.y.
* * * * *
9B001 Manufacturing equipment, tooling or fixtures, as follows (See 
List of Items Controlled).

License Requirements

Reason for Control: NS, MT, AT

[[Page 12128]]



 
                                            Country chart (see Supp. No.
                Control(s)                         1 to part 738)
 
NS applies to entire entry................  NS Column 1.
MT applies to equipment for engines         MT Column 1.
 controlled under 9A001 for MT reasons and
 for engines controlled under 9A101.
AT applies to entire entry................  AT Column 1.
 

Reporting Requirements

See Sec.  743.1 of the EAR for reporting requirements for exports 
under License Exceptions, and Validated End-User authorizations.

List Based License Exceptions (See Part 740 for a Description of All 
License Exceptions)

LVS: $5000, except N/A for MT
GBS: Yes, except N/A for MT

Special Conditions for STA

STA: License Exception STA may not be used to ship commodities in 
9B001 to any of the destinations listed in Country Group A:6 (See 
Supplement No.1 to part 740 of the EAR).

List of Items Controlled

Related Controls: For ``specially designed'' production equipment of 
systems, sub-systems, ``parts'' and ``components'' controlled by 
9A005 to 9A009, 9A011, 9A101, 9A105 to 9A109, 9A111, and 9A116 to 
9A119 usable in ``missiles'' see 9B115. See also 9B991.
Related Definitions: N/A
Items:
    a. Directional solidification or single crystal casting 
equipment designed for ``superalloys'';
    b. Casting tooling, ``specially designed'' for manufacturing gas 
turbine engine blades, vanes or ``tip shrouds'', manufactured from 
refractory metals or ceramics, as follows:
    b.1. Cores;
    b.2. Shells (moulds);
    b.3. Combined core and shell (mould) units;
    c. Directional-solidification or single-crystal additive-
manufacturing equipment designed for ``superalloys''.
* * * * *
9E003 Other ``technology'' as follows (see List of Items 
Controlled).

License Requirements

    Reason for Control: NS, SI, AT

 
                                            Country chart (see Supp. No.
                Control(s)                         1 to part 738)
 
NS applies to entire entry................  NS Column 1.
SI applies to 9E003.a.1 through a.8, .h,    See Sec.   742.14 of the EAR
 .i, and .k.                                 for additional information.
AT applies to entire entry................  AT Column 1.
 

Reporting Requirements

    See Sec.  743.1 of the EAR for reporting requirements for 
exports under License Exceptions, and Validated End-User 
authorizations.

List Based License Exceptions (See Part 740 for a Description of All 
License Exceptions)

TSR: N/A

Special Conditions for STA

STA: License Exception STA may not be used to ship or transmit any 
technology in 9E003.a.1 to a.5, 9E003.c., 9E003.h, or 9E003.i (other 
than technology for fan or power turbines), to any of the 
destinations listed in Country Group A:6 (See Supplement No.1 to 
part 740 of the EAR).

List of Items Controlled

Related Controls: (1) Hot section ``technology'' specifically 
designed, modified, or equipped for military uses or purposes, or 
developed principally with U.S. Department of Defense funding, is 
``subject to the ITAR'' (see 22 CFR parts 120 through 130). (2) 
``Technology'' is subject to the EAR when actually applied to a 
commercial ``aircraft'' engine program. Exporters may seek to 
establish commercial application either on a case-by-case basis 
through submission of documentation demonstrating application to a 
commercial program in requesting an export license from the 
Department of Commerce in respect to a specific export, or in the 
case of use for broad categories of ``aircraft,'' engines, ``parts'' 
or ``components,'' a commodity jurisdiction determination from the 
Department of State.
Related Definitions: N/A
Items:

    a. ``Technology'' ``required'' for the ``development'' or 
``production'' of any of the following gas turbine engine ``parts,'' 
``components'' or systems:
    a.1. Gas turbine blades, vanes or ``tip shrouds'', made from 
Directionally Solidified (DS) or Single Crystal (SC) alloys and 
having (in the 001 Miller Index Direction) a stress-rupture life 
exceeding 400 hours at 1,273 K (1,000[deg]C) at a stress of 200 MPa, 
based on the average property values;
    Technical Note: For the purposes of 9E003.a.1, stress-rupture 
life testing is typically conducted on a test specimen.
    a.2. Combustors having any of the following:
    a.2.a. `Thermally decoupled liners' designed to operate at 
`combustor exit temperature' exceeding 1,883 K (1,610 [deg]C);
    a.2.b. Non-metallic liners;
    a.2.c. Non-metallic shells; or
    a.2.d. Liners designed to operate at `combustor exit 
temperature' exceeding 1,883 K (1,610 [deg]C) and having holes that 
meet the parameters specified by 9E003.c;
    Note: The ``required'' ``technology'' for holes in 9E003.a.2 is 
limited to the derivation of the geometry and location of the holes.
    Technical Notes:
    1. `Thermally decoupled liners' are liners that feature at least 
a support structure designed to carry mechanical loads and a 
combustion facing structure designed to protect the support 
structure from the heat of combustion. The combustion facing 
structure and support structure have independent thermal 
displacement (mechanical displacement due to thermal load) with 
respect to one another, i.e., they are thermally decoupled.
    2. `Combustor exit temperature' is the bulk average gas path 
total (stagnation) temperature between the combustor exit plane and 
the leading edge of the turbine inlet guide vane (i.e., measured at 
engine station T40 as defined in SAE ARP 755A) when the engine is 
running in a ``steady state mode'' of operation at the certificated 
maximum continuous operating temperature.
    N.B.: See 9E003.c for ``technology'' ``required'' for 
manufacturing cooling holes.
    a.3. ``Parts'' or ``components,'' that are any of the following:
    a.3.a. Manufactured from organic ``composite'' materials 
designed to operate above 588 K (315 [deg]C);
    a.3.b. Manufactured from any of the following:
    a.3.b.1. Metal ``matrix'' ``composites'' reinforced by any of 
the following:
    a.3.b.1.a. Materials controlled by 1C007;
    a.3.b.1.b. ``Fibrous or filamentary materials'' specified by 
1C010; or
    a.3.b.1.c. Aluminides specified by 1C002.a; or
    a.3.b.2. Ceramic ``matrix'' ``composites'' specified by 1C007; 
or
    a.3.c. Stators, vanes, blades, tip seals (shrouds), rotating 
blings, rotating blisks or `splitter ducts', that are all of the 
following:
    a.3.c.1. Not specified in 9E003.a.3.a;
    a.3.c.2. Designed for compressors or fans; and
    a.3.c.3. Manufactured from material controlled by 1C010.e with 
resins controlled by 1C008;
    Technical Note: A `splitter duct' performs the initial 
separation of the air-mass flow between the bypass and core sections 
of the engine.
    a.4. Uncooled turbine blades, vanes or ``tip shrouds'' designed 
to operate at a ``gas path temperature'' of 1,373 K (1,100 [deg]C) 
or more;
    a.5. Cooled turbine blades, vanes or ``tip shrouds'', other than 
those described in 9E003.a.1, designed to operate at a `gas path 
temperature' of 1,693 K (1,420 [deg]C) or more;
    Technical Note: ``Gas path temperature'' is the bulk average gas 
path total (stagnation) temperature at the leading-edge plane of the 
turbine component when the engine is running in a ``steady state 
mode'' of operation at the certificated or specified maximum 
continuous operating temperature.
    a.6. Airfoil-to-disk blade combinations using solid state 
joining;
    a.7. [Reserved]
    a.8. `Damage tolerant' gas turbine engine rotor ``parts'' or 
``components'' using powder metallurgy materials controlled by 
1C002.b; or
    Technical Note: ``Damage tolerant'' ``parts'' and ``components'' 
are designed using methodology and substantiation to predict and 
limit crack growth.
    a.9. [Reserved]
    N.B.: For ``FADEC systems'', see 9E003.h.
    a.10. [Reserved]
    N.B.: For adjustable flow path geometry, see 9E003.i.

[[Page 12129]]

    a.11. `Fan blades' having all of the following:
    a.11.a. 20% or more of the total volume being one or more closed 
cavities containing vacuum or gas only; and
    a.11.b. One or more closed cavities having a volume of 5 cm\3\ 
or larger;
    Technical Note: For the purposes of 9E003.a.11, a `fan blade' is 
the aerofoil portion of the rotating stage or stages, which provide 
both compressor and bypass flow in a gas turbine engine.
    b. ``Technology'' ``required'' for the ``development'' or 
``production'' of any of the following:
    b.1. Wind tunnel aero-models equipped with non-intrusive sensors 
capable of transmitting data from the sensors to the data 
acquisition system; or
    b.2. ``Composite'' propeller blades or prop-fans, capable of 
absorbing more than 2,000 kW at flight speeds exceeding Mach 0.55;
    c. ``Technology'' ``required'' for manufacturing cooling holes, 
in gas turbine engine ``parts'' or ``components'' incorporating any 
of the ``technologies'' specified by 9E003.a.1, 9E003.a.2, or 
9E003.a.5, and having any of the following:
    c.1. Having all of the following:
    c.1.a. Minimum ``cross-sectional area'' less than 0.45 mm\2\;
    c.1.b. ``Hole shape ratio'' greater than 4.52; and
    c.1.c. ``Incidence angle'' equal to or less than 25 [deg]; or
    c.2. Having all of the following:
    c.2.a. Minimum ``cross-sectional area'' less than 0.12 mm\2\;
    c.2.b. ``Hole shape ratio'' greater than 5.65; and
    c.2.c. ``Incidence angle'' more than 25 [deg];
    Note: 9E003.c does not apply to ``technology'' for manufacturing 
constant radius cylindrical holes that are straight through and 
enter and exit on the external surfaces of the component.
    Technical Notes:
    1. For the purposes of 9E003.c, the ``cross-sectional area'' is 
the area of the hole in the plane perpendicular to the hole axis.
    2. For the purposes of 9E003.c, ``hole shape ratio'' is the 
nominal length of the axis of the hole divided by the square root of 
its minimum 'cross-sectional area'.
    3. For the purposes of 9E003.c, ``incidence angle'' is the acute 
angle measured between the plane tangential to the airfoil surface 
and the hole axis at the point where the hole axis enters the 
airfoil surface.
    4. Techniques for manufacturing holes in 9E003.c include 
``laser'' beam machining, water jet machining, Electro-Chemical 
Machining (ECM) or Electrical Discharge Machining (EDM).
    d. ``Technology'' ``required'' for the ``development'' or 
``production'' of helicopter power transfer systems or tilt rotor or 
tilt wing ``aircraft'' power transfer systems;
    e. ``Technology'' for the ``development'' or ``production'' of 
reciprocating diesel engine ground vehicle propulsion systems having 
all of the following:
    e.1. `Box volume' of 1.2 m\3\ or less;
    e.2. An overall power output of more than 750 kW based on 80/
1269/EEC, ISO 2534 or national equivalents; and
    e.3. Power density of more than 700 kW/m\3\ of `box volume';
    Technical Note: ``Box volume'' is the product of three 
perpendicular dimensions measured in the following way:
    Length: The length of the crankshaft from front flange to 
flywheel face;
    Width: The widest of any of the following:
    a. The outside dimension from valve cover to valve cover;
    b. The dimensions of the outside edges of the cylinder heads; or
    c. The diameter of the flywheel housing;
    Height: The largest of any of the following:
    a. The dimension of the crankshaft center-line to the top plane 
of the valve cover (or cylinder head) plus twice the stroke; or
    b. The diameter of the flywheel housing.
    f. ``Technology'' ``required'' for the ``production'' of 
``specially designed'' ``parts'' or ``components'' for high output 
diesel engines, as follows:
    f.1. ``Technology'' ``required'' for the ``production'' of 
engine systems having all of the following ``parts'' and 
``components'' employing ceramics materials controlled by 1C007:
    f.1.a. Cylinder liners;
    f.1.b. Pistons;
    f.1.c. Cylinder heads; and
    f.1.d. One or more other ``part'' or ``component'' (including 
exhaust ports, turbochargers, valve guides, valve assemblies or 
insulated fuel injectors);
    f.2. ``Technology'' ``required'' for the ``production'' of 
turbocharger systems with single-stage compressors and having all of 
the following:
    f.2.a. Operating at pressure ratios of 4:1 or higher;
    f.2.b. Mass flow in the range from 30 to 130 kg per minute; and
    f.2.c. Variable flow area capability within the compressor or 
turbine sections;
    f.3. ``Technology'' ``required'' for the ``production'' of fuel 
injection systems with a ``specially designed'' multifuel (e.g., 
diesel or jet fuel) capability covering a viscosity range from 
diesel fuel (2.5 cSt at 310.8 K (37.8 [deg]C)) down to gasoline fuel 
(0.5 cSt at 310.8 K (37.8 [deg]C)) and having all of the following:
    f.3.a. Injection amount in excess of 230 mm\3\ per injection per 
cylinder; and
    f.3.b. Electronic control features ``specially designed'' for 
switching governor characteristics automatically depending on fuel 
property to provide the same torque characteristics by using the 
appropriate sensors;
    g. ``Technology'' ``required'' for the ``development'' or 
``production'' of `high output diesel engines' for solid, gas phase 
or liquid film (or combinations thereof) cylinder wall lubrication 
and permitting operation to temperatures exceeding 723 K (450 
[deg]C), measured on the cylinder wall at the top limit of travel of 
the top ring of the piston;
    Technical Note:  ``High output diesel engines'' are diesel 
engines with a specified brake mean effective pressure of 1.8 MPa or 
more at a speed of 2,300 r.p.m., provided the rated speed is 2,300 
r.p.m. or more.
    h. ``Technology'' for gas turbine engine ``FADEC systems'' as 
follows:
    h.1. ``Development'' ``technology'' for deriving the functional 
requirements for the ``parts'' or ``components'' necessary for the 
``FADEC system'' to regulate engine thrust or shaft power (e.g., 
feedback sensor time constants and accuracies, fuel valve slew 
rate);
    h.2. ``Development'' or ``production'' ``technology'' for 
control and diagnostic ``parts'' or ``components'' unique to the 
``FADEC system'' and used to regulate engine thrust or shaft power;
    h.3. ``Development'' ``technology'' for the control law 
algorithms, including ``source code'', unique to the ``FADEC 
system'' and used to regulate engine thrust or shaft power;
    Note:  9E003.h does not apply to technical data related to 
engine-``aircraft'' integration required by civil aviation 
authorities of one or more Wassenaar Arrangement Participating 
States (See Supplement No. 1 to part 743 of the EAR) to be published 
for general airline use e.g., installation manuals, operating 
instructions, instructions for continued airworthiness) or interface 
functions e.g. input/output processing, airframe thrust or shaft 
power demand).
    i. ``Technology'' for adjustable flow path systems designed to 
maintain engine stability for gas generator turbines, fan or power 
turbines, or propelling nozzles, as follows:
    i.1. ``Development'' ``technology'' for deriving the functional 
requirements for the ``parts'' or ``components'' that maintain 
engine stability;
    i.2. ``Development'' or ``production'' ``technology'' for 
``parts'' or ``components'' unique to the adjustable flow path 
system and that maintain engine stability;
    i.3. ``Development'' ``technology'' for the control law 
algorithms, including ``source code'', unique to the adjustable flow 
path system and that maintain engine stability;
    Note: 9E003.i does not apply to ``technology'' for any of the 
following:
    a. Inlet guide vanes;
    b. Variable pitch fans or prop-fans;
    c. Variable compressor vanes;
    d. Compressor bleed valves; or
    e. Adjustable flow path geometry for reverse thrust.
    j. ``Technology'' ``required'' for the ``development'' of wing-
folding systems designed for fixed-wing ``aircraft'' powered by gas 
turbine engines.
    N.B.: For ``technology'' ``required'' for the ``development'' of 
wing-folding systems designed for fixed-wing ``aircraft'' specified 
in USML Category VIII (a), see USML Category VIII (i).
    k. ``Technology'' not otherwise controlled in 9E003.a.1 through 
a.8, a.10, and .h and used in the ``development'', ``production'', 
or overhaul of hot section ``parts'' or ``components'' of civil 
derivatives of military engines controlled on the U.S. Munitions 
List.
* * * * *

0
13. Effective March 14, 2023, amend supplement no. 1 to part 774 under 
Category 4, by revising ECCNs 4A003, 4D001, and 4E001 to read as 
follows:

Supplement No. 1 to Part 774--The Commerce Control List

* * * * *

[[Page 12130]]

Category 4--Computers

* * * * *
4A003 ``Digital computers'', ``electronic assemblies'', and related 
equipment therefor, as follows (see List of Items Controlled) and 
``specially designed'' ``components'' therefor.

License Requirements

Reason for Control: NS, CC, AT

 
                                            Country chart (see Supp. No.
                Control(s)                         1 to part 738)
 
NS applies to 4A003.b and .c..............  NS Column 1.
NS applies to 4A003.g.....................  NS Column 2.
CC applies to ``digital computers'' for     CC Column 1.
 computerized finger-print equipment.
AT applies to entire entry (refer to 4A994  AT Column 1.
 for controls on ``digital computers''
 with a APP > 0.0128 but <= 70 WT).
 

    Note: For all destinations, except those countries in Country 
Group E:1 or E:2 of Supplement No. 1 to part 740 of the EAR, no 
license is required (NLR) for computers with an ``Adjusted Peak 
Performance'' (``APP'') not exceeding 70 Weighted TeraFLOPS (WT) and 
for ``electronic assemblies'' described in 4A003.c that are not 
capable of exceeding an ``Adjusted Peak Performance'' (``APP'') 
exceeding 70 Weighted TeraFLOPS (WT) in aggregation, except certain 
transfers as set forth in Sec.  746.3 (Iraq).

Reporting Requirements

    Special Post Shipment Verification reporting and recordkeeping 
requirements for exports of computers to destinations in Computer 
Tier 3 may be found in Sec.  743.2 of the EAR.

List Based License Exceptions (See Part 740 for a Description of All 
License Exceptions)

LVS: $5000; N/A for 4A003.b and .c.
GBS: Yes, for 4A003.g and ``specially designed'' ``parts'' and 
``components'' therefor, exported separately or as part of a system.
APP: Yes, for computers controlled by 4A003.b, and ``electronic 
assemblies'' controlled by 4A003.c, to the exclusion of other 
technical parameters. See Sec.  740.7 of the EAR.

List of Items Controlled

Related Controls: See also 4A994 and 4A980
Related Definitions: N/A
Items:

    Note 1: 4A003 includes the following:
    --``Vector processors'' (as defined in Note 7 of the ``Technical 
Note on ``Adjusted Peak Performance'' (``APP'')'');
    --Array processors;
    --Digital signal processors;
    --Logic processors;
    --Equipment designed for ``image enhancement.''
    Note 2: The control status of the ``digital computers'' and 
related equipment described in 4A003 is determined by the control 
status of other equipment or systems provided:
    a. The ``digital computers'' or related equipment are essential 
for the operation of the other equipment or systems;
    b. The ``digital computers'' or related equipment are not a 
``principal element'' of the other equipment or systems; and
    N.B. 1:  The control status of ``signal processing'' or ``image 
enhancement'' equipment ``specially designed'' for other equipment 
with functions limited to those required for the other equipment is 
determined by the control status of the other equipment even if it 
exceeds the ``principal element'' criterion.
    N.B. 2: For the control status of ``digital computers'' or 
related equipment for telecommunications equipment, see Category 5, 
Part 1 (Telecommunications).
    c. The ``technology'' for the ``digital computers'' and related 
equipment is determined by 4E.
    a. [Reserved]
    b. ``Digital computers'' having an ``Adjusted Peak Performance'' 
(``APP'') exceeding 70 Weighted TeraFLOPS (WT);
    c. ``Electronic assemblies'' ``specially designed'' or modified 
to be capable of enhancing performance by aggregation of processors 
so that the ``APP'' of the aggregation exceeds the limit in 
4A003.b.;
    Note 1: 4A003.c applies only to ``electronic assemblies'' and 
programmable interconnections not exceeding the limit in 4A003.b 
when shipped as unintegrated ``electronic assemblies.''
    Note 2: 4A003.c does not control ``electronic assemblies'' 
``specially designed'' for a product or family of products whose 
maximum configuration does not exceed the limit of 4A003.b.
    d. to f. [Reserved]
    N.B.: For ``electronic assemblies,'' modules or equipment, 
performing analog-to-digital conversions, see 3A002.h.
    g. Equipment ``specially designed'' for aggregating the 
performance of ``digital computers'' by providing external 
interconnections which allow communications at unidirectional data 
rates exceeding 2.0 Gbyte/s per link.
    Note:  4A003.g does not control internal interconnection 
equipment (e.g., backplanes, buses) passive interconnection 
equipment, ``network access controllers'' or ``communication channel 
controllers''.
* * * * *
4D001 ``Software'' as follows (see List of Items Controlled).

License Requirements

Reason for Control: NS, CC, AT

 
                                            Country chart (see Supp. No.
                Control(s)                         1 to part 738)
 
NS applies to entire entry................  NS Column 1.
CC applies to ``software'' for              CC Column 1.
 computerized finger-print equipment
 controlled by 4A003 for CC reasons.
AT applies to entire entry................  AT Column 1.
 

Reporting Requirements

See Sec.  743.1 of the EAR for reporting requirements for exports 
under License Exceptions, and Validated End-User authorizations.

List Based License Exceptions (See Part 740 for a Description of All 
License Exceptions)

TSR: Yes, except for ``software'' for the ``development'' or 
``production'' of commodities with an ``Adjusted Peak Performance'' 
(``APP'') exceeding 70 WT.
APP: Yes to specific countries (see Sec.  740.7 of the EAR for 
eligibility criteria)

Special Conditions for STA

STA: License Exception STA may not be used to ship or transmit 
``software'' ``specially designed'' for the ``development'' or 
``production'' of equipment specified by ECCN 4A001.a.2 or for the 
``development'' or ``production'' of ``digital computers'' having an 
`Adjusted Peak Performance' (`APP') exceeding 70 Weighted TeraFLOPS 
(WT) to any of the destinations listed in Country Group A:6 (See 
Supplement No.1 to part 740 of the EAR).

List of Items Controlled

Related Controls: N/A
Related Definitions: N/A
Items:

    a. ``Software'' ``specially designed'' or modified for the 
``development'' or ``production'', of equipment or ``software'' 
controlled by 4A001, 4A003, 4A004, or 4D (except 4D090, 4D980, 4D993 
or 4D994).
    b. ``Software'', other than that controlled by 4D001.a, 
``specially designed'' or modified for the ``development'' or 
``production'' of equipment as follows:
    b.1. ``Digital computers'' having an ``Adjusted Peak 
Performance'' (``APP'') exceeding 15 Weighted TeraFLOPS (WT);
    b.2. ``Electronic assemblies'' ``specially designed'' or 
modified for enhancing performance by aggregation of processors so 
that the ``APP'' of the aggregation exceeds the limit in 4D001.b.1.
* * * * *
4E001 ``Technology'' as follows (see List of Items Controlled).

License Requirements

Reason for Control: NS, MT, RS, CC, AT

[[Page 12131]]



 
                                            Country chart (see Supp. No.
                Control(s)                         1 to part 738)
 
NS applies to entire entry, except 4A090    NS Column 1.
 or ``software'' specified by 4D090.
MT applies to ``technology'' for items      MT Column 1.
 controlled by 4A001.a and 4A101 for MT
 reasons.
RS applies to ``technology'' for            China and Macau (See Sec.
 commodities controlled by 4A090 or          742.6(a)(6)).
 ``software'' specified by 4D090.
CC applies to ``software'' for              CC Column 1.
 computerized finger-print equipment
 controlled by 4A003 for CC reasons.
AT applies to entire entry................  AT Column 1.
 

Reporting Requirements

    See Sec.  743.1 of the EAR for reporting requirements for 
exports under License Exceptions, and Validated End-User 
authorizations.

List Based License Exceptions (See Part 740 for a Description of All 
License Exceptions)

TSR: Yes, except for ``technology'' for the ``development'' or 
``production'' of commodities with an ``Adjusted Peak Performance'' 
(``APP'') exceeding 70 WT.
APP: Yes to specific countries (see Sec.  740.7 of the EAR for 
eligibility criteria).

Special Conditions for STA

STA: License Exception STA may not be used to ship or transmit 
``technology'' according to the General Technology Note for the 
``development'' or ``production'' of any of the following equipment 
or ``software'': a. Equipment specified by ECCN 4A001.a.2; b. 
``Digital computers'' having an `Adjusted Peak Performance' (`APP') 
exceeding 70 Weighted TeraFLOPS (WT); or c. ``software'' specified 
in the License Exception STA paragraph found in the License 
Exception section of ECCN 4D001 to any of the destinations listed in 
Country Group A:6 (See Supplement No. 1 to part 740 of the EAR).

List of Items Controlled

Related Controls: N/A
Related Definitions: N/A
Items:

    a. ``Technology'' according to the General Technology Note, for 
the ``development'' ``production'' or ``use'' of equipment or 
``software'' controlled by 4A (except 4A980 or 4A994) or 4D (except 
4D980, 4D993, 4D994).
    b. ``Technology'' according to the General Technology Note, 
other than that controlled by 4E001.a, for the ``development'' or 
``production'' of equipment as follows:
    b.1. ``Digital computers'' having an ``Adjusted Peak 
Performance'' (``APP'') exceeding 15 Weighted TeraFLOPS (WT);
    b.2. ``Electronic assemblies'' ``specially designed'' or 
modified for enhancing performance by aggregation of processors so 
that the ``APP'' of the aggregation exceeds the limit in 4E001.b.1.
    c. ``Technology'' for the ``development'' of ``intrusion 
software.''
    Note 1:  4E001.a and 4E001.c do not apply to ``vulnerability 
disclosure'' or ``cyber incident response''.
    Note 2: Note 1 does not diminish national authorities' rights to 
ascertain compliance with 4E001.a and 4E001.c.
* * * * *

Matthew S. Borman,
Deputy Assistant Secretary for Export Administration.
[FR Doc. 2023-03683 Filed 2-23-23; 8:45 am]
BILLING CODE 3510-33-P


